- 12 Dec, 2013 18 commits
-
-
Ludovic Desroches authored
commit 58e7b1d5 upstream. With some devices, transfer hangs during I2C frame transmission. This issue disappears when reducing the internal frequency of the TWI IP. Even if it is indicated that internal clock max frequency is 66MHz, it seems we have oversampling on I2C signals making TWI believe that a transfer in progress is done. This fix has no impact on the I2C bus frequency. Signed-off-by:
Ludovic Desroches <ludovic.desroches@atmel.com> Acked-by:
Wolfram Sang <wsa@the-dreams.de> Acked-by:
Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com> Signed-off-by:
Nicolas Ferre <nicolas.ferre@atmel.com> Signed-off-by:
Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Aaro Koskinen authored
commit c37dd677 upstream. When booting Nokia N900 smartphone with v3.12 + omap2plus_defconfig (LOCKDEP enabled) and CONFIG_DISPLAY_PANEL_SONY_ACX565AKM enabled, the following BUG is seen during the boot: [ 7.302154] ===================================== [ 7.307128] [ BUG: bad unlock balance detected! ] [ 7.312103] 3.12.0-los.git-2093492-00120-g5e01dc7b #3 Not tainted [ 7.318450] ------------------------------------- [ 7.323425] kworker/u2:1/12 is trying to release lock (&ddata->mutex) at: [ 7.330657] [<c031b760>] acx565akm_enable+0x12c/0x18c [ 7.335998] but there are no more locks to release! Fix by removing double unlock and handling the locking completely inside acx565akm_panel_power_on() when doing the power on. Reported-by:
Eduardo Valentin <eduardo.valentin@ti.com> Signed-off-by:
Aaro Koskinen <aaro.koskinen@iki.fi> Signed-off-by:
Tomi Valkeinen <tomi.valkeinen@ti.com> Signed-off-by:
-
Balaji T K authored
commit 2ba2866f upstream. pin mux wl12xx_gpio and wl12xx_pins should be part of omap4_pmx_core and not omap4_pmx_wkup. So, move wl12xx_* to omap4_pmx_core. Fix the following error message: pinctrl-single 4a31e040.pinmux: mux offset out of range: 0x38 (0x38) pinctrl-single 4a31e040.pinmux: could not add functions for pinmux_wl12xx_pins 56x SDIO card is not detected after moving pin mux to omap4_pmx_core since sdmmc5_clk pull is disabled. Enable Pull up on sdmmc5_clk to detect SDIO card. This fixes a regression where WLAN did not work after a warm reset or after one up/down cycle that happened when we move omap4 to boot using device tree only. For reference, the kernel bug is described at: https://bugzilla.kernel.org/show_bug.cgi?id=63821Signed-off-by:
Balaji T K <balajitk@ti.com> [tony@atomide.com: update comments to describe the regression] Signed-off-by:
Tony Lindgren <tony@atomide.com> Signed-off-by:
-
Olof Johansson authored
commit f39918ee upstream. Enable MMC/SD on the Broadcom mobile platforms, and increase the block minors from the default 8 to 16 (since the Broadcom board by default has root on the 8th partition). Signed-off-by:
Olof Johansson <olof@lixom.net> Signed-off-by:
-
Russell King authored
commit 67130c54 upstream. - The LEDs register is write-only: it can't be read-modify-written. - The LEDs are write-1-for-off not 0. - The check for the platform was inverted. Fixes: cf6856d6 ("ARM: mach-footbridge: retire custom LED code") Signed-off-by:
Russell King <rmk+kernel@arm.linux.org.uk> Signed-off-by:
-
Russell King authored
