Set device resetting state at the earliest possible point: as soon as a
reset is successfully scheduled. The reset state is toggled off when
all resets have been processed to completion.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Instead of having one initialization routine for all cases, create
a separate, simpler function for standard initialization, such as during
device probe. Use the original initialization function to handle
device reset scenarios. The goal of this patch is to avoid having
a single, cluttered init function to handle all possible
scenarios.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

If setting the link state is not successful, print a warning
with the resulting return code and return it to be handled
by the caller.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

If device init is interrupted by a failover, set the init return
code so that it can be checked and handled appropriately by the
init routine.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Check whether CRQ command is successful before awaiting a response
from the management partition. If the command was not successful, the
driver may hang waiting for a response that will never come.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Introduce an "active" state for a IBM vNIC Command-Response Queue. A CRQ
is considered active once it has initialized or linked with its partner by
sending an initialization request and getting a successful response back
from the management partition.  Until this has happened, do not allow CRQ
commands to be sent other than the initialization request.

This change will avoid a protocol error in case of a device transport
event occurring during a initialization. When the driver receives a
transport event notification indicating that the backing hardware
has changed and needs reinitialization, any further commands other
than the initialization handshake with the VIOS management partition
will result in an invalid state error. Instead of sending a command
that will be returned with an error, print a warning and return an
error that will be handled by the caller.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Set adapter NAPI state as disabled if they are removed. This will allow
them to be enabled again if reallocated in case of a hard reset.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Petr Machata says:

====================
selftests: forwarding: Additions to mirror-to-gretap tests

This patchset is for a handful of edge cases in mirror-to-gretap
scenarios: removal of mirrored-to netdevice (#1), removal of underlay
route for tunnel remote endpoint (#2) and cessation of mirroring upon
removal of flower mirroring rule (#3).
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Test that when flower-based mirror action is removed, mirroring stops.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When underlay route is removed, the mirrored traffic should not be
forwarded.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Tests that the mirroring code catches up with deletion of a mirrored-to
device.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

t4_prep_fw doesn't check for card_fw pointer before store the read data,
which could lead to a NULL pointer dereference if kvzalloc failed.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In struct phy_device we have a number of flags being defined as type
bool. Similar to e.g. struct pci_dev we can save some space by using
bit-fields.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

Simon Wunderlich says:

====================
This feature/cleanup patchset includes the following patches:

 - bump version strings, by Simon Wunderlich

 - Disable batman-adv debugfs by default, by Sven Eckelmann

 - Improve handling mesh nodes with multicast optimizations disabled,
   by Linus Luessing

 - Avoid bool in structs, by Sven Eckelmann

 - Allocate less memory when debugfs is disabled, by Sven Eckelmann

 - Fix batadv_interface_tx return data type, by Luc Van Oostenryck

 - improve link speed handling for virtual interfaces, by Marek Lindner

 - Enable BATMAN V algorithm by default, by Marek Lindner
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Passing O_CREAT (00000100) to open means we should also pass file
mode as the third parameter.  Creating /dev/console as a regular
file may not be helpful anyway, so simply drop the flag when
opening debug_fd.

Fixes: d2ba09c1 ("net: add skeleton of bpfilter kernel module")
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

BPFILTER could have been enabled without INET causing this build error:
ERROR: "bpfilter_process_sockopt" [net/bpfilter/bpfilter.ko] undefined!

Fixes: d2ba09c1 ("net: add skeleton of bpfilter kernel module")
Reported-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pablo Neira Ayuso says:

====================
Netfilter updates for net-next

The following patchset contains Netfilter updates for your net-next
tree, they are:

1) Remove obsolete nf_log tracing from nf_tables, from Florian Westphal.

2) Add support for map lookups to numgen, random and hash expressions,
   from Laura Garcia.

3) Allow to register nat hooks for iptables and nftables at the same
   time. Patchset from Florian Westpha.

4) Timeout support for rbtree sets.

5) ip6_rpfilter works needs interface for link-local addresses, from
   Vincent Bernat.

6) Add nf_ct_hook and nf_nat_hook structures and use them.

7) Do not drop packets on packets raceing to insert conntrack entries
   into hashes, this is particularly a problem in nfqueue setups.

8) Address fallout from xt_osf separation to nf_osf, patches
   from Florian Westphal and Fernando Mancera.

