RTL8821CS is a WiFi + Bluetooth combo chip from Realtek that provides
WiFi A/B/G/N/AC over an SDIO interface and Bluetooth 4.2 over a UART
interface.

Note that the firmware this was tested with was firmware version
0x75b8f098.
Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

Add compatible string for RTL8821CS for existing Realtek Bluetooth
driver.
Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Alistair Francis <alistair@alistair23.me>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

This bluetooth device is found in a combo WLAN/BT card
for a MediaTek 7663.

Tested on Acer Aspire A315-24P Notebook

The device information:

T:  Bus=01 Lev=01 Prnt=01 Port=01 Cnt=01 Dev#=  2 Spd=480  MxCh= 0
D:  Ver= 2.10 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs=  1
P:  Vendor=04ca ProdID=3801 Rev= 1.00
S:  Manufacturer=MediaTek Inc.
S:  Product=Wireless_Device
S:  SerialNumber=000000000
C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA
A:  FirstIf#= 0 IfCount= 2 Cls=e0(wlcon) Sub=01 Prot=01
I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=81(I) Atr=03(Int.) MxPS=  16 Ivl=125us
E:  Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=   0 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=   0 Ivl=1ms
I:  If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=   9 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=   9 Ivl=1ms
I:  If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  17 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  17 Ivl=1ms
I:  If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  25 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  25 Ivl=1ms
I:  If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  33 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  33 Ivl=1ms
I:  If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  49 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  49 Ivl=1ms
I:  If#= 1 Alt= 6 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  63 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  63 Ivl=1ms
Signed-off-by: Meng Tang <tangmeng@uniontech.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

This fixes the following new warning:

net/bluetooth/hci_sync.c:2403 hci_pause_addr_resolution() warn: missing
error code? 'err'
Reported-by: kernel test robot <lkp@intel.com>
Reported-by: Dan Carpenter <error27@gmail.com>
Link: https://lore.kernel.org/r/202302251952.xryXOegd-lkp@intel.com/Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

This makes hci_conn_hash_add append to the tail of the conn_hash so it
matches the order they are created, this is required if the controller
attempts to match the order of ACL with CIS which uses append logic
when programming the CIS ids on the CIG.

The result of this change affects Create CIS:

Before:

< HCI Command: LE Create Connected Isochronous Stream (0x08|0x0064) plen 9
        Number of CIS: 2
        CIS Handle: 2560
        ACL Handle: 3586
        CIS Handle: 2561
        ACL Handle: 3585

After:

< HCI Command: LE Create Connected Isochronous Stream (0x08|0x0064) plen 9
        Number of CIS: 2
        CIS Handle: 2560
        ACL Handle: 3585
        CIS Handle: 2561
        ACL Handle: 3586
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

Add the support for RTL8852BS BT controller on UART interface.
The necessary firmware file will be submitted to linux-firmware.
Signed-off-by: Victor Hassan <victor@allwinnertech.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

Add serdev support for the 88W8997 from NXP (previously Marvell). It
includes support for changing the baud rate. The command to change the
baud rate is taken from the user manual UM11483 Rev. 9 in section 7
(Bring-up of Bluetooth interfaces) from NXP.
Signed-off-by: Stefan Eichenberger <stefan.eichenberger@toradex.com>
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

Use the maybe_unused macro for the device tree ids instead of #ifdef
CONFIG_OF. This makes it easier to add support for new devices.
Signed-off-by: Stefan Eichenberger <stefan.eichenberger@toradex.com>
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

The 88W8997 bluetooth module supports setting the max-speed property.
Signed-off-by: Stefan Eichenberger <stefan.eichenberger@toradex.com>
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

Update the documentation with the device tree binding for the Marvell
88W8997 bluetooth device.
Signed-off-by: Stefan Eichenberger <stefan.eichenberger@toradex.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

Remove hardcoded interface number check because Bluetooth specification
since version 4.0 only recommends and no longer requires specific
interface numbers.

