- 18 Sep, 2015 32 commits
-
-
K. Y. Srinivasan authored
commit 8de58074 upstream. We may exit this function without properly freeing up the maapings we may have acquired. Fix the bug. Signed-off-by: K. Y. Srinivasan <kys@microsoft.com> Reviewed-by: Long Li <longli@microsoft.com> Signed-off-by: James Bottomley <JBottomley@Odin.com> Signed-off-by: Zefan Li <lizefan@huawei.com>
-
Aravind Gopalakrishnan authored
commit b4491592 upstream. The comment line regarding IOMMU_INIT and IOMMU_INIT_FINISH macros is incorrect: "The standard vs the _FINISH differs in that the _FINISH variant will continue detecting other IOMMUs in the call list..." It should be "..the *standard* variant will continue detecting..." Fix that. Also, make it readable while at it. Signed-off-by: Aravind Gopalakrishnan <Aravind.Gopalakrishnan@amd.com> Signed-off-by: Borislav Petkov <bp@suse.de> Cc: H. Peter Anvin <hpa@zytor.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: konrad.wilk@oracle.com Fixes: 6e963669 ("x86, iommu: Update header comments with appropriate naming") Link: http://lkml.kernel.org/r/1428508017-5316-1-git-send-email-Aravind.Gopalakrishnan@amd.comSigned-off-by: Ingo Molnar <mingo@kernel.org> Signed-off-by: Zefan Li <lizefan@huawei.com>
-
Nicolas Dichtel authored
commit 5b5800fa upstream. These commands are missing. Fixes: 28d8909b ("[XFRM]: Export SAD info.") Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com> Signed-off-by: David S. Miller <davem@davemloft.net> [lizf: Backported to 3.4: adjust context] Signed-off-by: Zefan Li <lizefan@huawei.com>
-
Nicolas Dichtel authored
commit 5e6deeba upstream. This command is missing. Fixes: ecfd6b18 ("[XFRM]: Export SPD info") Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com> Signed-off-by: David S. Miller <davem@davemloft.net> [lizf: Backported to 3.4: adjust context] Signed-off-by: Zefan Li <lizefan@huawei.com>
-
Sowmini Varadhan authored
commit ebe96e64 upstream. AF_RDS, PF_RDS and SOL_RDS are available in header files, and there is no need to get their values from /proc. Document this correctly. Fixes: 0c5f9b88 ("RDS: Documentation") Signed-off-by: Sowmini Varadhan <sowmini.varadhan@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Zefan Li <lizefan@huawei.com>
-
Ulrik De Bie authored
commit bd884149 upstream. On ASUS TP500LN and X750JN, the touchpad absolute mode is reset each time set_rate is done. In order to fix this, we will verify the firmware version, and if it matches the one in those laptops, the set_rate function is overloaded with a function elantech_set_rate_restore_reg_07 that performs the set_rate with the original function, followed by a restore of reg_07 (the register that sets the absolute mode on elantech v4 hardware). Also the ASUS TP500LN and X750JN firmware version, capabilities, and button constellation is added to elantech.c Reported-and-tested-by: George Moutsopoulos <gmoutso@yahoo.co.uk> Signed-off-by: Ulrik De Bie <ulrik.debie-os@e2big.org> Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com> Signed-off-by: Zefan Li <lizefan@huawei.com>
-
Alexander Duyck authored
commit 2e7056c4 upstream. Looking over the implementation for jhash2 and comparing it to jhash_3words I realized that the two hashes were in fact very different. Doing a bit of digging led me to "The new jhash implementation" in which lookup2 was supposed to have been replaced with lookup3. In reviewing the patch I noticed that jhash2 had originally initialized a and b to JHASH_GOLDENRATIO and c to initval, but after the patch a, b, and c were initialized to initval + (length << 2) + JHASH_INITVAL. However the changes in jhash_3words simply replaced the initialization of a and b with JHASH_INITVAL. This change corrects what I believe was an oversight so that a, b, and c in jhash_3words all have the same value added consisting of initval + (length << 2) + JHASH_INITVAL so that jhash2 and jhash_3words will now produce the same hash result given the same inputs. Fixes: 60d509c8 ("The new jhash implementation") Signed-off-by: Alexander Duyck <alexander.h.duyck@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Zefan Li <lizefan@huawei.com>
