Several drivers that support setting the RS485 configuration via userspace
implement one or more of the following tasks:

- in case of an invalid RTS configuration (both RTS after send and RTS on
  send set or both unset) fall back to enable RTS on send and disable RTS
  after send

- nullify the padding field of the returned serial_rs485 struct

- copy the configuration into the uart port struct

- limit RTS delays to 100 ms

Move these tasks into the serial core to make them generic and to provide
a consistent behaviour among all drivers.
Signed-off-by: Lino Sanfilippo <LinoSanfilippo@gmx.de>
Link: https://lore.kernel.org/r/20220410104642.32195-2-LinoSanfilippo@gmx.deSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Due to chip process differences, chip designers recommend using baud
rates as close to and larger as possible in order to reduce clock
errors.
Signed-off-by: Yu Tu <yu.tu@amlogic.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://lore.kernel.org/r/20220407081355.13602-2-yu.tu@amlogic.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Similar to I2C controller, move geni based QUP UART controller binding
out from parent schema to an individual binding and let parent refer to
child schema later on. UART binding also stand incomplete right now
similar to I2C, complete it along this process.
Signed-off-by: Kuldeep Singh <singh.kuldeep87k@gmail.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20220404182938.29492-4-singh.kuldeep87k@gmail.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Provide information in the kernel log as to what configuration option to
enable for PCI UART devices that have been blacklisted in the generic
PCI 8250 UART driver and which have a dedicated driver available to
handle that has been disabled.  The rationale is there is no easy way
for the user to map a specific PCI vendor:device pair to an individual
dedicated driver while the generic driver has this information readily
available and it will likely be confusing that the generic driver does
not register such a port.

This is unlike usual drivers, such as drivers/net/ethernet/3com/3c59x.c
which handles all the hardware family members regardless of differences
between them, and following an existing example where a serio driver
provides suggestions as to the correct configuration options to use:

psmouse serio1: synaptics: The touchpad can support a better bus than the too old PS/2 protocol. Make sure MOUSE_PS2_SYNAPTICS_SMBUS and RMI4_SMB are enabled to get a better touchpad experience.

A message is then printed like:

serial 0000:04:00.3: ignoring port, enable SERIAL_8250_PERICOM to handle

when an affected device is encountered and the generic driver rejects it.
Signed-off-by: Maciej W. Rozycki <macro@orcam.me.uk>
Link: https://lore.kernel.org/r/alpine.DEB.2.21.2203310054120.44113@angie.orcam.me.ukSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

TTYs in ICANON mode have a special case that allows "pushing" a line
without a regular EOL character (like newline), by using EOF (the EOT
character - ASCII 0x4) as a pseudo-EOL. It is silently discarded, so
the reader of the PTS will receive the line *without* EOF or any other
terminating character.

This special case has an edge case: What happens if the readers buffer
is the same size as the line (without EOF)? Will they be able to tell
if the whole line is received, i.e. if the next read() will return more
of the same line or the next line?

There are two possibilities,  that both have (dis)advantages:

1. The next read() returns 0. FreeBSD (13.0) and OSX (10.11) do this.
   Advantage: The reader can interpret this as "the line is over".
   Disadvantage: read() returning 0 means EOF, the reader could also
   interpret it as "there's no more data" and stop reading or even
   close the PT.

2. The next read() returns the next line, the EOF is silently discarded.
   Solaris (or at least OpenIndiana 2021.10) does this, Linux has done
   do this since commit 40d5e090 ("n_tty: Fix EOF push handling");
   this behavior was recently broken by commit 35930307 ("tty:
   n_tty: do not look ahead for EOL character past the end of the buffer").
   Advantage: read() won't return 0 (EOF), reader less likely to be
   confused (and things like `while(read(..)>0)` don't break)
   Disadvantage: The reader can't really know if the read() continues
   the last line (that filled the whole read buffer) or starts a
   new line.

As both options are defensible (and are used by other Unix-likes), it's
best to stick to the "old" behavior since "n_tty: Fix EOF push handling"
of 2013, i.e. silently discard that EOF.

This patch - that I actually got from Linus for testing and only
modified slightly - restores that behavior by skipping an EOF
character if it's the next character after reading is done.

Based on a patch from Linus Torvalds.