While earlier Bluetooth versions, i.e. 2.1 + EDR and 3.0 + HS, contain
required configuration table in Volume 4 - Host Controller Interface
Part B - USB Transport Layer, Bluetooth Core Specification Addendum 2
changes the table from required to recommended configuration.
Signed-off-by: Tomasz Moń <tomasz.mon@nordicsemi.no>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

This makes use of BIT macro when defining bitfields which makes it
clearer what bit it is toggling.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

Pedro Tammela says:

====================
net/sched: act_pedit: minor improvements

This series aims to improve the code and usability of act_pedit for
netlink users.

Patches 1-2 improves error reporting for extended keys parsing with extack.

Patch 3 checks the static offsets a priori on create/update. Currently,
this is done at the datapath for both static and runtime offsets.

Patch 4 removes a check from the datapath which is redundant since the
netlink parsing validates the key types.

Patch 5 changes the 'pr_info()' calls in the datapath to rate limited
versions.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Unbounded info messages in the pedit datapath can flood the printk
ring buffer quite easily depending on the action created.
As these messages are informational, usually printing some, not all,
is enough to bring attention to the real issue.
Reviewed-by: Jamal Hadi Salim <jhs@mojatatu.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Pedro Tammela <pctammela@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The netlink parsing already validates the key 'htype'.
Remove the datapath check as it's redundant.
Reviewed-by: Jamal Hadi Salim <jhs@mojatatu.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Pedro Tammela <pctammela@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Static key offsets should always be on 32 bit boundaries. Validate them on
create/update time for static offsets and move the datapath validation
for runtime offsets only.

iproute2 already errors out if a given offset and data size cannot be
packed to a 32 bit boundary. This change will make sure users which
create/update pedit instances directly via netlink also error out,
instead of finding out when packets are traversing.
Reviewed-by: Jamal Hadi Salim <jhs@mojatatu.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Pedro Tammela <pctammela@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

We have extack available when parsing 'ex' keys, so pass it to
tcf_pedit_keys_ex_parse and add more detailed error messages.
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Pedro Tammela <pctammela@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Transform two checks in the 'ex' key parsing into netlink policies
removing extra if checks.
Signed-off-by: Pedro Tammela <pctammela@mojatatu.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The kernel will print several warnings in a short period of time
when it stalls. Like this:

First warning:
[ 7100.097547] ------------[ cut here ]------------
[ 7100.097550] NETDEV WATCHDOG: eno2 (xxx): transmit queue 8 timed out
[ 7100.097571] WARNING: CPU: 8 PID: 0 at net/sched/sch_generic.c:467
                       dev_watchdog+0x260/0x270
...

Second warning:
[ 7147.756952] rcu: INFO: rcu_preempt self-detected stall on CPU
[ 7147.756958] rcu:   24-....: (59999 ticks this GP) idle=546/1/0x400000000000000
                      softirq=367      3137/3673146 fqs=13844
[ 7147.756960]        (t=60001 jiffies g=4322709 q=133381)
[ 7147.756962] NMI backtrace for cpu 24
...

We calculate that the transmit queue start stall should occur before
7095s according to watchdog_timeo, the rcu start stall at 7087s.
These two times are close together, it is difficult to confirm which
happened first.

To let users know the exact time the stall started, print msecs when
the transmit queue time out.
Signed-off-by: Yajun Deng <yajun.deng@linux.dev>
Signed-off-by: David S. Miller <davem@davemloft.net>

Vladimir Oltean says:

====================
Remove skb_mac_header() dependency in DSA xmit path

Eric started working on removing skb_mac_header() assumptions from the
networking xmit path, and I offered to help for DSA:
https://lore.kernel.org/netdev/20230321164519.1286357-1-edumazet@google.com/

The majority of this patch set is a straightforward replacement of
skb_mac_header() with skb->data (hidden either behind skb_eth_hdr(), or
behind skb_vlan_eth_hdr()). The only patch which is more "interesting"
is 9/9.

Another potential caller of __skb_vlan_pop() on xmit (and therefore
also of skb_mac_header()) is tcf_vlan_act(), but I haven't had the time
to investigate that (enough to submit changes other than what's here).

v1->v2:
- 09/09: document the vlan_tci argument of vlan_remove_tag() in the kdoc

v1 at:
https://lore.kernel.org/netdev/20230322233823.1806736-1-vladimir.oltean@nxp.com/

Cc: Madalin Bucur <madalin.bucur@nxp.com>
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

ocelot_xmit_get_vlan_info() calls __skb_vlan_pop() as the most
appropriate helper I could find which strips away a VLAN header.
That's all I need it to do, but __skb_vlan_pop() has more logic, which
will become incompatible with the future revert of commit 6d1ccff6
("net: reset mac header in dev_start_xmit()").

