- 06 Feb, 2024 3 commits
-
-
Minh Le authored
Add a device node for the RCLK Watchdog Timer (RWDT) on the Renesas R-Car V4M (R8A779H0) SoC. Signed-off-by:
Minh Le <minh.le.aj@renesas.com> Signed-off-by:
Geert Uytterhoeven <geert+renesas@glider.be> Reviewed-by:
Wolfram Sang <wsa+renesas@sang-engineering.com> Link: https://lore.kernel.org/r/43bb03f3baa87b4be8ce953b1955df6b89387e4c.1706790320.git.geert+renesas@glider.be
-
Geert Uytterhoeven authored
Add the input capture interrupt on Timer Unit instances that have it. Add "interrupt-names" properties for clarity. Signed-off-by:
-
Geert Uytterhoeven authored
Add the input capture interrupt on Timer Unit instances that have it. Add "interrupt-names" properties for clarity. Signed-off-by:
-
- 31 Jan, 2024 9 commits
-
-
Biju Das authored
Add CSI and CRU nodes r9a07g043 (RZ/G2UL) SoC DTSI. Signed-off-by:
Biju Das <biju.das.jz@bp.renesas.com> Reviewed-by:
-
Geert Uytterhoeven authored
Add initial support for the Renesas Gray Hawk Single board, which is based on the R-Car V4M (R8A779H0) SoC: - Memory, - Crystal oscillators, - Serial console. Based on the White Hawk Single DTS, and on a patch for the Gray Hawk board stack in the BSP by Hai Pham. Signed-off-by:
Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se> Link: https://lore.kernel.org/r/b657402113267acd57aece0b4c681b707e704455.1706194617.git.geert+renesas@glider.be
-
Hai Pham authored
Add initial support for the Renesas R-Car V4M (R8A779H0) SoC. Signed-off-by:
Hai Pham <hai.pham.ud@renesas.com> Signed-off-by:
-
Geert Uytterhoeven authored
Renesas R-Car V4M DT Binding Definitions Clock and Power Domain definitions for the Renesas R-Car V4M (R8A779H0) SoC, shared by driver and DT source files.
-
Claudiu Beznea authored
Enable the watchdog interface (accessible by Cortex-A of RZ/G3S SoC) on RZ/G3S SMARC SoM. Signed-off-by:
Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com> Reviewed-by:
-
Claudiu Beznea authored
Add the DT node for the watchdog IP accessible by Cortex-A of RZ/G3S SoC (R9108G045). Signed-off-by:
-
Geert Uytterhoeven authored
R-Car V4H actually has two SCIF_CLK pins. The second pin provides the SCIF_CLK signal for HSCIF2 and SCIF4. Fixes: a4c31c56 ("arm64: dts: renesas: r8a779g0: Add SCIF nodes") Fixes: 39d9dfc6 ("arm64: dts: renesas: r8a779g0: Add remaining HSCIF nodes") Signed-off-by:
-
Duy Nguyen authored
Add all Clock Pulse Generator Core Clock Outputs for the Renesas R-Car V4M (R8A779H0) SoC. Signed-off-by:
Duy Nguyen <duy.nguyen.rh@renesas.com> Signed-off-by:
Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> Link: https://lore.kernel.org/r/11acbd2a30b58607474e9c32eb798b3a00e85e73.1706194617.git.geert+renesas@glider.be
-
Geert Uytterhoeven authored
Document support for the Clock Pulse Generator (CPG) and Module Standby Software Reset (MSSR) module on the Renesas R-Car V4M (R8A779H0) SoC. Signed-off-by:
Conor Dooley <conor.dooley@microchip.com> Reviewed-by:
-
- 30 Jan, 2024 2 commits
-
-
Duy Nguyen authored
Add power domain indices for the Renesas R-Car V4M (R8A779H0) SoC. Signed-off-by:
Ulf Hansson <ulf.hansson@linaro.org>
-
Duy Nguyen authored
Document support for the System Controller (SYSC) in the R-Car V4M (R8A779H0) SoC. Signed-off-by:
-
- 29 Jan, 2024 10 commits
-
-
Geert Uytterhoeven authored
The White Hawk Single board is a single-board integration of the Renesas White Hawk CPU and Breakout board stack, based on the R-Car V4H ES2.0 (R8A779G2) SoC. For now, the only visible differences compared to the board stack are: - The SoC is an updated version of R-Car V4H (R8A779G0), - The serial console uses an FT2232H instead of a CP2102 USB-UART bridge, with CTS/RTS wired. Signed-off-by: -
Geert Uytterhoeven authored
Add support for the Renesas R-Car V4H ES2.0 (R8A779G2) SoC, which is an updated version of the R-Car V4H (R8A779G0) SoC. Signed-off-by:
-
Geert Uytterhoeven authored
Factor out the parts on the White Hawk BreakOut board that are also present on the White Hawk Single board, so they can be reused when introducing support for the latter. Signed-off-by:
-
Geert Uytterhoeven authored
Factor out the parts on the White Hawk CPU board that are also present on the White Hawk Single board, so they can be reused when introducing support for the latter. Signed-off-by:
-
Geert Uytterhoeven authored
The White Hawk CPU and BreakOut board DTS is specific to R-Car V4H. Document it in the top-level comment. Signed-off-by:
-
Geert Uytterhoeven authored
The White Hawk CSI/DSI and RAVB/Ethernet(1000Base-T1) sub boards are not specific to R-Car V4H. Hence rename their DTS file names to drop the "r8a779g0-" prefix, and remove any references to R-Car V4H. Signed-off-by:
-
Geert Uytterhoeven authored
Alphabetical by node name. Signed-off-by:
-
Geert Uytterhoeven authored
The White Hawk CPU board can be used standalone, without connecting it to the White Hawk BreakOut board. Add a DTS file for supporting this use case. Signed-off-by:
-
Wolfram Sang authored