-
Lukas Czerner authored
commit e12fb972 upstream. Previously commit 14ece102 added a support for for syncing parent directory of newly created inodes to make sure that the inode is not lost after a power failure in no-journal mode. However this does not work in majority of cases, namely: - if the directory has inline data - if the directory is already indexed - if the directory already has at least one block and: - the new entry fits into it - or we've successfully converted it to indexed So in those cases we might lose the inode entirely even after fsync in the no-journal mode. This also includes ext2 default mode obviously. I've noticed this while running xfstest generic/321 and even though the test should fail (we need to run fsck after a crash in no-journal mode) I could not find a newly created entries even when if it was fsynced before. Fix this by adjusting the ext4_add_entry() successful exit paths to set the inode EXT4_STATE_NEWENTRY so that fsync has the chance to fsync the parent directory as well. Signed-off-by: Lukas Czerner <lczerner@redhat.com> Signed-off-by: Theodore Ts'o <tytso@mit.edu> Reviewed-by: Jan Kara <jack@suse.cz> Cc: Frank Mayhar <fmayhar@google.com> [lizf: Backported to 3.4: remove a change from return to goto, as that doesn't exist in 3.4] Signed-off-by: Zefan Li <lizefan@huawei.com>
-
Pascal Huerst authored
commit 74ff9602 upstream. The delay time after a reset in the codec probe callback was too short, and did not work on certain hw because the codec needs more time to power on. This increases the delay time from 1us to 1ms. Signed-off-by: Pascal Huerst <pascal.huerst@gmail.com> Acked-by: Brian Austin <brian.austin@cirrus.com> Signed-off-by: Mark Brown <broonie@kernel.org> [lizf: Backported to 3.4: adjust context] Signed-off-by: Zefan Li <lizefan@huawei.com>
-
Larry Finger authored
commit 2f92b314 upstream. USB ID 2001:330d is used for a D-Link DWA-131. Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Signed-off-by: Zefan Li <lizefan@huawei.com>
-
Andrey Ryabinin authored
commit 8defb336 upstream. Usually ELF_ET_DYN_BASE is 2/3 of TASK_SIZE. With 3G/1G user/kernel split this is not so, because 2*TASK_SIZE overflows 32 bits, so the actual value of ELF_ET_DYN_BASE is: (2 * TASK_SIZE / 3) = 0x2a000000 When ASLR is disabled PIE binaries will load at ELF_ET_DYN_BASE address. On 32bit platforms AddressSanitzer uses addresses [0x20000000 - 0x40000000] for shadow memory [1]. So ASan doesn't work for PIE binaries when ASLR disabled as it fails to map shadow memory. Also after Kees's 'split ET_DYN ASLR from mmap ASLR' patchset PIE binaries has a high chance of loading somewhere in between [0x2a000000 - 0x40000000] even if ASLR enabled. This makes ASan with PIE absolutely incompatible. Fix overflow by dividing TASK_SIZE prior to multiplying. After this patch ELF_ET_DYN_BASE equals to (for CONFIG_VMSPLIT_3G=y): (TASK_SIZE / 3 * 2) = 0x7f555554 [1] https://code.google.com/p/address-sanitizer/wiki/AddressSanitizerAlgorithm#MappingSigned-off-by: Andrey Ryabinin <a.ryabinin@samsung.com> Reported-by: Maria Guseva <m.guseva@samsung.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk> Signed-off-by: Zefan Li <lizefan@huawei.com>
-
David Sterba authored
commit 3c3b04d1 upstream. Due to insufficient check in btrfs_is_valid_xattr, this unexpectedly works: $ touch file $ setfattr -n user. -v 1 file $ getfattr -d file user.="1" ie. the missing attribute name after the namespace. Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=94291Reported-by: William Douglas <william.douglas@intel.com> Signed-off-by: David Sterba <dsterba@suse.cz> Signed-off-by: Chris Mason <clm@fb.com> [lizf: Backported to 3.4: - 3.4 doesn't support XATTR_BTRFS_PREFIX] Signed-off-by: Zefan Li <lizefan@huawei.com>
-
Filipe Manana authored