Namely, it performs a sanity check on skb_mac_header(), which will stop
being set after the above revert, so it will return an error instead of
removing the VLAN tag.

ocelot_xmit_get_vlan_info() gets called in 2 circumstances:

(1) the port is under a VLAN-aware bridge and the bridge sends
    VLAN-tagged packets

(2) the port is under a VLAN-aware bridge and somebody else (an 8021q
    upper) sends VLAN-tagged packets (using a VID that isn't in the
    bridge vlan tables)

In case (1), there is actually no bug to defend against, because
br_dev_xmit() calls skb_reset_mac_header() and things continue to work.

However, in case (2), illustrated using the commands below, it can be
seen that our intervention is needed, since __skb_vlan_pop() complains:

$ ip link add br0 type bridge vlan_filtering 1 && ip link set br0 up
$ ip link set $eth master br0 && ip link set $eth up
$ ip link add link $eth name $eth.100 type vlan id 100 && ip link set $eth.100 up
$ ip addr add 192.168.100.1/24 dev $eth.100

I could fend off the checks in __skb_vlan_pop() with some
skb_mac_header_was_set() calls, but seeing how few callers of
__skb_vlan_pop() there are from TX paths, that seems rather
unproductive.

As an alternative solution, extract the bare minimum logic to strip a
VLAN header, and move it to a new helper named vlan_remove_tag(), close
to the definition of vlan_insert_tag(). Document it appropriately and
make ocelot_xmit_get_vlan_info() call this smaller helper instead.

Seeing that it doesn't appear illegal to test skb->protocol in the TX
path, I guess it would be a good for vlan_remove_tag() to also absorb
the vlan_set_encap_proto() function call.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Once commit 6d1ccff6 ("net: reset mac header in dev_start_xmit()")
will be reverted, it will no longer be true that skb->data points at
skb_mac_header(skb) - since the skb->mac_header will not be set - so
stop saying that, and just say that it points to the MAC header.

I've reviewed vlan_insert_tag() and it does not *actually* depend on
skb_mac_header(), so reword that to avoid the confusion.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This is a cosmetic patch which consolidates the code to use the helper
function offered by if_vlan.h.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

skb_mac_header() will no longer be available in the TX path when
reverting commit 6d1ccff6 ("net: reset mac header in
dev_start_xmit()"). As preparation for that, let's use
skb_vlan_eth_hdr() to get to the VLAN header instead, which assumes it's
located at skb->data (assumption which holds true here).
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

skb_mac_header() will no longer be available in the TX path when
reverting commit 6d1ccff6 ("net: reset mac header in
dev_start_xmit()"). As preparation for that, let's use skb_eth_hdr() to
get to the Ethernet header's MAC DA instead, helper which assumes this
header is located at skb->data (assumption which holds true here).
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

skb_mac_header() will no longer be available in the TX path when
reverting commit 6d1ccff6 ("net: reset mac header in
dev_start_xmit()"). As preparation for that, let's use
skb_vlan_eth_hdr() to get to the VLAN header instead, which assumes it's
located at skb->data (assumption which holds true here).
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

It appears that dpaa_enable_tx_csum() only calls skb_reset_mac_header()
to get to the VLAN header using skb_mac_header().

We can use skb_vlan_eth_hdr() to get to the VLAN header based on
skb->data directly. This avoids spending a few cycles to set
skb->mac_header.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Madalin Bucur <madalin.bucur@oss.nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Similar to skb_eth_hdr() introduced in commit 96cc4b69 ("macvlan: do
not assume mac_header is set in macvlan_broadcast()"), let's introduce a
skb_vlan_eth_hdr() helper which can be used in TX-only code paths to get
to the VLAN header based on skb->data rather than based on the
skb_mac_header(skb).

