When MES is enabled KIQ is not available.  Return an error
when someone uses the debugfs preempt test interface in
that case.
Acked-by: Srinivasan Shanmugam <srinivasan.shanmugam@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

When MES is enabled KIQ is not available.  Return an error
when someone uses the debugfs preempt test interface in
that case.
Acked-by: Srinivasan Shanmugam <srinivasan.shanmugam@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

[Why]

DCN IPS interoperates with other system idle power features, such as
Zstates.

On DCN35, there is a known issue where system Z8 + DCN IPS2 causes a
hard hang. We observe this on systems where the SBIOS allows Z8.

Though there is a SBIOS fix, there's no guarantee that users will get it
any time soon, or even install it. A workaround is needed to prevent
this from rearing its head in the wild.

[How]

For DCN35, check the pmfw version to determine whether the SBIOS has the
fix. If not, set IPS1+RCG as the deepest possible state in all cases
except for s0ix and display off (DPMS). Otherwise, enable all IPS
Signed-off-by: Leo Li <sunpeng.li@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

log message "Dumping IP State Completed" needs to
be logged only once when state dumping is complete.

Hence moving it out of the for loop.
Signed-off-by: Sunil Khatri <sunil.khatri@amd.com>
Acked-by: Trigger Huang <Trigger.Huang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

[background] when unloading amdgpu driver right after running a
workload, drain_workqueue is causing "Fence fallback timer
expired on ring sdma0.0". Under sriov, this issue will cause sriov
full access timeout and a reset happening.

move drain_workqueue before shutdown is set to allow ih process and
before enter full access under sriov to avoid full access time cost.
Signed-off-by: Victor Zhao <Victor.Zhao@amd.com>
Reviewed-by: Feifei Xu <Feifei.Xu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Do the coredump immediately after a job timeout to get a closer
representation of GPU's error status.

V2: This will skip printing vram_lost as the GPU reset is not
happened yet (Alex)

V3: Unconditionally call the core dump as we care about all the reset
functions(soft-recovery and queue reset and full adapter reset, Alex)

V4: Do the dump after adev->job_hang = true (Sunil)
Signed-off-by: Trigger Huang <Trigger.Huang@amd.com>
Acked-by: Sunil Khatri <sunil.khatri@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

The vm lost status can only be obtained after a GPU reset occurs, but
sometimes a dev core dump can be happened before GPU reset. So a new
argument is added to tell the dev core dump implementation whether to
skip printing the vram_lost status in the dump.
And this patch is also trying to decouple the core dump function from
the GPU reset function, by replacing the argument amdgpu_reset_context
with amdgpu_job to specify the context for core dump.

V2: Inform user if VRAM lost check is skipped so users don't assume
VRAM wasn't lost (Alex)
Signed-off-by: Trigger Huang <Trigger.Huang@amd.com>
Suggested-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Pending extended validation.
Reviewed-and-tested-by: Jiadong Zhu <Jiadong.Zhu@amd.com>
Acked-by: Felix Kuehling <felix.kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Add this flag to enable experimental resets for testing before they
are fully validated.
Reviewed-and-tested-by: Jiadong Zhu <Jiadong.Zhu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

[why]
It is to fix in try_disable_dsc() due to misrevert of
commit 338567d1 ("drm/amd/display: Fix MST BW calculation Regression")

[How]
Fix restoring minimum compression bw by 'max_kbps', instead of native bw 'stream_kbps'
Signed-off-by: Fangzhi Zuo <Jerry.Zuo@amd.com>
Reviewed-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Always reprogram the hardware state on init.  This ensures
the PMFW state is explicitly programmed and we are not relying
on the default PMFW state.