commit dcc82f47 upstream. While committing a transaction we free the log roots before we write the new super block. Freeing the log roots implies marking the disk location of every node/leaf (metadata extent) as pinned before the new super block is written. This is to prevent the disk location of log metadata extents from being reused before the new super block is written, otherwise we would have a corrupted log tree if before the new super block is written a crash/reboot happens and the location of any log tree metadata extent ended up being reused and rewritten. Even though we pinned the log tree's metadata extents, we were issuing a discard against them if the fs was mounted with the -o discard option, resulting in corruption of the log tree if a crash/reboot happened before writing the new super block - the next time the fs was mounted, during the log replay process we would find nodes/leafs of the log btree with a content full of zeroes, causing the process to fail and require the use of the tool btrfs-zero-log to wipeout the log tree (and all data previously fsynced becoming lost forever). Fix this by not doing a discard when pinning an extent. The discard will be done later when it's safe (after the new super block is committed) at extent-tree.c:btrfs_finish_extent_commit(). Fixes: e688b725 (Btrfs: fix extent pinning bugs in the tree log) Signed-off-by: Filipe Manana <fdmanana@suse.com> Signed-off-by: Chris Mason <clm@fb.com> Signed-off-by: Zefan Li <lizefan@huawei.com>
-
K. Y. Srinivasan authored
commit 73cffdb6 upstream. Don't wait after sending request for offers to the host. This wait is unnecessary and simply adds 5 seconds to the boot time. Signed-off-by: K. Y. Srinivasan <kys@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> [lizf: Backported to 3.4: adjust context] Signed-off-by: Zefan Li <lizefan@huawei.com>
-
Nishanth Menon authored
commit f4831605 upstream. time_init invokes timer64_init (which is __init annotation) since all of these are invoked at init time, lets maintain consistency by ensuring time_init is marked appropriately as well. This fixes the following warning with CONFIG_DEBUG_SECTION_MISMATCH=y WARNING: vmlinux.o(.text+0x3bfc): Section mismatch in reference from the function time_init() to the function .init.text:timer64_init() The function time_init() references the function __init timer64_init(). This is often because time_init lacks a __init annotation or the annotation of timer64_init is wrong. Fixes: 546a3954 ("C6X: time management") Signed-off-by: Nishanth Menon <nm@ti.com> Signed-off-by: Mark Salter <msalter@redhat.com> Signed-off-by: Zefan Li <lizefan@huawei.com>
-
Brian Norris authored
commit 299d0c5b upstream. The comparison from the previous line seems to have been erroneously (partially) copied-and-pasted onto the next. The second line should be checking req.bytes, not req.lnum. Coverity CID #139400 Signed-off-by: Brian Norris <computersforpeace@gmail.com> [rw: Fixed comparison] Signed-off-by: Richard Weinberger <richard@nod.at> Signed-off-by: Zefan Li <lizefan@huawei.com>
-
Brian Norris authored
commit f16db807 upstream. In some of the 'out_not_moved' error paths, lnum may be used uninitialized. Don't ignore the warning; let's fix it. This uninitialized variable doesn't have much visible effect in the end, since we just schedule the PEB for erasure, and its LEB number doesn't really matter (it just gets printed in debug messages). But let's get it straight anyway. Coverity CID #113449 Signed-off-by: Brian Norris <computersforpeace@gmail.com> Signed-off-by: Richard Weinberger <richard@nod.at> [lizf: Backported to 3.4: adjust context] Signed-off-by: Zefan Li <lizefan@huawei.com>
-
Brian Norris authored
commit d74adbdb upstream. If aeb->len >= vol->reserved_pebs, we should not be writing aeb into the PEB->LEB mapping. Caught by Coverity, CID #711212. Signed-off-by: Brian Norris <computersforpeace@gmail.com> Signed-off-by: Richard Weinberger <richard@nod.at> [lizf: Backported to 3.4: adjust context] Signed-off-by: Zefan Li <lizefan@huawei.com>
-
Sudip Mukherjee authored
