This patch add basic structure of a virtual gpio device(gpio-mockup)
for testing gpio subsystem. The tester could manipulate such device
through userspace(sysfs or char device) and check the result from
debugfs.

Currently, it support one or more gpiochip(determined by module
parameters with base,ngpio pair). One could test the overlap of
different gpiochip and test the direction and/or output values of
these chips.
Signed-off-by: Kamlakant Patel <kamlakant.patel@broadcom.com>
Signed-off-by: Bamvor Jian Zhang <bamvor.zhangjian@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

This patch adds zynq specific check for bank 0 pins 7 and 8
are special and cannot be used as inputs
Signed-off-by: Nava kishore Manne <navam@xilinx.com>
Reported-by: Jonas Karlsson <Jonas.d.karlsson@gmail.com>
Acked-by: Sören Brinkmann <soren.brinkmann@xilinx.com>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Implement the get_direction callback for the GPIOs found in the AXP209
PMIC.

Due to the way they are implemented, in the same register you have the
muxing options, GPIO directions and GPIO values. Since you have no control
over what value is there at reset, simply use output as the default.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Remove unneeded error handling on the result of a call
to platform_get_resource() when the value is passed to
devm_ioremap_resource().
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Remove unneeded error handling on the result of a call
to platform_get_resource() when the value is passed to
devm_ioremap_resource().
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

When using GPIO irqchip helpers to setup irqchip for a gpiolib based
driver, it is not possible to select which GPIOs to add to the IRQ domain.
Instead it just adds all GPIOs which is not always desired. For example
there might be GPIOs that for some reason cannot generated normal
interrupts at all.

To support this we add a flag irq_need_valid_mask to struct gpio_chip. When
this flag is set the core allocates irq_valid_mask that holds one bit for
each GPIO the chip has. By default all bits are set but drivers can
manipulate this using set_bit() and clear_bit() accordingly.

Then when gpiochip_irqchip_add() is called, this mask is checked and all
GPIOs with bit is set are added to the IRQ domain created for the GPIO
chip.
Suggested-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

commit d47529b2
"gpio: don't include module.h in shared driver header"
removed <linux/module.h> from the <linux/gpio/driver.h> header.

It seems arch/arm/mach-omap2/board-rx51-peripherals.c
is using __initdata_or_module from <linux/module.h> through
<linux/gpio.h> to <linux/gpio/driver.h>, so break this dependency
so that we get a clean compile.

Cc: Paul Gortmaker <paul.gortmaker@windriver.com>
Cc: Tony Lindgren <tony@atomide.com>
Fixes: d47529b2 ("gpio: don't include module.h in shared driver header")
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

A bunch of variables were just declared "unsigned" and should
be "unsigned int". Fix it up for this driver.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

This adds a .get_direction() callback to the TC3589x and
renames the function for setting single-ended mode to be
more to the point.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

gpiochip_add_data is already used to add data pointer and chip.
Lets rely on gpiochip_get_data which is getting used in other
gpio_chip functions.
Signed-off-by: Amitesh Singh <singh.amitesh@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Use devm_gpiochip_add_data() for GPIO registration and remove the need
of driver callback .remove.
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

In case of error, the function devm_ioremap_resource() returns ERR_PTR()
and never returns NULL. The NULL test in the return value check should
be replaced with IS_ERR().
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Acked-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Most shared headers in include/linux don't need to know what the
internals of a struct module are; all they care about is that it
is a struct and hence they may require a pointer to one.

The advantage in this is that module.h is including a lot of stuff
itself, and an otherwise empty C file that just contains module.h
will result in ~750kB from CPP (compared to say 12kB from init.h)

So we have approximately 50 instances of "struct module;" in the
various include/linux headers already that help us keep module.h
out of other headers; here we do the same for gpio.

Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Alexandre Courbot <gnurou@gmail.com>
Cc: linux-gpio@vger.kernel.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

The Kconfig for this file is:

drivers/gpio/Kconfig:config GPIO_WHISKEY_COVE
drivers/gpio/Kconfig:   tristate "GPIO support for Whiskey Cove PMIC"

...but however it does not include module.h -- it in turn gets it from
another header (gpio/driver.h) and we'd like to replace that with a
forward delcaration of "struct module;" but if we do, this file will
fail to compile.

So we fix this first to avoid putting build failures into the bisect
commit history.

Cc: Ajay Thomas <ajay.thomas.david.rajamanickam@intel.com>
Cc: Bin Gao <bin.gao@intel.com>
Cc: Andy Shevchenko <andy.shevchenko@gmail.com>
Cc: Mika Westerberg <mika.westerberg@linux.intel.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Alexandre Courbot <gnurou@gmail.com>
Cc: linux-gpio@vger.kernel.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

The Kconfig for this file is:

drivers/gpio/Kconfig:config GPIO_LOONGSON1
drivers/gpio/Kconfig:   tristate "Loongson1 GPIO support"

...but however it does not include module.h -- it in turn gets it from
another header (gpio/driver.h) and we'd like to replace that with a
forward delcaration of "struct module;" but if we do, this file will
fail to compile.

So we fix this first to avoid putting build failures into the bisect
commit history.

Cc: Keguang Zhang <keguang.zhang@gmail.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Alexandre Courbot <gnurou@gmail.com>
Cc: linux-mips@linux-mips.org
Cc: linux-gpio@vger.kernel.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

The Kconfig for this file is:

drivers/gpio/Kconfig:config GPIO_ATH79
drivers/gpio/Kconfig: tristate "Atheros AR71XX/AR724X/AR913X GPIO support"

...but however it does not include module.h -- it in turn gets it from
another header (gpio/driver.h) and we'd like to replace that with a
forward delcaration of "struct module;" but if we do, this file will
fail to compile.

So we fix this first to avoid putting build failures into the bisect
commit history.

Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Alexandre Courbot <gnurou@gmail.com>
Cc: linux-gpio@vger.kernel.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

The Kconfig for this file is:

drivers/gpio/Kconfig:config GPIO_ALTERA
drivers/gpio/Kconfig:   tristate "Altera GPIO"

...but however it does not include module.h -- it in turn gets it from
another header (gpio/driver.h) and we'd like to replace that with a
forward delcaration of "struct module;" but if we do, this file will
fail to compile.

So we fix this first to avoid putting build failures into the bisect
commit history.

Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Alexandre Courbot <gnurou@gmail.com>
Cc: linux-gpio@vger.kernel.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

The Kconfig for this file is:

drivers/gpio/Kconfig:config GPIO_TS4800
drivers/gpio/Kconfig: tristate "TS-4800 DIO blocks and compatibles"

...but however it does not include module.h -- it in turn gets it from
another header (gpio/driver.h) and we'd like to replace that with a
forward delcaration of "struct module;" but if we do, this file will
fail to compile.

So we fix this first to avoid putting build failures into the bisect
commit history.

Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Alexandre Courbot <gnurou@gmail.com>
Cc: linux-gpio@vger.kernel.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

This file is currently getting module.h from a global gpio header
and it will faii to build once we remove module.h from that.

However, the driver is controlled with the following Kconfig:

drivers/gpio/Kconfig:config GPIO_SX150X
drivers/gpio/Kconfig:   bool "Semtech SX150x I2C GPIO expander"

and hence the two lines of MODULE_DEVICE_TABLE are no-ops that
can simply be deleted.

Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Alexandre Courbot <gnurou@gmail.com>
Cc: linux-gpio@vger.kernel.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

This file is currently getting module.h from a global gpio header
and it will fail to build once we remove module.h from that.