9) Remove reference to struct nft_af_info, which doesn't exist anymore.
   From Taehee Yoo.

This batch comes with is a conflict between 25fd386e ("netfilter:
core: add missing __rcu annotation") in your tree and 2c205dd3
("netfilter: add struct nf_nat_hook and use it") coming in this batch.
This conflict can be solved by leaving the __rcu tag on
__netfilter_net_init() - added by 25fd386e - and remove all code
related to nf_nat_decode_session_hook - which is gone after
2c205dd3, as described by:

diff --cc net/netfilter/core.c
index e0ae4aae96f5,206fb2c4c319..168af54db975
--- a/net/netfilter/core.c
+++ b/net/netfilter/core.c
@@@ -611,7 -580,13 +611,8 @@@ const struct nf_conntrack_zone nf_ct_zo
  EXPORT_SYMBOL_GPL(nf_ct_zone_dflt);
  #endif /* CONFIG_NF_CONNTRACK */

- static void __net_init __netfilter_net_init(struct nf_hook_entries **e, int max)
 -#ifdef CONFIG_NF_NAT_NEEDED
 -void (*nf_nat_decode_session_hook)(struct sk_buff *, struct flowi *);
 -EXPORT_SYMBOL(nf_nat_decode_session_hook);
 -#endif
 -
+ static void __net_init
+ __netfilter_net_init(struct nf_hook_entries __rcu **e, int max)
  {
  	int h;

I can also merge your net-next tree into nf-next, solve the conflict and
resend the pull request if you prefer so.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Tom Lendacky says:

====================
amd-xgbe: AMD XGBE driver updates 2018-05-21

The following updates are included in this driver update series:

- Fix the debug output for the max channels count
- Read (once) and save the port property registers during probe
- Remove the use of the comm_owned field
- Remove unused SFP diagnostic support indicator field
- Add ethtool --module-info support
- Add ethtool --show-ring/--set-ring support
- Update the driver in preparation for ethtool --set-channels support
- Add ethtool --show-channels/--set-channels support
- Update the driver to always perform link training in KR mode
- Advertise FEC support when using a KR re-driver
- Update the BelFuse quirk to now support SGMII
- Improve 100Mbps auto-negotiation for BelFuse parts

This patch series is based on net-next.

---

Changes since v1:
- Update the --set-channels support to the use of the combined, rx and
  tx options as specified in the ethtool man page (in other words, don't
  create combined channels based on the min of the tx and rx channels
  specified).
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

After changing speed to 100Mbps as a result of auto-negotiation (AN),
some 10/100/1000Mbps SFPs indicate a successful link (no faults or loss
of signal), but cannot successfully transmit or receive data.  These
SFPs required an extra auto-negotiation (AN) after the speed change in
order to operate properly.  Add a quirk for these SFPs so that if the
outcome of the AN actually results in changing to a new speed, re-initiate
AN at that new speed.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Instead of using a quirk to make the BelFuse 1GBT-SFP06 part look like
a 1000baseX part, program the SFP PHY to support SGMII and 10/100/1000
baseT.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When a KR re-driver is present, indicate the FEC support is available
during auto-negotiation.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Link training is always attempted when in KR mode, but the code is
structured to check if link training has been enabled before attempting
to perform it.  Since that check will always be true, simplify the code
to always enable and start link training during KR auto-negotiation.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add ethtool support to show and set the device channel configuration.
Changing the channel configuration will result in a device restart.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In order to support being able to dynamically set/change the number of
Rx and Tx channels, update the code to:
 - Move alloc and free of device memory into callable functions
 - Move setting of the real number of Rx and Tx channels to device startup
 - Move mapping of the RSS channels to device startup
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add ethtool support to show and set the number of the Rx and Tx ring
descriptors.  Changing the ring configuration will result in a device
restart.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add support to get SFP module information using ethtool.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The driver currently sets an indication of whether the SFP supports, and
that the driver can obtain, diagnostics data.  This isn't currently used
by the driver and the logic to set this indicator is flawed because the
field is cleared each time the SFP is checked and only set when a new SFP
is detected.  Remove this field and the logic supporting it.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The comm_owned field can hide logic where double locking is attempted
and prevent multiple threads for the same device from accessing the
mutex properly.  Remove the comm_owned field and use the mutex API
exclusively for gaining ownership.  The current driver has been audited
and is obtaining communications ownership properly.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Read and save the port property registers once during the device probe
and then use the saved values as they are needed.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

A debug output print statement uses the wrong variable to output the
maximum Rx channel count (cut and paste error, basically).  Fix the
statement to use the proper variable.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Ursula Braun says:

====================
patches 2018-05-23

here are more smc-patches for net-next:

Patch 1 fixes an ioctl problem detected by syzbot.