We also consolidate the drivers that dereference skb->data to go through
this helper.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This is a preparatory change for the deletion of skb_reset_mac_header(skb)
from __dev_queue_xmit(). After that deletion, skb_mac_header(skb) will
no longer be set in TX paths, from which __vlan_insert_inner_tag() can
still be called (perhaps indirectly).

If we don't make this change, then an unset MAC header (equal to ~0U)
will become set after the adjustment with VLAN_HLEN.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch adds support for the Microchip LAN867x 10BASE-T1S family
(LAN8670/1/2). The driver supports P2MP with PLCA.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Ramón Nordin Rodriguez <ramon.nordin.rodriguez@ferroamp.se>
Signed-off-by: David S. Miller <davem@davemloft.net>

Zero-length arrays as fake flexible arrays are deprecated and we are
moving towards adopting C99 flexible-array members instead.

Transform zero-length array into flexible-array member in struct
rxrpc_ackpacket.

Address the following warnings found with GCC-13 and
-fstrict-flex-arrays=3 enabled:
net/rxrpc/call_event.c:149:38: warning: array subscript i is outside array bounds of ‘uint8_t[0]’ {aka ‘unsigned char[]’} [-Warray-bounds=]

This helps with the ongoing efforts to tighten the FORTIFY_SOURCE
routines on memcpy() and help us make progress towards globally
enabling -fstrict-flex-arrays=3 [1].

Link: https://github.com/KSPP/linux/issues/21
Link: https://github.com/KSPP/linux/issues/263
Link: https://gcc.gnu.org/pipermail/gcc-patches/2022-October/602902.html [1]
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Signed-off-by: David Howells <dhowells@redhat.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Jeffrey Altman <jaltman@auristor.com>
cc: Marc Dionne <marc.dionne@auristor.com>
cc: "David S. Miller" <davem@davemloft.net>
cc: Eric Dumazet <edumazet@google.com>
cc: Jakub Kicinski <kuba@kernel.org>
cc: Paolo Abeni <pabeni@redhat.com>
cc: linux-afs@lists.infradead.org
cc: netdev@vger.kernel.org
cc: linux-hardening@vger.kernel.org
Link: https://lore.kernel.org/r/ZAZT11n4q5bBttW0@work/Signed-off-by: David S. Miller <davem@davemloft.net>

Eric Dumazet says:

====================
net: give napi_threaded_poll() some love

There is interest to revert commit 4cd13c21
("softirq: Let ksoftirqd do its job") and use instead the
napi_threaded_poll() mode.

https://lore.kernel.org/netdev/140f61e2e1fcb8cf53619709046e312e343b53ca.camel@redhat.com/T/#m8a8f5b09844adba157ad0d22fc1233d97013de50

Before doing so, make sure napi_threaded_poll() benefits
from recent core stack improvements, to further reduce
softirq triggers.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

We use napi_threaded_poll() in order to reduce our softirq dependency.

We can add a followup of 821eba96 ("net: optimize napi_schedule_rps()")
to further remove the need of firing NET_RX_SOFTIRQ whenever
RPS/RFS are used.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

If we call skb_defer_free_flush() from napi_threaded_poll(),
we can avoid to raise IPI from skb_attempt_defer_free()
when the list becomes too big.

This allows napi_threaded_poll() to rely less on softirqs,
and lowers latency caused by a too big list.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

We plan using skb_defer_free_flush() from napi_threaded_poll()
in the following patch.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

kfree_skb() can be called from hard irq handlers,
but skb_attempt_defer_free() is meant to be used
from process or BH contexts, and skb_defer_free_flush()
is meant to be called from BH contexts.

Not having to mask hard irq can save some cycles.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Make sure skbs that are stored in softnet_data.defer_list
do not have a dst attached.

Also make sure the the skb was orphaned.

Link: https://lore.kernel.org/netdev/CANn89iJuEVe72bPmEftyEJHLzzN=QNR2yueFjTxYXCEpS5S8HQ@mail.gmail.com/T/Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Tony Nguyen says:

====================
This series lowers the CPU usage of the ice driver when using its
provided /dev/gnss*.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Older chips (like MT7622) use a different bit in ib2 to enable hardware
counter support. Add macros for both and select the appropriate bit.