Link: https://bugzilla.kernel.org/show_bug.cgi?id=215611
Fixes: 35930307 ("tty: n_tty: do not look ahead for EOL character past the end of the buffer")
Cc: Peter Hurley <peter@hurleysoftware.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jirislaby@kernel.org>
Reviewed-and-tested-by: Daniel Gibson <daniel@gibson.sh>
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Daniel Gibson <daniel@gibson.sh>
Link: https://lore.kernel.org/r/20220329235810.452513-2-daniel@gibson.shSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This is needed for the Renesas RZ/V2M (r9a09g011) SoC.
Signed-off-by: Phil Edworthy <phil.edworthy@renesas.com>
Reviewed-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20220330154024.112270-6-phil.edworthy@renesas.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The Renesas RZ/V2M (r9a09g011) SoC uses a uart that is compatible with the
EMMA Mobile SoC.
Signed-off-by: Phil Edworthy <phil.edworthy@renesas.com>
Reviewed-by: Biju Das <biju.das.jz@bp.renesas.com>
Link: https://lore.kernel.org/r/20220330154024.112270-3-phil.edworthy@renesas.comAcked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The lpuart on i.MX93 is derived from i.MX7ULP with some industrial
enhancements, it uses two compatible strings, so update the
compatible string for i.MX93.
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Link: https://lore.kernel.org/r/20220323093659.1722463-1-peng.fan@oss.nxp.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

UniPhier UART controller has a reset lines from system controller.
Add "resets" property to fix the following warning.

  uniphier-ld11-global.dtb: serial@54006800: 'resets' does not match any of the regexes: 'pinctrl-[0-9]+'
      From schema: Documentation/devicetree/bindings/serial/socionext,uniphier-uart.yaml
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Link: https://lore.kernel.org/r/1648617338-8600-3-git-send-email-hayashi.kunihiko@socionext.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

'maxItems' is preferred for a single entry, not 'minItems'.
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Link: https://lore.kernel.org/r/1648617338-8600-2-git-send-email-hayashi.kunihiko@socionext.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Fix the missing clk_disable_unprepare() before return
from owl_uart_probe() in the error handling case.

Fixes: abf42d2f ("tty: serial: owl: add "much needed" clk_prepare_enable()")
Signed-off-by: Miaoqian Lin <linmq006@gmail.com>
Link: https://lore.kernel.org/r/20220307105135.11698-1-linmq006@gmail.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The console_write and IRQ handler can run concurrently.
Problems may occurs console_write is continuously executed while
the IRQ handler is running.
Reviewed-by: Jiri Slaby <jirislaby@kernel.org>
Signed-off-by: Jaewon Kim <jaewon02.kim@samsung.com>
Link: https://lore.kernel.org/r/20220407071619.102249-2-jaewon02.kim@samsung.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

When pci_read_config_dword failed, call pci_release_regions() and
pci_disable_device() to recycle the resource previously allocated.
Reviewed-by: Jiri Slaby <jirislaby@kernel.org>
Signed-off-by: Huang Guobin <huangguobin4@huawei.com>
Link: https://lore.kernel.org/r/20220331091005.3290753-1-huangguobin4@huawei.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

powerpc's asm/prom.h brings some headers that it doesn't
need itself.

In order to clean it up, first add missing headers in
users of asm/prom.h
Reviewed-by: Jiri Slaby <jirislaby@kernel.org>
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Link: https://lore.kernel.org/r/49fc0d4b6446da630b1e9f29c4bab38f8ed087bf.1648833419.git.christophe.leroy@csgroup.euSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

powerpc's asm/prom.h brings some headers that it doesn't
need itself.

In order to clean it up, first add missing headers in
users of asm/prom.h
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Link: https://lore.kernel.org/r/8b3dbd25bbeb7949e1b0a2170fee7b9cc5a6f806.1648833418.git.christophe.leroy@csgroup.euSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

In goldfish_tty_probe(), the port initialized through tty_port_init()
should be destroyed in error paths.In goldfish_tty_remove(), qtty->port
also should be destroyed or else might leak resources.

Fix the above by calling tty_port_destroy().

Fixes: 666b7793 ("goldfish: tty driver")
Reviewed-by: Jiri Slaby <jirislaby@kernel.org>
Signed-off-by: Wang Weiyang <wangweiyang2@huawei.com>
Link: https://lore.kernel.org/r/20220328115844.86032-1-wangweiyang2@huawei.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

altera_jtaguart_tx_chars() duplicates what altera_jtaguart_stop_tx()
already does. So instead of the duplication, call the helper instead.

