Unnecessary platform_set_drvdata() has been removed since the driver
core clears the driver data to NULL after device release or on
probe failure. There is no need to manually clear the device
driver data to NULL.

The Coccinelle semantic patch used to make this change is as follows:
//<smpl>
@@
struct platform_device *pdev;
@@
- platform_set_drvdata(pdev, NULL);
//</smpl>
Signed-off-by: Amitoj Kaur Chawla <amitoj1606@gmail.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Parenthesis alignment issues reported by checkpatch,
fixed here.
Signed-off-by: Diwakar Sharma <sharmalxmail@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

attribute_group are not supposed to change at runtime. All functions
working with attribute_group provided by <linux/sysfs.h> work
with const attribute_group. So mark the non-const structs as const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Merge tag 'iio-for-4.14a' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-next

Jonathan writes:

First round of IIO new device support, features and cleanups for the 4.14 cycle.

4 completely new drivers in this set and plenty of other stuff.

One ABI change due to a silly mistake a long time back. Hopefully no
one will notice.  It effects the numerical order of consumer device
channels which was the reverse of the obvious.  It's going the slow
way to allow us some margin to spot if we have broken userspace or
not (seems unlikely)

New Device Support
* ccs811
  - new driver for the Volatile Organic Compounds (VOC) sensor.
* dln2 adc
  - new driver for the ADC on this flexible usb board.
* EP93xx
  - new driver for this Cirrus logic SoC ADC.
* ltc2471
  - new ADC driver support the ltc2471 and ltc2473
* st_accel
  - add trivial table entries to support H3LIS331DL, LIS331DL, LIS3LV02DL.
* st_gyro
  - add L3GD20H support (again) having fixed the various things that were
    broken in the first try.  Includes devicetree binding.
* stm32 dac
  - add support for the DACs in the STM32F4 series

Features
* Documentation
  - add missing power attribute documentation to the ABI docs.
* at91-sama5d2
  - add hardware trigger and buffered capture support with bindings.
  - suspend and resume functionality.
* bmc150
  - support for the BOSC0200 ACPI device id seen on some tablets.
* hdc100x
  - devicetree bindings
  - document supported devices
  - match table and device ids.
* hts221
  - support active low interrupts (with bindings)
  - open drain mode with bindings.
* htu21
  - OF match table and bindings.
* lsm6dsx
  - open drain mode with bindings
* ltc2497
  - add support for board file based consumer mapping.
* ms5367
  - OF match table and bindings.
* mt7622
  - binding document and OF match table.
  - suspend and resume support.
* rpr0521
  - triggered buffer support.
* tsys01
  - OF match table and bindings.

Cleanups and minor fixes
* core
  - fix ordering of IIO channels to entry numbers when using
    iio_map_array_register rather than reversing them.
  - use the new %pOF format specifier rather than full name for the
    device tree nodes.
* ad7280a
  - fix potential issue with macro argument reuse.
* ad7766
  - drop a pointless NULL value check as it's done in the gpiod code.
* adis16400
  - unsigned -> unsigned int.
* at91 adc
  - make some init data static to reduce code size.
* at91-sama5d2 ADC
  - make some init data static to reduce code size.
* da311
  - make some init data static to reduce code size.
* hid-sensor-rotation
  - drop an unnecessary static.
* hts221
  - refactor the write_with_mask code.
  - move the BDU configuration to probe time as there is no reason for it
    to change.
  - avoid overwriting reserved data during power-down.  This is a fix, but
    the infrastructure need was too invasive to send it to mainline except
    in a merge window.  It's not a regression as it was always wrong.
  - avoid reconfigure the sampling frequency multiple times by just
    doing it in the write_raw function directly.
  - refactor the power_on/off calls into a set_enable.
  - move the dry-enable logic into trig_set_state as that is the only
    place it was used.
* ina219
  - fix polling of ina226 conversion ready flag.
* imx7d
  - add vendor name in kconfig for consistency with similar parts.
* mcp3422
  - Change initial channel to 0 as it feels more logical.
  - Check for some errors in probe.
* meson-saradc
  - add a check of of_match_device return value.
* mpu3050
  - allow open drain for any interrupt type.
* rockchip adc
  - add check on of_match_device return value.
* sca3000
  - drop a trailing whitespace.
* stm32 adc
  - make array stm32h7_adc_ckmodes_spec static.
* stm32 dac
  - fix an error message.
* stm32 timers
  - fix clock name in docs to match reality after changes.
* st_accel
  - explicit OF table (spi).
  - add missing entries to OF table (i2c).
  - rename of_device_id table to drop the part name.
  - adding missing lis3l02dq entry to bindings.
  - rename H3LIS331DL_DRIVER_NAME to line up with similar entries in driver.
* st_gyro
  - explicit OF table (spi).
* st_magn
  - explicit OF table (spi).
  - enable multiread for lis3mdl.
* st_pressure
  - explicit OF table (spi).
* st_sensors common.
  - move st_sensors_of_i2c_probe and rename to make it available for spi
  drivers.
* tsc3472
  - don't write an extra byte when writing the ATIME register.
  - add a link to the datasheet.
* tsl2x7x - continued staging cleanups
  - add of_match_table.
  - drop redundant power_state sysfs attribute.
  - drop wrapper tsl2x7x_i2c_read.
  - clean up i2c calls made in tsl2x7x_als_calibrate.
  - refactor the read and write _event_value callbacks to handle additional
    elements.
  - use usleep_range instead of mdelay.
  - check return value from tsl2x7x_invoke_change.
* zpa2326
  - add some newline to the end of logging macros.

