Add support for the new MDP5 display controller block.  The mapping
between parts of the display controller and KMS is:

  plane   -> PIPE{RGBn,VIGn}             \
  crtc    -> LM (layer mixer)            |-> MDP "device"
  encoder -> INTF                        /
  connector -> HDMI/DSI/eDP/etc          --> other device(s)

Unlike MDP4, it appears we can get by with a single encoder, rather
than needing a different implementation for DTV, DSI, etc.  (Ie. the
register interface is same, just different bases.)

Also unlike MDP4, all the IRQs for other blocks (HDMI, DSI, etc) are
routed through MDP.

And finally, MDP5 has this "Shared Memory Pool" (called "SMP"), from
which blocks need to be allocated to the active pipes based on fetch
stride.
Signed-off-by: Rob Clark <robdclark@gmail.com>

The HDMI block is basically the same between older SoC's with mdp4
display controller, and newer ones with mdp5.

So mostly this consists of better abstracting out the different sets of
regulators, clks, etc.  In particular, for regulators and clks we can
split it up by what is needed for hot plug detect to work, and what is
needed to light up the display.

Also, 8x74 has a new phy.. a very simple one, but split out into a
different mmio space.  And with mdp5, the irq is shared with mdp, so we
don't directly register our own irq handler.
Signed-off-by: Rob Clark <robdclark@gmail.com>

We'll want basically the same thing for mdp5, so refactor it out so it
can be shared.
Signed-off-by: Rob Clark <robdclark@gmail.com>

Signed-off-by: Rob Clark <robdclark@gmail.com>

This can be shared between mdp4 and mdp5.  Both use the same set of
parameters to describe the format to the hw.
Signed-off-by: Rob Clark <robdclark@gmail.com>

resync to latest envytools db, add mdp5 registers
Signed-off-by: Rob Clark <robdclark@gmail.com>

There are some little bits and pieces that mdp4 and mdp5 can share, so
move things around so that we can have both in a common parent
directory.
Signed-off-by: Rob Clark <robdclark@gmail.com>

This adds the necessary configuration for the APQ8060A SoC (dual-core
krait + a320 gpu) as found on the bstem board.
Signed-off-by: Rob Clark <robdclark@gmail.com>

Add a VRAM carveout that is used for systems which do not have an IOMMU.

The VRAM carveout uses CMA.  The arch code must setup a CMA pool for the
device (preferrably in highmem.. a 256m-512m VRAM pool in lowmem is not
cool).  The user can configure the VRAM pool size using msm.vram module
param.

Technically, the abstraction of IOMMU behind msm_mmu is not strictly
needed, but it simplifies the GEM code a bit, and will be useful later
when I add support for a2xx devices with GPUMMU, so I decided to keep
this part.

It appears to be possible to configure the GPU to restrict access to
addresses within the VRAM pool, but this is not done yet.  So for now
the GPU will refuse to load if there is no sort of mmu.  Once address
based limits are supported and tested to confirm that we aren't giving
the GPU access to arbitrary memory, this restriction can be lifted
Signed-off-by: Rob Clark <robdclark@gmail.com>

This got a bit broken with original patches when re-arranging things to
move dependencies on mach-msm inside #ifndef OF.
Signed-off-by: Rob Clark <robdclark@gmail.com>

Signed-off-by: Rob Clark <robdclark@gmail.com>

With a simple stub, we can get COMPILE_TEST support.
Signed-off-by: Rob Clark <robdclark@gmail.com>

Merge tag 'drm-intel-next-2013-12-13' of git://people.freedesktop.org/~danvet/drm-intel into drm-next

- fbc1 improvements from Ville (pre-gm45).
- vlv forcewake improvements from Deepak S.
- Some corner-cases fixes from Mika for the context hang stat code.
- pc8 improvements and prep work for runtime D3 from Paulo, almost ready for
  primetime.
- gen2 dpll fixes from Ville.
- DSI improvements from Shobhit Kumar.
- A few smaller fixes and improvements all over.

[airlied: intel_ddi.c conflict fixed up]

* tag 'drm-intel-next-2013-12-13' of git://people.freedesktop.org/~danvet/drm-intel: (61 commits)
  drm/i915/bdw: Implement ff workarounds
  drm/i915/bdw: Force all Data Cache Data Port access to be Non-Coherent
  drm/i915/bdw: Don't use forcewake needlessly
  drm/i915: Clear out old GT FIFO errors in intel_uncore_early_sanitize()
  drm/i915: dont call irq_put when irq test is on
  drm/i915: Rework the FBC interval/stall stuff a bit
  drm/i915: Enable FBC for all mobile gen2 and gen3 platforms
  drm/i915: FBC_CONTROL2 is gen4 only
  drm/i915: Gen2 FBC1 CFB pitch wants 32B units
  drm/i915: split intel_ddi_pll_mode_set in 2 pieces
  drm/i915: Fix timeout with missed interrupts in __wait_seqno
  drm/i915: touch VGA MSR after we enable the power well
  drm/i915: extract hsw_power_well_post_{enable, disable}
  drm/i915: remove i915_disable_vga_mem declaration
  drm/i915: Parametrize the dphy and other spec specific parameters
  drm/i915: Remove redundant DSI PLL enabling
  drm/i915: Reorganize the DSI enable/disable sequence
  drm/i915: Try harder to get best m, n, p values with minimal error
  drm/i915: Compute dsi_clk from pixel clock
  drm/i915: Use FLISDSI interface for band gap reset
  ...

