Skip to content

L
linux
Switch branch/tag
  1. 04 Sep, 2009 13 commits
  3. 03 Sep, 2009 13 commits
    • Eric Dumazet's avatar
      net: Remove debugging code · 55f9d678
      Eric Dumazet authored 
      Remove a debugging aid I accidently left in previous 'cleanup' patch
Signed-off-by: default avatarEric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
      55f9d678
    • Eric Dumazet's avatar
      vlan: enable multiqueue xmits · 2f8bc32b
      Eric Dumazet authored 
      vlan_dev_hard_start_xmit() & vlan_dev_hwaccel_hard_start_xmit()
select txqueue number 0, instead of using index provided by
skb_get_queue_mapping().

This is not correct after commit 2e59af3d
[vlan: multiqueue vlan device] because
txq->tx_packets  & txq->tx_bytes changes are performed on
a single location, and not the right locking.

Fix is to take the appropriate struct netdev_queue pointer
Signed-off-by: default avatarEric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
      2f8bc32b
    • Eric Dumazet's avatar
      net: net/core/dev.c cleanups · d1b19dff
      Eric Dumazet authored 
      Pure style cleanup patch before surgery :)
Signed-off-by: default avatarEric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
      d1b19dff
    • Karl Hiramoto's avatar
      atm/br2684: netif_stop_queue() when atm device busy and netif_wake_queue()... · 137742cf
      Karl Hiramoto authored 
      atm/br2684: netif_stop_queue() when atm device busy and netif_wake_queue() when we can send packets again.

This patch removes the call to dev_kfree_skb() when the atm device is busy.
Calling dev_kfree_skb() causes heavy packet loss then the device is under
heavy load, the more correct behavior should be to stop the upper layers,
then when the lower device can queue packets again wake the upper layers.
Signed-off-by: default avatarKarl Hiramoto <karl@hiramoto.org>
Signed-off-by: default avatarChas Williams <chas@cmf.nrl.navy.mil>
Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
      137742cf
    • Uwe Kleine-König's avatar
      fec: don't enable irqs in hard irq context · 81538e74
      Uwe Kleine-König authored 
      fec_enet_mii, fec_enet_rx and fec_enet_tx are both only called by
fec_enet_interrupt in interrupt context.  So they must not use
spin_lock_irq/spin_unlock_irq.

This fixes:
	WARNING: at kernel/lockdep.c:2140 trace_hardirqs_on_caller+0x130/0x194()
	...
Signed-off-by: default avatarUwe Kleine-König <u.kleine-koenig@pengutronix.de>
Cc: Greg Ungerer <gerg@uclinux.org>
Cc: Ben Hutchings <ben@decadent.org.uk>
Cc: Patrick McHardy <kaber@trash.net>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Matt Waddel <Matt.Waddel@freescale.com>
Cc: netdev@vger.kernel.org
Cc: Tim Sander <tim01@vlsi.informatik.tu-darmstadt.de>
Acked-by: default avatarGreg Ungerer <gerg@uclinux.org>
Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
      81538e74
    • Uwe Kleine-König's avatar
      fec: fix recursive locking of mii_lock · 84177a20
      Uwe Kleine-König authored 
      mii_discover_phy is only called by fec_enet_mii (via mip->mii_func).  So
&fep->mii_lock is already held and mii_discover_phy must not call
mii_queue which locks &fep->mii_lock, too.

This was noticed by lockdep:

	=============================================
	[ INFO: possible recursive locking detected ]
	2.6.31-rc8-00038-g37d0892c #109
	---------------------------------------------
	swapper/1 is trying to acquire lock:
	 (&fep->mii_lock){-.....}, at: [<c01569f8>] mii_queue+0x2c/0xcc

	but task is already holding lock:
	 (&fep->mii_lock){-.....}, at: [<c0156328>] fec_enet_interrupt+0x78/0x460

	other info that might help us debug this:
	2 locks held by swapper/1:
	 #0:  (rtnl_mutex){+.+.+.}, at: [<c0183534>] rtnl_lock+0x18/0x20
	 #1:  (&fep->mii_lock){-.....}, at: [<c0156328>] fec_enet_interrupt+0x78/0x460

