- 17 Oct, 2012 11 commits
-
-
Russ Gorby authored
commit 5e44708f upstream. There were some locking holes in the management of the MUX's message queue for 2 code paths: 1) gsmld_write_wakeup 2) receipt of CMD_FCON flow-control message In both cases gsm_data_kick is called w/o locking so it can collide with other other instances of gsm_data_kick (pulling messages tx_tail) or potentially other instances of __gsm_data_queu (adding messages to tx_head) Changed to take the tx_lock in these 2 cases Signed-off-by:
Russ Gorby <russ.gorby@intel.com> Tested-by:
Yin, Fengwei <fengwei.yin@intel.com> Signed-off-by:
Alan Cox <alan@linux.intel.com> Signed-off-by:
Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by:
Ben Hutchings <ben@decadent.org.uk>
-
samix.lebsir authored
commit 10c6c383 upstream. The design of uplink flow control in the mux driver is that for constipated channels data will backup into the per-channel fifos, and any messages that make it to the outbound message queue will still go out. Code was added to also stop messages that were in the outbound queue but this requires filtering through all the messages on the queue for stopped dlcis and changes some of the mux logic unneccessarily. The message fiiltering was removed to be in line w/ the original design as the message filtering does not provide any solution. Extra debug messages used during investigation were also removed. Signed-off-by:
samix.lebsir <samix.lebsir@intel.com> Signed-off-by:
-
Frederic Berat authored
commit c01af4fe upstream. - Correcting handling of FCon/FCoff in order to respect 27.010 spec - Consider FCon/off will overide all dlci flow control except for dlci0 as we must be able to send control frames. - Dlci constipated handling according to FC, RTC and RTR values. - Modifying gsm_dlci_data_kick and gsm_dlci_data_sweep according to dlci constipated value Signed-off-by:
Frederic Berat <fredericx.berat@intel.com> Signed-off-by:
-
Russ Gorby authored
commit 192b6041 upstream. gsm_dlci_data_kick will not call any output function if tx_bytes > THRESH_LO furthermore it will call the output function only once if tx_bytes == 0 If the size of the IP writes are on the order of THRESH_LO we can get into a situation where skbs accumulate on the outbound list being starved for events to call the output function. gsm_dlci_data_kick now calls the sweep function when tx_bytes==0 Signed-off-by:
Kappel, LaurentX <laurentx.kappel@intel.com> Signed-off-by:
-
xiaojin authored
commit 7e8ac7b2 upstream. In 3GPP27.010 5.8.1, it defined: The TE multiplexer initiates the establishment of the multiplexer control channel by sending a SABM frame on DLCI 0 using the procedures of clause 5.4.1. Once the multiplexer channel is established other DLCs may be established using the procedures of clause 5.4.1. This patch implement 5.8.1 in MUX level, it make sure DLC0 is the first channel to be setup. [or for those not familiar with the specification: it was possible to try and open a data connection while the control channel was not yet fully open, which is a spec violation and confuses some modems] Signed-off-by:
xiaojin <jin.xiao@intel.com> Tested-by:
-
Stanislav Kozina authored
commit e9490e93 upstream. Change the BUG_ON to WARN_ON and return in case of tty->read_buf==NULL. We want to track a couple of long standing reports of this but at the same time we can avoid killing the box. Signed-off-by:
Stanislav Kozina <skozina@redhat.com> Signed-off-by:
-
Jiri Slaby authored
commit ee8b593a upstream. If a user provides a buffer larger than a tty->write_buf chunk and passes '\r' at the end of the buffer, we touch an out-of-bound memory. Add a check there to prevent this. Signed-off-by:
Jiri Slaby <jslaby@suse.cz> Cc: Samo Pogacnik <samo_pogacnik@t-2.net> Signed-off-by:
-
Tejun Heo authored
