Skip to content

L
linux
Switch branch/tag
  1. 08 Dec, 2010 3 commits
  3. 07 Dec, 2010 2 commits
    • Anssi Hannula's avatar
      ALSA: hda - Always allow basic audio irrespective of ELD info · 3dc86429
      Anssi Hannula authored 
      Commit bbbe3390 added functionality to restrict PCM parameters
based on ELD info (derived from EDID data) of the audio sink.

However, according to CEA-861-D no SAD is needed for basic audio
(32/44.1/48kHz stereo 16-bit audio), which is instead indicated with a
basic audio flag in the CEA EDID Extension.

The flag is not present in ELD. However, as all audio capable sinks are
required to support basic audio, we can assume it to be always
available.

Fix allowed audio formats with sinks that have SADs (Short Audio
Descriptors) which do not completely overlap with the basic audio
formats (there are no reports of affected devices so far) by always
assuming that basic audio is supported.
Reported-by: default avatarStephen Warren <swarren@nvidia.com>
Signed-off-by: default avatarAnssi Hannula <anssi.hannula@iki.fi>
Cc: stable@kernel.org
Signed-off-by: default avatarTakashi Iwai <tiwai@suse.de>
      3dc86429
    • Anssi Hannula's avatar
      ALSA: hda - Do not wrongly restrict min_channels based on ELD · 4b0dbdb1
      Anssi Hannula authored 
      Commit bbbe3390 added functionality to restrict PCM parameters
based on ELD info (derived from EDID data) of the audio sink.

However, it wrongly assumes that the bits 0-2 of the first byte of
CEA Short Audio Descriptors mean a supported number of channels. In
reality, they mean the maximum number of channels (as per CEA-861-D
7.5.2). This means that the channel count can only be used to restrict
max_channels, not min_channels.

Restricting min_channels causes us to deny opening the device in stereo
mode if the sink only has SADs that declare larger numbers of channels
(like Primare SP32 AV Processor does).

Fix that by not restricting min_channels based on ELD information.
Signed-off-by: default avatarAnssi Hannula <anssi.hannula@iki.fi>
Reported-by: default avatarJean-Yves Avenard <jyavenard@gmail.com>
Tested-by: default avatarJean-Yves Avenard <jyavenard@gmail.com>
Cc: stable@kernel.org
Signed-off-by: default avatarTakashi Iwai <tiwai@suse.de>
      4b0dbdb1
  5. 06 Dec, 2010 1 commit
  7. 05 Dec, 2010 1 commit
  9. 04 Dec, 2010 1 commit
  11. 03 Dec, 2010 6 commits
  13. 02 Dec, 2010 1 commit
  15. 30 Nov, 2010 1 commit
  17. 29 Nov, 2010 3 commits
  19. 26 Nov, 2010 1 commit
  21. 25 Nov, 2010 1 commit
  23. 24 Nov, 2010 2 commits
  25. 23 Nov, 2010 10 commits
  27. 22 Nov, 2010 7 commits
    • Jeremy Fitzhardinge's avatar
      Merge branches 'upstream/core', 'upstream/xenfs' and 'upstream/evtchn' into upstream/for-linus · 9b832153
      Jeremy Fitzhardinge authored 
      * upstream/core:
  xen/events: Use PIRQ instead of GSI value when unmapping MSI/MSI-X irqs.
  xen: set IO permission early (before early_cpu_init())
  xen: re-enable boot-time ballooning
  xen/balloon: make sure we only include remaining extra ram
  xen/balloon: the balloon_lock is useless
  xen: add extra pages to balloon
  xen/events: use locked set|clear_bit() for cpu_evtchn_mask
  xen/evtchn: clear secondary CPUs' cpu_evtchn_mask[] after restore
  xen: implement XENMEM_machphys_mapping

* upstream/xenfs:
  Revert "xen/privcmd: create address space to allow writable mmaps"
  xen/xenfs: update xenfs_mount for new prototype
  xen: fix header export to userspace
  xen: set vma flag VM_PFNMAP in the privcmd mmap file_op
  xen: xenfs: privcmd: check put_user() return code