Closes: https://gitlab.freedesktop.org/drm/amd/-/issues/3131Reviewed-by: Kenneth Feng <kenneth.feng@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Remove unnecessary TODO from spl_os_types.h
Reviewed-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Zaeem Mohamed <zaeem.mohamed@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Use appropriate SPDX copyright for spl_os_types.h
Reviewed-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Zaeem Mohamed <zaeem.mohamed@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Add DSC log in each critical routines to facilitate debugging.
Reviewed-by: Rodrigo Siqueira <rodrigo.siqueira@amd.com>
Signed-off-by: Fangzhi Zuo <Jerry.Zuo@amd.com>
Signed-off-by: Zaeem Mohamed <zaeem.mohamed@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

This version brings along the following fixes:
- Fix MS/MP mismatches in dml21 for dcn401
- Resolved Coverity issues
- Add back quality EASF and ISHARP and dc dependency changes
- Add sharpness support for windowed YUV420 video
- Add improvements for text display and HDR DWM and MPO
- Fix Synaptics Cascaded Panamera DSC Determination
- Allocate DCN35 clock table transfer buffers in GART
- Add Replay Low Refresh Rate parameters in dc type
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Aric Cyr <aric.cyr@amd.com>
Signed-off-by: Zaeem Mohamed <zaeem.mohamed@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

[Why]
Previous only applied sharpness for fullscreen YUV420 video.

[How]
Remove fullscrene restriction and apply sharpness for windowed
 YUV420 video as well.
Reviewed-by: Jun Lei <jun.lei@amd.com>
Signed-off-by: Samson Tam <Samson.Tam@amd.com>
Signed-off-by: Zaeem Mohamed <zaeem.mohamed@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

[Why]
Tune settings for improved text display.
Handle differences between DWM and MPO in HDR path.

[How]
Update sharpener LBA table.
Use HDR multiplier to calculate scalar matrix coefficients
 for HDR RGB MPO path.
Update unit tests.
Reviewed-by: Jun Lei <jun.lei@amd.com>
Signed-off-by: Samson Tam <Samson.Tam@amd.com>
Signed-off-by: Zaeem Mohamed <zaeem.mohamed@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Why:
To supported Low Refresh Rate panel for Replay Feature,
Adding some parameters to record Low Refresh Rate information.
Reviewed-by: Robin Chen <robin.chen@amd.com>
Signed-off-by: Dennis Chan <dennis.chan@amd.com>
Signed-off-by: Zaeem Mohamed <zaeem.mohamed@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

[Why]
Addressed previous issues with quality changes and new issues due to
 rolling back quality changes.

[How]
This reverts commit f9e67598, fixes merge conflicts, and fixed some
 formatting errors.
Store current sharpness level for each pregen table to minimize
 calculating sharpness table every time.
Disable dynamic ODM when sharpness is enabled.
Reviewed-by: Jun Lei <jun.lei@amd.com>
Signed-off-by: Samson Tam <Samson.Tam@amd.com>
Signed-off-by: Zaeem Mohamed <zaeem.mohamed@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

[Why]
We want to avoid arming the HPD timer in firmware when preparing for
S0i3 entry when DC is considered in D3.

[How]
Notify DMCUB of the power state transitions so it can decide to arm
the HPD timer for idle in DCN35 only in D0.
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Ovidiu Bunea <Ovidiu.Bunea@amd.com>
Signed-off-by: Zaeem Mohamed <zaeem.mohamed@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Synaptics Cascaded Panamera topology needs to unconditionally
acquire root aux for dsc decoding.
Reviewed-by: Roman Li <roman.li@amd.com>
Signed-off-by: Fangzhi Zuo <Jerry.Zuo@amd.com>
Signed-off-by: Zaeem Mohamed <zaeem.mohamed@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

[Why]
Because sometime DMUB GPINT will time out,
 it will cause we return 0 as residency number.

[How]
Retry to avoid this happened.
Reviewed-by: Robin Chen <robin.chen@amd.com>
Signed-off-by: ChunTao Tso <ChunTao.Tso@amd.com>
Signed-off-by: Zaeem Mohamed <zaeem.mohamed@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

[Why]
Request from PMFW to use GART for clock table transfer tables as
framebuffer is being deprecated on APU.

