Shannon Nelson says:

====================
ionic support for firmware upgrade

The Pensando Distributed Services Card can get firmware upgrades from
the off-host centralized management suite, and can be upgraded without a
host reboot or driver reload.  This patchset sets up the support for fw
upgrade in the Linux driver.

When the upgrade begins, the DSC first brings the link down, then stops
the firmware.  The driver will notice this and quiesce itself by stopping
the queues and releasing DMA resources, then monitoring for firmware to
start back up.  When the upgrade is finished the firmware is restarted
and link is brought up, and the driver rebuilds the queues and restarts
traffic flow.

First we separate the Link state from the netdev state, then reorganize a
few things to prepare for partial tear-down of the queues.  Next we fix
up the state machine so that we take the Tx and Rx queues down and back
up when we get LINK_DOWN and LINK_UP events.  Lastly, we add handling of
the FW reset itself by tearing down the lif internals and rebuilding them
with the new FW setup.

v2: This changes the design from (ab)using the full .ndo_stop and
    .ndo_open routines to getting a better separation between the
    alloc and the init functions so that we can keep our resource
    allocations as long as possible.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

When the FW RESET event comes to the driver from the firmware,
or the fw_status goes to 0 (stopped) or to 0xff (no PCI
connection), then shut down the driver activity.  This event
signals a FW upgrade where we need to quiesce all operations and
wait for the FW to restart.  The FW will continue the update
process once it sees all the LIFs are reset.  When the update
process is done it will set the fw_status back to RUNNING.
Meanwhile, the heartbeat check continues and when the fw_status
is seen as set to running we can restart the driver operations.
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>

When the link goes down, we need to disable the queues on the
NIC in addition to stopping the netdev stack.  This lets the
FW know that the driver has stopped queue activity, and then
the FW can do internal reconfiguration work, whether actually
Link related, or for other internal FW needs.  To do this,
we pull out the queue enable and disable from ionic_open()
and ionic_stop() so they can be used by other routines.

To help keep things sane, we swap the queue enables so that
the rx queue and its napi are enabled before the tx queue
which rides on the rx queues napi.

We also drop the ionic_lif_quiesce() as it doesn't do anything
more than what the queue disable has already taken care of.
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>

Make sure the queue structures exist before trying
to delete them.  This addresses a couple of error
recovery issues.
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>

Clean out tx requests that didn't get finished before
shutting down the queue.
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>

Move the irq request and free out of the qcq_init and deinit
and into the alloc and free routines where they belong for
better resource management.
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>

Move the qcq debugfs add to the queue alloc, and likewise move
the debugfs delete to the queue free.  The LIF debugfs add
also needs to be moved, but the del is already in the LIF free.
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add a link_status_check to the heartbeat watchdog.
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>

Rearrange the link_up/link_down messages so that we announce
link up when we first notice that the link is up when the
driver loads, and decouple the link_up/link_down messages from
the UP and DOWN netdev state.
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>

Cited commit extended the enums 'hwtstamp_tx_types' and
'hwtstamp_rx_filters' with values that were not accounted for in the
switch statements, resulting in the build warnings below.

Fix by adding a default case.

drivers/net/ethernet/mellanox/mlxsw/spectrum_ptp.c: In function ‘mlxsw_sp_ptp_get_message_types’:
drivers/net/ethernet/mellanox/mlxsw/spectrum_ptp.c:915:2: warning: enumeration value ‘__HWTSTAMP_TX_CNT’ not handled in switch [-Wswitch]
  915 |  switch (tx_type) {
      |  ^~~~~~
drivers/net/ethernet/mellanox/mlxsw/spectrum_ptp.c:927:2: warning: enumeration value ‘__HWTSTAMP_FILTER_CNT’ not handled in switch [-Wswitch]
  927 |  switch (rx_filter) {
      |  ^~~~~~

Fixes: f76510b4 ("ethtool: add timestamping related string sets")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reported-by: David S. Miller <davem@davemloft.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

Eran Ben Elisha says:

====================
Devlink health auto attributes refactor

This patchset refactors the auto-recover health reporter flag to be
explicitly set by the devlink core.
In addition, add another flag to control auto-dump attribute, also
to be explicitly set by the devlink core.

For that, patch 0001 changes the auto-recover default value of
netdevsim dummy reporter.

After reporter registration, both flags can be altered be administrator
only.

