Add bindings documentation for Sunplus SP7021 SoC.
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Wells Lu <wellslutw@gmail.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>

Gerhard Engleder says:

====================
ptp: Support hardware clocks with additional free running cycle counter

ptp vclocks require a clock with free running time for the timecounter.
Currently only a physical clock forced to free running is supported.
If vclocks are used, then the physical clock cannot be synchronized
anymore. The synchronized time is not available in hardware in this
case. As a result, timed transmission with TAPRIO hardware support
is not possible anymore.

If hardware would support a free running time additionally to the
physical clock, then the physical clock does not need to be forced to
free running. Thus, the physical clocks can still be synchronized while
vclocks are in use.

The physical clock could be used to synchronize the time domain of the
TSN network and trigger TAPRIO. In parallel vclocks can be used to
synchronize other time domains.

One year ago I thought for two time domains within a TSN network also
two physical clocks are required. This would lead to new kernel
interfaces for asking for the second clock, ... . But actually for a
time triggered system like TSN there can be only one time domain that
controls the system itself. All other time domains belong to other
layers, but not to the time triggered system itself. So other time
domains can be based on a free running counter if similar mechanisms
like 2 step synchroisation are used.

Synchronisation was tested with two time domains between two directly
connected hosts. Each host run two ptp4l instances, the first used the
physical clock and the second used the virtual clock. I used my FPGA
based network controller as network device. ptp4l was used in
combination with the virtual clock support patches from Miroslav
Lichvar.

v4:
- if_index of 0 is invalid (Jonathan Lemon)
- set if_index to 0 in the SOF_TIMESTAMPING_RAW_HARDWARE block (Jonathan
  Lemon)
- add helper function for netdev_get_tstamp() call (Jonathan Lemon)
- update SKBTX_ANY_TSTAMP (Paolo Abeni)
- use separate bits for new tx_flags (Richard Cochran)

v3:
- optimize ptp_convert_timestamp (Richard Cochran)
- call dev_get_by_napi_id() only if needed (Richard Cochran)
- use non-negated logical test (Richard Cochran)
- add comment for skipped output (Richard Cochran)
- add comment for SKBTX_HW_TSTAMP_USE_CYCLES masking (Richard Cochran)

v2:
- rename ptp_clock cycles to has_cycles (Richard Cochran)
- call it free running cycle counter (Richard Cochran)
- update struct skb_shared_hwtstamps kdoc (Richard Cochran)
- optimize timestamp address/cookie processing path (Richard Cochran,
  Vinicius Costa Gomes)

v1:
- complete rework based on suggestions (Richard Cochran)
====================

Link: https://lore.kernel.org/r/20220506200142.3329-1-gerhard@engleder-embedded.comSigned-off-by: Paolo Abeni <pabeni@redhat.com>

The TSN endpoint Ethernet MAC supports a free running counter
additionally to its clock. This free running counter can be read and
hardware timestamps are supported. As the name implies, this counter
cannot be set and its frequency cannot be adjusted.

Add free running cycle counter support based on this free running
counter to physical clock. This also requires hardware time stamps
based on that free running counter.
Signed-off-by: Gerhard Engleder <gerhard@engleder-embedded.com>
Acked-by: Jonathan Lemon <jonathan.lemon@gmail.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>

ptp_convert_timestamp() is called in the RX path of network messages.
The current implementation takes ~5000ns on 1.2GHz A53. This is too much
for the hot path of packet processing.

Introduce hash table for fast vclock lookup in ptp_convert_timestamp().
The execution time of ptp_convert_timestamp() is reduced to ~700ns on
1.2GHz A53.
Signed-off-by: Gerhard Engleder <gerhard@engleder-embedded.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>

If a physical clock supports a free running cycle counter, then
timestamps shall be based on this time too. For TX it is known in
advance before the transmission if a timestamp based on the free running
cycle counter is needed. For RX it is impossible to know which timestamp
is needed before the packet is received and assigned to a socket.

Support late timestamp determination by a network device. Therefore, an
address/cookie is stored within the new netdev_data field of struct
skb_shared_hwtstamps. This address/cookie is provided to a new network
device function called ndo_get_tstamp(), which returns a timestamp based
on the normal/adjustable time or based on the free running cycle
counter. If function is not supported, then timestamp handling is not
changed.

