There is no way in ACPI to tell in which speed the host controller is
supposed to run, so we default to fast mode (400KHz). Since this has been
the default all the time there should be no functional changes with this
change.

This is the first step required to refactor the driver probe so that we can
supply source clock from ACPI part of the driver to the core.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

Add I2C bus driver for the controller found in the LSI Axxia family SoCs. The
driver implements 10-bit addressing and SMBus transfer modes via emulation
(including SMBus block data read).
Signed-off-by: Anders Berg <anders.berg@avagotech.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

The HSI2C module on Exynos7 differs in the transfer status
bits. Transfer status bits were moved to INT_ENABLE and
INT_STATUS registers

This patch adds support for the HSI2C module on Exynos7.
1. Implementes a "hw" field in the variant struct to distinguish
   the hardware.
2. Updates the dt-new compatible in dt-binding documenation
Signed-off-by: Naveen Krishna Chatradhi <ch.naveen@samsung.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

i2cdetect scanned i2c bus slow because the i2c-mxs driver ignored the
NO_SLAVE_ACK bit during busy-waiting loop. Thanks to the patch, the
speedup happens.
Signed-off-by: Janusz Uzycki <j.uzycki@elproma.com.pl>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

In <https://lkml.org/lkml/2014/6/10/265> pointed out that the 10-bit
flag in the cros_ec_tunnel was useless.  It went into a 16-bit flags
field but was defined at (1 << 16).

Since we have no 10-bit i2c devices on the other side of the tunnel on
any known devices this was never a problem.  Until we do it makes
sense to remove this code.  On the EC side the code to handle this
flag was removed in <https://chromium-review.googlesource.com/204162>.
Reported-by: Dave Jones <davej@redhat.com>
Signed-off-by: Doug Anderson <dianders@chromium.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

To enable the cros-ec-tunnel driver to be auto-loaded when build as a
module add an of match table (and export it) to match the modalias
information passed on to userspace as the Cros EC MFD driver registers
the MFD subdevices with an of_compatibility string.
Signed-off-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
Reviewed-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

gcc rightfully says:

drivers/i2c/busses/i2c-rcar.c:198:10: warning: comparison between signed and unsigned integer expressions [-Wsign-compare]
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

Software is allowed to allocate number of descriptor size from 2 to 256,
this i2c controller could process more descriptor, but for i2c core soft
ware layer, only one i2c transaction is allowed each time.

So here switch to minimum 2 descriptor when initialization.
Signed-off-by: Fan Du <fan.du@intel.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

According to the i.mx spec, for multimaster mode, if I2C is
enabled when the bus is busy and asserts start, hardware inhibits
the transmission, clears MSTA without signaling a stop, generate
an interrupt, and set I2C_I2SR[IAL] to indicate a failed attempt
to engage the bus, which means arbitration lost. In this case,
we should first test I2C_I2SR[IAL], and clear this bit if it is
set, and then I2C controller default to slave receive mode.

This patch check the IAL bit every time before an I2c transmission.
if IAL is set, clear it and make I2C controller to default mode.
Signed-off-by: Haibo Chen <haibo.chen@freescale.com>
Acked-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

Having a transfer more than 32 bits is not all that unlikely.  Remove
the annotation.

The unlikely in the IRQ handler can't gain us much.  It's not in a
loop, so at most it would save 1 instruction per IRQ, which isn't
much.  In fact on the compiler I tested it produced the exact same
code.  Remove it too.
Suggested-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

Check if the ICMSR register (masked with the ICMIER register) evaluates to 0  in
the driver's interrupt handler and return IRQ_NONE in that case, like many other
drivers do.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

rcar_i2c_prepare_msg() always returns 0, so we can make this function return
*void* and thus remove the result check in rcar_i2c_master_xfer().
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

rcar_i2c_master_xfer() needlessly compares the message pointers (using indirect
addressing) in order to detect the last I2C message, while it's enough to only
compare the message indexes.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

Use the platform data to set the clk_freq when there is no DT configuration
available. The clk_freq in turn will determine the I2C speed mode.