commit 43659222 upstream. It's no good setting vga_base after the VGA console has been initialised, because if we do that we get this: Unable to handle kernel paging request at virtual address 000b8000 pgd = c0004000 [000b8000] *pgd=07ffc831, *pte=00000000, *ppte=00000000 0Internal error: Oops: 5017 [#1] ARM Modules linked in: CPU: 0 PID: 0 Comm: swapper Not tainted 3.12.0+ #49 task: c03e2974 ti: c03d8000 task.ti: c03d8000 PC is at vgacon_startup+0x258/0x39c LR is at request_resource+0x10/0x1c pc : [<c01725d0>] lr : [<c0022b50>] psr: 60000053 sp : c03d9f68 ip : 000b8000 fp : c03d9f8c r10: 000055aa r9 : 4401a103 r8 : ffffaa55 r7 : c03e357c r6 : c051b460 r5 : 000000ff r4 : 000c0000 r3 : 000b8000 r2 : c03e0514 r1 : 00000000 r0 : c0304971 Flags: nZCv IRQs on FIQs off Mode SVC_32 ISA ARM Segment kernel which is an access to the 0xb8000 without the PCI offset required to make it work. Fixes: cc22b4c1 ("ARM: set vga memory base at run-time") Signed-off-by:
-
Russell King authored
commit d8aa712c upstream. Commit f6f91b0d (ARM: allow kuser helpers to be removed from the vector page) required two pages for the vectors code. Although the code setting up the initial page tables was updated, the code which allocates page tables for new processes wasn't, neither was the code which tears down the mappings. Fix this. Fixes: f6f91b0d ("ARM: allow kuser helpers to be removed from the vector page") Signed-off-by:
-
Tom Lendacky authored
commit fc019c71 upstream. When performing an asynchronous ablkcipher operation the authenc completion callback routine is invoked, but it does not locate and use the proper IV. The callback routine, crypto_authenc_encrypt_done, is updated to use the same method of calculating the address of the IV as is done in crypto_authenc_encrypt function which sets up the callback. Signed-off-by:
Tom Lendacky <thomas.lendacky@amd.com> Signed-off-by:
Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by:
-
Horia Geanta authored
commit 5638cabf upstream. There are cases when cryptlen can be zero in crypto_ccm_auth(): -encryptiom: input scatterlist length is zero (no plaintext) -decryption: input scatterlist contains only the mac plus the condition of having different source and destination buffers (or else scatterlist length = max(plaintext_len, ciphertext_len)). These are not handled correctly, leading to crashes like: root@p4080ds:~/crypto# insmod tcrypt.ko mode=45 ------------[ cut here ]------------ kernel BUG at crypto/scatterwalk.c:37! Oops: Exception in kernel mode, sig: 5 [#1] SMP NR_CPUS=8 P4080 DS Modules linked in: tcrypt(+) crc32c xts xcbc vmac pcbc ecb gcm ghash_generic gf128mul ccm ctr seqiv CPU: 3 PID: 1082 Comm: cryptomgr_test Not tainted 3.11.0 #14 task: ee12c5b0 ti: eecd0000 task.ti: eecd0000 NIP: c0204d98 LR: f9225848 CTR: c0204d80 REGS: eecd1b70 TRAP: 0700 Not tainted (3.11.0) MSR: 00029002 <CE,EE,ME> CR: 22044022 XER: 20000000 GPR00: f9225c94 eecd1c20 ee12c5b0 eecd1c28 ee879400 ee879400 00000000 ee607464 GPR08: 00000001 00000001 00000000 006b0000 c0204d80 00000000 00000002 c0698e20 GPR16: ee987000 ee895000 fffffff4 ee879500 00000100 eecd1d58 00000001 00000000 GPR24: ee879400 00000020 00000000 00000000 ee5b2800 ee607430 00000004 ee607460 NIP [c0204d98] scatterwalk_start+0x18/0x30 LR [f9225848] get_data_to_compute+0x28/0x2f0 [ccm] Call Trace: [eecd1c20] [f9225974] get_data_to_compute+0x154/0x2f0 [ccm] (unreliable) [eecd1c70] [f9225c94] crypto_ccm_auth+0x184/0x1d0 [ccm] [eecd1cb0] [f9225d40] crypto_ccm_encrypt+0x60/0x2d0 [ccm] [eecd1cf0] [c020d77c] __test_aead+0x3ec/0xe20 [eecd1e20] [c020f35c] test_aead+0x6c/0xe0 [eecd1e40] [c020f420] alg_test_aead+0x50/0xd0 [eecd1e60] [c020e5e4] alg_test+0x114/0x2e0 [eecd1ee0] [c020bd1c] cryptomgr_test+0x4c/0x60 [eecd1ef0] [c0047058] kthread+0xa8/0xb0 [eecd1f40] [c000eb0c] ret_from_kernel_thread+0x5c/0x64 Instruction dump: 0f080000 81290024 552807fe 0f080000 5529003a 4bffffb4 90830000 39400000 39000001 8124000c 2f890000 7d28579e <0f090000> 81240008 91230004 4e800020 ---[ end trace 6d652dfcd1be37bd ]--- Cc: Jussi Kivilinna <jussi.kivilinna@mbnet.fi> Signed-off-by:
Horia Geanta <horia.geanta@freescale.com> Signed-off-by:
-
Tom Lendacky authored
commit 41da8b5a upstream. The scatterwalk_crypto_chain function invokes the scatterwalk_sg_chain function to chain two scatterlists, but the chain pointer indication bit is not set. When the resulting scatterlist is used, for example, by sg_nents to count the number of scatterlist entries, a segfault occurs because sg_nents does not follow the chain pointer to the chained scatterlist. Update scatterwalk_sg_chain to set the chain pointer indication bit as is done by the sg_chain function. Signed-off-by:
-
Gerald Schaefer authored
commit 9dda2769 upstream. Some s390 crypto algorithms incorrectly use the crypto_tfm structure to store private data. As the tfm can be shared among multiple threads, this can result in data corruption. This patch fixes aes-xts by moving the xts and pcc parameter blocks from the tfm onto the stack (48 + 96 bytes). Signed-off-by:
Gerald Schaefer <gerald.schaefer@de.ibm.com> Signed-off-by:
-
David Henningsson authored
commit eb82594b upstream. This machine also has mono output if run through DAC node 0x03. BugLink: https://bugs.launchpad.net/bugs/1256212Tested-by:
David Chen <david.chen@canonical.com> Signed-off-by:
David Henningsson <david.henningsson@canonical.com> Signed-off-by:
Takashi Iwai <tiwai@suse.de> Signed-off-by:
-
Takashi Iwai authored
commit 0756f09c upstream. MacBook Air 2,1 has a fairly different pin assignment from its brother MBA 1,1, and yet another quirks are needed for pin 0x18 and 0x19, similarly like what iMac 9,1 requires, in order to make the sound working on it. Reported-and-tested-by:
Bruno Prémont <bonbons@linux-vserver.org> Signed-off-by:
-
Takashi Iwai authored
commit 1cd9b2f7 upstream. It seems that EAPD on NID 0x16 is the only control over all outputs on HP machines with AD1984A while turning EAPD on NID 0x12 breaks the output. Thus we need to avoid fiddling EAPD on NID. As a quick workaround, just set own_eapd_ctrl flag for the wrong EAPD, then implement finer EAPD controls. Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=66321Signed-off-by:
-
David Henningsson authored
commit d59915d0 upstream. By trial and error, I found this patch could work around an issue where the headset mic would stop working if you switch between the internal mic and the headset mic, and the internal mic was muted. It still takes a second or two before the headset mic actually starts working, but still better than nothing. Information update from Kailang: The verb was ADC digital mute(bit 6 default 1). Switch internal mic and headset mic will run alc_headset_mode_default. The coef index 0x11 will set to 0x0041. Because headset mode was fixed type. It doesn't need to run alc_determine_headset_type. So, the value still keep 0x0041. ADC was muted. BugLink: https://bugs.launchpad.net/bugs/1256840Signed-off-by:
-
Takashi Iwai authored
commit b3bd4fc3 upstream. It seems that AD1986A cannot manage the dynamic pin on/off for auto-muting, but rather gets confused. Since each output has own amp, let's use it instead. Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=64971Signed-off-by:
-
Takashi Iwai authored
commit e7ca237b upstream. ASUS Z35HL laptop also needs the very same fix as the previous one that was applied to ASUS W7J. Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=66231Signed-off-by:
-
Takashi Iwai authored
commit 6ddf0fd1 upstream. The recent kernels got regressions on ASUS W7J with ALC660 codec where no sound comes out. After a long debugging session, we found out that setting the pin control on the unused NID 0x10 is mandatory for the outputs. And, it was found out that another magic of NID 0x0f that is required for other ASUS laptops isn't needed on this machine. Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=66081Reported-and-tested-by:
Andrey Lipaev <lipaev@mail.ru> Signed-off-by:
-
- 08 Dec, 2013 22 commits
-
-
Greg Kroah-Hartman authored
-
Pierre Ossman authored
commit 3e71985f upstream. The values were taken from the HDMI spec, but they assumed exact x/1.001 clocks. Since we round the clocks, we also need to calculate different N and CTS values. Note that the N for 25.2/1.001 MHz at 44.1 kHz audio is out of spec. Hopefully this mode is rarely used and/or HDMI sinks tolerate overly large values of N. bug: https://bugs.freedesktop.org/show_bug.cgi?id=69675Signed-off-by:
Pierre Ossman <pierre@ossman.eu> Signed-off-by:
Alex Deucher <alexander.deucher@amd.com> Cc: Josh Boyer <jwboyer@fedoraproject.org> Signed-off-by:
-
Pierre Ossman authored
commit a2098250 upstream. In order to have any realistic chance of calculating proper ACR values, we need to be able to calculate both N and CTS, not just CTS. We still aim for the ideal N as specified in the HDMI spec though. bug: https://bugs.freedesktop.org/show_bug.cgi?id=69675Signed-off-by:
-
Gu Zheng authored
commit d1b94327 upstream. Clean up the aio ring file in the fail path of aio_setup_ring and ioctx_alloc. And maybe it can fix the GPF issue reported by Dave Jones: https://lkml.org/lkml/2013/11/25/898Signed-off-by:
Gu Zheng <guz.fnst@cn.fujitsu.com> Signed-off-by:
Benjamin LaHaise <bcrl@kvack.org> Signed-off-by:
-
Sasha Levin authored
commit ddb8c45b upstream. After freeing ring_pages we leave it as is causing a dangling pointer. This has already caused an issue so to help catching any issues in the future NULL it out. Signed-off-by:
Sasha Levin <sasha.levin@oracle.com> Signed-off-by:
-
Sasha Levin authored
commit d5580232 upstream. ioctx_alloc() calls aio_setup_ring() to allocate a ring. If aio_setup_ring() fails to do so it would call aio_free_ring() before returning, but ioctx_alloc() would call aio_free_ring() again causing a double free of the ring. This is easily reproducible from userspace. Signed-off-by:
-
Dan Carpenter authored
commit 7f62656b upstream. alloc_anon_inode() returns an ERR_PTR(), it doesn't return NULL. Fixes: 71ad7490 ('rework aio migrate pages to use aio fs') Signed-off-by:
Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by:
Al Viro <viro@zeniv.linux.org.uk> Signed-off-by:
-
Benjamin LaHaise authored
commit 71ad7490 upstream. Don't abuse anon_inodes.c to host private files needed by aio; we can bloody well declare a mini-fs of our own instead of patching up what anon_inodes can create for us. Tested-by:
-
Al Viro authored
commit 6987843f upstream. Signed-off-by:
-
Kent Overstreet authored
commit e34ecee2 upstream. aio kiocb refcounting was broken - it was relying on keeping track of the number of available ring buffer entries, which it needs to do anyways; then at shutdown time it'd wait for completions to be delivered until the # of available ring buffer entries equalled what it was initialized to. Problem with that is that the ring buffer is mapped writable into userspace, so userspace could futz with the head and tail pointers to cause the kernel to see extra completions, and cause free_ioctx() to return while there were still outstanding kiocbs. Which would be bad. Fix is just to directly refcount the kiocbs - which is more straightforward, and with the new percpu refcounting code doesn't cost us any cacheline bouncing which was the whole point of the original scheme. Also clean up ioctx_alloc()'s error path and fix a bug where it wasn't subtracting from aio_nr if ioctx_add_table() failed. Signed-off-by:
Kent Overstreet <kmo@daterainc.com> Cc: Benjamin LaHaise <bcrl@kvack.org> Signed-off-by:
-
Miroslav Lichvar authored
commit a97ad0c4 upstream. The current code requires that the scheduled update of the RTC happens in the closest tick to the half of the second. This seems to be difficult to achieve reliably. The scheduled work may be missing the target time by a tick or two and be constantly rescheduled every second. Relax the limit to 10 ticks. As a typical RTC drifts in the 11-minute update interval by several milliseconds, this shouldn't affect the overall accuracy of the RTC much. Signed-off-by:
Miroslav Lichvar <mlichvar@redhat.com> Signed-off-by:
John Stultz <john.stultz@linaro.org> Cc: Josh Boyer <jwboyer@fedoraproject.org> Signed-off-by:
-
Tomoki Sekiyama authored
commit 7c8a3679 upstream. Add locking of q->sysfs_lock into elevator_change() (an exported function) to ensure it is held to protect q->elevator from elevator_init(), even if elevator_change() is called from non-sysfs paths. sysfs path (elv_iosched_store) uses __elevator_change(), non-locking version, as the lock is already taken by elv_iosched_store(). Signed-off-by:
Tomoki Sekiyama <tomoki.sekiyama@hds.com> Signed-off-by:
Jens Axboe <axboe@kernel.dk> Cc: Josh Boyer <jwboyer@fedoraproject.org> Signed-off-by:
-
Tomoki Sekiyama authored
commit eb1c160b upstream. The soft lockup below happens at the boot time of the system using dm multipath and the udev rules to switch scheduler. [ 356.127001] BUG: soft lockup - CPU#3 stuck for 22s! [sh:483] [ 356.127001] RIP: 0010:[<ffffffff81072a7d>] [<ffffffff81072a7d>] lock_timer_base.isra.35+0x1d/0x50 ... [ 356.127001] Call Trace: [ 356.127001] [<ffffffff81073810>] try_to_del_timer_sync+0x20/0x70 [ 356.127001] [<ffffffff8118b08a>] ? kmem_cache_alloc_node_trace+0x20a/0x230 [ 356.127001] [<ffffffff810738b2>] del_timer_sync+0x52/0x60 [ 356.127001] [<ffffffff812ece22>] cfq_exit_queue+0x32/0xf0 [ 356.127001] [<ffffffff812c98df>] elevator_exit+0x2f/0x50 [ 356.127001] [<ffffffff812c9f21>] elevator_change+0xf1/0x1c0 [ 356.127001] [<ffffffff812caa50>] elv_iosched_store+0x20/0x50 [ 356.127001] [<ffffffff812d1d09>] queue_attr_store+0x59/0xb0 [ 356.127001] [<ffffffff812143f6>] sysfs_write_file+0xc6/0x140 [ 356.127001] [<ffffffff811a326d>] vfs_write+0xbd/0x1e0 [ 356.127001] [<ffffffff811a3ca9>] SyS_write+0x49/0xa0 [ 356.127001] [<ffffffff8164e899>] system_call_fastpath+0x16/0x1b This is caused by a race between md device initialization by multipathd and shell script to switch the scheduler using sysfs. - multipathd: SyS_ioctl -> do_vfs_ioctl -> dm_ctl_ioctl -> ctl_ioctl -> table_load -> dm_setup_md_queue -> blk_init_allocated_queue -> elevator_init q->elevator = elevator_alloc(q, e); // not yet initialized - sh -c 'echo deadline > /sys/$DEVPATH/queue/scheduler': elevator_switch (in the call trace above) struct elevator_queue *old = q->elevator; q->elevator = elevator_alloc(q, new_e); elevator_exit(old); // lockup! (*) - multipathd: (cont.) err = e->ops.elevator_init_fn(q); // init fails; q->elevator is modified (*) When del_timer_sync() is called, lock_timer_base() will loop infinitely while timer->base == NULL. In this case, as timer will never initialized, it results in lockup. This patch introduces acquisition of q->sysfs_lock around elevator_init() into blk_init_allocated_queue(), to provide mutual exclusion between initialization of the q->scheduler and switching of the scheduler. This should fix this bugzilla: https://bugzilla.redhat.com/show_bug.cgi?id=902012Signed-off-by:
-
Stanislaw Gruszka authored
commit 3b9b74ba upstream. Add support for new RF chip ID: 3070. It seems to be the same as 5370, maybe vendor just put wrong value on the eeprom, but add this id anyway since devices with it showed on the marked. Signed-off-by:
Stanislaw Gruszka <sgruszka@redhat.com> Signed-off-by:
John W. Linville <linville@tuxdriver.com> Signed-off-by:
-
Neil Horman authored
commit 05104a4e upstream. The warning for the irq remapping broken check in intel_irq_remapping.c is pretty pointless. We need the warning, but we know where its comming from, the stack trace will always be the same, and it needlessly triggers things like Abrt. This changes the warning to just print a text warning about BIOS being broken, without the stack trace, then sets the appropriate taint bit. Since we automatically disable irq remapping, theres no need to contiue making Abrt jump at this problem Signed-off-by:
Neil Horman <nhorman@tuxdriver.com> CC: Joerg Roedel <joro@8bytes.org> CC: Bjorn Helgaas <bhelgaas@google.com> CC: Andy Lutomirski <luto@amacapital.net> CC: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com> CC: Sebastian Andrzej Siewior <sebastian@breakpoint.cc> Signed-off-by:
Joerg Roedel <joro@8bytes.org> Signed-off-by:
-
Julian Stecklina authored
commit f9423606 upstream. The BUG_ON in drivers/iommu/intel-iommu.c:785 can be triggered from userspace via VFIO by calling the VFIO_IOMMU_MAP_DMA ioctl on a vfio device with any address beyond the addressing capabilities of the IOMMU. The problem is that the ioctl code calls iommu_iova_to_phys before it calls iommu_map. iommu_map handles the case that it gets addresses beyond the addressing capabilities of its IOMMU. intel_iommu_iova_to_phys does not. This patch fixes iommu_iova_to_phys to return NULL for addresses beyond what the IOMMU can handle. This in turn causes the ioctl call to fail in iommu_map and (correctly) return EFAULT to the user with a helpful warning message in the kernel log. Signed-off-by:
Julian Stecklina <jsteckli@os.inf.tu-dresden.de> Acked-by:
Alex Williamson <alex.williamson@redhat.com> Signed-off-by:
-
Oliver Neukum authored
commit 403cfb53 upstream. Some systems although they have firmware class 'M', which usually needs a work around to not crash, must not be subjected to the work around because the work around crashes them. They cannot be told apart by their own device descriptor, but as they are part of compound devices, can be identified by looking at their siblings. Signed-off-by:
Oliver Neukum <oneukum@suse.de> Signed-off-by:
Jiri Kosina <jkosina@suse.cz> Signed-off-by:
-
Simon Wood authored
commit 348cbaa8 upstream. By default the Logitech MOMO Force (Black) presents a combined accel/brake axis ('Y'). This patch modifies the HID descriptor to present seperate accel/brake axes ('Y' and 'Z'). Signed-off-by:
Simon Wood <simon@mungewell.org> Signed-off-by:
-
Sasha Levin authored
commit 2ab68ec9 upstream. kyro would copy u32s and specify sizeof(unsigned long) as the size to copy. This would copy more data than intended and cause memory corruption and might leak kernel memory. Signed-off-by:
-
Thomas Pugliese authored
commit f74b75e7 upstream. change WA_SEGS_MAX to a number that is legal according to the WUSB spec. Signed-off-by:
Thomas Pugliese <thomas.pugliese@gmail.com> Signed-off-by:
-
Sergei Shtylyov authored
commit ea78201e upstream. After commit 09fc7d22 (usb: musb: fix incorrect usage of resource pointer), CPPI DMA driver on DaVinci DM6467 can't detect its dedicated IRQ and so the MUSB IRQ is erroneously used instead. This is because only 2 resources are passed to the MUSB driver from the DaVinci glue layer, so fix this by always copying 3 resources (it's safe since a placeholder for the 3rd resource is always there) and passing 'pdev->num_resources' instead of the size of musb_resources[] to platform_device_add_resources(). Signed-off-by:
Sergei Shtylyov <sergei.shtylyov@cogentembedded.com> Signed-off-by:
Felipe Balbi <balbi@ti.com> Signed-off-by:
-
majianpeng authored
commit 60aaf933 upstream. and commit 0c775d52 When we change group_thread_cnt from sysfs entry, it can OOPS. The kernel messages are: [ 135.299021] BUG: unable to handle kernel NULL pointer dereference at (null) [ 135.299073] IP: [<ffffffff815188ab>] handle_active_stripes+0x32b/0x440 [ 135.299107] PGD 0 [ 135.299122] Oops: 0000 [#1] SMP [ 135.299144] Modules linked in: netconsole e1000e ptp pps_core [ 135.299188] CPU: 3 PID: 2225 Comm: md0_raid5 Not tainted 3.12.0+ #24 [ 135.299214] Hardware name: To Be Filled By O.E.M. To Be Filled By O.E.M./To be filled by O.E.M., BIOS 080015 11/09/2011 [ 135.299255] task: ffff8800b9638f80 ti: ffff8800b77a4000 task.ti: ffff8800b77a4000 [ 135.299283] RIP: 0010:[<ffffffff815188ab>] [<ffffffff815188ab>] handle_active_stripes+0x32b/0x440 [ 135.299323] RSP: 0018:ffff8800b77a5c48 EFLAGS: 00010002 [ 135.299344] RAX: ffff880037bb5c70 RBX: 0000000000000000 RCX: 0000000000000008 [ 135.299371] RDX: ffff880037bb5cb8 RSI: 0000000000000001 RDI: ffff880037bb5c00 [ 135.299398] RBP: ffff8800b77a5d08 R08: 0000000000000001 R09: 0000000000000000 [ 135.299425] R10: ffff8800b77a5c98 R11: 00000000ffffffff R12: ffff880037bb5c00 [ 135.299452] R13: 0000000000000000 R14: 0000000000000000 R15: ffff880037bb5c70 [ 135.299479] FS: 0000000000000000(0000) GS:ffff88013fd80000(0000) knlGS:0000000000000000 [ 135.299510] CS: 0010 DS: 0000 ES: 0000 CR0: 000000008005003b [ 135.299532] CR2: 0000000000000000 CR3: 0000000001c0b000 CR4: 00000000000407e0 [ 135.299559] Stack: [ 135.299570] ffff8800b77a5c88 ffffffff8107383e ffff8800b77a5c88 ffff880037a64300 [ 135.299611] 000000000000ec08 ffff880037bb5cb8 ffff8800b77a5c98 ffffffffffffffd8 [ 135.299654] 000000000000ec08 ffff880037bb5c60 ffff8800b77a5c98 ffff8800b77a5c98 [ 135.299696] Call Trace: [ 135.299711] [<ffffffff8107383e>] ? __wake_up+0x4e/0x70 [ 135.299733] [<ffffffff81518f88>] raid5d+0x4c8/0x680 [ 135.299756] [<ffffffff817174ed>] ? schedule_timeout+0x15d/0x1f0 [ 135.299781] [<ffffffff81524c9f>] md_thread+0x11f/0x170 [ 135.299804] [<ffffffff81069cd0>] ? wake_up_bit+0x40/0x40 [ 135.299826] [<ffffffff81524b80>] ? md_rdev_init+0x110/0x110 [ 135.299850] [<ffffffff81069656>] kthread+0xc6/0xd0 [ 135.299871] [<ffffffff81069590>] ? kthread_freezable_should_stop+0x70/0x70 [ 135.299899] [<ffffffff81722ffc>] ret_from_fork+0x7c/0xb0 [ 135.299923] [<ffffffff81069590>] ? kthread_freezable_should_stop+0x70/0x70 [ 135.299951] Code: ff ff ff 0f 84 d7 fe ff ff e9 5c fe ff ff 66 90 41 8b b4 24 d8 01 00 00 45 31 ed 85 f6 0f 8e 7b fd ff ff 49 8b 9c 24 d0 01 00 00 <48> 3b 1b 49 89 dd 0f 85 67 fd ff ff 48 8d 43 28 31 d2 eb 17 90 [ 135.300005] RIP [<ffffffff815188ab>] handle_active_stripes+0x32b/0x440 [ 135.300005] RSP <ffff8800b77a5c48> [ 135.300005] CR2: 0000000000000000 [ 135.300005] ---[ end trace 504854e5bb7562ed ]--- [ 135.300005] Kernel panic - not syncing: Fatal exception This is because raid5d() can be running when the multi-thread resources are changed via system. We see need to provide locking. mddev->device_lock is suitable, but we cannot simple call alloc_thread_groups under this lock as we cannot allocate memory while holding a spinlock. So change alloc_thread_groups() to allocate and return the data structures, then raid5_store_group_thread_cnt() can take the lock while updating the pointers to the data structures. This fixes a bug introduced in 3.12 and so is suitable for the 3.12.x stable series. Fixes: b721420eSigned-off-by:
Jianpeng Ma <majianpeng@gmail.com> Signed-off-by:
NeilBrown <neilb@suse.de> Reviewed-by:
Shaohua Li <shli@kernel.org> Signed-off-by:
-