However, the driver is controlled with the following Kconfig:

drivers/gpio/Kconfig:config GPIO_PALMAS
drivers/gpio/Kconfig:   bool "TI PALMAS series PMICs GPIO"

and hence the line of MODULE_DEVICE_TABLE is a no-op that can simply
be deleted.  In fact it should have been removed in an earlier commit
that did demodularization, however the unseen include prevented my
build testing from detecting it.

Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Alexandre Courbot <gnurou@gmail.com>
Cc: linux-gpio@vger.kernel.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

This reverts commit 313b9a99.

This was already fixed by
commit bf62efeb
"gpio: pca954x: fix undefined error code from remove"

The latter is a better fix since it makes it easier to detect
erronous code by not assigning a default error code.
Reported-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

The build complains about missing MODULE_LICENSE() in
the Aspeed GPIO driver. The license is evident from the
file header, put in "GPL".
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Alistair Popple <alistair@popple.id.au>
Cc: Jeremy Kerr <jk@ozlabs.org>
Cc: Andrew Jeffery <andrew@aj.id.au>
Acked-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Follow DT and forbid default trigger if the GPIO irqchip device is
enumerated from ACPI. Triggering for these devices will be configured
automatically from ACPI interrupt resources provided by the BIOS.
Suggested-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

These structures are only used to copy into other structures, so declare
them as const.

The semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)

// <smpl>
@r disable optional_qualifier@
identifier i;
position p;
@@
static struct gpio_chip i@p = { ... };

@ok@
identifier r.i;
expression e;
position p;
@@
e = i@p;

@bad@
position p != {r.p,ok.p};
identifier r.i;
struct gpio_chip e;
@@
e@i@p

@depends on !bad disable optional_qualifier@
identifier r.i;
@@
static
+const
 struct gpio_chip i = { ... };
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Acked-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Use devm_gpiochip_add_data() for GPIO registration and remove the need
of driver callback .remove.
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Merge tag 'ib-mfd-gpio-regulator-v4.9' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd into devel

Immutable branch between MFD, GPIO and Regulator due for the v4.9 merge window

Linux 4.8-rc2

ret is not initialized so it contains garbage.  Ensure garbage
is not returned in the case that pdata && pdata->teardown is false
by initializing ret to 0.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

This patch switches the driver to use the generic GPIO MMIO functions
that removes a bit of redundant and duplicate code.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Both gpio_export and gpio_free APIs are obsolete now.
Signed-off-by: Amitesh Singh <singh.amitesh@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

pca953x_gpio_set_multiple() has some coding style issues that make it
harder to read. Tweak the code a bit.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

The chip_type variable in struct pca953x_chip is no longer required.

Remove it.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Avoid the unnecessary if-else in pca953x_read_regs() by spltting the
routine into smaller, specialized functions and calling the right one
via a function pointer held in struct pca953x.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Avoid the unnecessary if-else in pca953x_write_regs() by splitting
the routine into smaller, specialized functions and calling the right
one via a function pointer held in struct pca953x_chip.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

There are multiple places in the driver code where a
switch (chip->chip_type) is used to determine the proper register
offset.

Unduplicate the code by adding a simple structure holding the possible
offsets that differ between the pca953x and pca957x chip families and
use it to avoid the checks.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

ARM LPC32xx platform is device-tree only, there is no need to keep
a file with GPIO platform data structures, however some of macro
definitions should be moved to the driver code, which is the only user
of the removed header file.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Using a default trigger is a bad idea if using DT to configure
interrupts, as the device's interrupt specifier will always contain
the trigger configuration.

Let's warn about that particular situation, and revert to not
having a default. Hopefully, the couple of drivers still using
this feature will quickly be fixed.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

R-Car Gen3's GPIO blocks are identical to Gen2's in every respect.

Based on work for the r8a7795 (R-Car H3) by Ulrich Hecht.

Cc: Ulrich Hecht <ulrich.hecht+renesas@gmail.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Tested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

The Orion GPIO controller binding description in mrvl-gpio.txt is obsolete, and
duplicates the description in gpio-mvebu.txt.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>