commit 2c20d92d upstream. the lcd type as defined in the Kconfig is not matching in the code. as a result the rs, rw and en pins were getting interchanged. Kconfig defines the value of PANEL_LCD to be 1 if we select custom configuration but in the code LCD_TYPE_CUSTOM is defined as 5. my hardware is LCD_TYPE_CUSTOM, but the pins were assigned to it as pins of LCD_TYPE_OLD, and it was not working. Now values are corrected with referenece to the values defined in Kconfig and it is working. checked on JHD204A lcd with LCD_TYPE_CUSTOM configuration. Signed-off-by: Sudip Mukherjee <sudip@vectorindia.org> Acked-by: Willy Tarreau <w@1wt.eu> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> [lizf: Backported to 3.4: adjust context] Signed-off-by: Zefan Li <lizefan@huawei.com>
-
Oliver Neukum authored
commit 323ece54 upstream. Values directly from descriptors given in debug statements must be converted to native endianness. Signed-off-by: Oliver Neukum <oneukum@suse.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Zefan Li <lizefan@huawei.com>
-
Sergej Sawazki authored
commit 8787041d upstream. The WM8741 DAC supports the following typical audio sampling rates: 44.1kHz, 88.2kHz, 176.4kHz (eg: with a master clock of 22.5792MHz) 32kHz, 48kHz, 96kHz, 192kHz (eg: with a master clock of 24.576MHz) For the rates lists, we should use 82000 instead of 88235, 176400 instead of 1764000 and 192000 instead of 19200 (seems to be a typo). Signed-off-by: Sergej Sawazki <ce3a@gmx.de> Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com> Signed-off-by: Mark Brown <broonie@kernel.org> [lizf: Backported to 3.4: adjust context] Signed-off-by: Zefan Li <lizefan@huawei.com>
-
Peter Chen authored
commit 990919ca upstream. We should signal connect (pull up dp) after we have already at peripheral mode, otherwise, the dp may be toggled due to we reset controller or do disconnect during the initialization for peripheral, then, the host may be confused during the enumeration, eg, it finds the reset can't succeed, but the device is still there, see below error message. hub 1-0:1.0: USB hub found hub 1-0:1.0: 1 port detected hub 1-0:1.0: cannot reset port 1 (err = -32) hub 1-0:1.0: cannot reset port 1 (err = -32) hub 1-0:1.0: cannot reset port 1 (err = -32) hub 1-0:1.0: cannot reset port 1 (err = -32) hub 1-0:1.0: cannot reset port 1 (err = -32) hub 1-0:1.0: Cannot enable port 1. Maybe the USB cable is bad? hub 1-0:1.0: cannot reset port 1 (err = -32) hub 1-0:1.0: cannot reset port 1 (err = -32) hub 1-0:1.0: cannot reset port 1 (err = -32) hub 1-0:1.0: cannot reset port 1 (err = -32) hub 1-0:1.0: cannot reset port 1 (err = -32) hub 1-0:1.0: Cannot enable port 1. Maybe the USB cable is bad? hub 1-0:1.0: cannot reset port 1 (err = -32) hub 1-0:1.0: cannot reset port 1 (err = -32) hub 1-0:1.0: cannot reset port 1 (err = -32) hub 1-0:1.0: cannot reset port 1 (err = -32) hub 1-0:1.0: cannot reset port 1 (err = -32) hub 1-0:1.0: Cannot enable port 1. Maybe the USB cable is bad? hub 1-0:1.0: cannot reset port 1 (err = -32) hub 1-0:1.0: cannot reset port 1 (err = -32) hub 1-0:1.0: cannot reset port 1 (err = -32) hub 1-0:1.0: cannot reset port 1 (err = -32) hub 1-0:1.0: cannot reset port 1 (err = -32) hub 1-0:1.0: Cannot enable port 1. Maybe the USB cable is bad? hub 1-0:1.0: unable to enumerate USB device on port 1 Fixes: the issue existed when the otg fsm code was added. Signed-off-by: Peter Chen <peter.chen@freescale.com> Signed-off-by: Felipe Balbi <balbi@ti.com> [lizf: Backported to 3.4: - adjust filename - adjust context] Signed-off-by: Zefan Li <lizefan@huawei.com>
-
Alex Deucher authored
commit fd99a094 upstream. Use the correct flags for atom. v2: handle DRM_MODE_FLAG_DBLCLK Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Zefan Li <lizefan@huawei.com>
-
Baruch Siach authored
commit 838d030b upstream. The callback function signature has changed in commit a5818a8b (pinctrl: get_group_pins() const fixes) Fixes: a5818a8b ('pinctrl: get_group_pins() const fixes') Cc: Stephen Warren <swarren@nvidia.com> Signed-off-by: Baruch Siach <baruch@tkos.co.il> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Zefan Li <lizefan@huawei.com>
-
Baruch Siach authored