[How]
Switch over to GART via the allocation flag.
Reviewed-by: Sung joon Kim <sungjoon.kim@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Zaeem Mohamed <zaeem.mohamed@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

translate_by_source need not be set for DCN401 onwards since cursor
cursor composition comes after scaler in the hardware pipeline.
Hence offset calculation has been reworked, and this setting is not
necessary to be enabled anymore.
Reviewed-by: Rodrigo Siqueira <rodrigo.siqueira@amd.com>
Signed-off-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Zaeem Mohamed <zaeem.mohamed@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

[WHY]
Remove coverity issues that were originally ignored.

[HOW]
Ran coverity locally on driver, used output report to find existing
coverity issues, resolved them
Reviewed-by: Nicholas Choi <nicholas.choi@amd.com>
Signed-off-by: Daniel Sa <Daniel.Sa@amd.com>
Signed-off-by: Zaeem Mohamed <zaeem.mohamed@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

[WHY]
Prefetch calculations did not guarantee that bandwidth required in
mode support was less than mode programming which can cause failures.

[HOW]
Fix bandwidth calculations to assume fixed times for OTO schedule,
and choose which schedule to use based on time to fetch pixel data.
Reviewed-by: Jun Lei <jun.lei@amd.com>
Signed-off-by: Dillon Varone <dillon.varone@amd.com>
Signed-off-by: Zaeem Mohamed <zaeem.mohamed@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

[Description]
Before every full update we must wait for all pending updates to be
cleared - this is particularly important for minimal transitions
because if we don't wait for pending cleared, it will be as if
there was no minimal transition at all. In OTG we must read 3 different
status registers for pending cleared, one specifically for OTG updates,
one specifically for OPTC updates, and the last for surface related
updates
Reviewed-by: Dillon Varone <dillon.varone@amd.com>
Signed-off-by: Alvin Lee <Alvin.Lee2@amd.com>
Signed-off-by: Zaeem Mohamed <zaeem.mohamed@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

[why]
post_divider_value should not be 0.
Reviewed-by: Charlene Liu <charlene.liu@amd.com>
Signed-off-by: Ahmed, Muhammad <Ahmed.Ahmed@amd.com>
Signed-off-by: Zaeem Mohamed <zaeem.mohamed@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

[Description]
Skipping clock updates is not a hard requirement for overclocking
and only an optimization. Remove the skip as this can cause issues
for FAMS transitions during the overclock sequence. If FAMS
is enabled we must disable UCLK switch on any full update (which
requires update clocks to be called).
Reviewed-by: Dillon Varone <dillon.varone@amd.com>
Signed-off-by: Alvin Lee <Alvin.Lee2@amd.com>
Signed-off-by: Zaeem Mohamed <zaeem.mohamed@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

[Why]

Idle power states (IPS) describe levels of power-gating within DCN. DM
and DC is responsible for ensuring that we are out of IPS before any DCN
programming happens. Any DCN programming while we're in IPS leads to
undefined behavior (mostly hangs).

Because IPS intersects with all display features, the ability to disable
IPS by default while ironing out the known issues is desired. However,
disabing it completely will cause important features such as s0ix entry
to fail.

Therefore, more granular IPS debug flags are desired.

[How]

Extend the dc debug mask bits to include the available list of IPS
debug flags.

All the flags should work as documented, with the exception of
IPS_DISABLE_DYNAMIC. It requires dm changes which will be done in
later changes.

v2: enable docs and fix docstring format
Signed-off-by: Leo Li <sunpeng.li@amd.com>
Reviewed-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Print the index for the profiles.