Patch 2 improves smc_lgr_list locking in case of abnormal link
group termination. If you want to receive a version for the net-tree,
please let me know. It would look somewhat different, since the port
terminate code has been moved to smc_core.c on net-next.

Patch 3 enables SMC to deal with urgent data.

Patch 4 is a minor improvement to avoid out-of-sync linkgroups
between 2 peers.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Client link group creation always follows the server linkgroup creation.
If peer creates a new server link group, client has to create a new
client link group. If peer reuses a server link group for a new
connection, client has to reuse its client link group as well. To
avoid out-of-sync conditions for link groups a longer delay for
for client link group removal is defined to make sure this link group
still exists, once the peer decides to reuse a server link group.

Currently the client link group delay time is just 10 jiffies larger
than the server link group delay time. This patch increases the delay
difference to 10 seconds to have a better protection against
out-of-sync link groups.
Signed-off-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add support for out of band data send and receive.
Signed-off-by: Stefan Raspl <raspl@linux.ibm.com>
Signed-off-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Currently, smc_port_terminate() is not holding the lock of the lgr list
while it is traversing the list. This patch adds locking to this
function and changes smc_lgr_terminate() accordingly.
Signed-off-by: Hans Wippel <hwippel@linux.ibm.com>
Signed-off-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

A connected SMC-socket contains addresses of descriptors for the
send buffer and the rmb (receive buffer). Fields of these descriptors
are used to determine the answer for certain ioctl requests.
Add extra handling for unconnected SMC socket states without valid
buffer descriptor addresses.
Signed-off-by: Ursula Braun <ubraun@linux.ibm.com>
Reported-by: syzbot+e6714328fda813fc670f@syzkaller.appspotmail.com
Signed-off-by: David S. Miller <davem@davemloft.net>

trigger an L1 configure operation when a transceiver module
is inserted in order to cause current "sticky" options like
Requested Forward Error Correction to be reapplied.
Signed-off-by: Casey Leedom <leedom@chelsio.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

MDI Port Capabilities bit definitions were inconsistent with
regard to the MDI enum values. 2 bits used to define MDI in
the port capabilities are not really separable, it's a 2-bit
field with 4 different values. Change the port capability bit
definitions to be "AUTO" and "STRAIGHT" in order to get them
to line up with the enum's.
Signed-off-by: Casey Leedom <leedom@chelsio.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge tag 'mac80211-next-for-davem-2018-05-23' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next

Johannes Berg says:

For this round, we have various things all over the place, notably
 * a fix for a race in aggregation, which I want to let
   bake for a bit longer before sending to stable
 * some new statistics (ACK RSSI, TXQ)
 * TXQ configuration
 * preparations for HE, particularly radiotap
 * replace confusing "country IE" by "country element" since it's
   not referring to Ireland

Note that I merged net-next to get a fix from mac80211 that got
there via net, to apply one patch that would otherwise conflict.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Michal Vokáč says:

====================
Add support for QCA8334 switch

This series basically adds support for a QCA8334 ethernet switch to the
qca8k driver. It is a four-port variant of the already supported seven
port QCA8337. Register map is the same for the whole familly and all chips
have the same device ID.

Major part of this series enhances the CPU port setting. Currently the CPU
port is not set to any sensible defaults compatible with the xGMII
interface. This series forces the CPU port to its maximum bandwidth and
also allows to adjust the new defaults using fixed-link device tree
sub-node.

Alongside these changes I fixed two checkpatch warnings regarding SPDX and
redundant parentheses.

Changes in v3:
 - Rebased on latest net-next/master.
 - Corrected fixed-link documentation.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Fix warning reported by checkpatch.
Signed-off-by: Michal Vokáč <michal.vokac@ysoft.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>