commit b18104c0 upstream. This API has changed in commit 6e5e959d (pinctrl: API changes to support multiple states per device). Fixes: 6e5e959d ('pinctrl: API changes to support multiple states per device') Cc: Stephen Warren <swarren@nvidia.com> Signed-off-by: Baruch Siach <baruch@tkos.co.il> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Zefan Li <lizefan@huawei.com>
-
Krzysztof Kozlowski authored
commit 1915a718 upstream. The return value of power_supply_register() call was not checked and even on error probe() function returned 0. If registering failed then during unbind the driver tried to unregister power supply which was not actually registered. This could lead to memory corruption because power_supply_unregister() unconditionally cleans up given power supply. Fix this by checking return status of power_supply_register() call. In case of failure, clean up sysfs entries and fail the probe. Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com> Fixes: 9be0fcb5 ("compal-laptop: add JHL90, battery & hwmon interface") Signed-off-by: Sebastian Reichel <sre@kernel.org> [lizf: Backported to 3.4: there's no "remove" label. Do cleanup inside if block] Signed-off-by: Zefan Li <lizefan@huawei.com>
-
Baruch Siach authored
commit 939417bd upstream. struct pinctrl_desc does not contain the maxpin member since commit 0d2006bb (pinctrl: remove unnecessary max pin number). Fixes: 0d2006bb ('pinctrl: remove unnecessary max pin number') Signed-off-by: Baruch Siach <baruch@tkos.co.il> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Zefan Li <lizefan@huawei.com>
-
Felipe Balbi authored
commit e3c93e1a upstream. As per Mentor Graphics' documentation, we should always handle TX endpoints before RX endpoints. This patch fixes that error while also updating some hard-to-read comments which were scattered around musb_interrupt(). This patch should be backported as far back as possible since this error has been in the driver since it's conception. Signed-off-by: Felipe Balbi <balbi@ti.com> [lizf: Backported to 3.4: adjust context] Signed-off-by: Zefan Li <lizefan@huawei.com>
-
Ekaterina Tumanova authored
commit b75f4c9a upstream. s390 documentation requires words 0 and 10-15 to be reserved and stored as zeros. As we fill out all other fields, we can memset the full structure. Signed-off-by: Ekaterina Tumanova <tumanova@linux.vnet.ibm.com> Reviewed-by: David Hildenbrand <dahi@linux.vnet.ibm.com> Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com> Signed-off-by: Zefan Li <lizefan@huawei.com>
-
Sabrina Dubroca authored
commit 08e83316 upstream. There is a race condition between e1000_change_mtu's cleanups and netpoll, when we change the MTU across jumbo size: Changing MTU frees all the rx buffers: e1000_change_mtu -> e1000_down -> e1000_clean_all_rx_rings -> e1000_clean_rx_ring Then, close to the end of e1000_change_mtu: pr_info -> ... -> netpoll_poll_dev -> e1000_clean -> e1000_clean_rx_irq -> e1000_alloc_rx_buffers -> e1000_alloc_frag And when we come back to do the rest of the MTU change: e1000_up -> e1000_configure -> e1000_configure_rx -> e1000_alloc_jumbo_rx_buffers alloc_jumbo finds the buffers already != NULL, since data (shared with page in e1000_rx_buffer->rxbuf) has been re-alloc'd, but it's garbage, or at least not what is expected when in jumbo state. This results in an unusable adapter (packets don't get through), and a NULL pointer dereference on the next call to e1000_clean_rx_ring (other mtu change, link down, shutdown): BUG: unable to handle kernel NULL pointer dereference at (null) IP: [<ffffffff81194d6e>] put_compound_page+0x7e/0x330 [...] Call Trace: [<ffffffff81195445>] put_page+0x55/0x60 [<ffffffff815d9f44>] e1000_clean_rx_ring+0x134/0x200 [<ffffffff815da055>] e1000_clean_all_rx_rings+0x45/0x60 [<ffffffff815df5e0>] e1000_down+0x1c0/0x1d0 [<ffffffff811e2260>] ? deactivate_slab+0x7f0/0x840 [<ffffffff815e21bc>] e1000_change_mtu+0xdc/0x170 [<ffffffff81647050>] dev_set_mtu+0xa0/0x140 [<ffffffff81664218>] do_setlink+0x218/0xac0 [<ffffffff814459e9>] ? nla_parse+0xb9/0x120 [<ffffffff816652d0>] rtnl_newlink+0x6d0/0x890 [<ffffffff8104f000>] ? kvm_clock_read+0x20/0x40 [<ffffffff810a2068>] ? sched_clock_cpu+0xa8/0x100 [<ffffffff81663802>] rtnetlink_rcv_msg+0x92/0x260 By setting the allocator to a dummy version, netpoll can't mess up our rx buffers. The allocator is set back to a sane value in e1000_configure_rx. Fixes: edbbb3ca ("e1000: implement jumbo receive with partial descriptors") Signed-off-by: Sabrina Dubroca <sd@queasysnail.net> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: Zefan Li <lizefan@huawei.com>
