IPQ6018 has temperature sensing HW block compatible with IPQ8074. Add
node for it.
Signed-off-by: Mantas Pucka <mantas@8devices.com>
Link: https://lore.kernel.org/r/1706173452-1017-3-git-send-email-mantas@8devices.comSigned-off-by: Bjorn Andersson <andersson@kernel.org>

Add proper audio routes for onboard analogue microphones AMIC[1345] -
MIC biases and route from TX macro codec to WCD9385 audio codec.

This should bring AMIC1, AMIC2 (headphones), AMIC3, AMIC4 and AMIC5
onboard microphones to work, although was not tested on the hardware.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20240124164505.293202-4-krzysztof.kozlowski@linaro.orgSigned-off-by: Bjorn Andersson <andersson@kernel.org>

Add proper audio routes for onboard analogue microphones AMIC[1345] -
MIC biases and route from TX macro codec to WCD9385 audio codec.

This finally brings AMIC1, AMIC3, AMIC4 and AMIC5 onboard microphones to
work.  AMIC2 (headphones) should be fine well, however it didn't work
during tests, probably because of incomplete USB switch.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20240124164505.293202-3-krzysztof.kozlowski@linaro.orgSigned-off-by: Bjorn Andersson <andersson@kernel.org>

WCD9385 audio codec TX port mapping was copied form HDK8450, but in fact
it is offset by one.  Correct it to fix recording via analogue
microphones.

The change is based on QRD8550 and should be correct here as well, but
was not tested on MTP8550.

Cc: stable@vger.kernel.org
Fixes: a541667c ("arm64: dts: qcom: sm8550-mtp: add WCD9385 audio-codec")
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20240124164505.293202-2-krzysztof.kozlowski@linaro.orgSigned-off-by: Bjorn Andersson <andersson@kernel.org>

WCD9385 audio codec TX port mapping was copied form HDK8450, but in fact
it is offset by one.  Correct it to fix recording via analogue
microphones.

Cc: stable@vger.kernel.org
Fixes: 83fae950 ("arm64: dts: qcom: sm8550-qrd: add WCD9385 audio-codec")
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20240124164505.293202-1-krzysztof.kozlowski@linaro.orgSigned-off-by: Bjorn Andersson <andersson@kernel.org>

Add the definitions for the various thermal zones found on the SM6350
SoC. Hooking up GPU and CPU cooling can limit the clock speeds there to
reduce the temperature again to good levels.

Most thermal zones only have one critical temperature configured at
125°C which can be mostly considered a placeholder until those zones can
be hooked up to cooling.
Signed-off-by: Luca Weiss <luca.weiss@fairphone.com>
Link: https://lore.kernel.org/r/20240124-sm6350-tsens-v1-1-d37ec82140af@fairphone.comSigned-off-by: Bjorn Andersson <andersson@kernel.org>

The USB3 PHY on the SM6115 platform doesn't have built-in
PCS_MISC_CLAMP_ENABLE register. Instead clamping is handled separately
via the register in the TCSR space. Declare corresponding register.

Fixes: 9dd5f6db ("arm64: dts: qcom: sm6115: Add USB SS qmp phy node")
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20240117-usbc-phy-vls-clamp-v2-6-a950c223f10f@linaro.orgSigned-off-by: Bjorn Andersson <andersson@kernel.org>

The USB3 PHY on the QCM2290 platform doesn't have built-in
PCS_MISC_CLAMP_ENABLE register. Instead clamping is handled separately
via the register in the TCSR space. Declare corresponding register.

Fixes: 0c55f622 ("arm64: dts: qcom: qcm2290: Add USB3 PHY")
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20240117-usbc-phy-vls-clamp-v2-5-a950c223f10f@linaro.orgSigned-off-by: Bjorn Andersson <andersson@kernel.org>

The USB3 PHY on the MSM8998 platform doesn't have built-in
PCS_MISC_CLAMP_ENABLE register. Instead clamping is handled separately
via the register in the TCSR space. Declare corresponding register.

Fixes: 026dad8f ("arm64: dts: qcom: msm8998: Add USB-related nodes")
Cc: Jeffrey Hugo <quic_jhugo@quicinc.com>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Reviewed-by: Jeffrey Hugo <quic_jhugo@quicinc.com>
Link: https://lore.kernel.org/r/20240117-usbc-phy-vls-clamp-v2-4-a950c223f10f@linaro.orgSigned-off-by: Bjorn Andersson <andersson@kernel.org>

QCM6490 uses Trustzone as firmware whereas SC7280 uses arm trusted firmware.
The PSCI suspend param and the number of domain-idle-states supported is
different in Trustzone for cluster sleep.