Move data-ready configuration in hts221_buffer.c since it is only related
to trigger logic
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@st.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@st.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

Add open drain support in order to share requested IRQ line between
hts221 device and other peripherals
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@st.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

New driver adding support for ADC found on Cirrus Logic EP93xx series of SoCs.
Board specific code must take care to create plaform device with all necessary
resources.
Signed-off-by: Alexander Sverdlin <alexander.sverdlin@gmail.com>
Acked-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

This resolves a merge issue and gets the vmbox drm driver into this
branch to be able to start taking fixes for it...
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This adds a perl script to actually parse the MAINTAINERS file, clean up
some whitespace in it, warn about errors in it, and then properly sort
the end result.

My perl-fu is atrocious, so the script has basically been created by
randomly putting various characters in a pile, mixing them around, and
then looking it the end result does anything interesting when used as a
perl script.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Prepping for scripting the MAINTAINERS file cleanup (and possible split)
showed a couple of cases where the headers for a couple of entries were
bogus.

There's a few different kinds of bogosities:

 - the X-GENE SOC EDAC case was confused and split over two lines

 - there were four entries for "GREYBUS PROTOCOLS DRIVERS" that were all
   different things.

 - the NOKIA N900 CAMERA SUPPORT" was duplicated

all of which were more obvious when you started doing associative arrays
in perl to track these things by the header (so that we can alphabetize
this thing properly, and so that we might split it up by the data too).

Cc: Joe Perches <joe@perches.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Pull xen fixes from Juergen Gross:
 "Some fixes and cleanups for running under Xen"

* tag 'for-linus-4.13b-rc2-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
  xen/balloon: don't online new memory initially
  xen/x86: fix cpu hotplug
  xen/grant-table: log the lack of grants
  xen/x86: Don't BUG on CPU0 offlining

When setting up the Xenstore watch for the memory target size the new
watch will fire at once. Don't try to reach the configured target size
by onlining new memory in this case, as the current memory size will
be smaller in almost all cases due to e.g. BIOS reserved pages.

Onlining new memory will lead to more problems e.g. undesired conflicts
with NVMe devices meant to be operated as block devices.

Instead remember the difference between target size and current size
when the watch fires for the first time and apply it to any further
size changes, too.

In order to avoid races between balloon.c and xen-balloon.c init calls
do the xen-balloon.c initialization from balloon.c.
Signed-off-by: Juergen Gross <jgross@suse.com>
Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Signed-off-by: Juergen Gross <jgross@suse.com>

Commit dc6416f1 ("xen/x86: Call
cpu_startup_entry(CPUHP_AP_ONLINE_IDLE) from xen_play_dead()")
introduced an error leading to a stack overflow of the idle task when
a cpu was brought offline/online many times: by calling
cpu_startup_entry() instead of returning at the end of xen_play_dead()
do_idle() would be entered again and again.

Don't use cpu_startup_entry(), but cpuhp_online_idle() instead allowing
to return from xen_play_dead().