-
K. Y. Srinivasan authored
commit 40384e4b upstream. Correctly rollback state if the failure occurs after we have handed over the ownership of the buffer to the host. Signed-off-by: K. Y. Srinivasan <kys@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Zefan Li <lizefan@huawei.com>
-
Alexander Ploumistos authored
commit 2eeff0b4 upstream. Add 04f2:aff1 to ath3k.c supported devices list and btusb.c blacklist, so that the device can load the ath3k firmware and re-enumerate itself as an AR3011 device. T: Bus=05 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 2 Spd=12 MxCh= 0 D: Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=04f2 ProdID=aff1 Rev= 0.01 C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=1ms E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms Signed-off-by: Alexander Ploumistos <alexpl@fedoraproject.org> Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Zefan Li <lizefan@huawei.com>
-
- 14 Sep, 2015 1 commit
-
-
Weilong Chen authored
There's a check for ip6_null_entry, but it's not enough if the config CONFIG_IPV6_MULTIPLE_TABLES is selected. Blackhole or prohibited entries should also be ignored. This path is for kernel before v3.6, as there's a commit b94f1c09 use icmpv6_notify() instead of rt6_redirect() and rt6_redirect has been deleted. The oops as follow: [exception RIP: do_raw_write_lock+12] RIP: ffffffff8122c42c RSP: ffff880666e45820 RFLAGS: 00010282 RAX: ffff8801207bffd8 RBX: 0000000000000018 RCX: 0000000000000000 RDX: 0000000000000000 RSI: ffff880666e45898 RDI: 0000000000000018 RBP: ffff880666e45830 R8: 000000000000001e R9: 0000000006000000 R10: ffff88011796b8a0 R11: 0000000000000004 R12: ffff88010391ed00 R13: 0000000000000000 R14: ffff880666e45898 R15: ffff88011796b890 ORIG_RAX: ffffffffffffffff CS: 0010 SS: 0018 [ffff880666e45838] _raw_write_lock_bh at ffffffff81450b39 [ffff880666e45858] __ip6_ins_rt at ffffffff813ed8c1 [ffff880666e45888] ip6_ins_rt at ffffffff813eef58 [ffff880666e458b8] rt6_redirect at ffffffff813f0b84 [ffff880666e45958] ndisc_rcv at ffffffff813f95d8 [ffff880666e45a08] icmpv6_rcv at ffffffff814000e8 [ffff880666e45ae8] ip6_input_finish at ffffffff813e43bb [ffff880666e45b38] ip6_input at ffffffff813e4b08 [ffff880666e45b68] ipv6_rcv at ffffffff813e4969 [ffff880666e45bc8] __netif_receive_skb at ffffffff8135158a [ffff880666e45c38] dev_gro_receive at ffffffff81351cb0 [ffff880666e45c78] napi_gro_receive at ffffffff81351fc5 [ffff880666e45cb8] tg3_rx at ffffffffa0bfb354 [tg] [ffff880666e45d88] tg3_poll_work at ffffffffa0c07857 [tg] [ffff880666e45e18] tg3_poll_msix at ffffffffa0c07d1b [tg] [ffff880666e45e68] net_rx_action at ffffffff81352219 [ffff880666e45ec8] __do_softirq at ffffffff8103e5a1 [ffff880666e45f38] call_softirq at ffffffff81459c4c [ffff880666e45f50] do_softirq at ffffffff8100413d [ffff880666e45f80] do_IRQ at ffffffff81003cce This happened when ip6_route_redirect found a rt which was set blackhole, the rt had a NULL rt6i_table argument which is accessed by __ip6_ins_rt() when trying to lock rt6i_table->tb6_lock caused a BUG: "BUG: unable to handle kernel NULL pointer" Signed-off-by: Weilong Chen <chenweilong@huawei.com>
-
- 19 Jun, 2015 7 commits
-
-
Zefan Li authored
-
Ian Campbell authored