This mechanism is intended for RX, but TX use is also possible.
Signed-off-by: Gerhard Engleder <gerhard@engleder-embedded.com>
Acked-by: Jonathan Lemon <jonathan.lemon@gmail.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>

ptp_convert_timestamp() converts only the timestamp hwtstamp, which is
a field of the argument with the type struct skb_shared_hwtstamps *. So
a pointer to the hwtstamp field of this structure is sufficient.

Rework ptp_convert_timestamp() to use an argument of type ktime_t *.
This allows to add additional timestamp manipulation stages before the
call of ptp_convert_timestamp().
Signed-off-by: Gerhard Engleder <gerhard@engleder-embedded.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>

The free running cycle counter of physical clocks called cycles shall be
used for hardware timestamps to enable synchronisation.

Introduce new flag SKBTX_HW_TSTAMP_USE_CYCLES, which signals driver to
provide a TX timestamp based on cycles if cycles are supported.
Signed-off-by: Gerhard Engleder <gerhard@engleder-embedded.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>

ptp vclocks require a free running time for their timecounter.
Currently only a physical clock forced to free running is supported.
If vclocks are used, then the physical clock cannot be synchronized
anymore. The synchronized time is not available in hardware in this
case. As a result, timed transmission with TAPRIO hardware support
is not possible anymore.

If hardware would support a free running time additionally to the
physical clock, then the physical clock does not need to be forced to
free running. Thus, the physical clocks can still be synchronized
while vclocks are in use.

The physical clock could be used to synchronize the time domain of the
TSN network and trigger TAPRIO. In parallel vclocks can be used to
synchronize other time domains.

Introduce support for a free running cycle counter called cycles to
physical clocks. Rework ptp vclocks to use this free running cycle
counter. Default implementation is based on time of physical clock.
Thus, behavior of ptp vclocks based on physical clocks without free
running cycle counter is identical to previous behavior.
Signed-off-by: Gerhard Engleder <gerhard@engleder-embedded.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>

Since commit 4e30e98c ("dpaa2-mac: return -EPROBE_DEFER from dpaa2_mac_open in case the fwnode is not set")
@parent can't be NULL after the if. It's either the address
of the ->fwnode of @dpmacs or @fwnode in case of ACPI.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Link: https://lore.kernel.org/r/20220506200029.852310-1-kuba@kernel.orgSigned-off-by: Paolo Abeni <pabeni@redhat.com>

Simon Horman says:

====================
nfp: support Corigine PCIE vendor ID

Historically the nfp driver has supported NFP chips with Netronome's
PCIE vendor ID. This patch extends the driver to also support NFP
chips, which at this point are assumed to be otherwise identical from
a software perspective, that have Corigine's PCIE vendor ID (0x1da8).

This patchset begins by cleaning up strings to make them:
* Vendor neutral for the NFP chip
* Relate to Corigine for the driver itself

It then adds support to the driver for the Corigine's PCIE vendor ID
====================

Link: https://lore.kernel.org/r/20220508173816.476357-1-simon.horman@corigine.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Historically the nfp driver has supported NFP chips with Netronome's
PCIE vendor ID. This patch extends the driver to also support NFP
chips, which at this point are assumed to be otherwise identical from
a software perspective, that have Corigine's PCIE vendor ID (0x1da8).

Also, Rename the macro definitions PCI_DEVICE_ID_NERTONEOME_NFPXXXX
to PCI_DEVICE_ID_NFPXXXX, as they are now used in conjunction with two
PCIE vendor IDs.
Signed-off-by: Yu Xiao <yu.xiao@corigine.com>
Signed-off-by: Yinjun Zhang <yinjun.zhang@corigine.com>
Signed-off-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Historically the nfp driver has supported NFP chips with Netronome's
PCIE vendor ID. In preparation for extending the to also support NFP
chips that have Corigine's PCIE vendor ID (0x1da8) make printk statements
relating to the chip vendor neutral.

An alternate approach is to set the string based on the PCI vendor ID.
In our judgement this proved to cumbersome so we have taken this simpler
approach.

Update strings relating to the driver to use Corigine, who have taken
over maintenance of the driver.
Signed-off-by: Yu Xiao <yu.xiao@corigine.com>
Signed-off-by: Yinjun Zhang <yinjun.zhang@corigine.com>
Signed-off-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Tony Nguyen says:

====================
100GbE Intel Wired LAN Driver Updates 2022-05-06

Marcin Szycik says:

This patchset adds support for systemd defined naming scheme for port
representors, as well as re-enables displaying PCI bus-info in ethtool.

bus-info information has previously been removed from ethtool for port
representors, as a workaround for a bug in lshw tool, where the tool would
sometimes display wrong descriptions for port representors/PF. Now the bug
has been fixed in lshw tool [1].

