It addresses the timeout parameter in the tiglusb driver.

1.  timeout could be 0, causing a divide-by-zero.
The patch prevents this.

2.  The timeout value to usb_bulk_msg() could be rounded
down to cause a divide-by-zero if timeout was < 10, e.g. 9,
in:
	result = usb_bulk_msg (s->dev, pipe, buffer, bytes_to_read,
			       &bytes_read, HZ / (timeout / 10));
9 / 10 == 0 => divide-by-zero !!

3.  The timeout value above doesn't do very well on converting
timeout to tenths of seconds.  Even for the default timeout
value of 15 (1.5 seconds), it becomes:
	HZ / (15 / 10) == HZ / 1 == HZ, or 1 second.
The patch corrects this formula to use:
	(HZ * 10) / timeout

Here is a patch that fixes the disconnect handling and locking for the
vicam driver. It does the following.

1.)	Change the parameters of send_control_msg to take a struct
	vicam_camera instead of struct usb_device to allow for locking
	of the device. Note that __send_control_msg does not lock the
	camera. send_control_msg locks the camera before calling
	__send_control_msg.
2.)	Remove all instances of busy_lock. busy_lock was renamed to
	cam_lock and used to lock out simultaneous uses of the camera
	and handle disconnects. We may want to add back a different lock
	to handle smp type stuff.
3.)	Separate read_frame and vicam_decode_color. This should move us
	along toward asynchronous urbs.

This patch does not address the locking of the camera that is still
needed by the proc interface.

Thanks to Ralf Dietrich <ralle@envicon.de> for the information.

fixes bug #26 <http://bugme.osdl.org/show_bug.cgi?id=26>

Description: When an urb has been submitted via usbdevfs, and is still
pending when the interface it was submitted to is released, force the
urb to be completed.  This is the correct behaviour.  It fixes an oops on
system shutdown when using the user space driver for the speedtouch
modem.

this fixes an uninitialzed spinlock in ipaq.c. the driver should work
on smp machines now.

When chasing down some of those 'bad entry' diagnostics, I once
got suspicious that the problem was slab corruption coming from
the way the td hashtable code worked.   So I put together this
patch, eliminating some kmallocation, and the next times I ran
that test, the oops went away and it worked like a charm.  Hmm.

This patch is good because it shrinks memory and code, and gets
rid of some could-fail allocations, so I figured I'd send it on
(low priority) even if I don't think it fixes the root problem.

Basically, no point in having short and long timeout options
where both are _shorter_ than the timeout from the USB spec.

Hotplug agents couldn't use /sys/$DEVPATH after /sys/root
morphed into /sys/devices ... now they can do it again.

into penguin.transmeta.com:/home/penguin/torvalds/repositories/kernel/linux

Fix compilation errors for do_fork() and print_symbol()

into penguin.transmeta.com:/home/penguin/torvalds/repositories/kernel/linux

Implements a new set of block address_space_operations which will never
attach buffer_heads to file pagecache.  These can be turned on for ext2
with the `nobh' mount option.

During write-intensive testing on a 7G machine, total buffer_head
storage remained below 0.3 megabytes.  And those buffer_heads are
against ZONE_NORMAL pagecache and will be reclaimed by ZONE_NORMAL
memory pressure.

This work is, of course, a special for the huge highmem machines.
Possibly it obsoletes the buffer_heads_over_limit stuff (which doesn't
work terribly well), but that code is simple, and will provide relief
for other filesystems.


It should be noted that the nobh_prepare_write() function and the
PageMappedToDisk() infrastructure is what is needed to solve the
problem of user data corruption when the filesystem which backs a
sparse MAP_SHARED mapping runs out of space.  We can use this code in
filemap_nopage() to ensure that all mapped pages have space allocated
on-disk.  Deliver SIGBUS on ENOSPC.

This will require a new address_space op, I expect.

This patch is a general solution to the situation where a zone is full
of pinned pages.

This can come about if:

a) Someone has allocated all of ZONE_DMA for IO buffers

b) Some application is mlocking some memory and a zone ends up full
   of mlocked pages (can happen on a 1G ia32 system)

c) All of ZONE_HIGHMEM is pinned in hugetlb pages (can happen on 1G
   machines)

We'll currently burn 10% of CPU in kswapd when this happens, although
it is quite hard to trigger.