commit 31a41898 upstream. When we come to tear things down in netback_remove() and generate the uevent it is possible that the xenstore directory has already been removed (details below). In such cases netback_uevent() won't be able to read the hotplug script and will write a xenstore error node. A recent change to the hypervisor exposed this race such that we now sometimes lose it (where apparently we didn't ever before). Instead read the hotplug script configuration during setup and use it for the lifetime of the backend device. The apparently more obvious fix of moving the transition to state=Closed in netback_remove() to after the uevent does not work because it is possible that we are already in state=Closed (in reaction to the guest having disconnected as it shutdown). Being already in Closed means the toolstack is at liberty to start tearing down the xenstore directories. In principal it might be possible to arrange to unregister the device sooner (e.g on transition to Closing) such that xenstore would still be there but this state machine is fragile and prone to anger... A modern Xen system only relies on the hotplug uevent for driver domains, when the backend is in the same domain as the toolstack it will run the necessary setup/teardown directly in the correct sequence wrt xenstore changes. Signed-off-by: Ian Campbell <ian.campbell@citrix.com> Acked-by: Wei Liu <wei.liu2@citrix.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Zefan Li <lizefan@huawei.com>
-
Joonsoo Kim authored
commit 43d77867 upstream. Current implementation of unfreeze_partials() is so complicated, but benefit from it is insignificant. In addition many code in do {} while loop have a bad influence to a fail rate of cmpxchg_double_slab. Under current implementation which test status of cpu partial slab and acquire list_lock in do {} while loop, we don't need to acquire a list_lock and gain a little benefit when front of the cpu partial slab is to be discarded, but this is a rare case. In case that add_partial is performed and cmpxchg_double_slab is failed, remove_partial should be called case by case. I think that these are disadvantages of current implementation, so I do refactoring unfreeze_partials(). Minimizing code in do {} while loop introduce a reduced fail rate of cmpxchg_double_slab. Below is output of 'slabinfo -r kmalloc-256' when './perf stat -r 33 hackbench 50 process 4000 > /dev/null' is done. ** before ** Cmpxchg_double Looping ------------------------ Locked Cmpxchg Double redos 182685 Unlocked Cmpxchg Double redos 0 ** after ** Cmpxchg_double Looping ------------------------ Locked Cmpxchg Double redos 177995 Unlocked Cmpxchg Double redos 1 We can see cmpxchg_double_slab fail rate is improved slightly. Bolow is output of './perf stat -r 30 hackbench 50 process 4000 > /dev/null'. ** before ** Performance counter stats for './hackbench 50 process 4000' (30 runs): 108517.190463 task-clock # 7.926 CPUs utilized ( +- 0.24% ) 2,919,550 context-switches # 0.027 M/sec ( +- 3.07% ) 100,774 CPU-migrations # 0.929 K/sec ( +- 4.72% ) 124,201 page-faults # 0.001 M/sec ( +- 0.15% ) 401,500,234,387 cycles # 3.700 GHz ( +- 0.24% ) <not supported> stalled-cycles-frontend <not supported> stalled-cycles-backend 250,576,913,354 instructions # 0.62 insns per cycle ( +- 0.13% ) 45,934,956,860 branches # 423.297 M/sec ( +- 0.14% ) 188,219,787 branch-misses # 0.41% of all branches ( +- 0.56% ) 13.691837307 seconds time elapsed ( +- 0.24% ) ** after ** Performance counter stats for './hackbench 50 process 4000' (30 runs): 107784.479767 task-clock # 7.928 CPUs utilized ( +- 0.22% ) 2,834,781 context-switches # 0.026 M/sec ( +- 2.33% ) 93,083 CPU-migrations # 0.864 K/sec ( +- 3.45% ) 123,967 page-faults # 0.001 M/sec ( +- 0.15% ) 398,781,421,836 cycles # 3.700 GHz ( +- 0.22% ) <not supported> stalled-cycles-frontend <not supported> stalled-cycles-backend 250,189,160,419 instructions # 0.63 insns per cycle ( +- 0.09% ) 45,855,370,128 branches # 425.436 M/sec ( +- 0.10% ) 169,881,248 branch-misses # 0.37% of all branches ( +- 0.43% ) 13.596272341 seconds time elapsed ( +- 0.22% ) No regression is found, but rather we can see slightly better result. Acked-by: Christoph Lameter <cl@linux.com> Signed-off-by: Joonsoo Kim <js1304@gmail.com> Signed-off-by: Pekka Enberg <penberg@kernel.org> [lizf: Backported to 3.4: adjust context] Signed-off-by: Zefan Li <lizefan@huawei.com>