Removing the workaround can be considered a regression (user might be
running an older, unpatched version of lshw) (see [2] for discussion).
However, calling SET_NETDEV_DEV also produces the same effect as removing
the workaround, i.e. lshw is able to access PCI bus-info (this time not
via ethtool, but in some other way) and the bug can occur.

Adding SET_NETDEV_DEV is important, as it greatly improves netdev naming -
- port representors are named based on PF name. Currently port representors
are named "ethX", which might be confusing, especially when spawning VFs on
multiple PFs. Furthermore, it's currently harder to determine to which PF
does a particular port representor belong, as bus-info is not shown in
ethtool.

Consider the following three cases:

Case 1: current code - driver workaround in place, no SET_NETDEV_DEV,
lshw with or without fix. Port representors are not displayed because they
don't have bus-info (the workaround), PFs are labelled correctly:

$ sudo ./lshw -c net -businfo
Bus info          Device      Class          Description
========================================================
pci@0000:02:00.0  ens6f0      network        Ethernet Controller E810-XXV for SFP <-- PF
pci@0000:02:00.1  ens6f1      network        Ethernet Controller E810-XXV for SFP
pci@0000:02:01.0  ens6f0v0    network        Ethernet Adaptive Virtual Function <-- VF
pci@0000:02:01.1  ens6f0v1    network        Ethernet Adaptive Virtual Function
...

Case 2: driver workaround in place, SET_NETDEV_DEV, no lshw fix. Port
representors have predictable names. lshw is able to get bus-info because
of SET_NETDEV_DEV and netdevs CAN be mislabelled:

$ sudo ./lshw -c net -businfo
Bus info          Device           Class          Description
=============================================================
pci@0000:02:00.0  ens6f0npf0vf60   network        Ethernet Controller E810-XXV for SFP <-- mislabeled port representor
pci@0000:02:00.1  ens6f1           network        Ethernet Controller E810-XXV for SFP
pci@0000:02:01.0  ens6f0v0         network        Ethernet Adaptive Virtual Function
pci@0000:02:01.1  ens6f0v1         network        Ethernet Adaptive Virtual Function
...
pci@0000:02:00.0  ens6f0npf0vf26   network        Ethernet interface
pci@0000:02:00.0  ens6f0           network        Ethernet interface <-- mislabeled PF
pci@0000:02:00.0  ens6f0npf0vf81   network        Ethernet interface
...
$ sudo ethtool -i ens6f0npf0vf60
driver: ice
...
bus-info:
...

Output of lshw would be the same with workaround removed; it does not
change the fact that lshw labels netdevs incorrectly, while at the same
time it prevents ethtool from displaying potentially useful data
(bus-info).

Case 3: workaround removed, SET_NETDEV_DEV, lshw fix:

$ sudo ./lshw -c net -businfo
Bus info          Device           Class          Description
=============================================================
pci@0000:02:00.0  ens6f0npf0vf73   network        Ethernet Controller E810-XXV for SFP
pci@0000:02:00.1  ens6f1           network        Ethernet Controller E810-XXV for SFP
pci@0000:02:01.0  ens6f0v0         network        Ethernet Adaptive Virtual Function
pci@0000:02:01.1  ens6f0v1         network        Ethernet Adaptive Virtual Function
...
pci@0000:02:00.0  ens6f0npf0vf5    network        Ethernet Controller E810-XXV for SFP
pci@0000:02:00.0  ens6f0           network        Ethernet Controller E810-XXV for SFP
pci@0000:02:00.0  ens6f0npf0vf60   network        Ethernet Controller E810-XXV for SFP
...
$ sudo ethtool -i ens6f0npf0vf73
driver: ice
...
bus-info: 0000:02:00.0
...

In this case poort representors have predictable names, netdevs are not
mislabelled in lshw, and bus-info is shown in ethtool.