* upstream/evtchn:
  xen: make evtchn's name less generic
  xen/evtchn: the evtchn device is non-seekable
  xen/evtchn: add missing static
  xen/evtchn: Fix name of Xen event-channel device
  xen/evtchn: don't do unbind_from_irqhandler under spinlock
  xen/evtchn: remove spurious barrier
  xen/evtchn: ports start enabled
  xen/evtchn: dynamically allocate port_user array
  xen/evtchn: track enabled state for each port
      9b832153
    • Konrad Rzeszutek Wilk's avatar
      xen/events: Use PIRQ instead of GSI value when unmapping MSI/MSI-X irqs. · 12334715
      Konrad Rzeszutek Wilk authored 
      When we allocate a vector for MSI/MSI-X we save away the PIRQ, and the
vector value. When we unmap (de-allocate) the MSI/MSI-X vector(s) we
need to provide the PIRQ and the vector value. What we did instead
was to provide the GSI (which was zero) and the vector value, and we
got these unhappy error messages:

(XEN) irq.c:1575: dom0: pirq 0 not mapped
[    7.733415] unmap irq failed -22

This patches fixes this and we use the PIRQ value instead of the GSI
value.

CC: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
Signed-off-by: default avatarKonrad Rzeszutek Wilk <konrad.wilk@oracle.com>
      12334715
    • Konrad Rzeszutek Wilk's avatar
      xen: set IO permission early (before early_cpu_init()) · ec35a69c
      Konrad Rzeszutek Wilk authored 
      This patch is based off "xen dom0: Set up basic IO permissions for dom0."
by Juan Quintela <quintela@redhat.com>.

On AMD machines when we boot the kernel as Domain 0 we get this nasty:

mapping kernel into physical memory
Xen: setup ISA identity maps
about to get started...
(XEN) traps.c:475:d0 Unhandled general protection fault fault/trap [#13] on VCPU 0 [ec=0000]
(XEN) domain_crash_sync called from entry.S
(XEN) Domain 0 (vcpu#0) crashed on cpu#0:
(XEN) ----[ Xen-4.1-101116  x86_64  debug=y  Not tainted ]----
(XEN) CPU:    0
(XEN) RIP:    e033:[<ffffffff8130271b>]
(XEN) RFLAGS: 0000000000000282   EM: 1   CONTEXT: pv guest
(XEN) rax: 000000008000c068   rbx: ffffffff8186c680   rcx: 0000000000000068
(XEN) rdx: 0000000000000cf8   rsi: 000000000000c000   rdi: 0000000000000000
(XEN) rbp: ffffffff81801e98   rsp: ffffffff81801e50   r8:  ffffffff81801eac
(XEN) r9:  ffffffff81801ea8   r10: ffffffff81801eb4   r11: 00000000ffffffff
(XEN) r12: ffffffff8186c694   r13: ffffffff81801f90   r14: ffffffffffffffff
(XEN) r15: 0000000000000000   cr0: 000000008005003b   cr4: 00000000000006f0
(XEN) cr3: 0000000221803000   cr2: 0000000000000000
(XEN) ds: 0000   es: 0000   fs: 0000   gs: 0000   ss: e02b   cs: e033
(XEN) Guest stack trace from rsp=ffffffff81801e50:

RIP points to read_pci_config() function.

The issue is that we don't set IO permissions for the Linux kernel early enough.

The call sequence used to be:

    xen_start_kernel()
	x86_init.oem.arch_setup = xen_setup_arch;
        setup_arch:
           - early_cpu_init
               - early_init_amd
                  - read_pci_config
           - x86_init.oem.arch_setup [ xen_arch_setup ]
               - set IO permissions.

We need to set the IO permissions earlier on, which this patch does.
Acked-by: default avatarJeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Signed-off-by: default avatarKonrad Rzeszutek Wilk <konrad.wilk@oracle.com>
      ec35a69c
    • David Daney's avatar
      of/phylib: Use device tree properties to initialize Marvell PHYs. · cf41a51d
      David Daney authored 
      Some aspects of PHY initialization are board dependent, things like
indicator LED connections and some clocking modes cannot be determined
by probing.  The dev_flags element of struct phy_device can be used to
control these things if an appropriate value can be passed from the
Ethernet driver.  We run into problems however if the PHY connections
are specified by the device tree.  There is no way for the Ethernet
driver to know what flags it should pass.

If we are using the device tree, the struct phy_device will be
populated with the device tree node corresponding to the PHY, and we
can extract extra configuration information from there.