-
Ben Hutchings authored
commit 8014bcc8 upstream. The variable for the 'permissive' module parameter used to be static but was recently changed to be extern. This puts it in the kernel global namespace if the driver is built-in, so its name should begin with a prefix identifying the driver. Signed-off-by: Ben Hutchings <ben@decadent.org.uk> Fixes: af6fc858 ("xen-pciback: limit guest control of command register") Signed-off-by: David Vrabel <david.vrabel@citrix.com> Signed-off-by: Zefan Li <lizefan@huawei.com>
-
Tejun Heo authored
commit 464d1387 upstream. mm/page-writeback.c has several places where 1 is added to the divisor to prevent division by zero exceptions; however, if the original divisor is equivalent to -1, adding 1 leads to division by zero. There are three places where +1 is used for this purpose - one in pos_ratio_polynom() and two in bdi_position_ratio(). The second one in bdi_position_ratio() actually triggered div-by-zero oops on a machine running a 3.10 kernel. The divisor is x_intercept - bdi_setpoint + 1 == span + 1 span is confirmed to be (u32)-1. It isn't clear how it ended up that but it could be from write bandwidth calculation underflow fixed by c72efb65 ("writeback: fix possible underflow in write bandwidth calculation"). At any rate, +1 isn't a proper protection against div-by-zero. This patch converts all +1 protections to |1. Note that bdi_update_dirty_ratelimit() was already using |1 before this patch. Signed-off-by: Tejun Heo <tj@kernel.org> Reviewed-by: Jan Kara <jack@suse.cz> Signed-off-by: Jens Axboe <axboe@fb.com> [lizf: Backported to 3.4: drop other two changes as there's only one such statment in 3.4] Signed-off-by: Zefan Li <lizefan@huawei.com>
-
Yann Droneaud authored
commit 66578b0b upstream. In a call to ib_umem_get(), if address is 0x0 and size is already page aligned, check added in commit 8494057a ("IB/uverbs: Prevent integer overflow in ib_umem_get address arithmetic") will refuse to register a memory region that could otherwise be valid (provided vm.mmap_min_addr sysctl and mmap_low_allowed SELinux knobs allow userspace to map something at address 0x0). This patch allows back such registration: ib_umem_get() should probably don't care of the base address provided it can be pinned with get_user_pages(). There's two possible overflows, in (addr + size) and in PAGE_ALIGN(addr + size), this patch keep ensuring none of them happen while allowing to pin memory at address 0x0. Anyway, the case of size equal 0 is no more (partially) handled as 0-length memory region are disallowed by an earlier check. Link: http://mid.gmane.org/cover.1428929103.git.ydroneaud@opteya.com Cc: Shachar Raindel <raindel@mellanox.com> Cc: Jack Morgenstein <jackm@mellanox.com> Cc: Or Gerlitz <ogerlitz@mellanox.com> Signed-off-by: Yann Droneaud <ydroneaud@opteya.com> Reviewed-by: Sagi Grimberg <sagig@mellanox.com> Reviewed-by: Haggai Eran <haggaie@mellanox.com> Signed-off-by: Doug Ledford <dledford@redhat.com> Signed-off-by: Zefan Li <lizefan@huawei.com>
-
Quentin Casasnovas authored
commit 0d3bba02 upstream. Phil and I found out a problem with commit: 7e860a6e ("cdc-acm: add sanity checks") It added some sanity checks to ignore potential garbage in CDC headers but also introduced a potential infinite loop. This can happen at the first loop iteration (elength = 0 in that case) if the description isn't a DT_CS_INTERFACE or later if 'buffer[0]' is zero. It should also be noted that the wrong length was being added to 'buffer' in case 'buffer[1]' was not a DT_CS_INTERFACE descriptor, since elength was assigned after that check in the loop. A specially crafted USB device could be used to trigger this infinite loop. Fixes: 7e860a6e ("cdc-acm: add sanity checks") Signed-off-by: Phil Turnbull <phil.turnbull@oracle.com> Signed-off-by: Quentin Casasnovas <quentin.casasnovas@oracle.com> CC: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com> CC: Oliver Neukum <oneukum@suse.de> CC: Adam Lee <adam8157@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Zefan Li <lizefan@huawei.com>
-