Move the arm trusted firmware supported domain-idle-states in chrome specific
sc7280-chrome-common.dtsi and add the Trustzone supported sleep states as default
domain-idle-states in sc7280.dtsi
Signed-off-by: Maulik Shah <quic_mkshah@quicinc.com>
Link: https://lore.kernel.org/r/20240109-qcm6490_cluster_sleep-v2-1-8f94f1ad188d@quicinc.comSigned-off-by: Bjorn Andersson <andersson@kernel.org>

The board-specific (electrical) configuration was removed from PM660L in
90ba636e ("arm64: dts: qcom: pm660l: Remove board-specific WLED
configuration") as it is platform-dependent.  We reintroduce it here in
the Nile board configuration (with a slightly lower current limit, as
per downstream DT sources) and enable it for use in the dsi0 node.
Signed-off-by: Marijn Suijten <marijn.suijten@somainline.org>
Link: https://lore.kernel.org/r/20240204-sdm630-nile-wled-v1-1-9f5c4f8147f2@somainline.orgSigned-off-by: Bjorn Andersson <andersson@kernel.org>

The idea impressed in the commit b32e592d ("devicetree: bindings:
Document qcom board compatible format") never got actually adopted. As
can be seen from the existing board DT files, no device actually used
the PMIC / foundry / version parts of the compatible string. Drop this
compatibility string description to avoid possible confusion and keep
just the generic terms and the SoC list.

Fixes: b32e592d ("devicetree: bindings: Document qcom board compatible format")
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20240204-qcom-drop-compat-v1-1-69d6cd92aa0e@linaro.orgSigned-off-by: Bjorn Andersson <andersson@kernel.org>

The qlink_logging memory region is also used by the modem firmware,
add it to the reserved memories and add it to the MPSS memory regions.
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Mukesh Ojha <quic_mojha@quicinc.com>
Link: https://lore.kernel.org/r/20240123-topic-sm8650-upstream-remoteproc-v7-4-61283f50162f@linaro.orgSigned-off-by: Bjorn Andersson <andersson@kernel.org>

Add Inline Crypto Engine reg and clocks in MMC node and enable CQE
support as Inline Crypto Engine requires CQE to be enabled.
Signed-off-by: Vignesh Viswanathan <quic_viswanat@quicinc.com>
Link: https://lore.kernel.org/r/20231215095339.3055554-1-quic_viswanat@quicinc.comSigned-off-by: Bjorn Andersson <andersson@kernel.org>

Add nodes for four WSA8845 speakers.  Unlike previous boards like
SM8550-QRD, this board has four speakers spread over two Soundwire buses
instead of two speakers on one bus.  Each pair of speakers shares the
reset GPIO thus pinctrl property is only in one of them.

Cc: Abel Vesa <abel.vesa@linaro.org>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20231214131016.30502-5-krzysztof.kozlowski@linaro.orgSigned-off-by: Bjorn Andersson <andersson@kernel.org>

Add Qualcomm Aqstic WCD9385 audio codec on two Soundwire interfaces: RX
and TX.

Cc: Abel Vesa <abel.vesa@linaro.org>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20231214131016.30502-4-krzysztof.kozlowski@linaro.orgSigned-off-by: Bjorn Andersson <andersson@kernel.org>

Add nodes for LPASS Soundwire v2.0.0 controllers.  Difference against
SM8550:
1. Update port configs to match reference implementation,
2. LPASS TLMM GPIO14 is not used as WCD_SR_TX_DATA2 pin but as GPIO
   (camera).

Cc: Abel Vesa <abel.vesa@linaro.org>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20231214131016.30502-3-krzysztof.kozlowski@linaro.orgSigned-off-by: Bjorn Andersson <andersson@kernel.org>

Add the Low Power Audio SubSystem (LPASS) / ADSP audio codec macros on
Qualcomm SM8650.  The nodes are exactly the same as on SM8550 and
SM8650.

Cc: Abel Vesa <abel.vesa@linaro.org>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20231214131016.30502-2-krzysztof.kozlowski@linaro.orgSigned-off-by: Bjorn Andersson <andersson@kernel.org>

Add the Low Power Audio SubSystem Low Power Island (LPASS LPI) pin
controller device node as part of audio subsystem in Qualcomm X1E80100
SoC.