commit 959d1af8 upstream. WORK_STRUCT_PENDING is used to claim ownership of a work item and process_one_work() releases it before starting execution. When someone else grabs PENDING, all pre-release updates to the work item should be visible and all updates made by the new owner should happen afterwards. Grabbing PENDING uses test_and_set_bit() and thus has a full barrier; however, clearing doesn't have a matching wmb. Given the preceding spin_unlock and use of clear_bit, I don't believe this can be a problem on an actual machine and there hasn't been any related report but it still is theretically possible for clear_pending to permeate upwards and happen before work->entry update. Add an explicit smp_wmb() before work_clear_pending(). Signed-off-by:
Tejun Heo <tj@kernel.org> Cc: Oleg Nesterov <oleg@redhat.com> Signed-off-by:
-
Eugeni Dodonov authored
commit ab3951eb upstream. We should not hit this under any sane conditions, but still, this does not looks right. CC: Chris Wilson <chris@chris-wilson.co.uk> CC: Daniel Vetter <daniel.vetter@ffwll.ch> Reported-by:
Herton Ronaldo Krzesinski <herton.krzesinski@canonical.com> Reviewed-by:
Chris Wlison <chris@chris-wilson.co.uk> Signed-off-by:
Eugeni Dodonov <eugeni.dodonov@intel.com> Signed-off-by:
Daniel Vetter <daniel.vetter@ffwll.ch> Signed-off-by:
-
Shmulik Ladkani authored
commit 7bb9c754 upstream. The code responsible for reading the version of the mirror bbt was incorrectly using the descriptor of the main bbt. Pass the mirror bbt descriptor to 'scan_read_raw' when reading the version of the mirror bbt. Signed-off-by:
Shmulik Ladkani <shmulik.ladkani@gmail.com> Acked-by:
Sebastian Andrzej Siewior <bigeasy@linutronix.de> Signed-off-by:
Artem Bityutskiy <artem.bityutskiy@linux.intel.com> Signed-off-by:
David Woodhouse <David.Woodhouse@intel.com> Signed-off-by:
-
Dan Williams authored
commit 6d70a74f upstream. The oem parameter image embedded in the efi variable is at an offset from the start of the variable. However, in the failure path we try to free the 'orom' pointer which is only valid when the paramaters are being read from the legacy option-rom space. Since failure to load the oem parameters is unlikely and we keep the memory around in the success case just defer all de-allocation to devm. Reported-by:
Don Morris <don.morris@hp.com> Signed-off-by:
Dan Williams <dan.j.williams@intel.com> Signed-off-by:
-
- 10 Oct, 2012 29 commits
-
-
Ben Hutchings authored
-
Yevgeniy Melnichuk authored
commit bc21fde2 upstream. Add Sony Vaio T-Series Bluetooth Module( 0x489:0xE036) to the blacklist of btusb module and add it to the ath3k module. output of cat /sys/kernel/debug/usb/devices T: Bus=01 Lev=02 Prnt=02 Port=01 Cnt=01 Dev#= 5 Spd=12 MxCh= 0 D: Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=0489 ProdID=e036 Rev= 0.02 S: Manufacturer=Atheros Communications S: Product=Bluetooth USB Host Controller S: SerialNumber=Alaska Day 2006 C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=1ms E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms Signed-off-by:
Yevgeniy Melnichuk <yevgeniy.melnichuk@googlemail.com> Signed-off-by:
Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com> Acked-by:
Marcel Holtmann <marcel@holtmann.org> Signed-off-by:
Gustavo Padovan <gustavo.padovan@collabora.co.uk> Signed-off-by:
-
Peng Chen authored
commit 2096ae6c upstream. Add support for the AR3012 chip found on Fioxconn. usb-devices shows: T: Bus=06 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 44 Spd=12 MxCh= 0 D: Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=0489 ProdID=e057 Rev= 0.02 C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=1ms E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms Signed-off-by:
Peng Chen <pengchen@qca.qualcomm.com> Signed-off-by:
-
Giancarlo Formicuccia authored