Changes since v1:
- Change default behaviour of netdevsim dummy reporter
- Move initialization of DEVLINK_ATTR_HEALTH_REPORTER_AUTO_DUMP
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

On low memory system, run time dumps can consume too much memory. Add
administrator ability to disable auto dumps per reporter as part of the
error flow handle routine.

This attribute is not relevant while executing
DEVLINK_CMD_HEALTH_REPORTER_DUMP_GET.

By default, auto dump is activated for any reporter that has a dump method,
as part of the reporter registration to devlink.
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When health reporter is registered to devlink, devlink will implicitly set
auto recover if and only if the reporter has a recover method. No reason
to explicitly get the auto recover flag from the driver.

Remove this flag from all drivers that called
devlink_health_reporter_create.

All existing health reporters set auto recovery to true if they have a
recover method.

Yet, administrator can unset auto recover via netlink command as prior to
this patch.
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Health reporters should be registered with auto recover set to true.
Align dummy reporter behaviour with that, as in later patch the option to
set auto recover behaviour will be removed.

In addition, align netdevsim selftest to the new default value.
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The PTP Hardware Clock (PHC) subsystem offers an API for configuring
programmable pins.  User space sets or gets the settings using ioctls,
and drivers verify dialed settings via a callback.  Drivers may also
query pin settings by calling the ptp_find_pin() method.

Although the core subsystem protects concurrent access to the pin
settings, the implementation places illogical restrictions on how
drivers may call ptp_find_pin().  When enabling an auxiliary function
via the .enable(on=1) callback, drivers may invoke the pin finding
method, but when disabling with .enable(on=0) drivers are not
permitted to do so.  With the exception of the mv88e6xxx, all of the
PHC drivers do respect this restriction, but still the locking pattern
is both confusing and unnecessary.

This patch changes the locking implementation to allow PHC drivers to
freely call ptp_find_pin() from their .enable() and .verify()
callbacks.

V2 ChangeLog:
- fixed spelling in the kernel doc
- add Vladimir's tested by tag
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Reported-by: Yangbo Lu <yangbo.lu@nxp.com>
Tested-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The rest of the devlink code sets the extack message using
NL_SET_ERR_MSG_MOD. Change the existing appearances of NL_SET_ERR_MSG
to NL_SET_ERR_MSG_MOD.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Jiri Pirko says:

====================
net: sched: expose HW stats types per action used by drivers

The first patch is just adding a helper used by the second patch too.
The second patch is exposing HW stats types that are used by drivers.

Example:

$ tc filter add dev enp3s0np1 ingress proto ip handle 1 pref 1 flower dst_ip 192.168.1.1 action drop
$ tc -s filter show dev enp3s0np1 ingress
filter protocol ip pref 1 flower chain 0
filter protocol ip pref 1 flower chain 0 handle 0x1
  eth_type ipv4
  dst_ip 192.168.1.1
  in_hw in_hw_count 2
        action order 1: gact action drop
         random type none pass val 0
         index 1 ref 1 bind 1 installed 10 sec used 10 sec
        Action statistics:
        Sent 0 bytes 0 pkt (dropped 0, overlimits 0 requeues 0)
        backlog 0b 0p requeues 0
        used_hw_stats immediate     <<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

It may be up to the driver (in case ANY HW stats is passed) to select
which type of HW stats he is going to use. Add an infrastructure to
expose this information to user.

$ tc filter add dev enp3s0np1 ingress proto ip handle 1 pref 1 flower dst_ip 192.168.1.1 action drop
$ tc -s filter show dev enp3s0np1 ingress
filter protocol ip pref 1 flower chain 0
filter protocol ip pref 1 flower chain 0 handle 0x1
  eth_type ipv4
  dst_ip 192.168.1.1
  in_hw in_hw_count 2
        action order 1: gact action drop
         random type none pass val 0
         index 1 ref 1 bind 1 installed 10 sec used 10 sec
        Action statistics:
        Sent 0 bytes 0 pkt (dropped 0, overlimits 0 requeues 0)
        backlog 0b 0p requeues 0
        used_hw_stats immediate     <<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Introduce a helper to pass value and selector to. The helper packs them
into struct and puts them into netlink message.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Steffen Klassert says:

====================
pull request (net-next): ipsec-next 2020-03-28

1) Use kmem_cache_zalloc() instead of kmem_cache_alloc()
   in xfrm_state_alloc(). From Huang Zijiang.

2) esp_output_fill_trailer() is the same in IPv4 and IPv6,
   so share this function to avoide code duplcation.
   From Raed Salem.