[1] https://ezix.org/src/pkg/lshw/commit/9bf4e4c9c1
[2] https://patchwork.ozlabs.org/project/intel-wired-lan/patch/20220321144731.3935-1-marcin.szycik@linux.intel.com

* '100GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/next-queue:
  Revert "ice: Hide bus-info in ethtool for PRs in switchdev mode"
  ice: link representors to PCI device
====================

Link: https://lore.kernel.org/r/20220506180052.5256-1-anthony.l.nguyen@intel.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Eliminate the follow smatch warning:

net/rose/rose_route.c:1136 rose_node_show() warn: inconsistent
indenting.
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Signed-off-by: Jiapeng Chong <jiapeng.chong@linux.alibaba.com>
Link: https://lore.kernel.org/r/20220507034207.18651-1-jiapeng.chong@linux.alibaba.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Guangbin Huang says:

====================
net: hns3: updates for -next

This series includes some updates for the HNS3 ethernet driver.

Change logs:
V1 -> V2:
 - Fix some sparse warnings of patch 3# and 4#.
 - Add patch #6 to fix sparse warnings of incorrect type of argument.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

The argument rss_ind_tbl_size is type u16 in function definition of
hclge_comm_get_rss_indir_tbl(), but it is set to type __le16 in function
declaration by mistake, so fix it.
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch adds a new mailbox opcode to query map relation between
vf ring and vector.
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch uses __le16/__32 to define mailbox data structures. Then byte
order conversion are added for mailbox messages from VF to PF.
Signed-off-by: Jie Wang <wangjie125@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Currently, hns3 mailbox processing between PF and VF missed to convert
message byte order and use data type u16 instead of __le16 for mailbox
data process. These processes may cause problems between different
architectures.

So this patch uses __le16/__le32 data type to define mailbox data
structures. To be compatible with old hns3 driver, these structures use
one-byte alignment. Then byte order conversions are added to mailbox
messages from PF to VF.
Signed-off-by: Jie Wang <wangjie125@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Vector0 is used for common interrupt control events and is
irrelevant to performance. Currently, the driver sets the
default affinity of vector0 to NUMA nodes, which is unnecessary.
Therefore, the default setting is removed, and the driver does
not set the affinity for vector0.
Signed-off-by: Yufeng Mo <moyufeng@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When set tx-buf-size as 0 by ethtool, hns3_init_tx_spare_buffer()
will return directly and priv->ring->tx_spare->len is uninitialized,
then print function access priv->ring->tx_spare->len will cause
this issue.

When set tx-buf-size as 0 by ethtool, the print function will
print 0 directly and not access priv->ring->tx_spare->len.

Fixes: 2373b35c ("net: hns3: add log for setting tx spare buf size")
Signed-off-by: Hao Chen <chenhao288@hisilicon.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Yuiko Oshino says:

====================
net: phy: add LAN8742 phy support

add LAN8742 phy support
update LAN88xx phy ID and phy ID mask so that it can coexist with LAN8742

The current phy IDs on the available hardware.
    LAN8742 0x0007C130, 0x0007C131
    LAN88xx 0x0007C132

v3->v4:
- fixed the one tab missing issue in the smsc.c.

v2->v3:
-added comments about the 0xfffffff2 mask that is for the differentiation and the future revisions.

v1->v2:
-removed "REVIEW REQUEST3" from the PATCH 1/2.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

The current phy IDs on the available hardware.
        LAN8742 0x0007C130, 0x0007C131
Signed-off-by: Yuiko Oshino <yuiko.oshino@microchip.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

update LAN88xx phy ID and phy ID mask because the existing code conflicts with the LAN8742 phy.

The current phy IDs on the available hardware.
        LAN8742 0x0007C130, 0x0007C131
        LAN88xx 0x0007C132
Signed-off-by: Yuiko Oshino <yuiko.oshino@microchip.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

Oleksij Rempel says:

====================
add ti dp83td510 support

changes v4:
- dp83td510: remove unused variables
- s/base1/baset1
- s/genphy_c45_baset1_read_master_slave/genphy_c45_pma_baset1_read_master_slave

changes v3:
- export reusable code snippets and make use of it in the dp83td510
  driver

changes v2:
- rewrite the driver reduce usage of common code and to reduce amount of
  quirks.
- add genphy_c45_baset1_an_config_aneg fix
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

The DP83TD510E is an ultra-low power Ethernet physical layer transceiver
that supports 10M single pair cable.