In Quark, there is currently no other configuration mechanism other than
board files.
Signed-off-by: Raymond Tan <raymond.tan@intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Hock Leong Kweh <hock.leong.kweh@intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

Some legacy devices support ony I2C standard mode at 100kHz.
This patch allows to select the standard mode through the DTS
with the use of the existing clock-frequency parameter.

When clock-frequency parameter is not set, the fast mode is selected.
Only when the parameter is set at 100000, the standard mode is selected.
Signed-off-by: Romain Baeriswyl <romainba@abilis.com>
Reviewed-by: Christian Ruppert <christian.ruppert@abilis.com>
Acked-by: Alan Tull <atull@opensource.altera.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

Pull slave-dmaengine fixes from Vinod Koul:
 "Two small fixes for omap dmaengine driver which fixes cyclic suspend
  and resume"

* 'fixes' of git://git.infradead.org/users/vkoul/slave-dma:
  dmaengine: omap-dma: Restore the CLINK_CTRL in resume path
  dmaengine: omap-dma: Add memory barrier to dma_resume path

Pull vfs fixes from Al Viro:
 "Assorted fixes + unifying __d_move() and __d_materialise_dentry() +
  minimal regression fix for d_path() of victims of overwriting rename()
  ported on top of that"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
  vfs: Don't exchange "short" filenames unconditionally.
  fold swapping ->d_name.hash into switch_names()
  fold unlocking the children into dentry_unlock_parents_for_move()
  kill __d_materialise_dentry()
  __d_materialise_dentry(): flip the order of arguments
  __d_move(): fold manipulations with ->d_child/->d_subdirs
  don't open-code d_rehash() in d_materialise_unique()
  pull rehashing and unlocking the target dentry into __d_materialise_dentry()
  ufs: deal with nfsd/iget races
  fuse: honour max_read and max_write in direct_io mode
  shmem: fix nlink for rename overwrite directory

Pull cgroup fixes from Tejun Heo:
 "This is quite late but these need to be backported anyway.

  This is the fix for a long-standing cpuset bug which existed from
  2009.  cpuset makes use of PF_SPREAD_{PAGE|SLAB} flags to modify the
  task's memory allocation behavior according to the settings of the
  cpuset it belongs to; unfortunately, when those flags have to be
  changed, cpuset did so directly even whlie the target task is running,
  which is obviously racy as task->flags may be modified by the task
  itself at any time.  This obscure bug manifested as corrupt
  PF_USED_MATH flag leading to a weird crash.

  The bug is fixed by moving the flag to task->atomic_flags.  The first
  two are prepatory ones to help defining atomic_flags accessors and the
  third one is the actual fix"

* 'for-3.17-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/cgroup:
  cpuset: PF_SPREAD_PAGE and PF_SPREAD_SLAB should be atomic flags
  sched: add macros to define bitops for task atomic flags
  sched: fix confusing PFA_NO_NEW_PRIVS constant

Pull ARM SoC fixes from Olof Johansson:
 "Here's our last set of fixes for 3.17.  Most of these are for TI
  platforms, fixing some noisy Kconfig issues, runtime clock and power
  issues on several platforms and NAND timings on DRA7.

  There are also a couple of bug fixes for i.MX, one for QCOM and a
 small fix to avoid section mismatch noise on PXA.

  Diffstat looks large, partially due to some tables being updated and
  thus touching many lines.  The qcom gsbi change also restructures
  clock management a bit and thus touches a bunch of lines.

  All in all, a bit more changes than we'd like at this point, but
  nothing stands out as risky either so it seems like the right thing to
  send it up now instead of holding it to the merge window"

* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
  drivers/soc: qcom: do not disable the iface clock in probe
  ARM: imx: fix .is_enabled() of shared gate clock
  ARM: OMAP3: Fix I/O chain clock line assertion timed out error
  ARM: keystone: dts: fix bindings for pcie and usb clock nodes
  bus: omap_l3_noc: Fix connID for OMAP4
  ARM: DT: imx53: fix lvds channel 1 port
  ARM: dts: cm-t54: fix serial console power supply.
  ARM: dts: dra7-evm: Fix NAND GPMC timings
  ARM: pxa: fix section mismatch warning for pxa_timer_nodt_init
  ARM: OMAP: Fix Kconfig warning for omap1