Cc: Abel Vesa <abel.vesa@linaro.org>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20231212125632.54021-3-krzysztof.kozlowski@linaro.orgSigned-off-by: Bjorn Andersson <andersson@kernel.org>

Add the ADSP Generic Packet Router (GPR) device node as part of audio
subsystem in Qualcomm X1E80100 SoC.

Cc: Abel Vesa <abel.vesa@linaro.org>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20231212125632.54021-2-krzysztof.kozlowski@linaro.orgSigned-off-by: Bjorn Andersson <andersson@kernel.org>

Add node to support this bus inside of IPQ6018.
For example, this bus is used to work with the
voltage regulator (mp5496) on the Yuncore AX840 wireless AP.
Signed-off-by: Isaev Ruslan <legale.legale@gmail.com>
Link: https://lore.kernel.org/r/CACDmYyfOe-jcgj4BAD8=pr08sHpOF=+FRcwrouuLAVsa4+zwtw@mail.gmail.comSigned-off-by: Bjorn Andersson <andersson@kernel.org>

The LDOs 3E and 2J are actually supplied by SMPS 5J. Fix accordingly.

Fixes: af16b005 ("arm64: dts: qcom: Add base X1E80100 dtsi and the QCP dts")
Acked-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
Link: https://lore.kernel.org/r/20240129-x1e80100-dts-missing-nodes-v6-11-2c0e691cfa3b@linaro.orgSigned-off-by: Bjorn Andersson <andersson@kernel.org>

Enable display, pcie and usb support.
Co-developed-by: Sibi Sankar <quic_sibis@quicinc.com>
Signed-off-by: Sibi Sankar <quic_sibis@quicinc.com>
Co-developed-by: Rajendra Nayak <quic_rjendra@quicinc.com>
Signed-off-by: Rajendra Nayak <quic_rjendra@quicinc.com>
Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
Link: https://lore.kernel.org/r/20240129-x1e80100-dts-missing-nodes-v6-10-2c0e691cfa3b@linaro.orgSigned-off-by: Bjorn Andersson <andersson@kernel.org>

Enable touchscreen, touchpad, keyboard, display, pcie and usb
support.
Co-developed-by: Sibi Sankar <quic_sibis@quicinc.com>
Signed-off-by: Sibi Sankar <quic_sibis@quicinc.com>
Co-developed-by: Rajendra Nayak <quic_rjendra@quicinc.com>
Signed-off-by: Rajendra Nayak <quic_rjendra@quicinc.com>
Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
Link: https://lore.kernel.org/r/20240129-x1e80100-dts-missing-nodes-v6-9-2c0e691cfa3b@linaro.orgSigned-off-by: Bjorn Andersson <andersson@kernel.org>

Add the required nodes to support display on X1E80100.
Co-developed-by: Sibi Sankar <quic_sibis@quicinc.com>
Signed-off-by: Sibi Sankar <quic_sibis@quicinc.com>
Co-developed-by: Rajendra Nayak <quic_rjendra@quicinc.com>
Signed-off-by: Rajendra Nayak <quic_rjendra@quicinc.com>
Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
Link: https://lore.kernel.org/r/20240129-x1e80100-dts-missing-nodes-v6-8-2c0e691cfa3b@linaro.orgSigned-off-by: Bjorn Andersson <andersson@kernel.org>

Add nodes for PCIe 4 and 6 controllers and their PHYs for X1E80100 platform.
Co-developed-by: Sibi Sankar <quic_sibis@quicinc.com>
Signed-off-by: Sibi Sankar <quic_sibis@quicinc.com>
Co-developed-by: Rajendra Nayak <quic_rjendra@quicinc.com>
Signed-off-by: Rajendra Nayak <quic_rjendra@quicinc.com>
Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
Link: https://lore.kernel.org/r/20240129-x1e80100-dts-missing-nodes-v6-7-2c0e691cfa3b@linaro.orgSigned-off-by: Bjorn Andersson <andersson@kernel.org>

Add nodes for all USB controllers and their PHYs for X1E80100 platform.
Co-developed-by: Sibi Sankar <quic_sibis@quicinc.com>
Signed-off-by: Sibi Sankar <quic_sibis@quicinc.com>
Co-developed-by: Rajendra Nayak <quic_rjendra@quicinc.com>
Signed-off-by: Rajendra Nayak <quic_rjendra@quicinc.com>
Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
Link: https://lore.kernel.org/r/20240129-x1e80100-dts-missing-nodes-v6-6-2c0e691cfa3b@linaro.orgSigned-off-by: Bjorn Andersson <andersson@kernel.org>

Add the TCSR clock controller and register space node.
Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20240129-x1e80100-dts-missing-nodes-v6-5-2c0e691cfa3b@linaro.orgSigned-off-by: Bjorn Andersson <andersson@kernel.org>