This driver was tested with NXP SJA1105, STMMAC and ASIX AX88772B USB Ethernet
controller.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

Export genphy_c45_baset1_read_status() to make it reusable by PHY drivers.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

Since MDIO_PMA_PMD_BT1_CTRL register shows actual configuration (and
forced state configuration is equal to the state), we should show
this configuration for ethtool.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

Move baset1 specific part of genphy_c45_read_pma() code to
separate function to make it reusable by PHY drivers.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

Do not change default master/slave forced configuration if no changes was
requested.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

Move baset1 specific part of genphy_c45_pma_setup_forced() code to
separate function to make it reusable by PHY drivers.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

Do not change default master/slave autoneg configuration if no
changes was requested.

Fixes: 3da8ffd8 ("net: phy: Add 10BASE-T1L support in phy-c45")
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

Alaa Mohamed says:

====================
propagate extack to vxlan_fdb_delete

In order to propagate extack to vxlan_fdb_delete and vxlan_fdb_parse,
add extack to .ndo_fdb_del and edit all fdb del handelers.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch adds extack msg support to vxlan_fdb_delete and vxlan_fdb_parse.
extack is used to propagate meaningful error msgs to the user of vxlan
fdb netlink api
Signed-off-by: Alaa Mohamed <eng.alaamohamedsoliman.am@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add extack support to .ndo_fdb_del in netdevice.h and
all related methods.
Signed-off-by: Alaa Mohamed <eng.alaamohamedsoliman.am@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Ricardo Martinez says:

====================
net: wwan: t7xx: PCIe driver for MediaTek M.2 modem

t7xx is the PCIe host device driver for Intel 5G 5000 M.2 solution which
is based on MediaTek's T700 modem to provide WWAN connectivity.
The driver uses the WWAN framework infrastructure to create the following
control ports and network interfaces:
* /dev/wwan0mbim0 - Interface conforming to the MBIM protocol.
  Applications like libmbim [1] or Modem Manager [2] from v1.16 onwards
  with [3][4] can use it to enable data communication towards WWAN.
* /dev/wwan0at0 - Interface that supports AT commands.
* wwan0 - Primary network interface for IP traffic.

The main blocks in t7xx driver are:
* PCIe layer - Implements probe, removal, and power management callbacks.
* Port-proxy - Provides a common interface to interact with different types
  of ports such as WWAN ports.
* Modem control & status monitor - Implements the entry point for modem
  initialization, reset and exit, as well as exception handling.
* CLDMA (Control Layer DMA) - Manages the HW used by the port layer to send
  control messages to the modem using MediaTek's CCCI (Cross-Core
  Communication Interface) protocol.
* DPMAIF (Data Plane Modem AP Interface) - Controls the HW that provides
  uplink and downlink queues for the data path. The data exchange takes
  place using circular buffers to share data buffer addresses and metadata
  to describe the packets.
* MHCCIF (Modem Host Cross-Core Interface) - Provides interrupt channels
  for bidirectional event notification such as handshake, exception, PM and
  port enumeration.

The compilation of the t7xx driver is enabled by the CONFIG_MTK_T7XX config
option which depends on CONFIG_WWAN.
This driver was originally developed by MediaTek. Intel adapted t7xx to
the WWAN framework, optimized and refactored the driver source code in close
collaboration with MediaTek. This will enable getting the t7xx driver on the
Approved Vendor List for interested OEM's and ODM's productization plans
with Intel 5G 5000 M.2 solution.

List of contributors:
Amir Hanania <amir.hanania@intel.com>
Andriy Shevchenko <andriy.shevchenko@linux.intel.com>
Chandrashekar Devegowda <chandrashekar.devegowda@intel.com>
Dinesh Sharma <dinesh.sharma@intel.com>
Eliot Lee <eliot.lee@intel.com>
Haijun Liu <haijun.liu@mediatek.com>
M Chetan Kumar <m.chetan.kumar@intel.com>
Mika Westerberg <mika.westerberg@linux.intel.com>
Moises Veleta <moises.veleta@intel.com>
Pierre-louis Bossart <pierre-louis.bossart@intel.com>
Chiranjeevi Rapolu <chiranjeevi.rapolu@intel.com>
Ricardo Martinez <ricardo.martinez@linux.intel.com>
Madhusmita Sahu <madhusmita.sahu@intel.com>
Muralidharan Sethuraman <muralidharan.sethuraman@intel.com>
Soumya Prakash Mishra <Soumya.Prakash.Mishra@intel.com>
Sreehari Kancharla <sreehari.kancharla@intel.com>
Suresh Nagaraj <suresh.nagaraj@intel.com>

[1] https://www.freedesktop.org/software/libmbim/
[2] https://www.freedesktop.org/software/ModemManager/
[3] https://gitlab.freedesktop.org/mobile-broadband/ModemManager/-/merge_requests/582
[4] https://gitlab.freedesktop.org/mobile-broadband/ModemManager/-/merge_requests/523

V8:
- Rebase skb_data_area_size() patch (02).