Conflicts:
	drivers/gpu/drm/i915/intel_ddi.c

drm/tegra: Changes for v3.14-rc1

This series of changes brings DRM panel support as well as initial code
to register DSI hosts and peripherals and bind them to DSI drivers. The
panel and DSI code are both used by the simple panel driver.

The Tegra-specific changes build on top of this work to add support for
various panels found on Tegra boards. New drivers enable the DSI host
found on Tegra114 and a special hardware block that calibrates the pads
used for DSI and CSI. The host1x and the display controller drivers gain
basic Tegra124 support. To round of the new features, the DRM driver now
sports a very simple PRIME implementation.

In addition there are various improvements such as the host1x API being
exported so that client drivers (like the Tegra DRM driver) can be built
as modules. HDMI now does better power management and legacy FBDEV can
now be disabled via Kconfig (though it's still enabled by default). A
few sparse warnings have been squashed and various parts of the code
have become more robust.

* tag 'drm/for-3.14-rc1' of git://anongit.freedesktop.org/tegra/linux: (121 commits)
  drm/tegra: fix compile w/ CONFIG_DYNAMIC_DEBUG
  drm/tegra: Add PRIME support
  drm/tegra: Relocate some output-specific code
  drm/tegra: Add Tegra124 DC support
  drm/tegra: Fix small leak on error in tegra_fb_alloc()
  drm/tegra: Make legacy fbdev support optional
  drm/tegra: Sort reverse-dependencies alphabetically
  drm/tegra: Fix return value check
  drm/tegra: Add DSI support
  drm/tegra: Disable outputs for power-saving
  drm/tegra: Track HDMI enable state
  drm/tegra: Fix HDMI audio frequency typo
  drm/tegra: Do not export tegra_bo_ops
  drm/tegra: Remove spurious blank line
  drm/tegra: Increase compile test coverage
  drm/tegra: Allow the driver to be built as a module
  gpu: host1x: Add Tegra124 support
  gpu: host1x: clk_round_rate() can return a zero upon error
  gpu: host1x: Fix build warnings
  gpu: host1x: Increase compile test coverage
  ...

rcar misc changes.

* 'drm/next/du' of git://linuxtv.org/pinchartl/fbdev:
  drm/rcar-du: Add support for the r8a7791 DU
  drm/rcar-du: Add LVDS_LANES quirk
  drm/rcar-du: Split features and quirks
  drm/rcar-du: Update plane pitch in .mode_set_base() operation
  drm/rcar-du: Don't cast crtc to rcrtc twice in the same function
  drm/rcar-du: fix return value check in rcar_du_lvdsenc_get_resources()

With CONFIG_DYNAMIC_DEBUG=y, the following compile error occurs:

drivers/gpu/drm/tegra/mipi-phy.c: In function ‘mipi_dphy_timing_validate’:
drivers/gpu/drm/tegra/mipi-phy.c:69:11: error: ‘EINVAL’ undeclared (first use in this function)
drivers/gpu/drm/tegra/mipi-phy.c:69:11: note: each undeclared identifier is reported only once for each function it appears in

Fix this by directly including the header that defines EINVAL.

Fixes: dec72739 ("drm/tegra: Add DSI support")
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>

Implement very basic PRIME support. This currently only works with
buffers that are contiguous in memory and will refuse to import any
physically non-contiguous buffers.
Signed-off-by: Thierry Reding <treding@nvidia.com>

Some of the code in the CRTC's mode setting code is specific to the RGB
output or needs to be called slightly differently depending on the type
of output. Push that code down into the output drivers.
Signed-off-by: Thierry Reding <treding@nvidia.com>

Tegra124 and later support interlacing, but the driver doesn't support
it yet. Make sure interlacing stays disabled on hardware that supports
it.
Signed-off-by: Thierry Reding <treding@nvidia.com>

If we don't have enough memory for ->planes then we leak "fb".
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>

A lot of the modern userspace is capable of working without the legacy
fbdev support. kmscon can be used as a replacement for the framebuffer
console, and KMS X drivers create their own framebuffers.

