- 22 Jul, 2011 16 commits
-
-
Don Skidmore authored
Private rx_csum flags are now duplicate of netdev->features & NETIF_F_RXCSUM. We remove those duplicates and now use the net_device_ops ndo_set_features. This was based on the original patch submitted by Michal Miroslaw <mirq-linux@rere.qmqm.pl>. I also removed the special case not requiring a reset for X540 hardware. It is needed just as it is in 82599 hardware. Signed-off-by:
Don Skidmore <donald.c.skidmore@intel.com> Cc: Michal Miroslaw <mirq-linux@rere.qmqm.pl> Tested-by:
Phil Schmitt <phillip.j.schmitt@intel.com> Signed-off-by:
Jeff Kirsher <jeffrey.t.kirsher@intel.com>
-
Andy Gospodarek authored
Martin Wilck <martin.wilck@ts.fujitsu.com> reported that systems using the ixgbe-driver that were capable of WoL were rebooting almost as soon as they were shut down. This is because the default WoL settings enabled magic packet, broadcast, unicast, and multicast. Other Intel devices seem to use the stored eeprom value for initial WoL capabilities. The 82578DM (e1000e) and 82576 (igb) the devices I looked at had only the magic packet enabled in the eeprom, so that seems appropriate on ixgbe-based devices as well. I set the WoL options on my 82578DM to be the same default as the ixgbe devices (umbg) and saw the same as Martin -- almost as soon as my box shutdown, it booted again. This patch changes the default to only be the magic packet. This is the same as the default for most Intel and non-Intel hardware currently upstream. Signed-off-by:
Andy Gospodarek <andy@greyhouse.net> CC: Martin Wilck <martin.wilck@ts.fujitsu.com> Tested-by:
-
Emil Tantilov authored
Signed-off-by:
Emil Tantilov <emil.s.tantilov@intel.com> Tested-by:
-
Alexander Duyck authored
This change is meant to address possible race conditions from the status and error bits on the RX descriptors being re-read by multiple functions in the RX cleanup path. To resolve this I have added code that will pass the staterr value to those functions. Signed-off-by:
Alexander Duyck <alexander.h.duyck@intel.com> Tested-by:
Ross Brattain <ross.b.brattain@intel.com> Signed-off-by:
-
Alexander Duyck authored
This change moves work_limit, total_packets, and total_bytes into the ring container struct of the q_vector. The advantage of this is that it should reduce the size of memory used in the event of multiple rings being assigned to a single q_vector. In addition it should help to reduce the total workload for calculating itr since now total_packets and total_bytes will be the total work done of the interrupt instead of for the ring. Signed-off-by:
-
Alexander Duyck authored
This patch adds support for a ring container structure to be used within the q_vector. The basic idea is to provide a means of separating the RX and TX rings while maintaining a common structure for their containment. The advantage to this is that later we should be able to pass this structure to the update_itr functions without needing to pass individual rings. Signed-off-by:
-
Alexander Duyck authored
The ixgbe_maybe_stop_tx function is only a few lines long and is called multiple times through the xmit hotpath. In order to streamline things it makes sense to just inline it. Signed-off-by:
-
Alexander Duyck authored
This change is meant to update ATR so that it will use the recorded RX queue instead of the CPU in the case of routing. This change is meant to help ixgbe default behavior to more closely match that of the kernel. Signed-off-by:
-
Robert Healy authored
On this chipset it is required to configure the MPHY block for loopback tests. If MPHY is not configured then all loopback tests will report failures. Signed-off-by:
Robert Healy <robert.healy@intel.com> Tested-by:
Aaron Brown <aaron.f.brown@intel.com> Signed-off-by:
-
Nicolas Schichan authored
Interrupts about link lost or rx sequence errors are not reported by the ce4100 hardware, leading to transitions from link UP to link DOWN never being reported. Signed-off-by:
Nicolas Schichan <nschichan@freebox.fr> Tested-by:
-
Thadeu Lima de Souza Cascardo authored
The function can_get_bittiming is not used anywhere else, so it should be static. Signed-off-by:
Thadeu Lima de Souza Cascardo <cascardo@holoscopio.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Choi, Jong-Hwan authored
Kobj and queues_kset are used with CONFIG_XPS=y. Signed-off-by:
Choi, Jong-Hwan <jhbird.choi@samsung.com> Signed-off-by:
-
Shreyas Bhatewara authored
NETIF_F_HIGHDMA is being disabled even when dma64 is true. This patch fixes it. CC: Michal Miroslaw <mirq-linux@rere.qmqm.pl> Signed-off-by:
Shreyas N Bhatewara <sbhatewara@vmware.com> Signed-off-by:
-
Shreyas Bhatewara authored
Parent device for netdev should be set before netdev_info() can be called otherwise there is a NULL pointer dereference and probe() fails. Signed-off-by:
-
Marek Vasut authored
This device can be found in Acer Iconia TAB W500 tablet dock. Signed-off-by:
Marek Vasut <marek.vasut@gmail.com> Signed-off-by:
-
David S. Miller authored
-
- 21 Jul, 2011 24 commits
-
-
Giuseppe CAVALLARO authored