V7:
- Delete unused macros.
- Avoid duplicated calls to le32_to_cpu().
- Fix 'out of bounds' compilation error.
- Rename port_number to port_count.
- Remove '!!' when the destination variable is a boolean.
- Remove unneeded spinlock around rx_length_th.
- Remove common field from union inside dpmaif_drb struct.
- Use 'goto' for the exit flow in t7xx_pci_enable_sleep().
- Merge CLDMA tgpd and rgpd structs.
- Add comments to clarify skb consumption by ports.
- Introduce skb_data_area_size() helper.
- Declare the port config array as constant.
- Update CLDMA_JUMBO_BUFF_SZ definition when ccci_header
  is introduced by port-proxy patch.
- Update Reviewed-by tags.
- Simplify t7xx_dpmaif_tx_send_skb() and make t7xx_dpmaif_add_skb_to_ring()
  report the tx queue full state early.

V6:
- Remove unneeded initializations and bit masks.
- Remove t7xx_common.h file.
- Add comment to circular linking in GPD list.
- Use min instead of min_t.
- Use int for local indexes instead of short or char.
- Update the commit message in CLDMA patch about dependencies on core patch.
- Add space between contributor name and email address.
- Rename registers with double negatives
  e.g. DIS_ASPM_LOWPWR_CLR_0 -> ENABLE_ASPM_LOWPWR.
- Fix a race condition in pci sleep resource locking.
- Initialize interrupts with t7xx_pcie_mac_set_int() instead of 'clear'.
- Remove duplicate spin_lock_init(&md->exp_lock).
- Remove .ndo_select_queue callback due to singular TX queue.
- Remove call to deprecated netif_rx_any_context().
- Fix include guard name in t7xx_hif_dpmaif.h.
- Remove unused q_num parameter in DPMAIF functions.
- Do not serialize the drb_wr_idx write in t7xx_dpmaif_add_skb_to_ring()
  and the read from t7xx_txq_drb_wr_available().
- Fix potential leak in t7xx_dpmaif_add_skb_to_ring().
- Unionize:
    DRB structs: msg and pd.
    PIT structs: msg and pd.
- Replace list_head & spinlock with skb_buff_head in dpmaif_tx_queue.
- Remove rx_length_th check in TX WWAN port flow.
- Remove wwan_remove_port() from the critical section in WWAN port uninit.
- Use skb_end_pointer() to avoid conditional compilation.
- Simplify the loop in t7xx_port_ctrl_tx() by checking the buffer offset
  instead of calculating the number of required packets.
- Remove the code for unused channel PORT_CH_STATUS_RX.
- Remove bit flags from ports. Ports can check chan_enable instead of the
  PORT_F_RX_ALLOW_DROP flag.
- Use INVALID_SEQ_NUM to identify the first seq number.
- Rename port_static to port_conf and ports_private to ports.
- Implement t7xx_port_send_skb() and t7xx_port_send_ctl_skb() in a layered
  approach to reduce duplicated code and simplify the CCCI header handling.
- Move wwan_port_rx() call from port-proxy to WWAN port.
- Rename t7xx_port_recv_skb() to t7xx_port_enqueue_skb().
- Move control message parsing logic from port-proxy to control port,
  preserve the endianness when parsing the message and make port-proxy
  export a function to enable/disable ports.
- Use flexible arrays for:
    port-proxy ports.
    payload data in t7xx_fsm_event, port_msg, and mtk_runtime_feature.