Closes: https://gitlab.freedesktop.org/drm/amd/-/issues/3543Reviewed-by: Kenneth Feng <kenneth.feng@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

No change in functionality for the current code, but we
need to set the index properly before changing it if we
ever use a non-0 index.
Reviewed-by: Kenneth Feng <kenneth.feng@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

The kernel doc says you need to select manual mode to
adjust this, but the code only allows you to adjust it when
manual mode is not selected.  Remove the manual mode check.
Reviewed-by: Kenneth Feng <kenneth.feng@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Merge tag 'amd-drm-next-6.12-2024-08-26' of https://gitlab.freedesktop.org/agd5f/linux into drm-next

amd-drm-next-6.12-2024-08-26:

amdgpu:
- SDMA devcoredump support
- DCN 4.0.1 updates
- DC SUBVP fixes
- Refactor OPP in DC
- Refactor MMHUBBUB in DC
- DC DML 2.1 updates
- DC FAMS2 updates
- RAS updates
- GFX12 updates
- VCN 4.0.3 updates
- JPEG 4.0.3 updates
- Enable wave kill (soft recovery) for compute queues
- Clean up CP error interrupt handling
- Enable CP bad opcode interrupts
- VCN 4.x fixes
- VCN 5.x fixes
- GPU reset fixes
- Fix vbios embedded EDID size handling
- SMU 14.x updates
- Misc code cleanups and spelling fixes
- VCN devcoredump support
- ISP MFD i2c support
- DC vblank fixes
- GFX 12 fixes
- PSR fixes
- Convert vbios embedded EDID to drm_edid
- DCN 3.5 updates
- DMCUB updates
- Cursor fixes
- Overdrive support for SMU 14.x
- GFX CP padding optimizations
- DCC fixes
- DSC fixes
- Preliminary per queue reset infrastructure
- Initial per queue reset support for GFX 9
- Initial per queue reset support for GFX 7, 8
- DCN 3.2 fixes
- DP MST fixes
- SR-IOV fixes
- GFX 9.4.3/4 devcoredump support
- Add process isolation framework
- Enable process isolation support for GFX 9.4.3/4
- Take IOMMU remapping into account for P2P DMA checks

amdkfd:
- CRIU fixes
- Improved input validation for user queues
- HMM fix
- Enable process isolation support for GFX 9.4.3/4
- Initial per queue reset support for GFX 9
- Allow users to target recommended SDMA engines

radeon:
- remove .load and drm_dev_alloc
- Fix vbios embedded EDID size handling
- Convert vbios embedded EDID to drm_edid
- Use GEM references instead of TTM
- r100 cp init cleanup
- Fix potential overflows in evergreen CS offset tracking

UAPI:
- KFD support for targetting queues on recommended SDMA engines
  Proposed userspace:
  https://github.com/ROCm/ROCR-Runtime/commit/2f588a24065f41c208c3701945e20be746d8faf7
  https://github.com/ROCm/ROCR-Runtime/commit/eb30a5bbc7719c6ffcf2d2dd2878bc53a47b3f30

drm/buddy:
- Add start address support for trim function

From: Alex Deucher <alexander.deucher@amd.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240826201528.55307-1-alexander.deucher@amd.com

amdgpu pr conconflicts due to patches cherry-picked to -fixes, I might
as well catch up with a backmerge and handle them all. Plus both misc
and intel maintainers asked for a backmerge anyway.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

Merge tag 'drm-intel-gt-next-2024-08-23' of https://gitlab.freedesktop.org/drm/i915/kernel into drm-next

UAPI Changes:

- Limit the number of relocations to INT_MAX (Tvrtko)

  Only impact should be synthetic tests.

Driver Changes:

- Fix for #11396: GPU Hang and rcs0 reset on Cherrytrail platform
- Fix Virtual Memory mapping boundaries calculation (Andi)
- Fix for #11255: Long hangs in buddy allocator with DG2/A380 without
  Resizable BAR since 6.9 (David)
- Mark the GT as dead when mmio is unreliable (Chris, Andi)
- Workaround additions / fixes for MTL, ARL and DG2 (John H, Nitin)
- Enable partial memory mapping of GPU virtual memory (Andi, Chris)