The algorithm is:

- If page reclaim has scanned 2 * the total number of pages in the
  zone and there have been no pages freed in that zone then mark the
  zone as "all unreclaimable".

- When a zone is "all unreclaimable" page reclaim almost ignores it.
  We will perform a "light" scan at DEF_PRIORITY (typically 1/4096'th of
  the zone, or 64 pages) and then forget about the zone.

- When a batch of pages are freed into the zone, clear its "all
  unreclaimable" state and start full scanning again.  The assumption
  being that some state change has come about which will make reclaim
  successful again.

  So if a "light scan" actually frees some pages, the zone will revert to
  normal state immediately.

So we're effectively putting the zone into "low power" mode, and lightly
polling it to see if something has changed.

The code works OK, but is quite hard to test - I mainly tested it by
pinning all highmem in hugetlb pages.

Strengthen the `incremental min' logic in the page allocator.

Currently it is allowing the allocation to succeed if the zone has
free_pages >= pages_high.

This was to avoid a lockup corner case in which all the zones were at
pages_high so reclaim wasn't doing anything, but the incremental min
refused to take pages from those zones anyway.

But we want the incremental min zone protection to work.  So:

- Only allow the allocator to dip below the incremental min if he
  cannot run direct reclaim.

- Change the page reclaim code so that on the direct reclaim path,
  the caller can free pages beyond ->pages_high.  So if the incremental
  min test fails, the caller will go and free some more memory.

  Eventually, the caller will have freed enough memory for the
  incremental min test to pass against one of the zones.

The vm_writeback address_space operation was designed to provide the VM
with a "clustered writeout" capability.  It allowed the filesystem to
perform more intelligent writearound decisions when the VM was trying
to clean a particular page.

I can't say I ever saw any real benefit from this - not much writeout
actually happens on that path - quite a lot of work has gone into
minimising it actually.

The default ->vm_writeback a_op which I provided wrote back the pages
in ->dirty_pages order.  But there is one scenario in which this causes
problems - writing a single 4G file with mem=4G.  We end up with all of
ZONE_NORMAL full of dirty pages, but all writeback effort is against
highmem pages.  (Because there is about 1.5G of dirty memory total).

Net effect: the machine stalls ZONE_NORMAL allocation attempts until
the ->dirty_pages writeback advances onto ZONE_NORMAL pages.

This can be fixed most sweetly with additional radix-tree
infrastructure which will be quite complex.  Later.


So this patch dumps it all, and goes back to using writepage
against individual pages as they come off the LRU.

blk_congestion_wait() is a utility function which various callers use
to throttle themselves to the rate at which the IO system can retire
writes.

The current implementation refuses to wait if no queues are "congested"
(>75% of requests are in flight).

That doesn't work if the queue is so huge that it can hold more than
40% (dirty_ratio) of memory.  The queue simply cannot enter congestion
because the VM refuses to allow more than 40% of memory to be dirtied.
(This spin could happen with a lot of normal-sized queues too)

So this patch simply changes blk_congestion_wait() to throttle even if
there are no congested queues.  It will cause the caller to sleep until
someone puts back a write request against any queue.  (Nobody uses
blk_congestion_wait for read congestion).

The patch adds new state to backing_dev_info->state: a couple of flags
which indicate whether there are _any_ reads or writes in flight
against that queue.  This was added to prevent blk_congestion_wait()
from taking a nap when there are no writes at all in flight.

But the "are there any reads" info could be used to defer background
writeout from pdflush, to reduce read-vs-write competition.  We'll see.

Because the large request queues have made a fundamental change:
blocking in get_request_wait() has been the main form of VM throttling
for years.  But with large queues it doesn't work any more - all
throttling happens in blk_congestion_wait().

Also, change io_schedule_timeout() to propagate the schedule_timeout()
return value.  I was using that in some debug code, but it should have
been like that from day one.

From Roman Zippel.  Don't assume that physical memory starts at
physical address zero.

Patch from Stephen Tweedie

"In looking at the fix for the ext3 Orlov double-accounting bug, I
 noticed a change to the sb->s_dir_count accounting, restoring a
 missing s_dir_count++ when we allocate a new directory.

 However, I can't find anywhere in the code where we decrement this
 again on directory deletion, neither in ext2 nor in ext3, in 2.4 nor
 in 2.5."

Locking is via lock_super().