v5:
- Update Intel's copyright years to 2021-2022.
- Remove circular dependency between DPMAIF HW (07) and HIF (08).
- Keep separate patches for CLDMA (02) and Core (03)
  but improve the code split by decoupling CLDMA from
  modem ops and cleaning up t7xx_common.h.
- Rename ID_CLDMA0/ID_CLDMA1 to CLDMA_ID_AP/CLDMA_ID_MD.
- Consistently use CLDMA's ring_lock to protect tr_ring.
- Free resources first and then print messages.
- Implement suggested name changes.
- Do not explicitly include dev_printk.h.
- Remove redundant dev_err()s.
- Fix possible memory leak during probe.
- Remove infrastructure for legacy interrupts.
- Remove unused macros and variables, including those that
  can be replaced with constants.
- Remove PCIE_MAC_MSIX_MSK_SET macro which is duplicated code.
- Refactor __t7xx_pci_pm_suspend() for clarity.
- Refactor t7xx_cldma_rx_ring_init() and t7xx_cldma_tx_ring_init().
- Do not use & for function callbacks.
- Declare a structure to access skb->cb[] data.
- Use skb_put_data instead of memcpy.
- No need to use kfree_sensitive.
- Use dev_kfree_skb() instead of kfree_skb().
- Refactor t7xx_prepare_device_rt_data() to remove potential leaks,
  avoid unneeded memset and keep rt_data and packet_size updates
  inside the same 'if' block.
- Set port's rx_length_th back to 0 during uninit.
- Remove unneeded 'blocking' parameter from t7xx_cldma_send_skb().
- Return -EIO in t7xx_cldma_send_skb() if the queue is inactive.
- Refactor t7xx_cldma_qs_are_active() to use pci_device_is_present().
- Simplify t7xx_cldma_stop_q() and rename it to t7xx_cldma_stop_all_qs().
- Fix potential leaks in t7xx_cldma_init().
- Improve error handling in fsm_append_event and fsm_routine_starting().
- Propagate return codes from fsm_append_cmd() and t7xx_fsm_append_event().
- Refactor fsm_wait_for_event() to avoid unnecessary sleep.
- Create the WWAN ports and net device only after the modem is in
  the ready state.
- Refactor t7xx_port_proxy_recv_skb() and port_recv_skb().
- Rename t7xx_port_check_rx_seq_num() as t7xx_port_next_rx_seq_num()
  and fix the seq_num logic to handle overflows.
- Declare seq_nums as u16 instead of short.
- Use unsigned int for local indexes.
- Use min_t instead of the ternary operator.
- Refactor the loop in t7xx_dpmaif_rx_data_collect() to avoid a dead
  condition check.
- Use a bitmap (bat_bitmap) instead of an array to keep track of
  the DRB status. Used in t7xx_dpmaif_avail_pkt_bat_cnt().
- Refactor t7xx_dpmaif_tx_send_skb() to protect tx_submit_skb_cnt
  with spinlock and remove the misleading tx_drb_available variable.
- Consolidate bit operations before endianness conversion.
- Use C bit fields in dpmaif_drb_skb struct which is not HW related.
- Add back the que_started check in t7xx_select_tx_queue().
- Create a helper function to get the DRB count.
- Simplify the use of 'usage' during t7xx_ccmni_close().
- Enforce CCMNI MTU selection with BUILD_BUG_ON() instead of a comment.
- Remove t7xx_ccmni_ctrl->capability parameter which remains constant.

v4:
- Implement list_prev_entry_circular() and list_next_entry_circular() macros.
- Remove inline from all c files.
- Define ioread32_poll_timeout_atomic() helper macro.
- Fix return code for WWAN port tx op.
- Allow AT commands fragmentation same as MBIM commands.
- Introduce t7xx_common.h file in the first patch.
- Rename functions and variables as suggested in v3.
- Reduce code duplication by creating fsm_wait_for_event() helper function.
- Remove unneeded dev_err in t7xx_fsm_clr_event().
- Remove unused variable last_state from struct t7xx_fsm_ctl.
- Remove unused variable txq_select_times from struct dpmaif_ctrl.
- Replace ETXTBSY with EBUSY.
- Refactor t7xx_dpmaif_rx_buf_alloc() to remove an unneeded allocation.
- Fix potential leak at t7xx_dpmaif_rx_frag_alloc().
- Simplify return value handling at t7xx_dpmaif_rx_start().
- Add a helper to handle the common part of CCCI header initialization.
- Make sure interrupts are enabled during PM resume.
- Add a parameter to t7xx_fsm_append_cmd() to tell if it is in interrupt context.

