- 14 Aug, 2023 3 commits
-
-
Arnd Bergmann authored
A while ago I created a2305e3d ("powerpc: mark local variables around longjmp as volatile") in order to allow building powerpc with -Wextra enabled on gcc-11. I tried this again with gcc-13 and found two more of the same issues, presumably based on slightly different optimization paths being taken here: arch/powerpc/xmon/xmon.c:3306:27: error: variable 'mm' might be clobbered by 'longjmp' or 'vfork' [-Werror=clobbered] arch/powerpc/kexec/crash.c:353:22: error: variable 'i' might be clobbered by 'longjmp' or 'vfork' [-Werror=clobbered] I checked a bunch of randconfigs and found only these two, so just address them the same way as the others. Signed-off-by:
Arnd Bergmann <arnd@arndb.de> Signed-off-by:
Michael Ellerman <mpe@ellerman.id.au> Link: https://msgid.link/20230809131024.2039647-1-arnd@kernel.org
-
Yuan Tan authored
Serial is a critical feature for logging and debuging, and the other architectures enable serial by default. Let's enable CONFIG_SERIAL_PMACZILOG and CONFIG_SERIAL_PMACZILOG_CONSOLE by default. Signed-off-by:
Yuan Tan <tanyuan@tinylab.org> Reviewed-by:
Christophe Leroy <christophe.leroy@csgroup.eu> Signed-off-by:
-
Michael Ellerman authored
Merge SMT changes we are sharing with the tip tree.
-
- 02 Aug, 2023 27 commits
-
-
Michael Ellerman authored
Integrate with the generic SMT support, so that when a CPU is DLPAR onlined it is brought up with the correct SMT mode. Signed-off-by:
-
Michael Ellerman authored
Add support for HOTPLUG_SMT, which enables the generic sysfs SMT support files in /sys/devices/system/cpu/smt, as well as the "nosmt" boot parameter. Implement the recently added hooks to allow partial SMT states, allow any number of threads per core. Tie the config symbol to HOTPLUG_CPU, which enables it on the major platforms that support SMT. If there are other platforms that want the SMT support that can be tweaked in future. Signed-off-by:
Laurent Dufour <ldufour@linux.ibm.com> Link: https://msgid.link/20230705145143.40545-10-ldufour@linux.ibm.com
-
Michael Ellerman authored
As part of the generic HOTPLUG_SMT code, there is support for disabling secondary SMT threads at boot time, by passing "nosmt" on the kernel command line. The way that is implemented is the secondary threads are brought partly online, and then taken back offline again. That is done to support x86 CPUs needing certain initialisation done on all threads. However powerpc has similar needs, see commit d70a54e2 ("powerpc/powernv: Ignore smt-enabled on Power8 and later"). For that to work the powerpc CPU hotplug callbacks need to be registered before secondary CPUs are brought online, otherwise __cpu_disable() fails due to smp_ops->cpu_disable being NULL. So split the basic initialisation into pseries_cpu_hotplug_init() which can be called early from setup_arch(). The DLPAR related initialisation can still be done later, because it needs to do allocations. Signed-off-by:
-
Michael Ellerman authored
Merge tag 'smp-core-for-ppc-23-07-28' of https://git.kernel.org/pub/scm/linux/kernel/git/tip/tip into topic/cpu-smt SMP core changes for powerpc
-
Laurent Dufour authored
Function name in the descriptor was not correct. Reported-by:
kernel test robot <lkp@intel.com> Closes: https://lore.kernel.org/oe-kbuild-all/202307251721.bUGcsCeQ-lkp@intel.com/Signed-off-by:
-
Uwe Kleine-König authored
Instead of resorting to BUG() ensure that the driver isn't unbound by suppressing its bind and unbind sysfs attributes. As the driver is built-in there is no way to remove a device once bound. As a nice side effect this allows to drop the remove function. Signed-off-by:
Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Signed-off-by:
-
Arnd Bergmann authored