Cc: <stable@vger.kernel.org> # 4.12
Signed-off-by: Juergen Gross <jgross@suse.com>
Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Signed-off-by: Juergen Gross <jgross@suse.com>

log a message when we enter this situation:
1) we already allocated the max number of available grants from hypervisor
and
2) we still need more (but the request fails because of 1)).

Sometimes the lack of grants causes IO hangs in xen_blkfront devices.
Adding this log would help debuging.
Signed-off-by: Wengang Wang <wen.gang.wang@oracle.com>
Reviewed-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Reviewed-by: Junxiao Bi <junxiao.bi@oracle.com>
Reviewed-by: Juergen Gross <jgross@suse.com>
Signed-off-by: Juergen Gross <jgross@suse.com>

CONFIG_BOOTPARAM_HOTPLUG_CPU0 allows to offline CPU0 but Xen HVM guests
BUG() in xen_teardown_timer(). Remove the BUG_ON(), this is probably a
leftover from ancient times when CPU0 hotplug was impossible, it works
just fine for HVM.
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Acked-by: Juergen Gross <jgross@suse.com>
Signed-off-by: Juergen Gross <jgross@suse.com>

Now that we have a custom printf format specifier, convert users of
full_name to use %pOF instead. This is preparation to remove storing
of the full path string for each node.
Signed-off-by: Rob Herring <robh@kernel.org>
Cc: Jonathan Cameron <jic23@kernel.org>
Cc: Hartmut Knaack <knaack.h@gmx.de>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: Peter Meerwald-Stadler <pmeerw@pmeerw.net>
Cc: Carlo Caione <carlo@caione.org>
Cc: Kevin Hilman <khilman@baylibre.com>
Cc: linux-iio@vger.kernel.org
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-amlogic@lists.infradead.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

CHECK: Macro argument reuse 'addr' - possible side-effects?

convert AD7280A_DEVADDR to ad7280a_devaddr static function
to fix checkpath check

v3: small style changes
Signed-off-by: Jaya Durga <rjdurga@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

Update hts221 device binding with active-low interrupts support
(IRQ_TYPE_LEVEL_LOW and IRQ_TYPE_EDGE_FALLING).
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@st.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

Add support for active low interrupts (IRQF_TRIGGER_LOW and
IRQF_TRIGGER_FALLING). Configure the device as active high or low
according to the requested irq line.
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@st.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@st.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

Configure sensor ODR just in hts221_write_raw() in order to avoid
to set device sample rate multiple times.
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@st.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

GENMASK(6, 3) in CTRL_REG1 and GENMASK(6, 2) in CTRL_REG2 are marked
reserved. Do not changed the original value (not declared in the
datasheet) during power-down/suspend routines.

Fixes: e4a70e3e (iio: humidity: add support to hts221 rh/temp device)
Fixes: b7079eea (iio: humidity: hts221: add power management support)
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@st.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

Enable Block Data Update in hts221_probe() in order to avoid to reconfigure
it every time the sensor is enabled
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@st.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

Move bit-shift in hts221_write_with_mask() instead of coding
the shift depth in the configured value. That change will be necessary
to fix an issue in device power-down procedure.
Simplify hts221_avg_list table management
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@st.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

Add support for CCS811 VOC sensor. This patch adds support
for reading current and voltage across the sensor and TVOC
and equivalent CO2 values.

Scale and offset values have been computed according to datasheet:
    - For current: raw value is in microamps
        => 0.001 scale to convert to milliamps
    - For voltage: 1.65V = 1023, therefore 1650mV = 1023
        => 1650.0/1023 = 1.612903 scale to convert to millivolts
    - For eCO2: raw value range is from 400ppm to 8192ppm.
        => (val - 400) * (100 - 0) / (8192 - 400) + 0 =
           (val - 400) * 0.01283367 => offset: -400, scale = 0.012834
           to get a percentage value
    -For TVOC: raw value range is from 0ppb to 1187ppb.
        => (val - 0) * 100 / (1187 - 0) + 0 = val * 0.0842459 =>
            scale = 0.084246 for getting a percentage value

Cc: Daniel Baluta <daniel.baluta@gmail.com>
Cc: Alison Schofield <amsfield22@gmail.com>
Signed-off-by: Narcisa Ana Maria Vasile <narcisaanamaria12@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

Merge tag 'hwmon-for-linus-v4.13-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging

Pull hwmon fix from Guenter Roeck:
 "Avoid buffer overruns in applesmc driver"

* tag 'hwmon-for-linus-v4.13-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging:
  hwmon: (applesmc) Avoid buffer overruns

Pull tty/serial fixes from Greg KH:
 "Here are some small tty and serial driver fixes for 4.13-rc2. Nothing
  huge at all, a revert of a patch that turned out to break things, a
  fix up for a new tty ioctl we added in 4.13-rc1 to get the uapi
  definition correct, and a few minor serial driver fixes for reported
  issues.