Add ADSP and CDSP remoteproc nodes on X1E80100 platforms.
Signed-off-by: Sibi Sankar <quic_sibis@quicinc.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
Link: https://lore.kernel.org/r/20240129-x1e80100-dts-missing-nodes-v6-4-2c0e691cfa3b@linaro.orgSigned-off-by: Bjorn Andersson <andersson@kernel.org>

Add a node for the QMP AOSS.
Signed-off-by: Sibi Sankar <quic_sibis@quicinc.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
Link: https://lore.kernel.org/r/20240129-x1e80100-dts-missing-nodes-v6-3-2c0e691cfa3b@linaro.orgSigned-off-by: Bjorn Andersson <andersson@kernel.org>

SMP2P is used for interrupting and being interrupted about remoteproc
state changes related to the audio, compute and sensor subsystems.
Signed-off-by: Sibi Sankar <quic_sibis@quicinc.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
Link: https://lore.kernel.org/r/20240129-x1e80100-dts-missing-nodes-v6-2-2c0e691cfa3b@linaro.orgSigned-off-by: Bjorn Andersson <andersson@kernel.org>

Add the IPCC node, used to send and receive IPC signals with
remoteprocs.
Signed-off-by: Sibi Sankar <quic_sibis@quicinc.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
Link: https://lore.kernel.org/r/20240129-x1e80100-dts-missing-nodes-v6-1-2c0e691cfa3b@linaro.orgSigned-off-by: Bjorn Andersson <andersson@kernel.org>

Merge the X1E clock binding topic branch, to gain access to the many
clock defines.

Add bindings documentation for the X1E80100 Camera Clock Controller.
Signed-off-by: Rajendra Nayak <quic_rjendra@quicinc.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
Link: https://lore.kernel.org/r/20240202-x1e80100-clock-controllers-v4-5-7fb08c861c7c@linaro.orgSigned-off-by: Bjorn Andersson <andersson@kernel.org>

Add bindings documentation for the X1E80100 TCSR Clock Controller.
Co-developed-by: Rajendra Nayak <quic_rjendra@quicinc.com>
Signed-off-by: Rajendra Nayak <quic_rjendra@quicinc.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
Link: https://lore.kernel.org/r/20240202-x1e80100-clock-controllers-v4-4-7fb08c861c7c@linaro.orgSigned-off-by: Bjorn Andersson <andersson@kernel.org>

Add bindings documentation for the X1E80100 Graphics Clock Controller.
Signed-off-by: Rajendra Nayak <quic_rjendra@quicinc.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
Link: https://lore.kernel.org/r/20240202-x1e80100-clock-controllers-v4-3-7fb08c861c7c@linaro.orgSigned-off-by: Bjorn Andersson <andersson@kernel.org>

Add bindings documentation for the X1E80100 Display Clock Controller.
Signed-off-by: Rajendra Nayak <quic_rjendra@quicinc.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
Link: https://lore.kernel.org/r/20240202-x1e80100-clock-controllers-v4-2-7fb08c861c7c@linaro.orgSigned-off-by: Bjorn Andersson <andersson@kernel.org>

The block is the same between these platforms, at least from devicetree
point of view. So drop the dedicated schema and use the SM8550 one instead.
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
Link: https://lore.kernel.org/r/20240202-x1e80100-clock-controllers-v4-1-7fb08c861c7c@linaro.orgSigned-off-by: Bjorn Andersson <andersson@kernel.org>

New memory map layout changes (by Qualcomm firmware) have brought
in updates to base addresses and/or size for different memory regions
like cpcucp_fw, tz-stat, and also introduces new memory regions for
resource manager firmware. The updated memory map also fixes existing
issues pertaining to boot up failure while running memtest, thus
improving stability.

This change brings in these corresponding memory map updates to the
device tree for SA8775P SoC platform, which currently is in its
development stage.
Signed-off-by: Ninad Naik <quic_ninanaik@quicinc.com>
Tested-by: Eric Chanudet <echanude@redhat.com> # sa8775p-ride
Link: https://lore.kernel.org/r/20240125055134.7015-1-quic_ninanaik@quicinc.comSigned-off-by: Bjorn Andersson <andersson@kernel.org>

Include PM7250B PMIC for qcm6490-idp.
Signed-off-by: Umang Chheda <quic_uchheda@quicinc.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20240125115300.3496783-1-quic_uchheda@quicinc.comSigned-off-by: Bjorn Andersson <andersson@kernel.org>