commit 6c4ae5c2 upstream. Add support for the AR3012 chip found on the Toshiba Sallite M840-1000-XQ. usb-devices shows: T: Bus=01 Lev=02 Prnt=02 Port=02 Cnt=01 Dev#= 5 Spd=12 MxCh= 0 D: Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=0930 ProdID=0219 Rev=00.02 S: Manufacturer=Atheros Communications S: Product=Bluetooth USB Host Controller S: SerialNumber=Alaska Day 2006 C: #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA I: If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb I: If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb Signed-off-by:
Giancarlo Formicuccia <giancarlo.formicuccia@gmail.com> Signed-off-by:
-
Marek Vasut authored
commit 6eda541d upstream. Acer used this chip connected via USB: Bus 005 Device 005: ID 0cf3:3005 Atheros Communications, Inc. AR3011 Bluetooth Device Descriptor: bLength 18 bDescriptorType 1 bcdUSB 1.10 bDeviceClass 224 Wireless bDeviceSubClass 1 Radio Frequency bDeviceProtocol 1 Bluetooth bMaxPacketSize0 64 idVendor 0x0cf3 Atheros Communications, Inc. idProduct 0x3005 AR3011 Bluetooth bcdDevice 0.01 iManufacturer 0 iProduct 0 iSerial 0 bNumConfigurations 1 Signed-off-by:
Marek Vasut <marex@denx.de> Cc: Gustavo Padovan <gustavo@padovan.org> Cc: Johan Hedberg <johan.hedberg@gmail.com> Cc: Marcel Holtmann <marcel@holtmann.org> Signed-off-by:
-
Matt Carlson authored
[ Upstream commit cf9ecf4b ] On the earliest TSO capable devices, TSO was accomplished through firmware. The TSO cannot coexist with ASF management firmware though. The tg3 driver determines whether or not ASF is enabled by calling tg3_get_eeprom_hw_cfg(), which checks a particular bit of NIC memory. Commit dabc5c67, entitled "tg3: Move TSO_CAPABLE assignment", accidentally moved the code that determines TSO capabilities earlier than the call to tg3_get_eeprom_hw_cfg(). As a consequence, the driver was attempting to determine TSO capabilities before it had all the data it needed to make the decision. This patch fixes the problem by revisiting and reevaluating the decision after tg3_get_eeprom_hw_cfg() is called. Signed-off-by:
Matt Carlson <mcarlson@broadcom.com> Signed-off-by:
Michael Chan <mchan@broadcom.com> Signed-off-by:
David S. Miller <davem@davemloft.net> Signed-off-by:
-
Ed Cashin authored
[ Upstream commit 8babe8cc ] In order for the network layer to see that AoE requires no checksumming in a generic way, the packets must be marked as requiring no checksum, so we make this requirement explicit with the assertion. Signed-off-by:
Ed Cashin <ecashin@coraid.com> Signed-off-by:
-
Ed Cashin authored
[ Upstream commit c0d680e5 ] A change in a series of VLAN-related changes appears to have inadvertently disabled the use of the scatter gather feature of network cards for transmission of non-IP ethernet protocols like ATA over Ethernet (AoE). Below is a reference to the commit that introduces a "harmonize_features" function that turns off scatter gather when the NIC does not support hardware checksumming for the ethernet protocol of an sk buff. commit f01a5236 Author: Jesse Gross <jesse@nicira.com> Date: Sun Jan 9 06:23:31 2011 +0000 net offloading: Generalize netif_get_vlan_features(). The can_checksum_protocol function is not equipped to consider a protocol that does not require checksumming. Calling it for a protocol that requires no checksum is inappropriate. The patch below has harmonize_features call can_checksum_protocol when the protocol needs a checksum, so that the network layer is not forced to perform unnecessary skb linearization on the transmission of AoE packets. Unnecessary linearization results in decreased performance and increased memory pressure, as reported here: http://www.spinics.net/lists/linux-mm/msg15184.html The problem has probably not been widely experienced yet, because only recently has the kernel.org-distributed aoe driver acquired the ability to use payloads of over a page in size, with the patchset recently included in the mm tree: https://lkml.org/lkml/2012/8/28/140 The coraid.com-distributed aoe driver already could use payloads of greater than a page in size, but its users generally do not use the newest kernels. Signed-off-by:
-
Alan Cox authored
[ Upstream commit 6cf5c951 ] Check for an error from this and if so bail properly. Signed-off-by:
-
Eric Dumazet authored
[ Upstream commit c0cc88a7 ] While investigating l2tp bug, I hit a bug in eth_type_trans(), because not enough bytes were pulled in skb head. Signed-off-by:
Eric Dumazet <edumazet@google.com> Signed-off-by:
-
Eric Dumazet authored
[ Upstream commit 96af69ea ] mip6_mh_filter() should not modify its input, or else its caller would need to recompute ipv6_hdr() if skb->head is reallocated. Use skb_header_pointer() instead of pskb_may_pull() Signed-off-by:
-
Eric Dumazet authored
[ Upstream commit 1b05c4b5 ] icmpv6_filter() should not modify its input, or else its caller would need to recompute ipv6_hdr() if skb->head is reallocated. Use skb_header_pointer() instead of pskb_may_pull() and change the prototype to make clear both sk and skb are const. Also, if icmpv6 header cannot be found, do not deliver the packet, as we do in IPv4. Signed-off-by:
-
Eric Dumazet authored
[ Upstream commit ab43ed8b ] icmp_filter() should not modify its input, or else its caller would need to recompute ip_hdr() if skb->head is reallocated. Use skb_header_pointer() instead of pskb_may_pull() and change the prototype to make clear both sk and skb are const. Signed-off-by:
-
Eric Dumazet authored
[ Upstream commit 3e10986d ] Its possible to use RAW sockets to get a crash in tcp_set_keepalive() / sk_reset_timer() Fix is to make sure socket is a SOCK_STREAM one. Reported-by:
Dave Jones <davej@redhat.com> Signed-off-by:
-
Chema Gonzalez authored
[ Upstream commit 68622342 ] In the current rxhash calculation function, while the sorting of the ports/addrs is coherent (you get the same rxhash for packets sharing the same 4-tuple, in both directions), ports and addrs are sorted independently. This implies packets from a connection between the same addresses but crossed ports hash to the same rxhash. For example, traffic between A=S:l and B=L:s is hashed (in both directions) from {L, S, {s, l}}. The same rxhash is obtained for packets between C=S:s and D=L:l. This patch ensures that you either swap both addrs and ports, or you swap none. Traffic between A and B, and traffic between C and D, get their rxhash from different sources ({L, S, {l, s}} for A<->B, and {L, S, {s, l}} for C<->D) The patch is co-written with Eric Dumazet <edumazet@google.com> Signed-off-by:
Chema Gonzalez <chema@google.com> Signed-off-by:
-
Xiaodong Xu authored
[ Upstream commit 2b018d57 ] When PPPOE is running over a virtual ethernet interface (e.g., a bonding interface) and the user tries to delete the interface in case the PPPOE state is ZOMBIE, the kernel will loop forever while unregistering net_device for the reference count is not decreased to zero which should have been done with dev_put(). Signed-off-by:
Xiaodong Xu <stid.smth@gmail.com> Signed-off-by:
-
Thomas Graf authored
[ Upstream commit 4c3a5bda ] SCTP charges wmem_alloc via sctp_set_owner_w() in sctp_sendmsg() and via skb_set_owner_w() in sctp_packet_transmit(). If a sender runs out of sndbuf it will sleep in sctp_wait_for_sndbuf() and expects to be waken up by __sctp_write_space(). Buffer space charged via sctp_set_owner_w() is released in sctp_wfree() which calls __sctp_write_space() directly. Buffer space charged via skb_set_owner_w() is released via sock_wfree() which calls sk->sk_write_space() _if_ SOCK_USE_WRITE_QUEUE is not set. sctp_endpoint_init() sets SOCK_USE_WRITE_QUEUE on all sockets. Therefore if sctp_packet_transmit() manages to queue up more than sndbuf bytes, sctp_wait_for_sndbuf() will never be woken up again unless it is interrupted by a signal. This could be fixed by clearing the SOCK_USE_WRITE_QUEUE flag but ... Charging for the data twice does not make sense in the first place, it leads to overcharging sndbuf by a factor 2. Therefore this patch only charges a single byte in wmem_alloc when transmitting an SCTP packet to ensure that the socket stays alive until the packet has been released. This means that control chunks are no longer accounted for in wmem_alloc which I believe is not a problem as skb->truesize will typically lead to overcharging anyway and thus compensates for any control overhead. Signed-off-by:
Thomas Graf <tgraf@suug.ch> CC: Vlad Yasevich <vyasevic@redhat.com> CC: Neil Horman <nhorman@tuxdriver.com> CC: David Miller <davem@davemloft.net> Acked-by:
Vlad Yasevich <vyasevich@gmail.com> Signed-off-by:
-
Michal Kubeček authored
[ Upstream commit 15c04175 ] If recv() syscall is called for a TCP socket so that - IOAT DMA is used - MSG_WAITALL flag is used - requested length is bigger than sk_rcvbuf - enough data has already arrived to bring rcv_wnd to zero then when tcp_recvmsg() gets to calling sk_wait_data(), receive window can be still zero while sk_async_wait_queue exhausts enough space to keep it zero. As this queue isn't cleaned until the tcp_service_net_dma() call, sk_wait_data() cannot receive any data and blocks forever. If zero receive window and non-empty sk_async_wait_queue is detected before calling sk_wait_data(), process the queue first. Signed-off-by:
Michal Kubecek <mkubecek@suse.cz> Signed-off-by:
-
Gao feng authored
[ Upstream commit 6825a26c ] as we hold dst_entry before we call __ip6_del_rt, so we should alse call dst_release not only return -ENOENT when the rt6_info is ip6_null_entry. and we already hold the dst entry, so I think it's safe to call dst_release out of the write-read lock. Signed-off-by:
Gao feng <gaofeng@cn.fujitsu.com> Signed-off-by:
-
Antonio Quartulli authored
[ Upstream commit 5316cf9a ] skb_reset_mac_len() relies on the value of the skb->network_header pointer, therefore we must wait for such pointer to be recalculated before computing the new mac_len value. Signed-off-by:
Antonio Quartulli <ordex@autistici.org> Signed-off-by:
-
Lennart Sorensen authored
[ Upstream commit 2120c52d ] I discovered I couldn't get sierra_net to work on a powerpc. Turns out the firmware attribute check assumes the system is little endian and hence fails because the attributes is a 16 bit value. Signed-off-by:
Len Sorensen <lsorense@csclub.uwaterloo.ca> Signed-off-by:
-
Paolo Valente authored
[ Upstream commit 71261956 ] If the old timestamps of a class, say cl, are stale when the class becomes active, then QFQ may assign to cl a much higher start time than the maximum value allowed. This may happen when QFQ assigns to the start time of cl the finish time of a group whose classes are characterized by a higher value of the ratio max_class_pkt/weight_of_the_class with respect to that of cl. Inserting a class with a too high start time into the bucket list corrupts the data structure and may eventually lead to crashes. This patch limits the maximum start time assigned to a class. Signed-off-by:
Paolo Valente <paolo.valente@unimore.it> Signed-off-by:
-
Eric Dumazet authored
[ Upstream commit bdfc87f7 ] Its possible to setup a bad cbq configuration leading to an infinite loop in cbq_classify() DEV_OUT=eth0 ICMP="match ip protocol 1 0xff" U32="protocol ip u32" DST="match ip dst" tc qdisc add dev $DEV_OUT root handle 1: cbq avpkt 1000 \ bandwidth 100mbit tc class add dev $DEV_OUT parent 1: classid 1:1 cbq \ rate 512kbit allot 1500 prio 5 bounded isolated tc filter add dev $DEV_OUT parent 1: prio 3 $U32 \ $ICMP $DST 192.168.3.234 flowid 1: Reported-by:
Denys Fedoryschenko <denys@visp.net.lb> Tested-by:
-
Nikolay Aleksandrov authored
[ Upstream commit e4d1aa40 ] Add a check if pdev->bus->self == NULL (root bus). When attaching a netxen NIC to a VM it can be on the root bus and the guest would crash in netxen_mask_aer_correctable() because of a NULL pointer dereference if CONFIG_PCIEAER is present. Signed-off-by:
Nikolay Aleksandrov <nikolay@redhat.com> Signed-off-by:
-
Florian Fainelli authored
[ Upstream commit 0b836ddd ] Commit 36a12119 (netprio_cgroup.h: dont include module.h from other includes) made the following build error on ixp4xx_hss pop up: CC [M] drivers/net/wan/ixp4xx_hss.o drivers/net/wan/ixp4xx_hss.c:1412:20: error: expected ';', ',' or ')' before string constant drivers/net/wan/ixp4xx_hss.c:1413:25: error: expected ';', ',' or ')' before string constant drivers/net/wan/ixp4xx_hss.c:1414:21: error: expected ';', ',' or ')' before string constant drivers/net/wan/ixp4xx_hss.c:1415:19: error: expected ';', ',' or ')' before string constant make[8]: *** [drivers/net/wan/ixp4xx_hss.o] Error 1 This was previously hidden because ixp4xx_hss includes linux/hdlc.h which includes linux/netdevice.h which includes linux/netprio_cgroup.h which used to include linux/module.h. The real issue was actually present since the initial commit that added this driver since it uses macros from linux/module.h without including this file. Signed-off-by:
Florian Fainelli <florian@openwrt.org> Signed-off-by:
-
htbegin authored
[ Upstream commit ffb5ba90 ] chan->count is used by rx channel. If the desc count is not updated by the clean up loop in cpdma_chan_stop, the value written to the rxfree register in cpdma_chan_start will be incorrect. Signed-off-by:
Tao Hou <hotforest@gmail.com> Signed-off-by:
-
Mathias Krause authored
[ Upstream commit ecd79187 ] The current code fails to ensure that the netlink message actually contains as many bytes as the header indicates. If a user creates a new state or updates an existing one but does not supply the bytes for the whole ESN replay window, the kernel copies random heap bytes into the replay bitmap, the ones happen to follow the XFRMA_REPLAY_ESN_VAL netlink attribute. This leads to following issues: 1. The replay window has random bits set confusing the replay handling code later on. 2. A malicious user could use this flaw to leak up to ~3.5kB of heap memory when she has access to the XFRM netlink interface (requires CAP_NET_ADMIN). Known users of the ESN replay window are strongSwan and Steffen's iproute2 patch (<http://patchwork.ozlabs.org/patch/85962/>). The latter uses the interface with a bitmap supplied while the former does not. strongSwan is therefore prone to run into issue 1. To fix both issues without breaking existing userland allow using the XFRMA_REPLAY_ESN_VAL netlink attribute with either an empty bitmap or a fully specified one. For the former case we initialize the in-kernel bitmap with zero, for the latter we copy the user supplied bitmap. For state updates the full bitmap must be supplied. To prevent overflows in the bitmap length calculation the maximum size of bmp_len is limited to 128 by this patch -- resulting in a maximum replay window of 4096 packets. This should be sufficient for all real life scenarios (RFC 4303 recommends a default replay window size of 64). Cc: Steffen Klassert <steffen.klassert@secunet.com> Cc: Martin Willi <martin@revosec.ch> Cc: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by:
Mathias Krause <minipli@googlemail.com> Signed-off-by:
-
Mathias Krause authored
[ Upstream commit e3ac104d ] The ESN replay window was already fully initialized in xfrm_alloc_replay_state_esn(). No need to copy it again. Cc: Steffen Klassert <steffen.klassert@secunet.com> Signed-off-by:
Steffen Klassert <steffen.klassert@secunet.com> Signed-off-by:
-
Mathias Krause authored
[ Upstream commit 1f86840f ] The memory used for the template copy is a local stack variable. As struct xfrm_user_tmpl contains multiple holes added by the compiler for alignment, not initializing the memory will lead to leaking stack bytes to userland. Add an explicit memset(0) to avoid the info leak. Initial version of the patch by Brad Spengler. Cc: Brad Spengler <spender@grsecurity.net> Signed-off-by:
-