  All of these have been in linux-next for a while with no reported
  issues"

* tag 'tty-4.13-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
  tty: Fix TIOCGPTPEER ioctl definition
  tty: hide unused pty_get_peer function
  tty: serial: lpuart: Fix the logic for detecting the 32-bit type UART
  serial: imx: Prevent TX buffer PIO write when a DMA has been started
  Revert "serial: imx-serial - move DMA buffer configuration to DT"
  serial: sh-sci: Uninitialized variables in sysfs files
  serial: st-asc: Potential error pointer dereference

Pull char/misc driver fixes from Greg KH:
 "Here are some small char and misc driver fixes for 4.13-rc2. All fix
  reported problems with 4.13-rc1 or older kernels (like the binder
  fixes). Full details in the shortlog.

  All have been in linux-next with no reported issues"

* tag 'char-misc-4.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
  w1: omap-hdq: fix error return code in omap_hdq_probe()
  regmap: regmap-w1: Fix build troubles
  w1: Fix slave count on 1-Wire bus (resend)
  mux: mux-core: unregister mux_class in mux_exit()
  mux: remove the Kconfig question for the subsystem
  nvmem: rockchip-efuse: amend compatible rk322x-efuse to rk3228-efuse
  drivers/fsi: fix fsi_slave_mode prototype
  fsi: core: register with postcore_initcall
  thunderbolt: Correct access permissions for active NVM contents
  vmbus: re-enable channel tasklet
  spmi: pmic-arb: Always allocate ppid_to_apid table
  MAINTAINERS: Add entry for SPMI subsystem
  spmi: Include OF based modalias in device uevent
  binder: Use wake up hint for synchronous transactions.
  binder: use group leader instead of open thread
  Revert "android: binder: Sanity check at binder ioctl"

Pull USB fixes from Greg KH:
 "Here are some small USB fixes for 4.13-rc2.

  The usual batch, gadget fixes for reported issues, as well as xhci
  fixes, and a small random collection of other fixes for reported
  issues.

  All have been in linux-next with no reported issues"

* tag 'usb-4.13-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (25 commits)
  xhci: fix memleak in xhci_run()
  usb: xhci: fix spinlock recursion for USB2 test mode
  xhci: fix 20000ms port resume timeout
  usb: xhci: Issue stop EP command only when the EP state is running
  xhci: Bad Ethernet performance plugged in ASM1042A host
  xhci: Fix NULL pointer dereference when cleaning up streams for removed host
  usb: renesas_usbhs: gadget: disable all eps when the driver stops
  usb: renesas_usbhs: fix usbhsc_resume() for !USBHSF_RUNTIME_PWCTRL
  usb: gadget: udc: renesas_usb3: protect usb3_ep->started in usb3_start_pipen()
  usb: gadget: udc: renesas_usb3: fix zlp transfer by the dmac
  usb: gadget: udc: renesas_usb3: fix free size in renesas_usb3_dma_free_prd()
  usb: gadget: f_uac2: endianness fixes.
  usb: gadget: f_uac1: endianness fixes.
  include: usb: audio: specify exact endiannes of descriptors
  usb: gadget: udc: start_udc() can be static
  usb: dwc2: gadget: On USB RESET reset device address to zero
  usb: storage: return on error to avoid a null pointer dereference
  usb: typec: include linux/device.h in ucsi.h
  USB: cdc-acm: add device-id for quirky printer
  usb: dwc3: gadget: only unmap requests from DMA if mapped
  ...

Pull staging driver fixes from Greg KH:
 "Here are some small staging driver fixes for reported issues for
  4.13-rc2.