There are a few warnings in powerpc64 defconfig builds after -Wmissing-prototypes gets promoted from W=1 to the default warning set: arch/powerpc/mm/book3s64/pgtable.c:422:6: error: no previous prototype for 'arch_report_meminfo' [-Werror=missing-prototypes] arch/powerpc/platforms/cell/ras.c:275:5: error: no previous prototype for 'cbe_sysreset_hack' [-Werror=missing-prototypes] arch/powerpc/platforms/cell/spu_manage.c:29:21: error: no previous prototype for 'spu_devnode' [-Werror=missing-prototypes] arch/powerpc/platforms/pasemi/time.c:12:17: error: no previous prototype for 'pas_get_boot_time' [-Werror=missing-prototypes] arch/powerpc/platforms/powermac/feature.c:1532:13: error: no previous prototype for 'g5_phy_disable_cpu1' [-Werror=missing-prototypes] arch/powerpc/platforms/86xx/pic.c:28:13: error: no previous prototype for 'mpc86xx_init_irq' [-Werror=missing-prototypes] drivers/pci/pci-sysfs.c:936:13: error: no previous prototype for 'pci_adjust_legacy_attr' [-Werror=missing-prototypes] Address these by including the right header files or marking the functions static. The audit.c one is a bit tricky since compat_audit.h cannot include regular kernel headers tht have conflicting types on 32-bit powerpc. Signed-off-by:
-
Benjamin Gray authored
While the target is volatile, the temporary variables used to access the target cast away the volatile. This is undefined behaviour, and a compiler may optimise away/reorder these accesses, breaking the test. This was observed with GCC 13.1.1, but it can be difficult to reproduce because of the dependency on compiler behaviour. Signed-off-by:
Benjamin Gray <bgray@linux.ibm.com> Signed-off-by:
-
Benjamin Gray authored
pid_max_addr() searches for the 'pid_max' symbol in /proc/kallsyms, and prints an error if it cannot find it. The error message has a typo, calling it pix_max. Signed-off-by:
-
Benjamin Gray authored
Many tests require specific hardware features/configurations that a typical machine might not have. As a result, it's common to see a test is skipped. But it is tedious to find out why a test is skipped when all it gives is the file location of the skip macro. Convert SKIP_IF() to SKIP_IF_MSG(), with appropriate descriptions of why the test is being skipped. This gives a general idea of why a test is skipped, which can be looked into further if it doesn't make sense. Signed-off-by:
-
Rob Herring authored
The DT of_device.h and of_platform.h date back to the separate of_platform_bus_type before it as merged into the regular platform bus. As part of that merge prepping Arm DT support 13 years ago, they "temporarily" include each other. They also include platform_device.h and of.h. As a result, there's a pretty much random mix of those include files used throughout the tree. In order to detangle these headers and replace the implicit includes with struct declarations, users need to explicitly include the correct includes. Signed-off-by:
Rob Herring <robh@kernel.org> [mpe: Fixup maple/setup.c which needs platform_device] Signed-off-by:
-
Nicholas Piggin authored
This performs lazy tlb mm shootdown when doing the exit TLB flush when all mm users go away and user mappings are removed, which avoids having to do the lazy tlb mm shootdown IPIs on the final mmput when all kernel references disappear. powerpc/64s uses a broadcast TLBIE for the exit TLB flush if remote CPUs need to be invalidated (unless TLBIE is disabled), so this doesn't necessarily save IPIs but it does avoid a broadcast TLBIE which is quite expensive. Signed-off-by:
Nicholas Piggin <npiggin@gmail.com> [mpe: Squash in preempt_disable/enable() fix from Nick] Signed-off-by:
-
Nicholas Piggin authored
When context switching away from an mm, add a CONFIG_DEBUG_VM warning check to ensure this CPU is still set in the mask. This could catch bugs where the mask is improperly trimmed while the CPU is still using the mm. Signed-off-by:
-
Nicholas Piggin authored
Avoid open-coded atomic_dec on mm->context.active_cpus and use the function made for it. Add CONFIG_DEBUG_VM underflow checking on the counter. Signed-off-by:
-
Nicholas Piggin authored
init_mm mm_cpumask and context.active_cpus is not maintained at boot and hotplug. This seems to be harmless because init_mm does not have a userspace and so never gets user TLBs flushed, but it looks odd and it prevents some sanity checks being added. Signed-off-by:
-
Michael Ellerman authored