Signed-off-by:
-
Wolfram Sang authored
Schematics say that all these 3.3v sources are driven by "D3.3V". We have a regulator for it already in ulcb.dtsi. Use it instead. Signed-off-by:
-
- 22 Jan, 2024 5 commits
-
-
Geert Uytterhoeven authored
Numerical by unit address, alphabetical by node name. Signed-off-by:
-
Geert Uytterhoeven authored
According to Table 8.1, "Summary of Module Power, Reset condition and Clock assignment" of the R-Mobile APE6 Hardware Manual Rev. 0.7, the parent clock of the thermal sensor clock is the Common Peripheral (CP) clock, which runs at 13 MHz (main clock / 2). As the R-Car Thermal driver does not use the clock rate, this change has no functional impact. Signed-off-by:
-
Geert Uytterhoeven authored
Add the Common Peripheral (CP) clock, which is driven by the main clock / 2 during normal system operation, but may be driven by EXTALR during early system boot, when SYSCLK_EN is still low. As the latter is irrelevant to Linux, just model it as a fixed clock driven from main_div2_clk. Switch all users of main_div2_clk that are documented to be clocked by the CP clock to cp_clk, to better reflect the actual clock topology. Signed-off-by:
-
Geert Uytterhoeven authored
External clocks should be defined as zero-Hz clocks in the SoC .dtsi, and overridden in the board .dts when present. Correct the clock rate of extal1 from 25 to 26 MHz, to match the crystal oscillator present on the APE6-EVM board. Fixes: a76809a3 ("ARM: shmobile: r8a73a4: Common clock framework DT description") Signed-off-by:
-
Claudiu Beznea authored
RZ SMARC Carrier II board has 3 user buttons called USER_SW1, USER_SW2, USER_SW3. Add a DT node in device tree to propertly instantiate the gpio-keys driver for these buttons. Signed-off-by:
-
- 21 Jan, 2024 11 commits
-
-
Linus Torvalds authored
-
https://evilpiepirate.org/git/bcachefsLinus Torvalds authored
Pull more bcachefs updates from Kent Overstreet: "Some fixes, Some refactoring, some minor features: - Assorted prep work for disk space accounting rewrite - BTREE_TRIGGER_ATOMIC: after combining our trigger callbacks, this makes our trigger context more explicit - A few fixes to avoid excessive transaction restarts on multithreaded workloads: fstests (in addition to ktest tests) are now checking slowpath counters, and that's shaking out a few bugs - Assorted tracepoint improvements - Starting to break up bcachefs_format.h and move on disk types so they're with the code they belong to; this will make room to start documenting the on disk format better. - A few minor fixes" * tag 'bcachefs-2024-01-21' of https://evilpiepirate.org/git/bcachefs: (46 commits) bcachefs: Improve inode_to_text() bcachefs: logged_ops_format.h bcachefs: reflink_format.h bcachefs; extents_format.h bcachefs: ec_format.h bcachefs: subvolume_format.h bcachefs: snapshot_format.h bcachefs: alloc_background_format.h bcachefs: xattr_format.h bcachefs: dirent_format.h bcachefs: inode_format.h bcachefs; quota_format.h bcachefs: sb-counters_format.h bcachefs: counters.c -> sb-counters.c bcachefs: comment bch_subvolume bcachefs: bch_snapshot::btime bcachefs: add missing __GFP_NOWARN bcachefs: opts->compression can now also be applied in the background bcachefs: Prep work for variable size btree node buffers bcachefs: grab s_umount only if snapshotting ... -
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tipLinus Torvalds authored
Pull timer updates from Thomas Gleixner: "Updates for time and clocksources: - A fix for the idle and iowait time accounting vs CPU hotplug. The time is reset on CPU hotplug which makes the accumulated systemwide time jump backwards. - Assorted fixes and improvements for clocksource/event drivers" * tag 'timers-core-2024-01-21' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: tick-sched: Fix idle and iowait sleeptime accounting vs CPU hotplug clocksource/drivers/ep93xx: Fix error handling during probe clocksource/drivers/cadence-ttc: Fix some kernel-doc warnings clocksource/drivers/timer-ti-dm: Fix make W=n kerneldoc warnings clocksource/timer-riscv: Add riscv_clock_shutdown callback dt-bindings: timer: Add StarFive JH8100 clint dt-bindings: timer: thead,c900-aclint-mtimer: separate mtime and mtimecmp regs -
git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linuxLinus Torvalds authored
Pull powerpc fixes from Aneesh Kumar: - Increase default stack size to 32KB for Book3S Thanks to Michael Ellerman. * tag 'powerpc-6.8-2' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux: powerpc/64s: Increase default stack size to 32KB
-
Kent Overstreet authored
Add line breaks - inode_to_text() is now much easier to read. Signed-off-by:Kent Overstreet <kent.overstreet@linux.dev>
-
Kent Overstreet authored
Signed-off-by: -
Kent Overstreet authored
Signed-off-by: -
Kent Overstreet authored
Signed-off-by: -
Kent Overstreet authored
Signed-off-by: -
Kent Overstreet authored
Signed-off-by: -
Kent Overstreet authored
Signed-off-by:
-