	stack backtrace:
	Backtrace:
	[<c00226fc>] (dump_backtrace+0x0/0x108) from [<c01eac14>] (dump_stack+0x18/0x1c)
	 r6:c781d118 r5:c03e41d8 r4:00000001
	[<c01eabfc>] (dump_stack+0x0/0x1c) from [<c005bae4>] (__lock_acquire+0x1a20/0x1a88)
	[<c005a0c4>] (__lock_acquire+0x0/0x1a88) from [<c005bbac>] (lock_acquire+0x60/0x74)
	[<c005bb4c>] (lock_acquire+0x0/0x74) from [<c01edda8>] (_spin_lock_irqsave+0x54/0x68)
	 r7:60000093 r6:c01569f8 r5:c785e468 r4:00000000
	[<c01edd54>] (_spin_lock_irqsave+0x0/0x68) from [<c01569f8>] (mii_queue+0x2c/0xcc)
	 r7:c785e468 r6:c0156b24 r5:600a0000 r4:c785e000
	[<c01569cc>] (mii_queue+0x0/0xcc) from [<c0156b78>] (mii_discover_phy+0x54/0xa8)
	 r8:00000002 r7:00000032 r6:c785e000 r5:c785e360 r4:c785e000
	[<c0156b24>] (mii_discover_phy+0x0/0xa8) from [<c0156354>] (fec_enet_interrupt+0xa4/0x460)
	 r5:c785e360 r4:c077a170
	[<c01562b0>] (fec_enet_interrupt+0x0/0x460) from [<c0066674>] (handle_IRQ_event+0x48/0x120)
	[<c006662c>] (handle_IRQ_event+0x0/0x120) from [<c0068438>] (handle_level_irq+0x94/0x11c)
	...
Signed-off-by: default avatarUwe Kleine-König <u.kleine-koenig@pengutronix.de>
Cc: Greg Ungerer <gerg@uclinux.org>
Cc: Ben Hutchings <ben@decadent.org.uk>
Cc: Patrick McHardy <kaber@trash.net>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Matt Waddel <Matt.Waddel@freescale.com>
Cc: netdev@vger.kernel.org
Cc: Tim Sander <tim01@vlsi.informatik.tu-darmstadt.de>
Acked-by: default avatarGreg Ungerer <gerg@uclinux.org>
Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
      84177a20
    • Ralf Baechle's avatar
      NET: Fix possible corruption in bpqether driver · 3eb00275
      Ralf Baechle authored 
      The bpq ether driver is modifying the data art of the skb by first
dropping the KISS byte (a command byte for the radio) then prepending the
length + 4 of the remaining AX.25 packet to be transmitted as a little
endian 16-bit number.  If the high byte of the length has a different
value than the dropped KISS byte users of clones of the skb may observe
this as corruption.  This was observed with by running listen(8) -a which
uses a packet socket which clones transmit packets.  The corruption will
then typically be displayed for as a KISS "TX Delay" command for AX.25
packets in the range of 252..508 bytes or any other KISS command for
yet larger packets.

Fixed by using skb_cow to create a private copy should the skb be cloned.
Using skb_cow also allows us to cleanup the old logic to ensure sufficient
headroom in the skb.

While at it, replace a return of 0 from bpq_xmit with the proper constant
NETDEV_TX_OK which is now being used everywhere else in this function.

Affected: all 2.2, 2.4 and 2.6 kernels.
Signed-off-by: default avatarRalf Baechle <ralf@linux-mips.org>
Reported-by: default avatarJann Traschewski <jann@gmx.de>
Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
      3eb00275
    • roel kluin's avatar
      WARNING: some request_irq() failures ignored in el2_open() · ab08999d
      roel kluin authored 
      Request_irq() may fail in different ways, handle accordingly.
Signed-off-by: default avatarRoel Kluin <roel.kluin@gmail.com>
Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
      ab08999d
    • Wu Fengguang's avatar
      tcp: replace hard coded GFP_KERNEL with sk_allocation · aa133076
      Wu Fengguang authored 
      This fixed a lockdep warning which appeared when doing stress
memory tests over NFS:

	inconsistent {RECLAIM_FS-ON-W} -> {IN-RECLAIM_FS-W} usage.

	page reclaim => nfs_writepage => tcp_sendmsg => lock sk_lock

	mount_root => nfs_root_data => tcp_close => lock sk_lock =>
			tcp_send_fin => alloc_skb_fclone => page reclaim

David raised a concern that if the allocation fails in tcp_send_fin(), and it's
GFP_ATOMIC, we are going to yield() (which sleeps) and loop endlessly waiting
for the allocation to succeed.