Enable all the acclerated crypto algorithms as modules in the 64-bit defconfig, to get more test coverage. Signed-off-by:
-
Omar Sandoval authored
None of the other accelerated crypto modules are built by default. Signed-off-by:
Omar Sandoval <osandov@fb.com> Signed-off-by:
-
Omar Sandoval authored
My stripped down configuration fails to build with: ERROR: modpost: "skcipher_walk_aead_encrypt" [arch/powerpc/crypto/aes-gcm-p10-crypto.ko] undefined! ERROR: modpost: "skcipher_walk_done" [arch/powerpc/crypto/aes-gcm-p10-crypto.ko] undefined! ERROR: modpost: "skcipher_walk_aead_decrypt" [arch/powerpc/crypto/aes-gcm-p10-crypto.ko] undefined! Fix it by selecting CRYPTO_SKCIPHER. Signed-off-by:
-
Christophe Leroy authored
To avoid a useless nop on top of every uaccess enable/disable and make life easier for objtool, replace static branches by ASM feature fixups that will nop KUAP enabling instructions out in the unlikely case KUAP is disabled at boottime. Leave it as is on book3s/64 for now, it will be handled later when objtool is activated on PPC64. Signed-off-by:
-
Christophe Leroy authored
Objtool reports following warnings: arch/powerpc/kernel/signal_32.o: warning: objtool: __prevent_user_access.constprop.0+0x4 (.text+0x4): redundant UACCESS disable arch/powerpc/kernel/signal_32.o: warning: objtool: user_access_begin+0x2c (.text+0x4c): return with UACCESS enabled arch/powerpc/kernel/signal_32.o: warning: objtool: handle_rt_signal32+0x188 (.text+0x360): call to __prevent_user_access.constprop.0() with UACCESS enabled arch/powerpc/kernel/signal_32.o: warning: objtool: handle_signal32+0x150 (.text+0x4d4): call to __prevent_user_access.constprop.0() with UACCESS enabled This is due to some KUAP enabling/disabling functions being outline allthough they are marked inline. Use __always_inline instead. Signed-off-by: -
Christophe Leroy authored
On book3s/32 KUAP is performed at segment level. At the moment, when enabling userspace access, only current segment is modified. Then if a write is performed on another user segment, a fault is taken and all other user segments get enabled for userspace access. This then require special attention when disabling userspace access. Having a userspace write access crossing a segment boundary is unlikely. Having a userspace write access crossing a segment boundary back and forth is even more unlikely. So, instead of enabling userspace access on all segments when a write fault occurs, just change which segment has userspace access enabled in order to eliminate the case when more than one segment has userspace access enabled. That simplifies userspace access deactivation. There is however a corner case which is even more unlikely but has to be handled anyway: an unaligned access which is crossing a segment boundary. That would definitely require at least having userspace access enabled on the two segments. To avoid complicating the likely case for a so unlikely happening, handle such situation like an alignment exception and emulate the store. Signed-off-by:
-
Christophe Leroy authored
All but book3s/64 use a static branch key for disabling kuap. book3s/64 uses an mmu feature. Refactor all targets to use MMU_FTR_KUAP like book3s/64. For PPC32 that implies updating mmu features fixups once KUAP has been initialised. Signed-off-by:
-
Christophe Leroy authored
In order to reuse MMU_FTR_BOOK3S_KUAP for other targets than BOOK3S, rename it MMU_FTR_KUAP. Signed-off-by:
-
Christophe Leroy authored
On powerpc32, features fixup is performed very early and that's too early to read the cmdline and take into account 'nosmap' parameter. On the other hand, no userspace access is performed that early and KUAP feature fixup can be performed later. Add a function to update mmu features. The function is passed a mask with the features that can be updated. Signed-off-by:
-
Christophe Leroy authored
kuep_is_disabled() was introduced by commit 91bb3082 ("powerpc/32s: Refactor update of user segment registers") but then all users but one were removed by commit 526d4a4c ("powerpc/32s: Do kuep_lock() and kuep_unlock() in assembly"). Fold kuep_is_disabled() into init_new_context() which is its only user. Signed-off-by:
