- 06 Mar, 2015 40 commits
-
-
Malcolm Priestley authored
commit cfcd7b82 upstream. Ocassionally the device fails to report back an interrupt urb status which results in false no lock trigger on the RS2000 demodulator. Increase time from 60 msecs to 200 msecs. Signed-off-by:
Malcolm Priestley <tvboxspy@gmail.com> Signed-off-by:
Mauro Carvalho Chehab <mchehab@osg.samsung.com> Signed-off-by:
Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Mika Westerberg authored
commit 3095794a upstream. On some Braswell systems BIOS leaves resets for SPI host controllers active. This prevents the SPI driver from transferring messages on wire. Fix this in similar way that we do for I2C already by deasserting resets for the SPI host controllers. Reported-by:
Yang A Fang <yang.a.fang@intel.com> Signed-off-by:
Mika Westerberg <mika.westerberg@linux.intel.com> Signed-off-by:
Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by:
-
Mika Westerberg authored
commit 3293c7b8 upstream. On Baytrail and Braswell the BIOS might leave the I2C host controllers enabled, probably because it uses them for its own purposes. This is fine in normal cases because the I2C driver will disable the hardware when it is probed anyway. However, in case of suspend to disk it is different story. If the driver happens to be compiled as a module the boot kernel never loads the driver thus leaving host controllers enabled upon loading the hibernation image. The I2C host controller interrupt mask register has default value of 0x8ff, in other words it has most of the interrupts unmasked. When combined with the fact that the host controller is enabled, the driver immediately starts getting interrupts even before its resume hook is called (once IO-APIC is resumed). Since the driver is not prepared for this it will crash the kernel due to NULL pointer derefence because dev->msgs is NULL. Unfortunately we were not able to get full backtrace to from the console which could be reproduced here. In order to fix this even when the driver is compiled as module, we disable the I2C host controllers in byt_i2c_setup() before devices are created. Reported-by:
Yu Chen <yu.c.chen@intel.com> Signed-off-by:
-
Juergen Gross authored
commit facb5732 upstream. A request in the ring buffer mustn't be read after it has been marked as consumed. Otherwise it might already have been reused by the frontend without violating the ring protocol. To avoid inconsistencies in the backend only work on a private copy of the request. This will ensure a malicious guest not being able to bypass consistency checks of the backend by modifying an active request. Signed-off-by:
Juergen Gross <jgross@suse.com> Signed-off-by:
David Vrabel <david.vrabel@citrix.com> Signed-off-by:
-
Ross Lagerwall authored
commit 72978b2f upstream. Commit 61a734d3 ("xen/manage: Always freeze/thaw processes when suspend/resuming") ensured that userspace processes were always frozen before suspending to reduce interaction issues when resuming devices. However, freeze_processes() does not freeze kernel threads. Freeze kernel threads as well to prevent deadlocks with the khubd thread when resuming devices. This is what native suspend and resume does. Example deadlock: [ 7279.648010] [<ffffffff81446bde>] ? xen_poll_irq_timeout+0x3e/0x50 [ 7279.648010] [<ffffffff81448d60>] xen_poll_irq+0x10/0x20 [ 7279.648010] [<ffffffff81011723>] xen_lock_spinning+0xb3/0x120 [ 7279.648010] [<ffffffff810115d1>] __raw_callee_save_xen_lock_spinning+0x11/0x20 [ 