But fact is, the original GFP_KERNEL also sleeps. GFP_ATOMIC+yield() looks
weird, but it is no worse the implicit sleep inside GFP_KERNEL. Both could
loop endlessly under memory pressure.

CC: Arnaldo Carvalho de Melo <acme@ghostprotocols.net>
CC: David S. Miller <davem@davemloft.net>
CC: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: default avatarWu Fengguang <fengguang.wu@intel.com>
Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
      aa133076
    • Ajit Khaparde's avatar
      net/ethtool: Add support for the ethtool feature to flash firmware image from a specified file. · 05c6a8d7
      Ajit Khaparde authored 
      This patch adds support to flash a firmware image to a device using ethtool.
The driver gets the filename of the firmware image and flashes the image
using the request firmware path.

The region "on the chip" to be flashed can be specified by an option.
It is upto the device driver to enumerate the region number passed by ethtool,
to the region to be flashed.

The default behavior is to flash all the regions on the chip.
Signed-off-by: default avatarAjit Khaparde <ajitk@serverengines.com>
Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
      05c6a8d7
    • Eric Dumazet's avatar
      drivers: Kill now superfluous ->last_rx stores · 451f1443
      Eric Dumazet authored 
      The generic packet receive code takes care of setting
netdev->last_rx when necessary, for the sake of the
bonding ARP monitor.
Signed-off-by: default avatarEric Dumazet <eric.dumazet@gmail.com>
Acked-by: default avatarNeil Horman <nhorman@txudriver.com>
Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
      451f1443
    • Eric Dumazet's avatar
      ip: Report qdisc packet drops · 6ce9e7b5
      Eric Dumazet authored 
      Christoph Lameter pointed out that packet drops at qdisc level where not
accounted in SNMP counters. Only if application sets IP_RECVERR, drops
are reported to user (-ENOBUFS errors) and SNMP counters updated.

IP_RECVERR is used to enable extended reliable error message passing,
but these are not needed to update system wide SNMP stats.

This patch changes things a bit to allow SNMP counters to be updated,
regardless of IP_RECVERR being set or not on the socket.

Example after an UDP tx flood
# netstat -s 
...
IP:
    1487048 outgoing packets dropped
...
Udp:
...
    SndbufErrors: 1487048


send() syscalls, do however still return an OK status, to not
break applications.

Note : send() manual page explicitly says for -ENOBUFS error :

 "The output queue for a network interface was full.
  This generally indicates that the interface has stopped sending,
  but may be caused by transient congestion.
  (Normally, this does not occur in Linux. Packets are just silently
  dropped when a device queue overflows.) "

This is not true for IP_RECVERR enabled sockets : a send() syscall
that hit a qdisc drop returns an ENOBUFS error.

Many thanks to Christoph, David, and last but not least, Alexey !
Signed-off-by: default avatarEric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
      6ce9e7b5
    • Eric Dumazet's avatar
      vlan: multiqueue vlan device · 2e59af3d
      Eric Dumazet authored 
      vlan devices are currently not multi-queue capable.

We can do that with a new rtnl_link_ops method,
get_tx_queues(), called from rtnl_create_link()

This new method gets num_tx_queues/real_num_tx_queues
from real device.

register_vlan_device() is also handled.
Signed-off-by: default avatarEric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
      2e59af3d
  5. 02 Sep, 2009 14 commits
GitLab Nexedi Edition | About GitLab | About Nexedi | 沪ICP备2021021310号-2 | 沪ICP备2021021310号-7