- 30 Mar, 2017 40 commits
-
-
Tomas Winkler authored
commit a733ded5 upstream. This patch fixes 'mei: synchronize irq before initiating a reset' The patch had introduced a deadlock between irq thread and mei_reset() as they are both holding the same device lock. ---> device_lock: mei_reset() <---- interrupt thread device_lock ---> synchornize_irq() wait on interrupt thread == (dead lock) The fix is to call synchronize_irq prior to call locked mei_reset function. Fixes: f302bb0de6ac (mei: synchronize irq before initiating a reset) Signed-off-by:
Tomas Winkler <tomas.winkler@intel.com> Signed-off-by:
Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Dmitry Torokhov authored
commit 3ff861f5 upstream. Even if bus is not hot-pluggable, devices can be unbound from the driver via sysfs, so we should not be using __exit annotations on remove() methods. The only exception is drivers registered with platform_driver_probe() which specifically disables sysfs bind/unbind attributes. Signed-off-by:
Dmitry Torokhov <dmitry.torokhov@gmail.com> Reviewed-by:
Linus Walleij <linus.walleij@linaro.org> Signed-off-by:
Jonathan Cameron <jic23@kernel.org> Signed-off-by:
-
Song Hongyan authored
iio: hid-sensor-trigger: Change get poll value function order to avoid sensor properties losing after resume from S3 commit 3bec2474 upstream. In function _hid_sensor_power_state(), when hid_sensor_read_poll_value() is called, sensor's all properties will be updated by the value from sensor hardware/firmware. In some implementation, sensor hardware/firmware will do a power cycle during S3. In this case, after resume, once hid_sensor_read_poll_value() is called, sensor's all properties which are kept by driver during S3 will be changed to default value. But instead, if a set feature function is called first, sensor hardware/firmware will be recovered to the last status. So change the sensor_hub_set_feature() calling order to behind of set feature function to avoid sensor properties lose. Signed-off-by:
Song Hongyan <hongyan.song@intel.com> Acked-by:
Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com> Signed-off-by:
-
Lars-Peter Clausen authored
commit c42f8218 upstream. Use the IS_ENABLED() helper macro to ensure that the configfs group is initialized either when configfs is built-in or when configfs is built as a module. Otherwise software device creation will result in undefined behaviour when configfs is built as a module since the configfs group for the device not properly initialized. Similar to commit b2f0c096 ("iio: sw-trigger: Fix config group initialization"). Fixes: 0f3a8c3f ("iio: Add support for creating IIO devices via configfs") Reported-by:
Miguel Robles <miguel.robles@farole.net> Signed-off-by:
Lars-Peter Clausen <lars@metafoo.de> Acked-by:
Daniel Baluta <daniel.baluta@gmail.com> Signed-off-by:
-
Michael Engl authored
commit e83bb3e6 upstream. The tiadc_irq_h(int irq, void *private) function is handling FIFO overruns by clearing flags, disabling and enabling the ADC to recover. If the ADC is running in continuous mode a FIFO overrun happens regularly. If the disabling of the ADC happens concurrently with a new conversion. It might happen that the enabling of the ADC is ignored by the hardware. This stops the ADC permanently. No more interrupts are triggered. According to the AM335x Reference Manual (SPRUH73H October 2011 - Revised April 2013 - Chapter 12.4 and 12.5) it is necessary to check the ADC FSM bits in REG_ADCFSM before enabling the ADC again. Because the disabling of the ADC is done right after the current conversion has been finished. To trigger this bug it is necessary to run the ADC in continuous mode. The ADC values of all channels need to be read in an endless loop. The bug appears within the first 6 hours (~5.4 million handled FIFO overruns). The user space application will hang on reading new values from the character device. Fixes: ca9a5638 ("iio: ti_am335x_adc: Add continuous sampling support") Signed-off-by:
Michael Engl <michael.engl@wjw-solutions.com> Signed-off-by:
-
Guenter Roeck authored
commit 773dc118 upstream. HS400-ES devices fail to initialize with the following error messages. mmc1: power class selection to bus width 8 ddr 0 failed mmc1: error -110 whilst initialising MMC card This was seen on Samsung Chromebook Plus. Code analysis points to commit 3d4ef329 ("mmc: core: fix multi-bit bus width without high-speed mode"), which attempts to set the bus width for all but HS200 devices unconditionally. However, for HS400-ES, the bus width is already selected. Cc: Anssi Hannula <anssi.hannula@bitwise.fi> Cc: Douglas Anderson <dianders@chromium.org> Cc: Brian Norris <briannorris@chromium.org> Fixes: 3d4ef329 ("mmc: core: fix multi-bit bus width ...") Signed-off-by:
Guenter Roeck <linux@roeck-us.net> Reviewed-by:
Douglas Anderson <dianders@chromium.org> Reviewed-by:
Shawn Lin <shawn.lin@rock-chip.com> Tested-by:
Heiko Stuebner <heiko@sntech.de> Signed-off-by:
Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by:
-
Johannes Berg authored
commit ea90e0dc upstream. Sowmini pointed out Dmitry's RTNL deadlock report to me, and it turns out to be perfectly accurate - there are various error paths that miss unlock of the RTNL. To fix those, change the locking a bit to not be conditional in all those nl80211_prepare_*_dump() functions, but make those require the RTNL to start with, and fix the buggy error paths. This also let me use sparse (by appropriately overriding the rtnl_lock/rtnl_unlock functions) to validate the changes. Reported-by:
Sowmini Varadhan <sowmini.varadhan@oracle.com> Reported-by:
Dmitry Vyukov <dvyukov@google.com> Signed-off-by:
Johannes Berg <johannes.berg@intel.com> Signed-off-by:
-
Johan Hovold authored
commit 181302dc upstream. Make sure to check the number of endpoints to avoid dereferencing a NULL-pointer should a malicious device lack endpoints. Fixes: 53f3a9e2 ("mmc: USB SD Host Controller (USHC) driver") Cc: David Vrabel <david.vrabel@csr.com> Signed-off-by:
Johan Hovold <johan@kernel.org> Signed-off-by:
-
Johan Hovold authored
commit daf229b1 upstream. Make sure to check the number of endpoints to avoid dereferencing a NULL-pointer should a malicious device lack endpoints. Note that the dereference happens in the start callback which is called during probe. Fixes: de520b8b ("uwb: add HWA radio controller driver") Cc: Inaky Perez-Gonzalez <inaky.perez-gonzalez@intel.com> Cc: David Vrabel <david.vrabel@csr.com> Signed-off-by:
-
Johan Hovold authored
commit 4ce36271 upstream. Make sure to check the number of endpoints to avoid dereferencing a NULL-pointer should a malicious device lack endpoints. Note that the dereference happens in the cmd and wait_init_done callbacks which are called during probe. Fixes: 1ba47da5 ("uwb: add the i1480 DFU driver") Cc: Inaky Perez-Gonzalez <inaky.perez-gonzalez@intel.com> Cc: David Vrabel <david.vrabel@csr.com> Signed-off-by:
-
Johan Hovold authored
commit 2e47c535 upstream. Make sure to initialise the return value to avoid having allocation failures going unnoticed when allocating interrupt-endpoint resources. This prevents use-after-free or worse when the device is later unbound. Fixes: dbf3e7f6 ("Implement an ioctl to support the USMTMC-USB488 READ_STATUS_BYTE operation.") Cc: Dave Penkler <dpenkler@gmail.com> Signed-off-by:
-
Johan Hovold authored
