The type of the data for the main Arizona IRQ chip should be struct
arizona not struct regmap_irq_chip_data. The bug is harmless but should
probably be corrected anyway.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

The driver always checks for pdata being NULL except in one place.
Add a check to prevent a possible NULL pointer deference error.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

On Odroid XU3 board (with S2MPS11 PMIC) the PWRHOLD bit in CTRL1
register must be manually set to 0 before initiating power off sequence.

One of usual power down methods for Exynos based devices looks like:
1. PWRHOLD pin of PMIC is connected to PSHOLD of Exynos SoC.
2. Exynos holds up this pin during system operation.
3. ACOKB pin of PMIC is pulled up to VBATT and optionally to pin in
   other device.
4. When PWRHOLD/PSHOLD goes low, the PMIC will turn off the power if
   ACOKB goes high.

On Odroid XU3 family the difference is in (3) - the ACOKB is grounded.
This means that PMIC must manually set PWRHOLD field to low and then
wait for signal from Application Processor (the usual change in
PWRHOLD/PSHOLD pin will actually cut off the power).

The patch adds respective binding allowing Odroid XU3 device to be
powered off.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
Reported-by: Anand Moon <linux.amoon@gmail.com>
Tested-by: Anand Moon <linux.amoon@gmail.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

There are already helper functions to do 64-bit I/O on 32-bit machines, thus we
don't need to reinvent the wheel. In our case we can't use readq() / writeq()
even on 64-bit kernel since there is a hardware limitation (OCP bus is a 32-bit
bus).
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

This platform driver has a OF device ID table but the OF module
alias information is not created so module autoloading won't work.
Signed-off-by: Luis de Bethencourt <luisbg@osg.samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

This platform driver has a OF device ID table but the OF module
alias information is not created so module autoloading won't work.
Signed-off-by: Luis de Bethencourt <luisbg@osg.samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

This platform driver has a OF device ID table but the OF module
alias information is not created so module autoloading won't work.
Signed-off-by: Luis de Bethencourt <luisbg@osg.samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

This platform driver has a OF device ID table but the OF module
alias information is not created so module autoloading won't work.
Signed-off-by: Luis de Bethencourt <luisbg@osg.samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

Introduced by:
commit 8019ff6c ("regmap: Use reg_sequence for multi_reg_write / register_patch")

Interacting with:
commit 561629755a21 ("mfd: arizona: Add support for WM8998 and WM1814")
commit 81207880 ("mfd: wm5110: Add register patch for rev E and above")
Signed-off-by: Nariman Poushin <nariman@opensource.wolfsonmicro.com>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

On the STMPE2401 and STMPE2401 altfunction 1 corresponds to the
PWM channels. This oneliner was missing in the case-switch, making
it impossible to enable the PWM channel output.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

Commit 68bab866 ("mfd: twl6040: Optional clk32k clock handling")
added clock handling for the 32k clock from palmas-clk. However, that
patch did not consider a typical situation where twl6040 is built-in,
and palmas-clk is a loadable module like we have in omap2plus_defconfig.

If palmas-clk is not loaded before twl6040 probes, we will get a
"clk32k is not handled" warning during booting. This means that any
drivers relying on this clock will mysteriously fail, including
omap5-uevm WLAN and audio.

Note that for WLAN, we probably should also eventually get
the clk32kgaudio for MMC3 directly as that's shared between
audio and WLAN SDIO at least for omap5-uevm. It seems the
WLAN chip cannot get it as otherwise MMC3 won't get properly
probed.

Fixes: 68bab866 ("mfd: twl6040: Optional clk32k clock handling")
Signed-off-by: Tony Lindgren <tony@atomide.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

Add chip identification support for 88PM860 device
to the pm80x_chip_mapping table.
Signed-off-by: Vaibhav Hiremath <vaibhav.hiremath@linaro.org>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

The Documentation/devicetree/bindings/mfd/cros-ec.txt DT binding doc lists
"google,cros-ec-i2c" as a compatible string but the corresponding driver
does not have an OF match table. Add the table to the driver so the I2C
core can do an OF style match.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

Merge branches 'ib-extcon-mfd-4.4', 'ib-mfd-i2c-v4.4', 'ib-mfd-power-4.4', 'ib-mfd-regmap-4.4' and 'ib-mfd-regulator-4.4' into ibs-for-mfd-merged