  Also in here is a new driver, the virtualbox DRM driver. It's
  stand-alone and got acks from the DRM developers to go in through this
  tree. It's a new thing, but it should be fine for this point in the rc
  cycle due to it being independent.

  All of this has been in linux-next for a while with no reported
  issues"

* tag 'staging-4.13-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
  staging: rtl8188eu: add TL-WN722N v2 support
  staging: speakup: safely register and unregister ldisc
  staging: speakup: add functions to register and unregister ldisc
  staging: speakup: safely close tty
  staging: sm750fb: avoid conflicting vesafb
  staging: lustre: ko2iblnd: check copy_from_iter/copy_to_iter return code
  staging: vboxvideo: Add vboxvideo to drivers/staging
  staging: sm750fb: fixed a assignment typo
  staging: rtl8188eu: memory leak in rtw_free_cmd_obj()
  staging: vchiq_arm: fix error codes in probe
  staging: comedi: ni_mio_common: fix AO timer off-by-one regression

Fix major alphabetic errors.  No attempt to fix items that all begin
with the same word (like ARM, BROADCOM, DRM, EDAC, FREESCALE, INTEL,
OMAP, PCI, SAMSUNG, TI, USB, etc.).

(diffstat +/- is different by one line because TI KEYSTONE MULTICORE
had 2 blank lines after it.)
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Acked-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Pull NFS client bugfixes from Anna Schumaker:
 "Stable bugfix:
   - Fix error reporting regression

  Bugfixes:
   - Fix setting filelayout ds address race
   - Fix subtle access bug when using ACLs
   - Fix setting mnt3_counts array size
   - Fix a couple of pNFS commit races"

* tag 'nfs-for-4.13-2' of git://git.linux-nfs.org/projects/anna/linux-nfs:
  NFS/filelayout: Fix racy setting of fl->dsaddr in filelayout_check_deviceid()
  NFS: Be more careful about mapping file permissions
  NFS: Store the raw NFS access mask in the inode's access cache
  NFSv3: Convert nfs3_proc_access() to use nfs_access_set_mask()
  NFS: Refactor NFS access to kernel access mask calculation
  net/sunrpc/xprt_sock: fix regression in connection error reporting.
  nfs: count correct array for mnt3_counts array size
  Revert commit 722f0b89 ("pNFS: Don't send COMMITs to the DSes if...")
  pNFS/flexfiles: Handle expired layout segments in ff_layout_initiate_commit()
  NFS: Fix another COMMIT race in pNFS
  NFS: Fix a COMMIT race in pNFS
  mount: copy the port field into the cloned nfs_server structure.
  NFS: Don't run wake_up_bit() when nobody is waiting...
  nfs: add export operations

Pull overlayfs fixes from Miklos Szeredi:
 "This fixes a crash with SELinux and several other old and new bugs"

* 'overlayfs-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mszeredi/vfs:
  ovl: check for bad and whiteout index on lookup
  ovl: do not cleanup directory and whiteout index entries
  ovl: fix xattr get and set with selinux
  ovl: remove unneeded check for IS_ERR()
  ovl: fix origin verification of index dir
  ovl: mark parent impure on ovl_link()
  ovl: fix random return value on mount

Pull block fixes from Jens Axboe:
 "A small set of fixes for -rc2 - two fixes for BFQ, documentation and
  code, and a removal of an unused variable in nbd. Outside of that, a
  small collection of fixes from the usual crew on the nvme side"

* 'for-linus' of git://git.kernel.dk/linux-block:
  nvmet: don't report 0-bytes in serial number
  nvmet: preserve controller serial number between reboots
  nvmet: Move serial number from controller to subsystem
  nvmet: prefix version configfs file with attr
  nvme-pci: Fix an error handling path in 'nvme_probe()'
  nvme-pci: Remove nvme_setup_prps BUG_ON
  nvme-pci: add another device ID with stripe quirk
  nvmet-fc: fix byte swapping in nvmet_fc_ls_create_association
  nvme: fix byte swapping in the streams code
  nbd: kill unused ret in recv_work
  bfq: dispatch request to prevent queue stalling after the request completion
  bfq: fix typos in comments about B-WF2Q+ algorithm

Pull more rdma fixes from Doug Ledford:
 "As per my previous pull request, there were two drivers that each had
  a rather large number of legitimate fixes still to be sent.