Fixes: 3fbe4d8c ("net: ethernet: mtk_eth_soc: ppe: add support for flow accounting")
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Saeed Mahameed says:

====================
mlx5-updates-2023-04-20

1) Dragos Improves RX page pool, and provides some fixes to his previous
   series:
 1.1) Fix releasing page_pool for striding RQ and legacy RQ nonlinear case
 1.2) Hook NAPIs to page pools to gain more performance.

2) From Roi, Some cleanups to TC and eswitch modules.

3) Maher migrates vnic diagnostic counters reporting from debugfs to a
    dedicated devlink health reporter

Maher Says:
===========
 net/mlx5: Expose vnic diagnostic counters using devlink

Currently, vnic diagnostic counters are exposed through the following
debugfs:

$ ls /sys/kernel/debug/mlx5/0000:08:00.0/esw/vf_0/vnic_diag/
cq_overrun
quota_exceeded_command
total_q_under_processor_handle
invalid_command
send_queue_priority_update_flow
nic_receive_steering_discard

The current design does not allow the hypervisor to view the diagnostic
counters of its VFs, in case the VFs get bound to a VM. In other words,
the counters are not exposed for representor interfaces.
Furthermore, the debugfs design is inconvenient future-wise, in case more
counters need to be reported by the driver in the future.

As these counters pertain to vNIC health, it is more appropriate to
utilize the devlink health reporter to expose them.

Thus, this patchest includes the following changes:

* Drop the current vnic diagnostic counters debugfs interface.
* Add a vnic devlink health reporter for PFs/VFs core devices, which
  when diagnosed will dump vnic diagnostic counter values that are
  queried from FW.
* Add a vnic devlink health reporter for the representor interface, which
  serves the same purpose listed in the previous point, in addition to
  allowing the hypervisor to view its VFs diagnostic counters, even when
  the VFs are bounded to external VMs.

Example of devlink health reporter usage is:
$devlink health diagnose pci/0000:08:00.0 reporter vnic
 vNIC env counters:
    total_error_queues: 0 send_queue_priority_update_flow: 0
    comp_eq_overrun: 0 async_eq_overrun: 0 cq_overrun: 0
    invalid_command: 0 quota_exceeded_command: 0
    nic_receive_steering_discard: 0

===========

4) SW steering fixes and improvements

Yevgeny Kliteynik Says:
=======================
These short patch series are just small fixes / improvements for
SW steering:

 - Patch 1: Fix dumping of legacy modify_hdr in debug dump to
   align to what is expected by parser
 - Patch 2: Have separate threshold for ICM sync per ICM type
 - Patch 3: Add more info to the steering debug dump - Linux
   version and device name
 - Patch 4: Keep track of number of buddies that are currently
   in use per domain per buddy type

=======================

* tag 'mlx5-updates-2023-04-20' of git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux:
  net/mlx5: Update op_mode to op_mod for port selection
  net/mlx5: E-Switch, Remove unused mlx5_esw_offloads_vport_metadata_set()
  net/mlx5: E-Switch, Remove redundant dev arg from mlx5_esw_vport_alloc()
  net/mlx5: Include linux/pci.h for pci_msix_can_alloc_dyn()
  net/mlx5e: RX, Hook NAPIs to page pools
  net/mlx5e: RX, Fix XDP_TX page release for legacy rq nonlinear case
  net/mlx5e: RX, Fix releasing page_pool pages twice for striding RQ
  net/mlx5e: Add vnic devlink health reporter to representors
  net/mlx5: Add vnic devlink health reporter to PFs/VFs
  Revert "net/mlx5: Expose vnic diagnostic counters for eswitch managed vports"
  Revert "net/mlx5: Expose steering dropped packets counter"
  net/mlx5: DR, Add memory statistics for domain object
  net/mlx5: DR, Add more info in domain dbg dump
  net/mlx5: DR, Calculate sync threshold of each pool according to its type
  net/mlx5: DR, Fix dumping of legacy modify_hdr in debug dump
====================

Link: https://lore.kernel.org/r/20230421013850.349646-1-saeed@kernel.orgSigned-off-by: Jakub Kicinski <kuba@kernel.org>