3) Add offload support for esp beet mode.
   From Xin Long.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

There is no point in preparing the module name in a buffer. The format
string can be passed diectly to 'request_module()'.

This axes a few lines of code and cleans a few things:
   - max len for a driver name is MODULE_NAME_LEN wich is ~ 60 chars,
     not 128. It would be down-sized in 'request_module()'
   - we should pass the total size of the buffer to 'snprintf()', not the
     size minus 1
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

Fix sparse warnings:

drivers/net/ethernet/amazon/ena/ena_netdev.c:460:6: warning: symbol 'ena_xdp_exchange_program_rx_in_range' was not declared. Should it be static?
drivers/net/ethernet/amazon/ena/ena_netdev.c:481:6: warning: symbol 'ena_xdp_exchange_program' was not declared. Should it be static?
drivers/net/ethernet/amazon/ena/ena_netdev.c:1555:5: warning: symbol 'ena_xdp_handle_buff' was not declared. Should it be static?
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Fix sparse warning:

drivers/net/ethernet/freescale/dpaa/dpaa_eth.c:2065:5:
 warning: symbol 'dpaa_a050385_wa' was not declared. Should it be static?
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

There is a possibility that cdev is removed before CPL_ABORT_REQ_RSS
is fully processed, so it's better to save it in skb.

Added checks in handling the flow correctly, which suggests connection reset
request is sent to HW, wait for HW to respond.
Signed-off-by: Rohit Maheshwari <rohitm@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

IPv6 header's payload length field shouldn't include IPv6 header length.
Signed-off-by: Rohit Maheshwari <rohitm@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add support for VLAN ID-based filtering by the MAC controller for MAC
drivers that support it. Only the 12-bit VID field is used.
Signed-off-by: Chuah Kim Tatt <kim.tatt.chuah@intel.com>
Signed-off-by: Ong Boon Leong <boon.leong.ong@intel.com>
Signed-off-by: Wong Vee Khee <vee.khee.wong@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Ayush Sawal says:

====================
crypto: chelsio: Fixes issues during chcr driver registration

Patch 1: Avoid the accessing of wrong u_ctx pointer.
Patch 2: Fixes a deadlock between rtnl_lock and uld_mutex.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

The locks are taken in this order during driver registration
(uld_mutex), at: cxgb4_register_uld.part.14+0x49/0xd60 [cxgb4]
(rtnl_mutex), at: rtnetlink_rcv_msg+0x2db/0x400
(uld_mutex), at: cxgb_up+0x3a/0x7b0 [cxgb4]
(rtnl_mutex), at: chcr_add_xfrmops+0x83/0xa0 [chcr](stucked here)

To avoid this now the netdev features are updated after the
cxgb4_register_uld function is completed.

Fixes: 6dad4e8a ("chcr: Add support for Inline IPSec").
Signed-off-by: Ayush Sawal <ayush.sawal@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This issue occurs only when multiadapters are present. Hang
happens because assign_chcr_device returns u_ctx pointer of
adapter which is not yet initialized as for this adapter cxgb_up
is not been called yet.

The last_dev pointer is used to determine u_ctx pointer and it
is initialized two times in chcr_uld_add in chcr_dev_add respectively.

The fix here is don't initialize the last_dev pointer during
chcr_uld_add. Only assign to value to it when the adapter's
initialization is completed i.e in chcr_dev_add.

Fixes: fef4912b ("crypto: chelsio - Handle PCI shutdown event").
Signed-off-by: Ayush Sawal <ayush.sawal@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

'pm_nl_ctl' was adding a trailing whitespace after having printed the
IP. But at the end, the IP element is currently always the last one.

The bash script launching 'pm_nl_ctl' had trailing whitespaces in the
expected result on purpose. But these whitespaces have been removed when
the patch has been applied upstream. To avoid trailing whitespaces in
the bash code, 'pm_nl_ctl' and expected results have now been adapted.

The MPTCP PM selftest can now pass again.

Fixes: eedbc685 (selftests: add PM netlink functional tests)
Signed-off-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

There is a spelling mistake in a dev_err error message. Fix it.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Saeed Mahameed says:

====================
mlx5-updates-2020-03-29

1) mlx5 core level updates for mkey APIs + migrate some code to mlx5_ib

2) Use a separate work queue for fib event handling

3) Move new eswitch chains files to a new directory, to prepare for
upcoming E-Switch and offloads features.

