Add phylink support to Wangxun 10Gb Ethernet controller for the 10GBASE-R
interface.
Signed-off-by: Jiawen Wu <jiawenwu@trustnetic.com>
Reviewed-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>

Register MDIO bus for PCS layer to use Synopsys designware XPCS, support
10GBASE-R interface to the controller.
Signed-off-by: Jiawen Wu <jiawenwu@trustnetic.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>

Add basic support for XPCS using 10GBASE-R interface. This mode will
be extended to use interrupt, so set pcs.poll false. And avoid soft
reset so that the device using this mode is in the default configuration.
Signed-off-by: Jiawen Wu <jiawenwu@trustnetic.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>

Register GPIO chip and handle GPIO IRQ for SFP socket.
Signed-off-by: Jiawen Wu <jiawenwu@trustnetic.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>

Register SFP platform device to get modules information.
Signed-off-by: Jiawen Wu <jiawenwu@trustnetic.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Piotr Raczynski <piotr.raczynski@intel.com>
Reviewed-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>

Register the platform device to use Designware I2C bus master driver.
Use regmap to read/write I2C device region from given base offset.
Signed-off-by: Jiawen Wu <jiawenwu@trustnetic.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Piotr Raczynski <piotr.raczynski@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>

In order for I2C to be able to work in standard mode, register a fixed
rate clock for each I2C device.
Signed-off-by: Jiawen Wu <jiawenwu@trustnetic.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>

Register software nodes for GPIO, I2C, SFP and PHYLINK. Define the
device properties.
Signed-off-by: Jiawen Wu <jiawenwu@trustnetic.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Piotr Raczynski <piotr.raczynski@intel.com>
Reviewed-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>

Enable USXGMII mode for mv88e6393x chips. Tested on Marvell 88E6191X.
Signed-off-by: Michal Smulski <michal.smulski@ooma.com>
Link: https://lore.kernel.org/r/20230605174442.12493-1-msmulski2@gmail.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Maxime Chevallier says:

====================
Followup fixes for the dwmac and altera lynx conversion

Here's yet another version of the cleanup series for the TSE PCS replacement
by PCS Lynx. It includes Kconfig fixups, some missing initialisations
and a slight rework suggested by Russell for the dwmac cleanup sequence,
along with more explicit zeroing of local structures as per MAciej's
review.
====================

Link: https://lore.kernel.org/r/20230607135941.407054-1-maxime.chevallier@bootlin.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Explicitly zero-ize the local mdio_regmap_config data, and explicitly
set the .autoscan parameter, as we only have a PCS on this bus.

Fixes: 5d1f3fe7 ("net: stmmac: dwmac-sogfpga: use the lynx pcs driver")
Suggested-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Suggested-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Set the .autoscan flag to false on the regmap-mdio bus, to avoid using a
random uninitialized value. We don't want autoscan in this case as the
mdio device is a PCS and not a PHY.

Fixes: db48abba ("net: ethernet: altera-tse: Convert to mdio-regmap and use PCS Lynx")
Suggested-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

So far, only the dwmac_socfpga variant of stmmac uses PCS Lynx. Use a
dedicated cleanup sequence for dwmac_socfpga instead of using the
generic stmmac one.

Fixes: 5d1f3fe7 ("net: stmmac: dwmac-sogfpga: use the lynx pcs driver")
Suggested-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Use the correct Kconfig dependency for altera_tse as PCS_ALTERA_TSE was
replaced by PCS_LYNX.

Fixes: db48abba ("net: ethernet: altera-tse: Convert to mdio-regmap and use PCS Lynx")
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

The regmap_config and mdio_regmap_config objects needs to be zeroed before
using them. This will cause spurious errors at probe time as config->pad_bits
is containing random uninitialized data.

Fixes: db48abba ("net: ethernet: altera-tse: Convert to mdio-regmap and use PCS Lynx")
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Jakub Kicinski says:

====================
tools: ynl: generate code for the handshake family

Add necessary features and generate user space C code for serializing
/ deserializing messages of the handshake family.

In addition to basics already present in netdev and fou, handshake
has nested attrs and multi-attr u32.
====================

Link: https://lore.kernel.org/r/20230606194302.919343-1-kuba@kernel.orgSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Generate support for the handshake family.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

When parsing multi-attr we count the objects and then allocate
an array to hold the parsed objects. If an attr space has multiple
multi-attr objects, however, if parsing the first array fails
we'll leave the object count for the second even tho the second
array was never allocated.

This may cause crashes when freeing objects on error.