There is a 24c08 chip connected to i2c bus on Intel Galileo Gen2 board. Enable
it via ACPI ID INT3499.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

On Intel Galileo Gen2 the GPIO expanders are connected to the i2c bus. For
those devices the ACPI table has specific parameters that refer to an actual
i2c host controller. Since MFD now copes with that specific configuration we
have to provide a necessary information how to distinguish devices in ACPI
namespace. Here the _ADR values are provided.
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

On Intel Galileo boards the GPIO expander is connected to i2c bus. Moreover it
is able to generate interrupt, but interrupt line is connected to GPIO. That's
why we have to have GPIO driver in place when we will probe i2c host with
device connected to it.
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

There is at least one board on the market, i.e. Intel Galileo Gen2, that uses
_ADR to distinguish the devices under one actual device. Due to this we have to
improve the quirk in the MFD core to handle that board.
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

Suggested-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

When referencing other DT bindings documentation, use relative
path rather than absolute.
Suggested-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

Signed-off-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Acked-by: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

This adds power supply driver support for the Fuel-Gauge part of
the DA9150 combined Charger and Fuel-Gauge device.
Signed-off-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Acked-by: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

Signed-off-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

Signed-off-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

This patch modifies tps6105x and associated function driver to use regmap
instead of operating directly on i2c.
Signed-off-by: Denis Grigoryev <grigoryev@fastwel.ru>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

Pull strscpy string copy function implementation from Chris Metcalf.

Chris sent this during the merge window, but I waffled back and forth on
the pull request, which is why it's going in only now.

The new "strscpy()" function is definitely easier to use and more secure
than either strncpy() or strlcpy(), both of which are horrible nasty
interfaces that have serious and irredeemable problems.

strncpy() has a useless return value, and doesn't NUL-terminate an
overlong result.  To make matters worse, it pads a short result with
zeroes, which is a performance disaster if you have big buffers.

strlcpy(), by contrast, is a mis-designed "fix" for strlcpy(), lacking
the insane NUL padding, but having a differently broken return value
which returns the original length of the source string.  Which means
that it will read characters past the count from the source buffer, and
you have to trust the source to be properly terminated.  It also makes
error handling fragile, since the test for overflow is unnecessarily
subtle.

strscpy() avoids both these problems, guaranteeing the NUL termination
(but not excessive padding) if the destination size wasn't zero, and
making the overflow condition very obvious by returning -E2BIG.  It also
doesn't read past the size of the source, and can thus be used for
untrusted source data too.

So why did I waffle about this for so long?

Every time we introduce a new-and-improved interface, people start doing
these interminable series of trivial conversion patches.

And every time that happens, somebody does some silly mistake, and the
conversion patch to the improved interface actually makes things worse.
Because the patch is mindnumbing and trivial, nobody has the attention
span to look at it carefully, and it's usually done over large swatches
of source code which means that not every conversion gets tested.

So I'm pulling the strscpy() support because it *is* a better interface.
But I will refuse to pull mindless conversion patches.  Use this in
places where it makes sense, but don't do trivial patches to fix things
that aren't actually known to be broken.

* 'strscpy' of git://git.kernel.org/pub/scm/linux/kernel/git/cmetcalf/linux-tile:
  tile: use global strscpy() rather than private copy
  string: provide strscpy()
  Make asm/word-at-a-time.h available on all architectures

Pull md fixes from Neil Brown:
 "Assorted fixes for md in 4.3-rc.

  Two tagged for -stable, and one is really a cleanup to match and
  improve kmemcache interface.

* tag 'md/4.3-fixes' of git://neil.brown.name/md:
  md/bitmap: don't pass -1 to bitmap_storage_alloc.
  md/raid1: Avoid raid1 resync getting stuck
  md: drop null test before destroy functions
  md: clear CHANGE_PENDING in readonly array
  md/raid0: apply base queue limits *before* disk_stack_limits
  md/raid5: don't index beyond end of array in need_this_block().
  raid5: update analysis state for failed stripe
  md: wait for pending superblock updates before switching to read-only

Pull MIPS updates from Ralf Baechle:
 "This week's round of MIPS fixes:
   - Fix JZ4740 build
   - Fix fallback to GFP_DMA
   - FP seccomp in case of ENOSYS
   - Fix bootmem panic
   - A number of FP and CPS fixes
   - Wire up new syscalls
   - Make sure BPF assembler objects can properly be disassembled
   - Fix BPF assembler code for MIPS I"

* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus:
  MIPS: scall: Always run the seccomp syscall filters
  MIPS: Octeon: Fix kernel panic on startup from memory corruption
  MIPS: Fix R2300 FP context switch handling
  MIPS: Fix octeon FP context switch handling
  MIPS: BPF: Fix load delay slots.
  MIPS: BPF: Do all exports of symbols with FEXPORT().
  MIPS: Fix the build on jz4740 after removing the custom gpio.h
  MIPS: CPS: #ifdef on CONFIG_MIPS_MT_SMP rather than CONFIG_MIPS_MT
  MIPS: CPS: Don't include MT code in non-MT kernels.
  MIPS: CPS: Stop dangling delay slot from has_mt.
  MIPS: dma-default: Fix 32-bit fall back to GFP_DMA
  MIPS: Wire up userfaultfd and membarrier syscalls.

Pull irq fixes from Thomas Gleixner:
 "This update contains:

   - Fix for a long standing race affecting /proc/irq/NNN

   - One line fix for ARM GICV3-ITS counting the wrong data

   - Warning silencing in ARM GICV3-ITS.  Another GCC trying to be
     overly clever issue"

* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  irqchip/gic-v3-its: Count additional LPIs for the aliased devices
  irqchip/gic-v3-its: Silence warning when its_lpi_alloc_chunks gets inlined
  genirq: Fix race in register_irq_proc()

The MIPS syscall handler code used to return -ENOSYS on invalid
syscalls. Whilst this is expected, it caused problems for seccomp
filters because the said filters never had the change to run since
the code returned -ENOSYS before triggering them. This caused
problems on the chromium testsuite for filters looking for invalid
syscalls. This has now changed and the seccomp filters are always
run even if the syscall is invalid. We return -ENOSYS once we
return from the seccomp filters. Moreover, similar codepaths have
been merged in the process which simplifies somewhat the overall
syscall code.
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/11236/Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

Pull x86 fixes from Ingo Molnar:
 "Fixes all around the map: W+X kernel mapping fix, WCHAN fixes, two
  build failure fixes for corner case configs, x32 header fix and a
  speling fix"

* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/headers/uapi: Fix __BITS_PER_LONG value for x32 builds
  x86/mm: Set NX on gap between __ex_table and rodata
  x86/kexec: Fix kexec crash in syscall kexec_file_load()
  x86/process: Unify 32bit and 64bit implementations of get_wchan()
  x86/process: Add proper bound checks in 64bit get_wchan()
  x86, efi, kasan: Fix build failure on !KASAN && KMEMCHECK=y kernels
  x86/hyperv: Fix the build in the !CONFIG_KEXEC_CORE case
  x86/cpufeatures: Correct spelling of the HWP_NOTIFY flag

Pull timer fixes from Ingo Molnar:
 "An abs64() fix in the watchdog driver, and two clocksource driver
  NO_IRQ assumption fixes"

* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  clocksource: Fix abs() usage w/ 64bit values
  clocksource/drivers/keystone: Fix bad NO_IRQ usage
  clocksource/drivers/rockchip: Fix bad NO_IRQ usage

Pull EFI fixes from Ingo Molnar:
 "Two EFI fixes: one for x86, one for ARM, fixing a boot crash bug that
  can trigger under newer EFI firmware"

* 'core-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  arm64/efi: Fix boot crash by not padding between EFI_MEMORY_RUNTIME regions
  x86/efi: Fix boot crash by mapping EFI memmap entries bottom-up at runtime, instead of top-down

Pull drm fixes from Dave Airlie:
 "Bunch of fixes all over the place, all pretty small: amdgpu, i915,
  exynos, one qxl and one vmwgfx.