This patch adds new information for the driver especially about its platform structure fields. Signed-off-by:
Giuseppe Cavallaro <peppe.cavallaro@st.com> Signed-off-by:
-
Giuseppe CAVALLARO authored
Prior to this change, most PHY configuration parameters were passed into the STMMAC device as a separate PHY device. As well as being unusual, this made it difficult to make changes to the MAC/PHY relationship. This patch moves all the PHY parameters into the MAC configuration structure, mainly as a separate structure. This allows us to completely ignore the MDIO bus attached to a stmmac if desired, and not create the PHY bus. It also allows the stmmac driver to use a different PHY from the one it is connected to, for example a fixed PHY or bit banging PHY. Also derive the stmmac/PHY connection type (MII/RMII etc) from the mode can be passed into <platf>_configure_ethernet. STLinux kernel at git://git.stlinux.com/stm/linux-sh4-2.6.32.y.git provides several examples how to use this new infrastructure (that actually is easier to maintain and clearer). Signed-off-by:
Stuart Menefy <stuart.menefy@st.com> Signed-off-by:
-
Giuseppe CAVALLARO authored
The patch removes the following serie of warnings when the driver is compiled as built-in: drivers/net/stmmac/stmmac_main.c: In function stmmac_cmdline_opt: drivers/net/stmmac/stmmac_main.c:1855:12: warning: ignoring return value of kstrtoul, declared with attribute warn_unused_result [snip] Signed-off-by:
-
Giuseppe CAVALLARO authored
Signed-off-by:
-
Ben Hutchings authored
Some drivers (ab)use the ethtool_ops::get_regs operation to expose only a hardware revision ID. Commit a77f5db3 ('ethtool: Allocate register dump buffer with vmalloc()') had the side-effect of breaking these, as vmalloc() returns a null pointer for size=0 whereas kmalloc() did not. For backward-compatibility, allow zero-length dumps again. Reported-by:
Kalle Valo <kvalo@qca.qualcomm.com> Signed-off-by:
Ben Hutchings <bhutchings@solarflare.com> Cc: stable@kernel.org [2.6.37+] Signed-off-by:
-
Guo-Fu Tseng authored
This patch add the missing dma_unmap(). Which solved the critical issue of system freeze on heavy load. Michal Miroslaw's rejected patch: [PATCH v2 10/46] net: jme: convert to generic DMA API Pointed out the issue also, thank you Michal. But the fix was incorrect. It would unmap needed address when low memory. Got lots of feedback from End user and Gentoo Bugzilla. https://bugs.gentoo.org/show_bug.cgi?id=373109 Thank you all. :) Cc: stable@kernel.org Signed-off-by:
Guo-Fu Tseng <cooldavid@cooldavid.org> Acked-by:
Chris Wright <chrisw@sous-sol.org> Signed-off-by:
-
Dan Carpenter authored
There are two problems: 1) "n" was allocated with alloc_skb() so we should free it with kfree_skb() instead of regular kfree(). 2) We return the freed pointer instead of NULL. Signed-off-by:
Dan Carpenter <error27@gmail.com> Reviewed-by:
Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by:
-
Jiri Pirko authored
there are no users outside vlan code Signed-off-by:
Jiri Pirko <jpirko@redhat.com> Signed-off-by:
-
Jiri Pirko authored
has no users so remove it Signed-off-by:
-
Jiri Pirko authored
ndo_vlan_rx_register is no longer in use in any driver so remove it. Signed-off-by:
-
Jiri Pirko authored
Now when all devices are cleaned up, bond can be cleaned up as well - remove bond->vlgrp - remove bond_vlan_rx_register - substitute necessary occurences of vlan_group_get_device Signed-off-by:
-
Jiri Pirko authored
Signed-off-by:
-
Jiri Pirko authored
Signed-off-by:
-
Jiri Pirko authored
- kill priv->vlgrp and stmmac_vlan_rx_register (used for nothing :)) Signed-off-by:
-
Jiri Pirko authored
Signed-off-by:
-
Jiri Pirko authored
- unify vlan and nonvlan rx path - kill card->vlangrp and qeth_l3_vlan_rx_register Signed-off-by:
-
Jiri Pirko authored
- unify vlan and nonvlan rx path - kill vdev->vlgrp and vxge_vlan_rx_register Signed-off-by:
-
Jiri Pirko authored
- unify vlan and nonvlan rx path - kill adapter->vlgrp and igb_vlan_rx_register - allow to turn on/off rx/tx vlan accel via ethtool (set_features) Signed-off-by:
-
Jiri Pirko authored
- unify vlan and nonvlan rx path - kill np->vlangrp and nv_vlan_rx_register - allow to turn on/off rx vlan accel via ethtool (set_features) Signed-off-by:
-
Jiri Pirko authored
- unify vlan and nonvlan rx path - kill adapter->vlgrp and e1000_vlan_rx_register - allow to turn on/off rx/tx vlan accel via ethtool (set_features) Signed-off-by:
-
Jiri Pirko authored
Signed-off-by:
-
Jiri Pirko authored
- unify vlan and nonvlan rx path - kill pi->vlan_grp and vlan_rx_register - allow to turn on/off rx/tx vlan accel via ethtool (set_features) Signed-off-by:
-
Jiri Pirko authored
- unify vlan and nonvlan rx path - kill adapter->vlgrp and atl2_vlan_rx_register - allow to turn on/off rx/tx vlan accel via ethtool (set_features) Signed-off-by:
-
Jiri Pirko authored
- unify vlan and nonvlan rx path - kill adapter->vlgrp and atlx_vlan_rx_register - allow to turn on/off rx/tx vlan accel via ethtool (set_features) Signed-off-by:
-