Count attributes to a variable on the stack and only set the count
in the object once the memory was allocated.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

The handshake family needs support for MultiAttr scalars.
Right now we only support code gen for MultiAttr nested
types.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

txgbe_shutdown() relies on txgbe_dev_shutdown() to initialise
wake by passing it by reference. However, txgbe_dev_shutdown()
doesn't use this parameter at all.

wake is then passed uninitialised by txgbe_dev_shutdown()
to pci_wake_from_d3().

Resolve this problem by:
* Removing the unused parameter from txgbe_dev_shutdown()
* Removing the uninitialised variable wake from txgbe_dev_shutdown()
* Passing false to pci_wake_from_d3() - this assumes that
  although uninitialised wake was in practice false (0).

I'm not sure that this counts as a bug, as I'm not sure that
it manifests in any unwanted behaviour. But in any case, the issue
was introduced by:

  3ce7547e ("net: txgbe: Add build support for txgbe")

Flagged by Smatch as:

  .../txgbe_main.c:486 txgbe_shutdown() error: uninitialized symbol 'wake'.

No functional change intended.
Compile tested only.
Signed-off-by: Simon Horman <horms@kernel.org>
Reviewed-by: Jiawen Wu <jiawenwu@trustnetic.com>
Reviewed-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pointer variables of (void*) type do not require type cast.
Signed-off-by: Atin Bainada <hi@atinb.me>
Signed-off-by: David S. Miller <davem@davemloft.net>

With CONFIG_LIQUIDIO=m and CONFIG_LIQUIDIO_VF=y (or vice versa),
$(common-objs) are linked to a module and also to vmlinux even though
the expected CFLAGS are different between builtins and modules.

This is the same situation as fixed by commit 637a642f ("zstd:
Fixing mixed module-builtin objects").

Introduce the new module, liquidio-core, to provide the common functions
to liquidio and liquidio-vf.
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Fix incorrectly formatted tcp_syn_linear_timeouts sysctl in the
ipv4_net_table.

Fixes: ccce324d ("tcp: make the first N SYN RTO backoffs linear")
Signed-off-by: David Morley <morleyd@google.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Tested-by: David Morley <morleyd@google.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This error path needs call mutex_unlock(&ocelot->tas_lock) before
returning.

Fixes: 2d800bc5 ("net/sched: taprio: replace tc_taprio_qopt_offload :: enable with a "cmd" enum")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Detlev Casanova says:

====================
net: phy: realtek: Support external PHY clock

Some PHYs can use an external clock that must be enabled before
communicating with them.

Changes since v3:
 * Do not call genphy_suspend if WoL is enabled.
Changes since v2:
 * Reword documentation commit message
Changes since v1:
 * Remove the clock name as it is not guaranteed to be identical across
   different PHYs
 * Disable/Enable the clock when suspending/resuming
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

For PHYs that call rtl821x_probe() where an external clock can be
configured, make sure that the clock is disabled
when ->suspend() is called and enabled on resume.

The PHY_ALWAYS_CALL_SUSPEND is added to ensure that the suspend function
is actually always called.
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: Detlev Casanova <detlev.casanova@collabora.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Ethern PHYs can have external an clock that needs to be activated before
communicating with the PHY.
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Detlev Casanova <detlev.casanova@collabora.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In some cases, the PHY can use an external clock source instead of a
crystal.

Add an optional clock in the phy node to make sure that the clock source
is enabled, if specified, before probing.
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Detlev Casanova <detlev.casanova@collabora.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Allocate the size of rx indirection table dynamically in netvsc
from the value of size provided by OID_GEN_RECEIVE_SCALE_CAPABILITIES
query instead of using a constant value of ITAB_NUM.
Signed-off-by: Shradha Gupta <shradhagupta@linux.microsoft.com>
Reviewed-by: Haiyang Zhang <haiyangz@microsoft.com>
Tested-on: Ubuntu22 (azure VM, SKU size: Standard_F72s_v2)
Testcases:
1. ethtool -x eth0 output
2. LISA testcase:PERF-NETWORK-TCP-THROUGHPUT-MULTICONNECTION-NTTTCP-Synthetic
3. LISA testcase:PERF-NETWORK-TCP-THROUGHPUT-MULTICONNECTION-NTTTCP-SRIOV
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Replace these open-code bearer rcu_dereference access with bearer_get(),
like other places in bearer.c. While at it, also use tipc_net() instead
of net_generic(net, tipc_net_id) to get "tn" in bearer.c.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Reviewed-by: Larysa Zaremba <larysa.zaremba@intel.com>
Reviewed-by: Tung Nguyen <tung.q.nguyen@dektech.com.au>
Link: https://lore.kernel.org/r/1072588a8691f970bda950c7e2834d1f2983f58e.1685976044.git.lucien.xin@gmail.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Guillaume Nault says:

====================
ipv4: Remove RT_CONN_FLAGS() calls in flowi4_init_output().