Not only it makes the code cleaner, but it also says what the "if"
really does.

Cc: Tobias Klauser <tklauser@distanz.ch>
Acked-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20220411104506.8990-4-jslaby@suse.czSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Flow control characters should be sent even if the TX is stopped. So fix
owl-uart to behave the same as other drivers.

This unification also allows the use of the TX helper in the future.

Cc: "Andreas Färber" <afaerber@suse.de>
Cc: Manivannan Sadhasivam <mani@kernel.org>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20220411104506.8990-3-jslaby@suse.czSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The code now contains:
 #ifdef CONFIG_PPC_MPC512x
 ...
 #endif

 #ifdef CONFIG_PPC_MPC512x
 ...
 #endif

So remove the endif+ifdef from the middle, provided it's about the same
define.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20220411104506.8990-2-jslaby@suse.czSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

When the driver fails at alloc_hdlcdev(), and then we remove the driver
module, we will get the following splat:

[   25.065966] general protection fault, probably for non-canonical address 0xdffffc0000000182: 0000 [#1] PREEMPT SMP KASAN PTI
[   25.066914] KASAN: null-ptr-deref in range [0x0000000000000c10-0x0000000000000c17]
[   25.069262] RIP: 0010:detach_hdlc_protocol+0x2a/0x3e0
[   25.077709] Call Trace:
[   25.077924]  <TASK>
[   25.078108]  unregister_hdlc_device+0x16/0x30
[   25.078481]  slgt_cleanup+0x157/0x9f0 [synclink_gt]

Fix this by checking whether the 'info->netdev' is a null pointer first.
Reviewed-by: Jiri Slaby <jirislaby@kernel.org>
Signed-off-by: Zheyu Ma <zheyuma97@gmail.com>
Link: https://lore.kernel.org/r/20220410114814.3920474-1-zheyuma97@gmail.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Reformat the whole document, so that automatic numbering and TOC is
properly generated.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20220411110143.10019-7-jslaby@suse.czSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

All of the URLs give 404. There is a little point to preserve them. If
really need be, we could try archive.org if the documents are not there
by a chance.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20220411110143.10019-6-jslaby@suse.czSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

It is a tty_driver, not serial -- uart_driver. So move it to the tty
docs dir too. (The same as the driver itself.)
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20220411110143.10019-5-jslaby@suse.czSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

We have n_tty documented in Documentation/driver-api/tty/. n_gsm belongs
there too, so move from serial/ to tty/ too.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20220411110143.10019-4-jslaby@suse.czSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

So far only n_tty belongs here, but in the next patches, more will come.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20220411110143.10019-3-jslaby@suse.czSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Based on discussion starting as 87mthw2o93.fsf@meer.lwn.net, let's move
the tty documentation to driver-api. It's more appropriate there.

Cc: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20220411110143.10019-2-jslaby@suse.czSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Pull serial driver fix from Greg KH:
 "This is a single serial driver fix for a build issue that showed up
  due to changes that came in through the tty tree in 5.18-rc1 that were
  missed previously. It resolves a build error with the mpc52xx_uart
  driver.

  It has been in linux-next this week with no reported problems"

* tag 'tty-5.18-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
  tty: serial: mpc52xx_uart: make rx/tx hooks return unsigned, part II.

Pull staging driver fix from Greg KH:
 "Here is a single staging driver fix for 5.18-rc2 that resolves an
  endian issue for the r8188eu driver. It has been in linux-next all
  this week with no reported problems"

* tag 'staging-5.18-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
  staging: r8188eu: Fix PPPoE tag insertion on little endian systems

Merge tag 'driver-core-5.18-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core

Pull driver core updates from Greg KH:
 "Here are two small driver core changes for 5.18-rc2.

  They are the final bits in the removal of the default_attrs field in
  struct kobj_type. I had to wait until after 5.18-rc1 for all of the
  changes to do this came in through different development trees, and
  then one new user snuck in. So this series has two changes:

   - removal of the default_attrs field in the powerpc/pseries/vas code.

     The change has been acked by the PPC maintainers to come through
     this tree

   - removal of default_attrs from struct kobj_type now that all
     in-kernel users are removed.