  There is also a bunch of mst fixes, I left some cleanups in the series
  as I didn't think it was worth splitting up the tested series"

* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux: (37 commits)
  drm/dp/mst: add some defines for logical/physical ports
  drm/dp/mst: drop cancel work sync in the mstb destroy path (v2)
  drm/dp/mst: split connector registration into two parts (v2)
  drm/dp/mst: update the link_address_sent before sending the link address (v3)
  drm/dp/mst: fixup handling hotplug on port removal.
  drm/dp/mst: don't pass port into the path builder function
  drm/radeon: drop radeon_fb_helper_set_par
  drm: handle cursor_set2 in restore_fbdev_mode
  drm/exynos: Staticize local function in exynos_drm_gem.c
  drm/exynos: fimd: actually disable dp clock
  drm/exynos: dp: remove suspend/resume functions
  drm/qxl: recreate the primary surface when the bo is not primary
  drm/amdgpu: only print meaningful VM faults
  drm/amdgpu/cgs: remove import_gpu_mem
  drm/i915: Call non-locking version of drm_kms_helper_poll_enable(), v2
  drm: Add a non-locking version of drm_kms_helper_poll_enable(), v2
  drm/vmwgfx: Fix a command submission hang regression
  drm/exynos: remove unused mode_fixup() code
  drm/exynos: remove decon_mode_fixup()
  drm/exynos: remove fimd_mode_fixup()
  ...

Pull input layer fixes from Dmitry Torokhov:
 "Fixes for two recent regressions (in Synaptics PS/2 and uinput
  drivers) and some more driver fixups"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
  Revert "Input: synaptics - fix handling of disabling gesture mode"
  Input: psmouse - fix data race in __ps2_command
  Input: elan_i2c - add all valid ic type for i2c/smbus
  Input: zhenhua - ensure we have BITREVERSE
  Input: omap4-keypad - fix memory leak
  Input: serio - fix blocking of parport
  Input: uinput - fix crash when using ABS events
  Input: elan_i2c - expand maximum product_id form 0xFF to 0xFFFF
  Input: elan_i2c - add ic type 0x03
  Input: elan_i2c - don't require known iap version
  Input: imx6ul_tsc - fix controller name
  Input: imx6ul_tsc - use the preferred method for kzalloc()
  Input: imx6ul_tsc - check for negative return value
  Input: imx6ul_tsc - propagate the errors
  Input: walkera0701 - fix abs() calculations on 64 bit values
  Input: mms114 - remove unneded semicolons
  Input: pm8941-pwrkey - remove unneded semicolon
  Input: fix typo in MT documentation
  Input: cyapa - fix address of Gen3 devices in device tree documentation

This patch fixes one cases where abs() was being used with 64-bit
nanosecond values, where the result may be capped at 32-bits.

This potentially could cause watchdog false negatives on 32-bit
systems, so this patch addresses the issue by using abs64().
Signed-off-by: John Stultz <john.stultz@linaro.org>
Cc: Prarit Bhargava <prarit@redhat.com>
Cc: Richard Cochran <richardcochran@gmail.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: stable@vger.kernel.org
Link: http://lkml.kernel.org/r/1442279124-7309-2-git-send-email-john.stultz@linaro.orgSigned-off-by: Thomas Gleixner <tglx@linutronix.de>

Pull arm64 fixes from Catalin Marinas:

 - Fix for transparent huge page change_protection() logic which was
   inadvertently changing a huge pmd page into a pmd table entry.

 - Function graph tracer panic fix caused by the return_to_handler code
   corrupting the multi-regs function return value (composite types).

* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
  arm64: ftrace: fix function_graph tracer panic
  arm64: Fix THP protection change logic

Pull m68k updates from Geert Uytterhoeven:
 "Summary:
   - Fix for accidental modification of arguments of syscall functions
   - Wire up new syscalls
   - Update defconfigs"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/linux-m68k:
  m68k/defconfig: Update defconfigs for v4.3-rc1
  m68k: Define asmlinkage_protect
  m68k: Wire up membarrier
  m68k: Wire up userfaultfd
  m68k: Wire up direct socket calls

When configuring the interrupt mapping for a new device, we
iterate over all the possible aliases to account for their
maximum MSI allocation. This was introduced by e8137f4f
("irqchip: gicv3-its: Iterate over PCI aliases to generate ITS configuration").

Turns out that the code doing that is a bit braindead, and repeatedly
accounts for the same device over and over.

Fix this by counting the actual alias that is passed to us by the
core code.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: Alex Shi <alex.shi@linaro.org>
Cc: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: David Daney <ddaney.cavm@gmail.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Link: http://lkml.kernel.org/r/1443800646-8074-3-git-send-email-marc.zyngier@arm.comSigned-off-by: Thomas Gleixner <tglx@linutronix.de>