commit 687e0687 upstream. USBTMC devices are required to have a bulk-in and a bulk-out endpoint, but the driver failed to verify this, something which could lead to the endpoint addresses being taken from uninitialised memory. Make sure to zero all private data as part of allocation, and add the missing endpoint sanity check. Note that this also addresses a more recently introduced issue, where the interrupt-in-presence flag would also be uninitialised whenever the optional interrupt-in endpoint is not present. This in turn could lead to an interrupt urb being allocated, initialised and submitted based on uninitialised values. Fixes: dbf3e7f6 ("Implement an ioctl to support the USMTMC-USB488 READ_STATUS_BYTE operation.") Fixes: 5b775f67 ("USB: add USB test and measurement class driver") Signed-off-by:
-
Guenter Roeck authored
commit 7b2db29f upstream. If usb_get_bos_descriptor() returns an error, usb->bos will be NULL. Nevertheless, it is dereferenced unconditionally in hub_set_initial_usb2_lpm_policy() if usb2_hw_lpm_capable is set. This results in a crash. usb 5-1: unable to get BOS descriptor ... Unable to handle kernel NULL pointer dereference at virtual address 00000008 pgd = ffffffc00165f000 [00000008] *pgd=000000000174f003, *pud=000000000174f003, *pmd=0000000001750003, *pte=00e8000001751713 Internal error: Oops: 96000005 [#1] PREEMPT SMP Modules linked in: uinput uvcvideo videobuf2_vmalloc cmac [ ... ] CPU: 5 PID: 3353 Comm: kworker/5:3 Tainted: G B 4.4.52 #480 Hardware name: Google Kevin (DT) Workqueue: events driver_set_config_work task: ffffffc0c3690000 ti: ffffffc0ae9a8000 task.ti: ffffffc0ae9a8000 PC is at hub_port_init+0xc3c/0xd10 LR is at hub_port_init+0xc3c/0xd10 ... Call trace: [<ffffffc0007fbbfc>] hub_port_init+0xc3c/0xd10 [<ffffffc0007fbe2c>] usb_reset_and_verify_device+0x15c/0x82c [<ffffffc0007fc5e0>] usb_reset_device+0xe4/0x298 [<ffffffbffc0e3fcc>] rtl8152_probe+0x84/0x9b0 [r8152] [<ffffffc00080ca8c>] usb_probe_interface+0x244/0x2f8 [<ffffffc000774a24>] driver_probe_device+0x180/0x3b4 [<ffffffc000774e48>] __device_attach_driver+0xb4/0xe0 [<ffffffc000772168>] bus_for_each_drv+0xb4/0xe4 [<ffffffc0007747ec>] __device_attach+0xd0/0x158 [<ffffffc000775080>] device_initial_probe+0x24/0x30 [<ffffffc0007739d4>] bus_probe_device+0x50/0xe4 [<ffffffc000770bd0>] device_add+0x414/0x738 [<ffffffc000809fe8>] usb_set_configuration+0x89c/0x914 [<ffffffc00080a120>] driver_set_config_work+0xc0/0xf0 [<ffffffc000249bb8>] process_one_work+0x390/0x6b8 [<ffffffc00024abcc>] worker_thread+0x480/0x610 [<ffffffc000251a80>] kthread+0x164/0x178 [<ffffffc0002045d0>] ret_from_fork+0x10/0x40 Since we don't know anything about LPM capabilities without BOS descriptor, don't attempt to enable LPM if it is not available. Fixes: 890dae88 ("xhci: Enable LPM support only for hardwired ...") Cc: Mathias Nyman <mathias.nyman@linux.intel.com> Signed-off-by:
Mathias Nyman <mathias.nyman@linux.intel.com> Signed-off-by:
-
Bin Liu authored
commit 0090114d upstream. The CPPI 4.1 driver polls register to workaround the premature TX interrupt issue, but it causes audio playback underrun when triggered in Isoch transfers. Isoch doesn't do back-to-back transfers, the TX should be done by the time the next transfer is scheduled. So skip this polling workaround for Isoch transfer. Fixes: a655f481 ("usb: musb: musb_cppi41: handle pre-mature TX complete interrupt") Reported-by:
Alexandre Bailon <abailon@baylibre.com> Acked-by:
Sebastian Andrzej Siewior <bigeasy@linutronix.de> Tested-by:
Bin Liu <b-liu@ti.com> Signed-off-by:
-
Johan Hovold authored
commit 03ace948 upstream. Make sure to check the number of endpoints to avoid dereferencing a NULL-pointer or accessing memory beyond the endpoint array should a malicious device lack the expected endpoints. This specifically fixes the NULL-pointer dereference when probing HWA HC devices. Fixes: df365423 ("wusb: add the Wire Adapter (WA) core") Cc: Inaky Perez-Gonzalez <inaky.perez-gonzalez@intel.com> Cc: David Vrabel <david.vrabel@csr.com> Signed-off-by:
-
Johan Hovold authored
commit b0addd3f upstream. Make sure to check the number of endpoints to avoid dereferencing a NULL-pointer should a malicious device lack endpoints. Fixes: 1da177e4 ("Linux-2.6.12-rc2") Signed-off-by:
-
Johan Hovold authored
commit 1dc56c52 upstream. Make sure to check the number of endpoints to avoid dereferencing a NULL-pointer should the probed device lack endpoints. Note that this driver does not bind to any devices by default. Fixes: ce21bfe6 ("USB: Add LVS Test device driver") Cc: Pratyush Anand <pratyush.anand@gmail.com> Signed-off-by:
-
Johan Hovold authored
commit f259ca3e upstream. Make sure to check the number of endpoints to avoid dereferencing a NULL-pointer or accessing memory beyond the endpoint array should a malicious device lack the expected endpoints. Note that the endpoint access that causes the NULL-deref is currently only used for debugging purposes during probe so the oops only happens when dynamic debugging is enabled. This means the driver could be rewritten to continue to accept device with only two endpoints, should such devices exist. Fixes: 1da177e4 ("Linux-2.6.12-rc2") Signed-off-by:
-
Samuel Thibault authored
commit 3243367b upstream. Some USB 2.0 devices erroneously report millisecond values in bInterval. The generic config code manages to catch most of them, but in some cases it's not completely enough. The case at stake here is a USB 2.0 braille device, which wants to announce 10ms and thus sets bInterval to 10, but with the USB 2.0 computation that yields to 64ms. It happens that one can type fast enough to reach this interval and get the device buffers overflown, leading to problematic latencies. The generic config code does not catch this case because the 64ms is considered a sane enough value. This change thus adds a USB_QUIRK_LINEAR_FRAME_INTR_BINTERVAL quirk to mark devices which actually report milliseconds in bInterval, and marks Vario Ultra devices as needing it. Signed-off-by:
Samuel Thibault <samuel.thibault@ens-lyon.org> Acked-by:
Alan Stern <stern@rowland.harvard.edu> Signed-off-by:
-
Stefan Brüns authored
commit 67b0503d upstream. The buffer allocation for the firmware data was changed in commit 43fab979 ("[media] dvb-usb: don't use stack for firmware load") but the same applies for the reset value. Fixes: 43fab979 ("[media] dvb-usb: don't use stack for firmware load") Signed-off-by:
Stefan Brüns <stefan.bruens@rwth-aachen.de> Signed-off-by:
Mauro Carvalho Chehab <mchehab@s-opensource.com> Signed-off-by:
-
Roger Quadros authored
commit 09424c50 upstream. The streaming_maxburst module parameter is 0 offset (0..15) so we must add 1 while using it for wBytesPerInterval calculation for the SuperSpeed companion descriptor. Without this host uvcvideo driver will always see the wrong wBytesPerInterval for SuperSpeed uvc gadget and may not find a suitable video interface endpoint. e.g. for streaming_maxburst = 0 case it will always fail as wBytePerInterval was evaluating to 0. Reviewed-by:
Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by:
Roger Quadros <rogerq@ti.com> Signed-off-by:
Felipe Balbi <felipe.balbi@linux.intel.com> Signed-off-by:
-
Oliver Neukum authored
commit cdd7928d upstream. The gadget code exports the bitfield for serial status changes over the wire in its internal endianness. The fix is to convert to little endian before sending it over the wire. Signed-off-by:
Oliver Neukum <oneukum@suse.com> Tested-by:
家瑋 <momo1208@gmail.com> Signed-off-by:
-
Bjørn Mork authored
commit 436ecf55 upstream. This is a Dell branded Sierra Wireless EM7455. Signed-off-by:
Bjørn Mork <bjorn@mork.no> Signed-off-by:
-
Dan Williams authored
commit 6e9f44ea upstream. Add Quectel UC15, UC20, EC21, and EC25. The EC20 is handled by qcserial due to a USB VID/PID conflict with an existing Acer device. Signed-off-by:
Dan Williams <dcbw@redhat.com> Signed-off-by:
-
Hui Wang authored
commit 3f307834 upstream. A new Dell laptop needs to apply ALC269_FIXUP_DELL1_MIC_NO_PRESENCE to fix the headset problem, and the pin definiton of this machine is not in the pin quirk table yet, now adding it to the table. Signed-off-by:
Hui Wang <hui.wang@canonical.com> Signed-off-by:
Takashi Iwai <tiwai@suse.de> Signed-off-by:
-
Takashi Iwai authored
commit f363a066 upstream. In the commit [15c75b09: ALSA: ctxfi: Fallback DMA mask to 32bit], I forgot to put "!" at dam_set_mask() call check in cthw20k1.c (while cthw20k2.c is OK). This patch fixes that obvious bug. (As a side note: although the original commit was completely wrong, it's still working for most of machines, as it sets to 32bit DMA mask in the end. So the bug severity is low.) Fixes: 15c75b09 ("ALSA: ctxfi: Fallback DMA mask to 32bit") Signed-off-by:
-
Takashi Iwai authored
commit c520ff3d upstream. When snd_seq_pool_done() is called, it marks the closing flag to refuse the further cell insertions. But snd_seq_pool_done() itself doesn't clear the cells but just waits until all cells are cleared by the caller side. That is, it's racy, and this leads to the endless stall as syzkaller spotted. This patch addresses the racy by splitting the setup of pool->closing flag out of snd_seq_pool_done(), and calling it properly before snd_seq_pool_done(). BugLink: http://lkml.kernel.org/r/CACT4Y+aqqy8bZA1fFieifNxR2fAfFQQABcBHj801+u5ePV0URw@mail.gmail.comReported-and-tested-by:
-
Johan Hovold authored
commit 92461f5d upstream. Make sure to check the number of endpoints to avoid dereferencing a NULL-pointer or accessing memory that lie beyond the end of the endpoint array should a malicious device lack the expected endpoints. Fixes: bdb5c57f ("Input: add sur40 driver for Samsung SUR40... ") Signed-off-by:
-
Johan Hovold authored
commit cb1b4946 upstream. Make sure to check the number of endpoints to avoid dereferencing a NULL-pointer should a malicious device lack endpoints. Signed-off-by:
-
Johan Hovold authored
commit ac2ee9ba upstream. Make sure to check the number of endpoints to avoid dereferencing a NULL-pointer should a malicious device lack endpoints. Fixes: c04148f9 ("Input: add driver for USB VoIP phones with CM109...") Signed-off-by:
-
Johan Hovold authored
commit 5cc4a1a9 upstream. Make sure to check the number of endpoints to avoid dereferencing a NULL-pointer should a malicious device lack endpoints. Fixes: aca951a2 ("[PATCH] input-driver-yealink-P1K-usb-phone") Signed-off-by:
-
Johan Hovold authored
commit ba340d7b upstream. Make sure to check the number of endpoints to avoid dereferencing a NULL-pointer should a malicious device lack endpoints. Fixes: bba5394a ("Input: add support for Hanwang tablets") Signed-off-by:
-
Johan Hovold authored
commit 1916d319 upstream. Make sure to check the number of endpoints to avoid dereferencing a NULL-pointer should a malicious device lack control-interface endpoints. Fixes: 628329d5 ("Input: add IMS Passenger Control Unit driver") Signed-off-by:
-
Johan Hovold authored
commit 59cf8bed upstream. Make sure to check the number of endpoints to avoid dereferencing a NULL-pointer or accessing memory that lie beyond the end of the endpoint array should a malicious device lack the expected endpoints. Signed-off-by:
-
Kai-Heng Feng authored
commit 45838660 upstream. The aux port does not get detected without noloop quirk, so external PS/2 mouse cannot work as result. The PS/2 mouse can work with this quirk. BugLink: https://bugs.launchpad.net/bugs/1591053Signed-off-by:
Kai-Heng Feng <kai.heng.feng@canonical.com> Reviewed-by:
Marcos Paulo de Souza <marcos.souza.org@gmail.com> Signed-off-by:
-
Matjaz Hegedic authored
commit 92ef6f97 upstream. EeeBook X205TA is yet another ASUS device with a special touchpad firmware that needs to be accounted for during initialization, or else the touchpad will go into an invalid state upon suspend/resume. Adding the appropriate ic_type and product_id check fixes the problem. Signed-off-by:
Matjaz Hegedic <matjaz.hegedic@gmail.com> Acked-by:
KT Liao <kt.liao@emc.com.tw> Signed-off-by:
-
Masaki Ota authored
commit 47e6fb42 upstream. Alps stick devices always have physical buttons, so we should not check ALPS_BUTTONPAD flag to decide whether we should report them. Fixes: 4777ac22 ("Input: ALPS - add touchstick support for SS5 hardware") Signed-off-by:
Masaki Ota <masaki.ota@jp.alps.com> Acked-by:
Pali Rohar <pali.rohar@gmail.com> Tested-by:
Paul Donohue <linux-kernel@PaulSD.com> Tested-by:
Nick Fletcher <nick.m.fletcher@gmail.com> Signed-off-by:
-
Masaki Ota authored
commit e7348396 upstream. Devices identified as E7="73 03 28" use slightly modified version of V8 protocol, with lower count per electrode, different offsets, and different feature bits in OTP data. Fixes: aeaa881f ("Input: ALPS - set DualPoint flag for 74 03 28 devices") Signed-off-by:
-
Roderick Colenbrander authored
commit a687c576 upstream. When a user connects a DS4 twice using USB and BT, we reject the second device connection after the setup work. We then perform a cleanup, but during cleanup we are not removing the touchpad device. This leads to leakage of an input device, which we would never remove. It can likely result into a kernel oops as well when the touchpad evdev node is accessed and the underlaying HID device has been removed from the system. [jkosina@suse.cz: added stable annotation] Fixes: ac797b95 ("HID: sony: Make the DS4 touchpad a separate device") Signed-off-by:
Roderick Colenbrander <roderick.colenbrander@sony.com> Reviewed-by:
Benjamin Tissoires <benjamin.tissoires@redhat.com> Signed-off-by:
Jiri Kosina <jkosina@suse.cz> Signed-off-by:
-
Eric Dumazet authored
commit 39e6c820 upstream. While playing with mlx4 hardware timestamping of RX packets, I found that some packets were received by TCP stack with a ~200 ms delay... Since the timestamp was provided by the NIC, and my probe was added in tcp_v4_rcv() while in BH handler, I was confident it was not a sender issue, or a drop in the network. This would happen with a very low probability, but hurting RPC workloads. A NAPI driver normally arms the IRQ after the napi_complete_done(), after NAPI_STATE_SCHED is cleared, so that the hard irq handler can grab it. Problem is that if another point in the stack grabs NAPI_STATE_SCHED bit while IRQ are not disabled, we might have later an IRQ firing and finding this bit set, right before napi_complete_done() clears it. This can happen with busy polling users, or if gro_flush_timeout is used. But some other uses of napi_schedule() in drivers can cause this as well. thread 1 thread 2 (could be on same cpu, or not) // busy polling or napi_watchdog() napi_schedule(); ... napi->poll() device polling: read 2 packets from ring buffer Additional 3rd packet is available. device hard irq // does nothing because NAPI_STATE_SCHED bit is owned by thread 1 napi_schedule(); napi_complete_done(napi, 2); rearm_irq(); Note that rearm_irq() will not force the device to send an additional IRQ for the packet it already signaled (3rd packet in my example) This patch adds a new NAPI_STATE_MISSED bit, that napi_schedule_prep() can set if it could not grab NAPI_STATE_SCHED Then napi_complete_done() properly reschedules the napi to make sure we do not miss something. Since we manipulate multiple bits at once, use cmpxchg() like in sk_busy_loop() to provide proper transactions. In v2, I changed napi_watchdog() to use a relaxed variant of napi_schedule_prep() : No need to set NAPI_STATE_MISSED from this point. In v3, I added more details in the changelog and clears NAPI_STATE_MISSED in busy_poll_stop() In v4, I added the ideas given by Alexander Duyck in v3 review Signed-off-by:
Eric Dumazet <edumazet@google.com> Cc: Alexander Duyck <alexander.duyck@gmail.com> Signed-off-by:
David S. Miller <davem@davemloft.net> Signed-off-by:
-