There is a warning in there to detect when block_write_full_page()
attaches buffers to a blockdev page.  This is a bad thing because that
page's blocks may then overlap blocks from a different address_space.
So I disallowed it.

But the message can be triggered when an application is mmapping a
blockdev MAP_SHARED.  Apparently INND likes to do this.

So remove the warning.

Patch from Christopher Li <chrisl@vmware.com>

This little patch will fix two place in htree code which
forget the "cpu_to_le16" converting . This bug causes
incorrect record length on PPC.

Thanks Franz for report the problem.

Patch from Andreas Gruenbacher <agruen@suse.de>

The setxattr inode operation is defined like this in 2.4 and 2.5:

        int (*setxattr) (struct dentry *dentry, const char *name,
                         void *value, size_t size, int flags);

the original type of the value parameter was `const void *'; the const
obviously has been lost at some point. The definition should be:

        int (*setxattr) (struct dentry *dentry, const char *name,
                         const void *value, size_t size, int flags);

The page allocator has traditionally just gone BUG when it sees a page
in a bad state.  This is usually due to hardware errors, sometimes
software errors.

I'm proposing that we not go BUG() any more, but print lots (and lots)
of diagnostic info and try to continue.

Might be a bit controversial.

balance_dirty_pages() is too expensive to call once-per-page.  Use the
ratelimited version.

From Dipanker Sarma.

Before setting the ids->entries to the new array, there must be a wmb()
to make sure that the memcpyed contents of the new array are visible
before the new array becomes visible.

This patch fixes a problem which was discovered by Vladimir Saveliev
<vs@namesys.com>

Radix trees have a `height' field, which defines how far the pages are
from the root of the tree.  It starts out at zero and increases as the
trees depth is grown.

But it is never decreased.  It cannot be decreased without a full tree
traversal.

Because radix_tree_delete() does not decrease `height', we end up
returning inodes to their filesystem's inode slab cache with a non-zero
height.

And when that inode is reused from slab for a new file, it still has a
non-zero height.  So we're breaking the slab rules by not putting
objects back in a fully reinitialised state.

So the new file starts out life with whatever height the previous owner
of the inode had.  Which is space- and speed-inefficient.

The most efficient place to fix this would be in destroy_inode().  But
that only fixes the problem for inodes - there are other users of radix
trees.

So fix it in radix_tree_delete(): if the tree was emptied, reset
`height' to zero.

Patch from Hugh Dickins <hugh@veritas.com>

Fixes the Oracle startup problem reported by Alessandro Suardi.

Reverts a "simplification" to shmdt() which was wrong if subsequent
mprotects broke up the original VMA, or if parts of it were munmapped.

- I hit a BUG in end_swap_bio_read() under heavy load.  The page
  wasn't locked.  No idea how this can happen :(

  Add a BUG at submission time to catch a caller reading into an
  unlocked swapcache page.

- Remove a debug check from destroy_inode() - it was in the wrong leg
  of the `if' statement anyway.

This allows NFSv4 responses to cover move than one page.  There are
still limits though.  There can be at most one 'data' response which
includes READ, READLINK, READDIR.  For these responses, the interesting
data goes in a separate page or, for READ, list of pages.

All responses before the 'data' response must fit in one page, and all
responses after it must also fit in one (separate) page.

Now that nfsd uses a list of pages for requests instead of
one large buffer, NFSv4 need to know about this.

The most interesting part of this is that it is possible
that section of a request, like a path name, could span
two pages, so we need to be able to kmalloc as little bit
of space to copy them into, and make sure they get
freed later.

We don't implement the ancient stat syscalls on ppc64 since early libcs
wont run on ppc64 (they hardcode the incorrect cacheline size).

into penguin.transmeta.com:/home/penguin/torvalds/repositories/kernel/linux

into penguin.transmeta.com:/home/penguin/torvalds/repositories/kernel/linux

Here is the a pre-patch in the attempt to get rid of 'struct
nfs4_compound', and the associated horrible union in 'struct
nfs4_op'.

It splits out the fields that are meant to do buffer overflow checking
and iovec adjusting on the XDR received/sent data. It moves support
for that nto the dedicated structure 'xdr_stream', and the associated
functions 'xdr_reserve_space()', 'xdr_inline_decode()'.

The patch also expands out the all macros ENCODE_HEAD, ENCODE_TAIL,
ADJUST_ARGS and DECODE_HEAD, as well as most of the DECODE_TAILs.