v3:
- Avoid unneeded ping-pong changes between patches.
- Use t7xx_ prefix in functions.
- Use t7xx_ prefix in generic structs where mtk_ or ccci prefix was used.
- Update Authors/Contributors header.
- Remove skb pools used for control path.
- Remove skb pools used for RX data path.
- Do not use dedicated TX queue for ACK-only packets.
- Remove __packed attribute from GPD structs.
- Remove the infrastructure for test and debug ports.
- Use the skb control buffer to store metadata.
- Get the IP packet type from RX PIT.
- Merge variable declaration and simple assignments.
- Use preferred coding patterns.
- Remove global variables.
- Declare HW facing structure members as little endian.
- Rename goto tags to describe what is going to be done.
- Do not use variable length arrays.
- Remove unneeded blank lines source code and kdoc headers.
- Use C99 initialization format for port-proxy ports.
- Clean up comments.
- Review included headers.
- Better use of 100 column limit.
- Remove unneeded mb() in CLDMA.
- Remove unneeded spin locks and atomics.
- Handle read_poll_timeout error.
- Use dev_err_ratelimited() where required.
- Fix resource leak when requesting IRQs.
- Use generic DEFAULT_TX_QUEUE_LEN instead custom macro.
- Use ETH_DATA_LEN instead of defining WWAN_DEFAULT_MTU.
- Use sizeof() instead of defines when the size of structures is required.
- Remove unneeded code from netdev:
    No need to configure HW address length
    No need to implement .ndo_change_mtu
    Remove random address generation
- Code simplifications by using kernel provided functions and macros such as:
    module_pci_driver
    PTR_ERR_OR_ZERO
    for_each_set_bit
    pci_device_is_present
    skb_queue_purge
    list_prev_entry
    __ffs64

v2:
- Replace pdev->driver->name with dev_driver_string(&pdev->dev).
- Replace random_ether_addr() with eth_random_addr().
- Update kernel-doc comment for enum data_policy.
- Indicate the driver is 'Supported' instead of 'Maintained'.
- Fix the Signed-of-by and Co-developed-by tags in the patches.
- Added authors and contributors in the top comment of the src files.
====================

Adds maintainers and documentation for MediaTek t7xx 5G WWAN modem
device driver.
Signed-off-by: Ricardo Martinez <ricardo.martinez@linux.intel.com>
Reviewed-by: Loic Poulain <loic.poulain@linaro.org>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Reviewed-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Introduce the mechanism to lock/unlock the device 'deep sleep' mode.
When the PCIe link state is L1.2 or L2, the host side still can keep
the device is in D0 state from the host side point of view. At the same
time, if the device's 'deep sleep' mode is unlocked, the device will
go to 'deep sleep' while it is still in D0 state on the host side.
Signed-off-by: Haijun Liu <haijun.liu@mediatek.com>
Signed-off-by: Chandrashekar Devegowda <chandrashekar.devegowda@intel.com>
Co-developed-by: Ricardo Martinez <ricardo.martinez@linux.intel.com>
Signed-off-by: Ricardo Martinez <ricardo.martinez@linux.intel.com>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Enables runtime power management callbacks including runtime_suspend
and runtime_resume. Autosuspend is used to prevent overhead by frequent
wake-ups.
Signed-off-by: Haijun Liu <haijun.liu@mediatek.com>
Signed-off-by: Chandrashekar Devegowda <chandrashekar.devegowda@intel.com>
Co-developed-by: Eliot Lee <eliot.lee@intel.com>
Signed-off-by: Eliot Lee <eliot.lee@intel.com>
Signed-off-by: Ricardo Martinez <ricardo.martinez@linux.intel.com>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Implements suspend, resumes, freeze, thaw, poweroff, and restore
`dev_pm_ops` callbacks.

From the host point of view, the t7xx driver is one entity. But, the
device has several modules that need to be addressed in different ways
during power management (PM) flows.
The driver uses the term 'PM entities' to refer to the 2 DPMA and
2 CLDMA HW blocks that need to be managed during PM flows.
When a dev_pm_ops function is called, the PM entities list is iterated
and the matching function is called for each entry in the list.
Signed-off-by: Haijun Liu <haijun.liu@mediatek.com>
Signed-off-by: Chandrashekar Devegowda <chandrashekar.devegowda@intel.com>
Co-developed-by: Ricardo Martinez <ricardo.martinez@linux.intel.com>
Signed-off-by: Ricardo Martinez <ricardo.martinez@linux.intel.com>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>