The next question is what should the format of that information be?
It is highly device specific, and the device tree representation
should not be tied to any arbitrary kernel defined constants.  A
straight forward representation is just to specify the exact bits that
should be set using the "marvell,reg-init" property:

      phy5: ethernet-phy@5 {
        reg = <5>;
        compatible = "marvell,88e1149r";
        marvell,reg-init =
                /* led[0]:1000, led[1]:100, led[2]:10, led[3]:tx */
                <3 0x10 0 0x5777>, /* Reg 3,16 <- 0x5777 */
                /* mix %:0, led[0123]:drive low off hiZ */
                <3 0x11 0 0x00aa>, /* Reg 3,17 <- 0x00aa */
                /* default blink periods. */
                <3 0x12 0 0x4105>, /* Reg 3,18 <- 0x4105 */
                /* led[4]:rx, led[5]:dplx, led[45]:drive low off hiZ */
                <3 0x13 0 0x0a60>; /* Reg 3,19 <- 0x0a60 */
      };

      phy6: ethernet-phy@6 {
        reg = <6>;
        compatible = "marvell,88e1118";
        marvell,reg-init =
                /* Fix rx and tx clock transition timing */
                <2 0x15 0xffcf 0>, /* Reg 2,21 Clear bits 4, 5 */
                /* Adjust LED drive. */
                <3 0x11 0 0x442a>, /* Reg 3,17 <- 0442a */
                /* irq, blink-activity, blink-link */
                <3 0x10 0 0x0242>; /* Reg 3,16 <- 0x0242 */
      };

The Marvell PHYs have a page select register at register 22 (0x16), we
can specify any register by its page and register number.  These are
the first and second word.  The third word contains a mask to be ANDed
with the existing register value, and the fourth word is ORed with the
result to yield the new register value.  The new marvell_of_reg_init
function leaves the page select register unchanged, so a call to it
can be dropped into the .config_init functions without unduly
affecting the state of the PHY.

If CONFIG_OF_MDIO is not set, there is no of_node, or no
"marvell,reg-init" property, the PHY initialization is unchanged.
Signed-off-by: default avatarDavid Daney <ddaney@caviumnetworks.com>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Cyril Chemparathy <cyril@ti.com>
Cc: David Daney <ddaney@caviumnetworks.com>
Cc: Arnaud Patard <arnaud.patard@rtp-net.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Reviewed-by: default avatarGrant Likely <grant.likely@secretlab.ca>
Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
      cf41a51d
    • David Daney's avatar
      phylib: Add support for Marvell 88E1149R devices. · 90600732
      David Daney authored 
      The 88E1149R is 10/100/1000 quad-gigabit Ethernet PHY.  The
.config_aneg function can be shared with 88E1118, but it needs its own
.config_init.
Signed-off-by: default avatarDavid Daney <ddaney@caviumnetworks.com>
Cc: Cyril Chemparathy <cyril@ti.com>
Cc: Arnaud Patard <arnaud.patard@rtp-net.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
      90600732
    • David Daney's avatar
      phylib: Use common page register definition for Marvell PHYs. · 27d916d6
      David Daney authored 
      The definition of the Marvell PHY page register is not specific to
88E1121, so rename the macro to MII_MARVELL_PHY_PAGE, and use it
throughout.
Suggested-by: default avatarCyril Chemparathy <cyril@ti.com>
Signed-off-by: default avatarDavid Daney <ddaney@caviumnetworks.com>
Cc: Cyril Chemparathy <cyril@ti.com>
Cc: Arnaud Patard <arnaud.patard@rtp-net.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
      27d916d6
    • Sonny Rao's avatar
      qlge: Fix incorrect usage of module parameters and netdev msg level · 84cf7029
      Sonny Rao authored 
      Driver appears to be mistaking the permission field with default value
in the case of debug and qlge_irq_type.

Driver is also passing debug as a bitmask into netif_msg_init()
which wants a number of bits.  Ron Mercer suggests we should
change this to pass in -1 so the defaults get used instead,
which makes the default much less verbose.
Signed-off-by: default avatarMilton Miller <miltonm@bga.com>
Signed-off-by: default avatarSonny Rao <sonnyrao@linux.vnet.ibm.com>
Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
      84cf7029
GitLab Nexedi Edition | About GitLab | About Nexedi | 沪ICP备2021021310号-2 | 沪ICP备2021021310号-7