7279.648010] [<ffffffff815620b6>] ? usb_control_msg+0xe6/0x120 [ 7279.648010] [<ffffffff81747e50>] ? _raw_spin_lock_irq+0x50/0x60 [ 7279.648010] [<ffffffff8174522c>] wait_for_completion+0xac/0x160 [ 7279.648010] [<ffffffff8109c520>] ? try_to_wake_up+0x2c0/0x2c0 [ 7279.648010] [<ffffffff814b60f2>] dpm_wait+0x32/0x40 [ 7279.648010] [<ffffffff814b6eb0>] device_resume+0x90/0x210 [ 7279.648010] [<ffffffff814b7d71>] dpm_resume+0x121/0x250 [ 7279.648010] [<ffffffff8144c570>] ? xenbus_dev_request_and_reply+0xc0/0xc0 [ 7279.648010] [<ffffffff814b80d5>] dpm_resume_end+0x15/0x30 [ 7279.648010] [<ffffffff81449fba>] do_suspend+0x10a/0x200 [ 7279.648010] [<ffffffff8144a2f0>] ? xen_pre_suspend+0x20/0x20 [ 7279.648010] [<ffffffff8144a1d0>] shutdown_handler+0x120/0x150 [ 7279.648010] [<ffffffff8144c60f>] xenwatch_thread+0x9f/0x160 [ 7279.648010] [<ffffffff810ac510>] ? finish_wait+0x80/0x80 [ 7279.648010] [<ffffffff8108d189>] kthread+0xc9/0xe0 [ 7279.648010] [<ffffffff8108d0c0>] ? flush_kthread_worker+0x80/0x80 [ 7279.648010] [<ffffffff8175087c>] ret_from_fork+0x7c/0xb0 [ 7279.648010] [<ffffffff8108d0c0>] ? flush_kthread_worker+0x80/0x80 [ 7441.216287] INFO: task khubd:89 blocked for more than 120 seconds. [ 7441.219457] Tainted: G X 3.13.11-ckt12.kz #1 [ 7441.222176] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message. [ 7441.225827] khubd D ffff88003f433440 0 89 2 0x00000000 [ 7441.229258] ffff88003ceb9b98 0000000000000046 ffff88003ce83000 0000000000013440 [ 7441.232959] ffff88003ceb9fd8 0000000000013440 ffff88003cd13000 ffff88003ce83000 [ 7441.236658] 0000000000000286 ffff88003d3e0000 ffff88003ceb9bd0 00000001001aa01e [ 7441.240415] Call Trace: [ 7441.241614] [<ffffffff817442f9>] schedule+0x29/0x70 [ 7441.243930] [<ffffffff81743406>] schedule_timeout+0x166/0x2c0 [ 7441.246681] [<ffffffff81075b80>] ? call_timer_fn+0x110/0x110 [ 7441.249339] [<ffffffff8174357e>] schedule_timeout_uninterruptible+0x1e/0x20 [ 7441.252644] [<ffffffff81077710>] msleep+0x20/0x30 [ 7441.254812] [<ffffffff81555f00>] hub_port_reset+0xf0/0x580 [ 7441.257400] [<ffffffff81558465>] hub_port_init+0x75/0xb40 [ 7441.259981] [<ffffffff814bb3c9>] ? update_autosuspend+0x39/0x60 [ 7441.262817] [<ffffffff814bb4f0>] ? pm_runtime_set_autosuspend_delay+0x50/0xa0 [ 7441.266212] [<ffffffff8155a64a>] hub_thread+0x71a/0x1750 [ 7441.268728] [<ffffffff810ac510>] ? finish_wait+0x80/0x80 [ 7441.271272] [<ffffffff81559f30>] ? usb_port_resume+0x670/0x670 [ 7441.274067] [<ffffffff8108d189>] kthread+0xc9/0xe0 [ 7441.276305] [<ffffffff8108d0c0>] ? flush_kthread_worker+0x80/0x80 [ 7441.279131] [<ffffffff8175087c>] ret_from_fork+0x7c/0xb0 [ 7441.281659] [<ffffffff8108d0c0>] ? flush_kthread_worker+0x80/0x80 Signed-off-by:
Ross Lagerwall <ross.lagerwall@citrix.com> Signed-off-by:
-
Arnd Bergmann authored
commit 67fadaa2 upstream. Commit 32726d2d ("ARM: SAMSUNG: Remove legacy clock code") already removed the callback pointer, but there was one remaining user: drivers/cpufreq/s3c24xx-cpufreq.c: In function 's3c_cpufreq_resume_clocks': drivers/cpufreq/s3c24xx-cpufreq.c:149:14: error: 'struct s3c_cpufreq_info' has no member named 'resume_clocks' cpu_cur.info->resume_clocks(); ^ Signed-off-by:
Arnd Bergmann <arnd@arndb.de> Fixes: 32726d2d ("ARM: SAMSUNG: Remove legacy clock code") Acked-by:
Viresh Kumar <viresh.kumar@linaro.org> Signed-off-by:
-
Arnd Bergmann authored