Remove a few RT_CONN_FLAGS() calls used inside flowi4_init_output().
These users can be easily converted to set the scope properly, instead
of overloading the tos parameter with scope information as done by
RT_CONN_FLAGS().

The objective is to eventually remove RT_CONN_FLAGS() entirely, which
will then allow to also remove RTO_ONLINK and to finally convert
->flowi4_tos to dscp_t.
====================

Link: https://lore.kernel.org/r/cover.1685999117.git.gnault@redhat.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

RT_CONN_FLAGS(sk) overloads flowi4_tos with the RTO_ONLINK bit when
sk has the SOCK_LOCALROUTE flag set. This allows
ip_route_output_key_hash() to eventually adjust flowi4_scope.

Instead of relying on special handling of the RTO_ONLINK bit, we can
just set the route scope correctly. This will eventually allow to avoid
special interpretation of tos variables and to convert ->flowi4_tos to
dscp_t.
Signed-off-by: Guillaume Nault <gnault@redhat.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

RT_CONN_FLAGS(sk) overloads the tos parameter with the RTO_ONLINK bit
when sk has the SOCK_LOCALROUTE flag set. This is only useful for
ip_route_output_key_hash() to eventually adjust the route scope.

Let's drop RTO_ONLINK and set the correct scope directly to avoid this
special case in the future and to allow converting ->flowi4_tos to
dscp_t.
Signed-off-by: Guillaume Nault <gnault@redhat.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Robert Hancock says:

====================
Move KSZ9477 errata handling to PHY driver

Patches to move handling for KSZ9477 PHY errata register fixes from
the DSA switch driver into the corresponding PHY driver, for more
proper layering and ordering.
====================

Link: https://lore.kernel.org/r/20230605153943.1060444-1-robert.hancock@calian.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

The KSZ9477 PHY errata handling code has now been moved into the Micrel
PHY driver, so it is no longer needed inside the DSA switch driver.
Remove it.
Signed-off-by: Robert Hancock <robert.hancock@calian.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

The ksz9477 DSA switch driver is currently updating some MMD registers
on the internal port PHYs to address some chip errata. However, these
errata are really a property of the PHY itself, not the switch they are
part of, so this is kind of a layering violation. It makes more sense for
these writes to be done inside the driver which binds to the PHY and not
the driver for the containing device.

This also addresses some issues where the ordering of when these writes
are done may have been incorrect, causing the link to erratically fail to
come up at the proper speed or at all. Doing this in the PHY driver
during config_init ensures that they happen before anything else tries to
change the state of the PHY on the port.

The new code also ensures that autonegotiation is disabled during the
register writes and re-enabled afterwards, as indicated by the latest
version of the errata documentation from Microchip.
Signed-off-by: Robert Hancock <robert.hancock@calian.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Jakub Kicinski says:

====================
tools: ynl: user space C

Use the code gen which is already in tree to generate a user space
library for a handful of simple families. I find YNL C quite useful
in some WIP projects, and I think others may find it useful, too.
I was hoping someone will pick this work up and finish it...
but it seems that Python YNL has largely stolen the thunder.
Python may not be great for selftest, tho, and actually this lib
is more fully-featured. The Python script was meant as a quick demo,
funny how those things go.

v2: https://lore.kernel.org/all/20230604175843.662084-1-kuba@kernel.org/
v1: https://lore.kernel.org/all/20230603052547.631384-1-kuba@kernel.org/
====================

Link: https://lore.kernel.org/r/20230605190108.809439-1-kuba@kernel.orgSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Add a sample application using the C library.
My main goal is to make writing selftests easier but until
I have some of those ready I think it's useful to show off
the functionality and let people poke and tinker.

Sample outputs - dump:

$ ./netdev
Select ifc ($ifindex; or 0 = dump; or -2 ntf check): 0
      lo[1]	0:
  enp1s0[2]	23: basic redirect rx-sg

Notifications (watching veth pair getting added and deleted):

$ ./netdev
Select ifc ($ifindex; or 0 = dump; or -2 ntf check): -2
[53]	0: (ntf: dev-add-ntf)
[54]	0: (ntf: dev-add-ntf)
[54]	23: basic redirect rx-sg (ntf: dev-change-ntf)
[53]	23: basic redirect rx-sg (ntf: dev-change-ntf)
[53]	23: basic redirect rx-sg (ntf: dev-del-ntf)
[54]	23: basic redirect rx-sg (ntf: dev-del-ntf)
Reviewed-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Generate the code for netdev and fou families. They are simple
and already supported by the code gen.
Reviewed-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Add "fixed" part of the user space Netlink Spec-based library.
This will get linked with the protocol implementations to form
a full API.
Acked-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>