Pull MIPS fixes from Ralf Baechle:
 "The final round of fixes.  One corner case in the math emulator and
  another one in the mcount function for ftrace"

* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus:
  MIPS: mcount: Adjust stack pointer for static trace in MIPS32
  MIPS: Fix MFC1 & MFHC1 emulation for 64-bit MIPS systems

Pull x86 fixes from Ingo Molnar:
 "This has:

   - EFI revert to fix a boot regression
   - early_ioremap() fix for boot failure
   - KASLR fix for possible boot failures
   - EFI fix for corrupted string printing
   - remove a misleading EFI bootup 'failed!' error message

  Unfortunately it's all rather close to the merge window"

* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/efi: Truncate 64-bit values when calling 32-bit OutputString()
  x86/efi: Delete misleading efi_printk() error message
  Revert "efi/x86: efistub: Move shared dependencies to <asm/efi.h>"
  x86/kaslr: Avoid the setup_data area when picking location
  x86 early_ioremap: Increase FIX_BTMAPS_SLOTS to 8

Only exchange source and destination filenames
if flags contain RENAME_EXCHANGE.
In case if executable file was running and replaced by
other file /proc/PID/exe should still show correct file name,
not the old name of the file by which it was replaced.

The scenario when this bug manifests itself was like this:
* ALT Linux uses rpm and start-stop-daemon;
* during a package upgrade rpm creates a temporary file
  for an executable to rename it upon successful unpacking;
* start-stop-daemon is run subsequently and it obtains
  the (nonexistant) temporary filename via /proc/PID/exe
  thus failing to identify the running process.

Note that "long" filenames (> DNAiME_INLINE_LEN) are still
exchanged without RENAME_EXCHANGE and this behaviour exists
long enough (should be fixed too apparently).
So this patch is just an interim workaround that restores
behavior for "short" names as it was before changes
introduced by commit da1ce067 ("vfs: add cross-rename").

See https://lkml.org/lkml/2014/9/7/6 for details.

AV: the comments about being more careful with ->d_name.hash
than with ->d_name.name are from back in 2.3.40s; they
became obsolete by 2.3.60s, when we started to unhash the
target instead of swapping hash chain positions followed
by d_delete() as we used to do when dcache was first
introduced.
Acked-by: Miklos Szeredi <mszeredi@suse.cz>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Alexander Viro <viro@zeniv.linux.org.uk>
Cc: linux-fsdevel@vger.kernel.org
Cc: stable@vger.kernel.org
Fixes: da1ce067 "vfs: add cross-rename"
Signed-off-by: Mikhail Efremov <sem@altlinux.org>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>

and do it along with ->d_name.len there
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>

... renaming it into dentry_unlock_for_move() and making it more
symmetric with dentry_lock_for_move().
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>

it folds into __d_move() now
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>

... thus making it much closer to (now unreachable, BTW) IS_ROOT(dentry)
case in __d_move().  A bit more and it'll fold in.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>

list_del() + list_add() is a slightly pessimised list_move()
list_del() + INIT_LIST_HEAD() is a slightly pessimised list_del_init()

Interleaving those makes the resulting code even worse.  And harder to follow...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>

... and get rid of duplicate BUG_ON() there
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>

Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>

Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>

The third argument of fuse_get_user_pages() "nbytesp" refers to the number of
bytes a caller asked to pack into fuse request. This value may be lesser
than capacity of fuse request or iov_iter.  So fuse_get_user_pages() must
ensure that *nbytesp won't grow.

Now, when helper iov_iter_get_pages() performs all hard work of extracting
pages from iov_iter, it can be done by passing properly calculated
"maxsize" to the helper.

The other caller of iov_iter_get_pages() (dio_refill_pages()) doesn't need
this capability, so pass LONG_MAX as the maxsize argument here.

Fixes: c9c37e2e ("fuse: switch to iov_iter_get_pages()")
Reported-by: Werner Baumann <werner.baumann@onlinehome.de>
Tested-by: Maxim Patlasov <mpatlasov@parallels.com>
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>

If overwriting an empty directory with rename, then need to drop the extra
nlink.