commit 61882b63 upstream. The two functions s3c2416_cpufreq_driver_init and s3c_cpufreq_register are marked init but are called from a context that might be run after the __init sections are discarded, as the compiler points out: WARNING: vmlinux.o(.data+0x1ad9dc): Section mismatch in reference from the variable s3c2416_cpufreq_driver to the function .init.text:s3c2416_cpufreq_driver_init() WARNING: drivers/built-in.o(.text+0x35b5dc): Section mismatch in reference from the function s3c2410a_cpufreq_add() to the function .init.text:s3c_cpufreq_register() This removes the __init markings. Signed-off-by:
-
Mikulas Patocka authored
commit d4d4eda2 upstream. On Dell Latitude C600 laptop with Pentium 3 850MHz processor, the speedstep-smi driver sometimes loads and sometimes doesn't load with "change to state X failed" message. The hardware sometimes refuses to change frequency and in this case, we need to retry later. I found out that we need to enable interrupts while waiting. When we enable interrupts, the hardware blockage that prevents frequency transition resolves and the transition is possible. With disabled interrupts, the blockage doesn't resolve (no matter how long do we wait). The exact reasons for this hardware behavior are unknown. This patch enables interrupts in the function speedstep_set_state that can be called with disabled interrupts. However, this function is called with disabled interrupts only from speedstep_get_freqs, so it shouldn't cause any problem. Signed-off-by: Mikulas Patocka <mpatocka@redhat.com Acked-by:
-
Viresh Kumar authored
commit 6ffae8c0 upstream. In __cpufreq_remove_dev_finish(), per-cpu 'cpufreq_cpu_data' needs to be cleared before calling kobject_put(&policy->kobj) and under cpufreq_driver_lock. Otherwise, if someone else calls cpufreq_cpu_get() in parallel with it, they can obtain a non-NULL policy from that after kobject_put(&policy->kobj) was executed. Consider this case: Thread A Thread B cpufreq_cpu_get() acquire cpufreq_driver_lock read-per-cpu cpufreq_cpu_data kobject_put(&policy->kobj); kobject_get(&policy->kobj); ... per_cpu(&cpufreq_cpu_data, cpu) = NULL And this will result in a warning like this one: ------------[ cut here ]------------ WARNING: CPU: 0 PID: 4 at include/linux/kref.h:47 kobject_get+0x41/0x50() Modules linked in: acpi_cpufreq(+) nfsd auth_rpcgss nfs_acl lockd grace sunrpc xfs libcrc32c sd_mod ixgbe igb mdio ahci hwmon ... Call Trace: [<ffffffff81661b14>] dump_stack+0x46/0x58 [<ffffffff81072b61>] warn_slowpath_common+0x81/0xa0 [<ffffffff81072c7a>] warn_slowpath_null+0x1a/0x20 [<ffffffff812e16d1>] kobject_get+0x41/0x50 [<ffffffff815262a5>] cpufreq_cpu_get+0x75/0xc0 [<ffffffff81527c3e>] cpufreq_update_policy+0x2e/0x1f0 [<ffffffff810b8cb2>] ? up+0x32/0x50 [<ffffffff81381aa9>] ? acpi_ns_get_node+0xcb/0xf2 [<ffffffff81381efd>] ? acpi_evaluate_object+0x22c/0x252 [<ffffffff813824f6>] ? acpi_get_handle+0x95/0xc0 [<ffffffff81360967>] ? acpi_has_method+0x25/0x40 [<ffffffff81391e08>] acpi_processor_ppc_has_changed+0x77/0x82 [<ffffffff81089566>] ? move_linked_works+0x66/0x90 [<ffffffff8138e8ed>] acpi_processor_notify+0x58/0xe7 [<ffffffff8137410c>] acpi_ev_notify_dispatch+0x44/0x5c [<ffffffff8135f293>] acpi_os_execute_deferred+0x15/0x22 [<ffffffff8108c910>] process_one_work+0x160/0x410 [<ffffffff8108d05b>] worker_thread+0x11b/0x520 [<ffffffff8108cf40>] ? rescuer_thread+0x380/0x380 [<ffffffff81092421>] kthread+0xe1/0x100 [<ffffffff81092340>] ? kthread_create_on_node+0x1b0/0x1b0 [<ffffffff81669ebc>] ret_from_fork+0x7c/0xb0 [<ffffffff81092340>] ? kthread_create_on_node+0x1b0/0x1b0 ---[ end trace 89e66eb9795efdf7 ]--- The actual code flow is as follows: Thread A: Workqueue: kacpi_notify acpi_processor_notify() acpi_processor_ppc_has_changed() cpufreq_update_policy() cpufreq_cpu_get() kobject_get() Thread B: xenbus_thread() xenbus_thread() msg->u.watch.handle->callback() handle_vcpu_hotplug_event() vcpu_hotplug() cpu_down() __cpu_notify(CPU_POST_DEAD..) cpufreq_cpu_callback() __cpufreq_remove_dev_finish() cpufreq_policy_put_kobj() kobject_put() cpufreq_cpu_get() gets the policy from per-cpu variable cpufreq_cpu_data under cpufreq_driver_lock, and once it gets a valid policy it expects it to not be freed until cpufreq_cpu_put() is called. But the race happens when another thread puts the kobject first and updates cpufreq_cpu_data before or later. And so the first thread gets a valid policy structure and before it does kobject_get() on it, the second one has already done kobject_put(). Fix this by setting cpufreq_cpu_data to NULL before putting the kobject and that too under locks. Reported-by:
Ethan Zhao <ethan.zhao@oracle.com> Reported-by:
Santosh Shilimkar <santosh.shilimkar@oracle.com> Signed-off-by:
-
Larry Finger authored
commit aeb2d2a4 upstream. In commit e9538cf4 ("rtlwifi: Fix error when accessing unmapped memory in skb"), a printk was included to indicate that the condition had been reached. There is now enough evidence from other users that the fix is working. That logging statement can now be removed. Signed-off-by:
Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by:
Kalle Valo <kvalo@codeaurora.org> Signed-off-by:
-
Larry Finger authored
commit 6d4beca3 upstream. This driver utilizes a FIFO buffer for RX descriptors. There are four places in the code where it calculates the number of free slots. Several of those locations do the calculation incorrectly. To fix these and to prevent future mistakes, a common inline routine is created. Signed-off-by:
-
Troy Tan authored
commit 21b39ddb upstream. There are instances where the DMA engine stalls. The new code detects such stalls and restarts DMA without needing a power reset. Signed-off-by:
Troy Tan <troy_tan@realsil.com.cn> Signed-off-by:
-
Troy Tan authored
commit 92ff7542 upstream. The firmware supplies two kinds of packets via the RX mechanism. Besides the normal data received over the air, these packets may contain bluetooth status and other information. The present code fails to detect which kind of information was received. Signed-off-by:
-
Troy Tan authored
commit 6e5f4436 upstream. Initially, the routine to update the write point in the FIFO buffer was coded to save CPU time by not doing the calculation every interrupt. This was an error and results in TX hangs. Signed-off-by:
-
Troy Tan authored
commit b661a5da upstream. When the buffer descriptor index exceeds 2, then a TX HANG condition will result. Signed-off-by:
-
Arnd Bergmann authored
commit f9a7ba32 upstream. An earlier bug fix of mine made the SND_DM365_VOICE_CODEC symbol tristate to avoid creating an undefined reference from the davinci-vcif.c driver to the davinci_soc_platform_register function that may be in a module. However, this may now lead to a different error on randconfig kernels: "warning: SND_DM365_VOICE_CODEC creates inconsistent choice state" This happens because we now have a choice statement with one bool and one tristate option, and the latter might not support being set to 'y' because of dependencies. This new change turns the other option into 'tristate' as well, which avoids the problem. Signed-off-by:
Mark Brown <broonie@kernel.org> Signed-off-by:
-
Lars-Peter Clausen authored
commit 7331ea47 upstream. Commit f6b2a045 ("ASoC: pxa: mioa701_wm9713: Convert to table based DAPM setup") converted the driver to register the board level DAPM elements with the card's DAPM context rather than the CODEC's DAPM context. The change overlooked that the speaker widget event callback accesses the widget's codec field which is only valid if the widget has been registered in a CODEC DAPM context. This patch modifies the callback to take an alternative route to get the CODEC. Fixes: f6b2a045 ("ASoC: pxa: mioa701_wm9713: Convert to table based DAPM setup") Signed-off-by:
Lars-Peter Clausen <lars@metafoo.de> Signed-off-by:
-
Arnd Bergmann authored
commit 4c121129 upstream. The rt5677 codec has gained code that requires SPI to work correctly, but there is no provision in Kconfig to prevent the driver from being used when SPI is disabled or a loadable module, resulting in this build error: sound/built-in.o: In function `rt5677_spi_write': :(.text+0xa7ba0): undefined reference to `spi_sync' sound/built-in.o: In function `rt5677_spi_driver_init': :(.init.text+0x253c): undefined reference to `spi_register_driver' ERROR: "spi_sync" [sound/soc/codecs/snd-soc-rt5677-spi.ko] undefined! ERROR: "spi_register_driver" [sound/soc/codecs/snd-soc-rt5677-spi.ko] undefined! This makes the SPI portion of the driver depend on the SPI subsystem, and disables the function that uses SPI for firmware download if SPI is disabled. The latter may not be the correct solution, but I could not come up with a better one. Signed-off-by:
-
Christian Engelmayer authored
commit 279e17ae upstream. Function sst_acpi_probe() uses plain strcpy for setting member firmware_name of a struct intel_sst_drv from member firmware of a struct sst_machines. Thereby the destination array has got a length of 20 byte while the source may hold 32 byte. Since eg. commit 64b9c90b ("ASoC: Intel: Fix BYTCR firmware name") increased strings from "fw_sst_0f28.bin" to "intel/fw_sst_0f28.bin" there is an actual possibility that the 20 byte array at the end of struct intel_sst_drv is overrun. Thus increase the size of the destination and use the same define for both structs. Detected by Coverity CID 1260087. Signed-off-by:
Christian Engelmayer <cengelma@gmx.at> Signed-off-by:
-
Bard Liao authored
commit 92b133f2 upstream. RT5670 doesn't support auto incrementing writes so driver should set the use_single_rw flag for regmap. Signed-off-by:
Bard Liao <bardliao@realtek.com> Signed-off-by:
-
Michel Dänzer authored
commit 16b036af upstream. If the image size would ever read as 0, pci_get_rom_size() could keep processing the same image over and over again. Exit the loop if we ever read a length of zero. This fixes a soft lockup on boot when the radeon driver calls pci_get_rom_size() on an AMD Radeon R7 250X PCIe discrete graphics card. [bhelgaas: changelog, reference] Link: https://bugs.launchpad.net/ubuntu/+source/linux/+bug/1386973Reported-by:
Federico <federicotg@gmail.com> Signed-off-by:
Michel Dänzer <michel.daenzer@amd.com> Signed-off-by:
Bjorn Helgaas <bhelgaas@google.com> Reviewed-by:
Alex Deucher <alexander.deucher@amd.com> Signed-off-by:
-
Ricardo Ribalda Delgado authored