     This cleans up the kobject code a little bit and removes some
     duplicated functionality that confused people (now there is only
     one way to do default groups)

  Both of these have been in linux-next for all of this week with no
  reported problems"

* tag 'driver-core-5.18-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core:
  kobject: kobj_type: remove default_attrs
  powerpc/pseries/vas: use default_groups in kobj_type

Pull char/misc driver fix from Greg KH:
 "A single driver fix. It resolves the build warning issue on 32bit
  systems in the habannalabs driver that came in during the 5.18-rc1
  merge cycle.

  It has been in linux-next for all this week with no reported problems"

* tag 'char-misc-5.18-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
  habanalabs: Fix test build failures

Pull powerpc fixes from Michael Ellerman:

 - Fix KVM "lost kick" race, where an attempt to pull a vcpu out of the
   guest could be lost (or delayed until the next guest exit).

 - Disable SCV (system call vectored) when PR KVM guests could be run.

 - Fix KVM PR guests using SCV, by disallowing AIL != 0 for KVM PR
   guests.

 - Add a new KVM CAP to indicate if AIL == 3 is supported.

 - Fix a regression when hotplugging a CPU to a memoryless/cpuless node.

 - Make virt_addr_valid() stricter for 64-bit Book3E & 32-bit, which
   fixes crashes seen due to hardened usercopy.

 - Revert a change to max_mapnr which broke HIGHMEM.

Thanks to Christophe Leroy, Fabiano Rosas, Kefeng Wang, Nicholas Piggin,
and Srikar Dronamraju.

* tag 'powerpc-5.18-2' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
  Revert "powerpc: Set max_mapnr correctly"
  powerpc: Fix virt_addr_valid() for 64-bit Book3E & 32-bit
  KVM: PPC: Move kvmhv_on_pseries() into kvm_ppc.h
  powerpc/numa: Handle partially initialized numa nodes
  powerpc/64: Fix build failure with allyesconfig in book3s_64_entry.S
  KVM: PPC: Use KVM_CAP_PPC_AIL_MODE_3
  KVM: PPC: Book3S PR: Disallow AIL != 0
  KVM: PPC: Book3S PR: Disable SCV when AIL could be disabled
  KVM: PPC: Book3S HV P9: Fix "lost kick" race

Pull irq fixes from Thomas Gleixner:
 "A set of interrupt chip driver fixes:

   - A fix for a long standing bug in the ARM GICv3 redistributor
     polling which uses the wrong bit number to test.

   - Prevent translation of bogus ACPI table entries which map device
     interrupts into the IPI space on ARM GICs.

   - Don't write into the pending register of ARM GICV4 before the scan
     in hardware has completed.

   - A set of build and correctness fixes for the Qualcomm MPM driver"

* tag 'irq-urgent-2022-04-10' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  irqchip/gic, gic-v3: Prevent GSI to SGI translations
  irqchip/gic-v3: Fix GICR_CTLR.RWP polling
  irqchip/gic-v4: Wait for GICR_VPENDBASER.Dirty to clear before descheduling
  irqchip/irq-qcom-mpm: fix return value check in qcom_mpm_init()
  irq/qcom-mpm: Fix build error without MAILBOX

Pull x86 fixes from Borislav Petkov:

 - Fix the MSI message data struct definition

 - Use local labels in the exception table macros to avoid symbol
   conflicts with clang LTO builds

 - A couple of fixes to objtool checking of the relatively newly added
   SLS and IBT code

 - Rename a local var in the WARN* macro machinery to prevent shadowing

* tag 'x86_urgent_for_v5.18_rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/msi: Fix msi message data shadow struct
  x86/extable: Prefer local labels in .set directives
  x86,bpf: Avoid IBT objtool warning
  objtool: Fix SLS validation for kcov tail-call replacement
  objtool: Fix IBT tail-call detection
  x86/bug: Prevent shadowing in __WARN_FLAGS
  x86/mm/tlb: Revert retpoline avoidance approach

Pull perf fixes from Borislav Petkov:

 - A couple of fixes to cgroup-related handling of perf events

 - A couple of fixes to event encoding on Sapphire Rapids

 - Pass event caps of inherited events so that perf doesn't fail wrongly
   at fork()

 - Add support for a new Raptor Lake CPU

* tag 'perf_urgent_for_v5.18_rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  perf/core: Always set cpuctx cgrp when enable cgroup event
  perf/core: Fix perf_cgroup_switch()
  perf/core: Use perf_cgroup_info->active to check if cgroup is active
  perf/core: Don't pass task around when ctx sched in
  perf/x86/intel: Update the FRONTEND MSR mask on Sapphire Rapids
  perf/x86/intel: Don't extend the pseudo-encoding to GP counters
  perf/core: Inherit event_caps
  perf/x86/uncore: Add Raptor Lake uncore support
  perf/x86/msr: Add Raptor Lake CPU support
  perf/x86/cstate: Add Raptor Lake support
  perf/x86: Add Intel Raptor Lake support