4) Support indr block setup (TC_SETUP_FT) in Flow Table mode.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Add mlx5e_rep_indr_setup_ft_cb to support indr block setup
in FT mode.
Both tc rules and flow table rules are of the same format,
It can re-use tc parsing for that, and move the flow table rules
to their steering domain(the specific chain_index), the indr
block offload in FT also follow this scenario.
Signed-off-by: wenxu <wenxu@ucloud.cn>
Reviewed-by: Vlad Buslov <vladbu@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

Refactor indr setup block for support ft indr setup in the
next patch. The function mlx5e_rep_indr_offload exposes
'flags' in order set additional flag for FT in next patch.
Rename mlx5e_rep_indr_setup_tc_block to mlx5e_rep_indr_setup_block
and add flow_setup_cb_t callback parameters in order set the
specific callback for FT in next patch.
Signed-off-by: wenxu <wenxu@ucloud.cn>
Reviewed-by: Vlad Buslov <vladbu@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

eswitch_offloads_chains.{c,h} were just introduced this kernel release
cycle, eswitch is in high development demand right now and many
features are planned to be added to it. eswitch deserves its own
directory and here we move these new files to there, in preparation for
upcoming eswitch features and new files.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Reviewed-by: Mark Bloch <markb@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>

In VF lag mode when remove the bonding module without bring down the
bond device first, we could potentially have circular dependency when we
unload IB devices and also handle fib events:
1. The bond work starts first;
2. The "modprobe -rv bonding" process tries to release the bond device,
   with the "pernet_ops_rwsem" lock hold;
3. The bond work blocks in unregister_netdevice_notifier() and waits for
the lock because fib event came right before;
4. The kernel fib module tries to free all the fib entries by broadcasting
   the "FIB_EVENT_NH_DEL" event;
5. Upon the fib event this lag_mp module holds the fib lock and queue a
   fib work.
So:
   bond work -> modprobe task -> kernel fib module -> lag_mp -> bond work

Today we either reload IB devices in roce lag in nic mode or either handle
fib events in switchdev mode, but a new feature could change that we'll
need to reload IB devices also in switchdev mode so this is a future proof
fix as one may not notice this later.
Signed-off-by: Mark Zhang <markz@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

* 'mlx5-next' of git://git.kernel.org/pub/scm/linux/kernel/git/mellanox/linux:
  mlx5: Remove uninitialized use of key in mlx5_core_create_mkey
  {IB,net}/mlx5: Move asynchronous mkey creation to mlx5_ib
  {IB,net}/mlx5: Assign mkey variant in mlx5_ib only
  {IB,net}/mlx5: Setup mkey variant before mr create command invocation
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

Michal Kubecek says:

====================
ethtool netlink interface, part 4

Implementation of more netlink request types:

  - coalescing (ethtool -c/-C, patches 2-4)
  - pause parameters (ethtool -a/-A, patches 5-7)
  - EEE settings (--show-eee / --set-eee, patches 8-10)
  - timestamping info (-T, patches 11-12)

Patch 1 is a fix for netdev reference leak similar to commit 2f599ec4
("ethtool: fix reference leak in some *_SET handlers") but fixing a code

Changes in v3
  - change "one-step-*" Tx type names to "onestep-*", (patch 11, suggested
    by Richard Cochran
  - use "TSINFO" rather than "TIMESTAMP" for timestamping information
    constants and adjust symbol names (patch 12, suggested by Richard
    Cochran)

Changes in v2:
  - fix compiler warning in net_hwtstamp_validate() (patch 11)
  - fix follow-up lines alignment (whitespace only, patches 3 and 8)
which is only in net-next tree at the moment.
====================
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Implement TSINFO_GET request to get timestamping information for a network
device. This is traditionally available via ETHTOOL_GET_TS_INFO ioctl
request.

Move part of ethtool_get_ts_info() into common.c so that ioctl and netlink
code use the same logic to get timestamping information from the device.

v3: use "TSINFO" rather than "TIMESTAMP", suggested by Richard Cochran
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add three string sets related to timestamping information:

  ETH_SS_SOF_TIMESTAMPING: SOF_TIMESTAMPING_* flags
  ETH_SS_TS_TX_TYPES:      timestamping Tx types
  ETH_SS_TS_RX_FILTERS:    timestamping Rx filters

These will be used for TIMESTAMP_GET request.

v2: avoid compiler warning ("enumeration value not handled in switch")
    in net_hwtstamp_validate()

v3: omit dash in Tx type names ("one-step-*" -> "onestep-*"), suggested by
    Richard Cochran
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>