Test prog:

#include <stdio.h>
#include <fcntl.h>
#include <err.h>
#include <sys/stat.h>

int main(void)
{
	const char *test_dir1 = "test-dir1";
	const char *test_dir2 = "test-dir2";
	int res;
	int fd;
	struct stat statbuf;

	res = mkdir(test_dir1, 0777);
	if (res == -1)
		err(1, "mkdir(\"%s\")", test_dir1);

	res = mkdir(test_dir2, 0777);
	if (res == -1)
		err(1, "mkdir(\"%s\")", test_dir2);

	fd = open(test_dir2, O_RDONLY);
	if (fd == -1)
		err(1, "open(\"%s\")", test_dir2);

	res = rename(test_dir1, test_dir2);
	if (res == -1)
		err(1, "rename(\"%s\", \"%s\")", test_dir1, test_dir2);

	res = fstat(fd, &statbuf);
	if (res == -1)
		err(1, "fstat(%i)", fd);

	if (statbuf.st_nlink != 0) {
		fprintf(stderr, "nlink is %lu, should be 0\n", statbuf.st_nlink);
		return 1;
	}

	return 0;
}
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
Cc: stable@vger.kernel.org
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>

Pull input fix from Dmitry Torokhov:
 "A small fixup to i8042 adding Asus X450LCP to the nomux list"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
  Input: i8042 - fix Asus X450LCP touchpad detection

Pull scheduler fixes from Ingo Molnar:
 "A CONFIG_STACK_GROWSUP=y fix, and a hotplug llc CPU mask fix"

* 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  sched: Fix unreleased llc_shared_mask bit during CPU hotplug
  sched: Fix end_of_stack() and location of stack canary for architectures using CONFIG_STACK_GROWSUP

Merge fixes from Andrew Morton:
 "9 fixes"

* emailed patches from Andrew Morton <akpm@linux-foundation.org>:
  mm: softdirty: keep bit when zapping file pte
  fs/cachefiles: add missing \n to kerror conversions
  genalloc: fix device node resource counter
  drivers/rtc/rtc-efi.c: add missing module alias
  mm, slab: initialize object alignment on cache creation
  mm: softdirty: addresses before VMAs in PTE holes aren't softdirty
  ocfs2/dlm: do not get resource spinlock if lockres is new
  nilfs2: fix data loss with mmap()
  ocfs2: free vol_label in ocfs2_delete_osb()

This fixes the same bug as b43790ee ("mm: softdirty: don't forget to
save file map softdiry bit on unmap") and 9aed8614 ("mm/memory.c:
don't forget to set softdirty on file mapped fault") where the return
value of pte_*mksoft_dirty was being ignored.

To be sure that no other pte/pmd "mk" function return values were being
ignored, I annotated the functions in arch/x86/include/asm/pgtable.h
with __must_check and rebuilt.

The userspace effect of this bug is that the softdirty mark might be
lost if a file mapped pte get zapped.
Signed-off-by: Peter Feiner <pfeiner@google.com>
Acked-by: Cyrill Gorcunov <gorcunov@openvz.org>
Cc: Pavel Emelyanov <xemul@parallels.com>
Cc: Jamie Liu <jamieliu@google.com>
Cc: Hugh Dickins <hughd@google.com>
Cc: <stable@vger.kernel.org>	[3.12+]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Commit 0227d6ab ("fs/cachefiles: replace kerror by pr_err") didn't
include newline featuring in original kerror definition
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Reported-by: David Howells <dhowells@redhat.com>
Acked-by: David Howells <dhowells@redhat.com>
Cc: <stable@vger.kernel.org>	[3.16.x]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Decrement the np_pool device_node refcount, which was incremented on
the preceding of_parse_phandle() call.
Signed-off-by: Vladimir Zapolskiy <vladimir_zapolskiy@mentor.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Olof Johansson <olof@lixom.net>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Without proper alias kernel module is not loaded for rtc-efi driver.
Signed-off-by: Pali Rohár <pali.rohar@gmail.com>
Cc: dann frazier <dannf@dannf.org>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>