  As it turned out, I also missed a reasonably large set of fixes from
  one person across the stack that are all important fixes. All in all,
  the bnxt_re, i40iw, and Dan Carpenter are 3/4 to 2/3rds of this pull
  request.

  There were some other random fixes that I didn't send in the last pull
  request that I added to this one. This catches the rdma stack up to
  the fixes from up to about the beginning of this week. Any more fixes
  I'll wait and batch up later in the -rc cycle. This will give us a
  good base to start with for basing a for-next branch on -rc2.

  Summary:

   - i40iw fixes

   - bnxt_re fixes

   - Dan Carpenter bugfixes across stack

   - ten more random fixes, no more than two from any one person"

* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dledford/rdma: (37 commits)
  RDMA/core: Initialize port_num in qp_attr
  RDMA/uverbs: Fix the check for port number
  IB/cma: Fix reference count leak when no ipv4 addresses are set
  RDMA/iser: don't send an rkey if all data is written as immadiate-data
  rxe: fix broken receive queue draining
  RDMA/qedr: Prevent memory overrun in verbs' user responses
  iw_cxgb4: don't use WR keys/addrs for 0 byte reads
  IB/mlx4: Fix CM REQ retries in paravirt mode
  IB/rdmavt: Setting of QP timeout can overflow jiffies computation
  IB/core: Fix sparse warnings
  RDMA/bnxt_re: Fix the value reported for local ack delay
  RDMA/bnxt_re: Report MISSED_EVENTS in req_notify_cq
  RDMA/bnxt_re: Fix return value of poll routine
  RDMA/bnxt_re: Enable atomics only if host bios supports
  RDMA/bnxt_re: Specify RDMA component when allocating stats context
  RDMA/bnxt_re: Fixed the max_rd_atomic support for initiator and destination QP
  RDMA/bnxt_re: Report supported value to IB stack in query_device
  RDMA/bnxt_re: Do not free the ctx_tbl entry if delete GID fails
  RDMA/bnxt_re: Fix WQE Size posted to HW to prevent it from throwing error
  RDMA/bnxt_re: Free doorbell page index (DPI) during dealloc ucontext
  ...

Pull drm fixes from Dave Airlie:
 "A bunch of fixes for rc2: two imx regressions, vc4 fix, dma-buf fix,
  some displayport mst fixes, and an amdkfd fix.

  Nothing too crazy, I assume we just haven't see much rc1 testing yet"

* tag 'drm-fixes-for-v4.13-rc2' of git://people.freedesktop.org/~airlied/linux:
  drm/mst: Avoid processing partially received up/down message transactions
  drm/mst: Avoid dereferencing a NULL mstb in drm_dp_mst_handle_up_req()
  drm/mst: Fix error handling during MST sideband message reception
  drm/imx: parallel-display: Accept drm_of_find_panel_or_bridge failure
  drm/imx: fix typo in ipu_plane_formats[]
  drm/vc4: Fix VBLANK handling in crtc->enable() path
  dma-buf/fence: Avoid use of uninitialised timestamp
  drm/amdgpu: Remove unused field kgd2kfd_shared_resources.num_mec
  drm/radeon: Remove initialization of shared_resources.num_mec
  drm/amdkfd: Remove unused references to shared_resources.num_mec
  drm/amdgpu: Fix KFD oversubscription by tracking queues correctly

Pull tracing fixes from Steven Rostedt:
 "Three minor updates

   - Use the new GFP_RETRY_MAYFAIL to be more aggressive in allocating
     memory for the ring buffer without causing OOMs

   - Fix a memory leak in adding and removing instances

   - Add __rcu annotation to be able to debug RCU usage of function
     tracing a bit better"

* tag 'trace-v4.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
  trace: fix the errors caused by incompatible type of RCU variables
  tracing: Fix kmemleak in instance_rmdir
  tracing/ring_buffer: Try harder to allocate

Pull KVM fixes from Radim Krčmář:
 "A bunch of small fixes for x86"

* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
  kvm: x86: hyperv: avoid livelock in oneshot SynIC timers
  KVM: VMX: Fix invalid guest state detection after task-switch emulation
  x86: add MULTIUSER dependency for KVM
  KVM: nVMX: Disallow VM-entry in MOV-SS shadow
  KVM: nVMX: track NMI blocking state separately for each VMCS
  KVM: x86: masking out upper bits