Pull locking fixes from Borislav Petkov:

 - Allow the compiler to optimize away unused percpu accesses and change
   the local_lock_* macros back to inline functions

 - A couple of fixes to static call insn patching

* tag 'locking_urgent_for_v5.18_rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  Revert "mm/page_alloc: mark pagesets as __maybe_unused"
  Revert "locking/local_lock: Make the empty local_lock_*() function a macro."
  x86/percpu: Remove volatile from arch_raw_cpu_ptr().
  static_call: Remove __DEFINE_STATIC_CALL macro
  static_call: Properly initialise DEFINE_STATIC_CALL_RET0()
  static_call: Don't make __static_call_return0 static
  x86,static_call: Fix __static_call_return0 for i386

Pull scheduler fixes from Borislav Petkov:

 - Use the correct static key checking primitive on the IRQ exit path

 - Two fixes for the new forceidle balancer

* tag 'sched_urgent_for_v5.18_rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  entry: Fix compile error in dynamic_irqentry_exit_cond_resched()
  sched: Teach the forced-newidle balancer about CPU affinity limitation.
  sched/core: Fix forceidle balancing

Merge tag 'perf-tools-fixes-for-v5.18-2022-04-09' of git://git.kernel.org/pub/scm/linux/kernel/git/acme/linux

Pull perf tools fixes from Arnaldo Carvalho de Melo:

 - Fix the clang command line option probing and remove some options to
   filter out, fixing the build with the latest clang versions

 - Fix 'perf bench' futex and epoll benchmarks to deal with machines
   with more than 1K CPUs

 - Fix 'perf test tsc' error message when not supported

 - Remap perf ring buffer if there is no space for event, fixing perf
   usage in 32-bit ChromeOS

 - Drop objdump stderr to avoid getting stuck waiting for stdout output
   in 'perf annotate'

 - Fix up garbled output by now showing unwind error messages when
   augmenting frame in best effort mode

 - Fix perf's libperf_print callback, use the va_args eprintf() variant

 - Sync vhost and arm64 cputype headers with the kernel sources

 - Fix 'perf report --mem-mode' with ARM SPE

 - Add missing external commands ('iiostat', etc) to 'perf --list-cmds'

* tag 'perf-tools-fixes-for-v5.18-2022-04-09' of git://git.kernel.org/pub/scm/linux/kernel/git/acme/linux:
  perf annotate: Drop objdump stderr to avoid getting stuck waiting for stdout output
  perf tools: Add external commands to list-cmds
  perf docs: Add perf-iostat link to manpages
  perf session: Remap buf if there is no space for event
  perf bench: Fix epoll bench to correct usage of affinity for machines with #CPUs > 1K
  perf bench: Fix futex bench to correct usage of affinity for machines with #CPUs > 1K
  perf tools: Fix perf's libperf_print callback
  perf: arm-spe: Fix perf report --mem-mode
  perf unwind: Don't show unwind error messages when augmenting frame pointer stack
  tools headers arm64: Sync arm64's cputype.h with the kernel sources
  perf test tsc: Fix error message when not supported
  perf build: Don't use -ffat-lto-objects in the python feature test when building with clang-13
  perf python: Fix probing for some clang command line options
  tools build: Filter out options and warnings not supported by clang
  tools build: Use $(shell ) instead of `` to get embedded libperl's ccopts
  tools include UAPI: Sync linux/vhost.h with the kernel sources

Pull cxl and nvdimm fixes from Dan Williams:

 - Fix a compile error in the nvdimm unit tests

 - Fix a shadowed variable warning in the CXL PCI driver

* tag 'cxl+nvdimm-for-5.18-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm:
  cxl/pci: Drop shadowed variable
  tools/testing/nvdimm: Fix security_init() symbol collision

Pull gpio fix from Bartosz Golaszewski:

 - fix a race condition with consumers accessing the fields of GPIO IRQ
   chips before they're fully initialized

* tag 'gpio-fixes-for-v5.18-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux:
  gpio: Restrict usage of GPIO chip irq members before initialization