- Prevent NULL deref on intel_memory_regions_hw_probe (Jonathan, Dan)
- Avoid UAF on intel_engines_release (Krzysztof)

- Don't update PWR_CLK_STATE starting Gen12 (Umesh)
- Code and dmesg cleanups (Andi, Jesus, Luca)
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
From: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/ZshcfSqgfnl8Mh4P@jlahtine-mobl.ger.corp.intel.com

Merge tag 'drm-misc-next-2024-08-22' of https://gitlab.freedesktop.org/drm/misc/kernel into drm-next

drm-misc-next for v6.12:

Cross-subsystem Changes:

string:
- add mem_is_zero()

Core Changes:

edid:
- use mem_is_zero()

Driver Changes:

ast:
- reorganize output code by type (VGA, DP, etc)
- convert to struct drm_edid
- fix BMC handling for all outputs

bridge:
- anx7625: simplify OF array handling
- dw-hdmi: simplify clock handling
- lontium-lt8912b: fix mode validation
- nwl-dsi: fix mode vsync/hsync polarity

panel:
- ili9341: fix comments
- jd9365da: fix "exit sleep" commands
- jdi-fhd-r63452: simplify error handling with DSI multi-style
  helpers
- mantix-mlaf057we51: simplify error handling with DSI multi-style
  helpers
- simple: support Innolux G070ACE-LH3 plus DT bindings; support
  On Tat Industrial Company KD50G21-40NT-A1 plus DT bindings
- st7701: decouple DSI and DRM code; add SPI support; support Anbernic
  RG28XX plus DT bindings

vc4:
- fix PM during detect
- replace DRM_ERROR() with drm_error()
- v3d: simplify clock retrieval
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
From: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20240822150710.GA243952@localhost.localdomain

Pull bcachefs fixes from Kent Overstreet:

 - assorted syzbot fixes

 - some upgrade fixes for old (pre 1.0) filesystems

 - fix for moving data off a device that was switched to durability=0
   after data had been written to it.

 - nocow deadlock fix

 - fix for new rebalance_work accounting

* tag 'bcachefs-2024-08-24' of git://evilpiepirate.org/bcachefs: (28 commits)
  bcachefs: Fix rebalance_work accounting
  bcachefs: Fix failure to flush moves before sleeping in copygc
  bcachefs: don't use rht_bucket() in btree_key_cache_scan()
  bcachefs: add missing inode_walker_exit()
  bcachefs: clear path->should_be_locked in bch2_btree_key_cache_drop()
  bcachefs: Fix double assignment in check_dirent_to_subvol()
  bcachefs: Fix refcounting in discard path
  bcachefs: Fix compat issue with old alloc_v4 keys
  bcachefs: Fix warning in bch2_fs_journal_stop()
  fs/super.c: improve get_tree() error message
  bcachefs: Fix missing validation in bch2_sb_journal_v2_validate()
  bcachefs: Fix replay_now_at() assert
  bcachefs: Fix locking in bch2_ioc_setlabel()
  bcachefs: fix failure to relock in btree_node_fill()
  bcachefs: fix failure to relock in bch2_btree_node_mem_alloc()
  bcachefs: unlock_long() before resort in journal replay
  bcachefs: fix missing bch2_err_str()
  bcachefs: fix time_stats_to_text()
  bcachefs: Fix bch2_bucket_gens_init()
  bcachefs: Fix bch2_trigger_alloc assert
  ...

Pull smb server fixes from Steve French:

 - query directory flex array fix

 - fix potential null ptr reference in open

 - fix error message in some open cases

 - two minor cleanups

* tag '6.11-rc5-server-fixes' of git://git.samba.org/ksmbd:
  smb/server: update misguided comment of smb2_allocate_rsp_buf()
  smb/server: remove useless assignment of 'file_present' in smb2_open()
  smb/server: fix potential null-ptr-deref of lease_ctx_info in smb2_open()
  smb/server: fix return value of smb2_open()
  ksmbd: the buffer of smb2 query dir response has at least 1 byte