-
Christophe Leroy authored
Disassembly of interrupt_enter_prepare() shows a pointless nop before the mftb c000abf0 <interrupt_enter_prepare>: c000abf0: 81 23 00 84 lwz r9,132(r3) c000abf4: 71 29 40 00 andi. r9,r9,16384 c000abf8: 41 82 00 28 beq- c000ac20 <interrupt_enter_prepare+0x30> c000abfc: ===> 60 00 00 00 nop <==== c000ac00: 7d 0c 42 e6 mftb r8 c000ac04: 80 e2 00 08 lwz r7,8(r2) c000ac08: 81 22 00 28 lwz r9,40(r2) c000ac0c: 91 02 00 24 stw r8,36(r2) c000ac10: 7d 29 38 50 subf r9,r9,r7 c000ac14: 7d 29 42 14 add r9,r9,r8 c000ac18: 91 22 00 08 stw r9,8(r2) c000ac1c: 4e 80 00 20 blr c000ac20: 60 00 00 00 nop c000ac24: 7d 5a c2 a6 mfmd_ap r10 c000ac28: 3d 20 de 00 lis r9,-8704 c000ac2c: 91 43 00 b0 stw r10,176(r3) c000ac30: 7d 3a c3 a6 mtspr 794,r9 c000ac34: 4e 80 00 20 blr That comes from the call to kuap_loc(), allthough __kuap_lock() is an empty function on the 8xx. To avoid that, only perform kuap_is_disabled() check when there is something to do with __kuap_lock(). Do the same with __kuap_save_and_lock() and __kuap_get_and_assert_locked(). Signed-off-by:
-
Christophe Leroy authored
A disassembly of interrupt_exit_kernel_prepare() shows a useless read of MD_AP register. This is shown by r9 being re-used immediately without doing anything with the value read. c000e0e0: 60 00 00 00 nop c000e0e4: ===> 7d 3a c2 a6 mfmd_ap r9 <==== c000e0e8: 7d 20 00 a6 mfmsr r9 c000e0ec: 7c 51 13 a6 mtspr 81,r2 c000e0f0: 81 3f 00 84 lwz r9,132(r31) c000e0f4: 71 29 80 00 andi. r9,r9,32768 kuap_get_and_assert_locked() is paired with kuap_kernel_restore() and are only used in interrupt_exit_kernel_prepare(). The value returned by kuap_get_and_assert_locked() is only used by kuap_kernel_restore(). On 8xx, kuap_kernel_restore() doesn't use the value read by kuap_get_and_assert_locked() so modify kuap_get_and_assert_locked() to not perform the read of MD_AP and return 0 instead. The same applies on BOOKE. Signed-off-by:
-
- 28 Jul, 2023 7 commits
-
-
Michael Ellerman authored
Add support to the /sys/devices/system/cpu/smt/control interface for enabling a specified number of SMT threads per core, including partial SMT states where not all threads are brought online. The current interface accepts "on" and "off", to enable either 1 or all SMT threads per core. This commit allows writing an integer, between 1 and the number of SMT threads supported by the machine. Writing 1 is a synonym for "off", 2 or more enables SMT with the specified number of threads. When reading the file, if all threads are online "on" is returned, to avoid changing behaviour for existing users. If some other number of threads is online then the integer value is returned. Architectures like x86 only supporting 1 thread or all threads, should not define CONFIG_SMT_NUM_THREADS_DYNAMIC. Architecture supporting partial SMT states, like PowerPC, should define it. [ ldufour: Slightly reword the commit's description ] [ ldufour: Remove switch() in __store_smt_control() ] [ ldufour: Rix build issue in control_show() ] Reported-by:
Thomas Gleixner <tglx@linutronix.de> Tested-by:
Zhang Rui <rui.zhang@intel.com> Link: https://lore.kernel.org/r/20230705145143.40545-8-ldufour@linux.ibm.com
-
Michael Ellerman authored
Some architectures allows partial SMT states, i.e. when not all SMT threads are brought online. To support that, add an architecture helper which checks whether a given CPU is allowed to be brought online depending on how many SMT threads are currently enabled. Since this is only applicable to architecture supporting partial SMT, only these architectures should select the new configuration variable CONFIG_SMT_NUM_THREADS_DYNAMIC. For the other architectures, not supporting the partial SMT states, there is no need to define topology_cpu_smt_allowed(), the generic code assumed that all the threads are allowed or only the primary ones. Call the helper from cpu_smt_enable(), and cpu_smt_allowed() when SMT is enabled, to check if the particular thread should be onlined. Notably, also call it from cpu_smt_disable() if CPU_SMT_ENABLED, to allow offlining some threads to move from a higher to lower number of threads online. [ ldufour: Slightly reword the commit's description ] [ ldufour: Introduce CONFIG_SMT_NUM_THREADS_DYNAMIC ] Suggested-by:
-
Laurent Dufour authored
Since the maximum number of threads is now passed to cpu_smt_set_num_threads(), checking that value is enough to know whether SMT is supported. Suggested-by:
-
Michael Ellerman authored
Some architectures allow partial SMT states at boot time, ie. when not all SMT threads are brought online. To support that the SMT code needs to know the maximum number of SMT threads, and also the currently configured number. The architecture code knows the max number of threads, so have the architecture code pass that value to cpu_smt_set_num_threads(). Note that although topology_max_smt_threads() exists, it is not configured early enough to be used here. As architecture, like PowerPC, allows the threads number to be set through the kernel command line, also pass that value. [ ldufour: Slightly reword the commit message ] [ ldufour: Rename cpu_smt_check_topology and add a num_threads argument ] Signed-off-by:
-
Michael Ellerman authored
Move the simple exit cases, i.e. those which don't depend on the value written, earlier in the function. That makes it clearer that regardless of the input those states cannot be transitioned out of. That does have a user-visible effect, in that the error returned will now always be EPERM/ENODEV for those states, regardless of the value written. Previously writing an invalid value would return EINVAL even when in those states. Signed-off-by:
-
Michael Ellerman authored
In order to export the cpuhp_smt_control enum as part of the interface between generic and architecture code, the architecture code needs to include asm/topology.h. But that leads to circular header dependencies. So split the enum and related declarations into a separate header. [ ldufour: Reworded the commit's description ] Signed-off-by:
-
Laurent Dufour authored
The commit 18415f33 ("cpu/hotplug: Allow "parallel" bringup up to CPUHP_BP_KICK_AP_STATE") introduce a dependancy against a global variable cpu_primary_thread_mask exported by the X86 code. This variable is only used when CONFIG_HOTPLUG_PARALLEL is set. Since cpuhp_get_primary_thread_mask() and cpuhp_smt_aware() are only used when CONFIG_HOTPLUG_PARALLEL is set, don't define them when it is not set. No functional change. Signed-off-by:
-
- 23 Jul, 2023 3 commits
-
-
Linus Torvalds authored
-
git://git.kernel.org/pub/scm/linux/kernel/git/trace/linux-traceLinus Torvalds authored
Pull tracing fixes from Steven Rostedt: - Swapping the ring buffer for snapshotting (for things like irqsoff) can crash if the ring buffer is being resized. Disable swapping when this happens. The missed swap will be reported to the tracer - Report error if the histogram fails to be created due to an error in adding a histogram variable, in event_hist_trigger_parse() - Remove unused declaration of tracing_map_set_field_descr() * tag 'trace-v6.5-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/trace/linux-trace: tracing/histograms: Return an error if we fail to add histogram to hist_vars list ring-buffer: Do not swap cpu_buffer during resize process tracing: Remove unused extern declaration tracing_map_set_field_descr()
-
Linus Torvalds authored
Merge tag 'kbuild-fixes-v6.5' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild Pull Kbuild fixes from Masahiro Yamada: - Fix stale help text in gconfig - Support *.S files in compile_commands.json - Flatten KBUILD_CFLAGS - Fix external module builds with Rust so that temporary files are created in the modules directories instead of the kernel tree * tag 'kbuild-fixes-v6.5' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild: kbuild: rust: avoid creating temporary files kbuild: flatten KBUILD_CFLAGS gen_compile_commands: add assembly files to compilation database kconfig: gconfig: correct program name in help text kconfig: gconfig: drop the Show Debug Info help text
-