Most people don't have a system where all of this works yet, though, so
leave support enabled by default.
Signed-off-by: Thierry Reding <treding@nvidia.com>

Move the TEGRA_HOST1X and DRM_KMS_HELPER entries around to keep the list
sorted.
Signed-off-by: Thierry Reding <treding@nvidia.com>

In case of error, the devm_ioremap_resource() function returns ERR_PTR()
and never NULL. The NULL test in the return value check should therefore
be replaced with IS_ERR().
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Thierry Reding <treding@nvidia.com>

This commit adds support for both DSI outputs found on Tegra. Only very
minimal functionality is implemented, so advanced features like ganged
mode won't work.

Due to the lack of other test hardware, some sections of the driver are
hardcoded to work with Dalmore.
Signed-off-by: Thierry Reding <treding@nvidia.com>

When an output is disabled, its DPMS mode is usually set to off. Instead
of only disabling the panel (if one is attached), turn the output off
entirely to save more power.

HDMI doesn't have any panels attached, so it previously didn't save any
power at all. With this commit, however, the complete HDMI interface
will be turned off, therefore allowing an attached monitor to go into a
standby mode.
Signed-off-by: Thierry Reding <treding@nvidia.com>

The DRM core doesn't track enable and disable state of encoders and/or
connectors, so calls to the output's .enable() and .disable() are not
guaranteed to be balanced. Track the enable state internally so that
calls to regulator and clock frameworks remain balanced.
Signed-off-by: Thierry Reding <treding@nvidia.com>

The correct check is for 48 kHz, not 480 kHz. Found by Coverity.
Signed-off-by: Thierry Reding <treding@nvidia.com>

These buffer object operations are never used outside of the GEM
implementation so there is no use in exporting them.
Signed-off-by: Thierry Reding <treding@nvidia.com>

Signed-off-by: Thierry Reding <treding@nvidia.com>

The ARCH_MULTIPLATFORM dependency was introduced back when Tegra didn't
support multiplatform yet as a means to allow the driver to be easily
compile-tested along with other DRM drivers. In the meantime, the new
COMPILE_TEST Kconfig option has been introduced for exactly that
purpose, so use that instead to clarify the intention.
Signed-off-by: Thierry Reding <treding@nvidia.com>

All APIs that the driver uses are exported, so the driver can now be
built as a module.
Signed-off-by: Thierry Reding <treding@nvidia.com>

Tegra124 has 192 syncpoints whereas its predecessors had 32 syncpoints.
This required changes to the hardware register layout.
Signed-off-by: Arto Merilainen <amerilainen@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>

Treat both negative and zero return values from clk_round_rate() as
errors.  This is needed since subsequent patches will convert
clk_round_rate()'s return value to be an unsigned type, rather than a
signed type, since some clock sources can generate rates higher than
(2^31)-1 Hz.

Eventually, when calling clk_round_rate(), only a return value of zero
will be considered a error.  All other values will be considered valid
rates.  The comparison against values less than 0 is kept to preserve
the correct behavior in the meantime.
Signed-off-by: Paul Walmsley <pwalmsley@nvidia.com>
Cc: Mikko Perttunen <mperttunen@nvidia.com>
Cc: Arto Merilainen <amerilainen@nvidia.com>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Terje Bergström <tbergstrom@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>

When debugfs support isn't enabled, gcc complains about some variables
being unused. To avoid further #ifdefery, move debugfs specific setup
code into static functions and use IS_ENABLED(CONFIG_DEBUG_FS) to have
the compiler, rather than the preprocessor, discard them when unused.
The advantage of doing it this way is that all the code will be
compile-tested whether or not debugfs support is enabled.
Signed-off-by: Thierry Reding <treding@nvidia.com>

The ARCH_MULTIPLATFORM dependency was introduced back when Tegra didn't
support multiplatform yet as a means to allow the driver to be easily
compile-tested along with other DRM drivers. In the meantime, the new
COMPILE_TEST Kconfig option has been introduced for exactly that
purpose, so use that instead to clarify the intention.
Signed-off-by: Thierry Reding <treding@nvidia.com>

Include the linux/host1x.h and dev.h headers so that function prototypes
are visible to keep sparse from suggesting that their implementations be
made static.
Signed-off-by: Thierry Reding <treding@nvidia.com>

An earlier patch added a subset of the required HW specific header files
but didn't actually include the right ones when compiling for host1x02.
Signed-off-by: Thierry Reding <treding@nvidia.com>

Make the public API symbols visible so that depending drivers can be
built as a module.
Signed-off-by: Thierry Reding <treding@nvidia.com>

This driver adds support to perform calibration of the MIPI pads for CSI
and DSI.
Signed-off-by: Thierry Reding <treding@nvidia.com>

  - DP_TEST_LINK_PATTERN is ambiguous, rename to DP_TEST_LINK_VIDEO_PATTERN to clarify
  - Added DP_TEST_LINK_FAUX_PATTERN to support automated testing of Fast AUX
Signed-off-by: Todd Previte <tprevite@gmail.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>