commit 145b3fe5 upstream. Some implementations of modprobe fail to load the driver for a PCI device automatically because the "interface" part of the modalias from the kernel is lowercase, and the modalias from file2alias is uppercase. The "interface" is the low-order byte of the Class Code, defined in PCI r3.0, Appendix D. Most interface types defined in the spec do not use alpha characters, so they won't be affected. For example, 00h, 01h, 10h, 20h, etc. are unaffected. Print the "interface" byte of the Class Code in uppercase hex, as we already do for the Vendor ID, Device ID, Class, etc. Commit 89ec3dcf ("PCI: Generate uppercase hex for modalias interface class") fixed only half of the problem. Some udev implementations rely on the uevent file and not the modalias file. Fixes: d1ded203 ("PCI: add MODALIAS to hotplug event for pci devices") Fixes: 89ec3dcf ("PCI: Generate uppercase hex for modalias interface class") Signed-off-by:
Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com> Signed-off-by:
-
Seth Forshee authored
commit 6d00f37e upstream. d1c7e29e (HID: i2c-hid: prevent buffer overflow in early IRQ) changed hid_get_input() to read ihid->bufsize bytes, which can be more than wMaxInputLength. This is the case with the Dell XPS 13 9343, and it is causing events to be missed. In some cases the missed events are releases, which can cause the cursor to jump or freeze, among other problems. Limit the number of bytes read to min(wMaxInputLength, ihid->bufsize) to prevent such problems. Fixes: d1c7e29e "HID: i2c-hid: prevent buffer overflow in early IRQ" Signed-off-by:
Seth Forshee <seth.forshee@canonical.com> Reviewed-by:
Benjamin Tissoires <benjamin.tissoires@redhat.com> Signed-off-by:
Jiri Kosina <jkosina@suse.cz> Signed-off-by:
-
Luciano Coelho authored
commit 5523d11c upstream. We don't really need to use different mac colors when adding mac contexts, because they're not used anywhere. In fact, the firmware doesn't accept 255 as a valid color, so we get into a SYSASSERT 0x3401 when we reach that. Remove the color increment to use always zero and avoid reaching 255. Signed-off-by:
Luciano Coelho <luciano.coelho@intel.com> Reviewed-by:
Johannes Berg <johannes.berg@intel.com> Signed-off-by:
Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by:
-
Luciano Coelho authored
commit fd66fc1c upstream. When iwl_mvm_power_update_mac() is called, we have already added the mac context, so if this call fails we should remove the mac. Fixes: commit e5e7aa8e ('iwlwifi: mvm: refactor power code') Signed-off-by:
-
Eyal Shapira authored
commit 2cee4762 upstream. These are coming from the FW and are used to access arrays. Bad values can cause an out of bounds access so discard such ba_notifs and warn. Signed-off-by:
Eyal Shapira <eyalx.shapira@intel.com> Signed-off-by:
-
Emmanuel Grumbach authored
commit cd8f4384 upstream. The base address of the scheduler in the device's memory (SRAM) comes from two different sources. The periphery register and the alive notification from the firmware. We have a check in iwl_pcie_tx_start that ensures that they are the same. When we resume from WoWLAN, the firmware may have crashed for whatever reason. In that case, the whole device may be reset which means that the periphery register will hold a meaningless value. When we come to compare trans_pcie->scd_base_addr (which really holds the value we had when we loaded the WoWLAN firmware upon suspend) and the current value of the register, we don't see a match unsurprisingly. Trick the check to avoid a loud yet harmless WARN. Note that when the WoWLAN has crashed, we will see that in iwl_trans_pcie_d3_resume which will let the op_mode know. Once the op_mode is informed that the WowLAN firmware has crashed, it can't do much besides resetting the whole device. Reviewed-by:
-
Calvin Owens authored
commit 28423ad2 upstream. While debugging an issue with excessive softirq usage, I encountered the following note in commit 3e339b5d ("softirq: Use hotplug thread infrastructure"): [ paulmck: Call rcu_note_context_switch() with interrupts enabled. ] ...but despite this note, the patch still calls RCU with IRQs disabled. This seemingly innocuous change caused a significant regression in softirq CPU usage on the sending side of a large TCP transfer (~1 GB/s): when introducing 0.01% packet loss, the softirq usage would jump to around 25%, spiking as high as 50%. Before the change, the usage would never exceed 5%. Moving the call to rcu_note_context_switch() after the cond_sched() call, as it was originally before the hotplug patch, completely eliminated this problem. Signed-off-by:
Calvin Owens <calvinowens@fb.com> Signed-off-by:
Paul E. McKenney <paulmck@linux.vnet.ibm.com> Signed-off-by:
-
Jan Kara authored
commit 6ee8e25f upstream. Commit e9fd702a ("audit: convert audit watches to use fsnotify instead of inotify") broke handling of renames in audit. Audit code wants to update inode number of an inode corresponding to watched name in a directory. When something gets renamed into a directory to a watched name, inotify previously passed moved inode to audit code however new fsnotify code passes directory inode where the change happened. That confuses audit and it starts watching parent directory instead of a file in a directory. This can be observed for example by doing: cd /tmp touch foo bar auditctl -w /tmp/foo touch foo mv bar foo touch foo In audit log we see events like: type=CONFIG_CHANGE msg=audit(1423563584.155:90): auid=1000 ses=2 op="updated rules" path="/tmp/foo" key=(null) list=4 res=1 ... type=PATH msg=audit(1423563584.155:91): item=2 name="bar" inode=1046884 dev=08:0 2 mode=0100644 ouid=0 ogid=0 rdev=00:00 nametype=DELETE type=PATH msg=audit(1423563584.155:91): item=3 name="foo" inode=1046842 dev=08:0 2 mode=0100644 ouid=0 ogid=0 rdev=00:00 nametype=DELETE type=PATH msg=audit(1423563584.155:91): item=4 name="foo" inode=1046884 dev=08:0 2 mode=0100644 ouid=0 ogid=0 rdev=00:00 nametype=CREATE ... and that's it - we see event for the first touch after creating the audit rule, we see events for rename but we don't see any event for the last touch. However we start seeing events for unrelated stuff happening in /tmp. Fix the problem by passing moved inode as data in the FS_MOVED_FROM and FS_MOVED_TO events instead of the directory where the change happens. This doesn't introduce any new problems because noone besides audit_watch.c cares about the passed value: fs/notify/fanotify/fanotify.c cares only about FSNOTIFY_EVENT_PATH events. fs/notify/dnotify/dnotify.c doesn't care about passed 'data' value at all. fs/notify/inotify/inotify_fsnotify.c uses 'data' only for FSNOTIFY_EVENT_PATH. kernel/audit_tree.c doesn't care about passed 'data' at all. kernel/audit_watch.c expects moved inode as 'data'. Fixes: e9fd702a ("audit: convert audit watches to use fsnotify instead of inotify") Signed-off-by:
Jan Kara <jack@suse.cz> Cc: Paul Moore <paul@paul-moore.com> Cc: Eric Paris <eparis@redhat.com> Signed-off-by:
Andrew Morton <akpm@linux-foundation.org> Signed-off-by:
Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by:
-
Dave Chinner authored
commit e9892d3c upstream. The commit 2d3d0c53 ("xfs: lobotomise xfs_trans_read_buf_map()") left a landmine in the tracing code: trace_xfs_trans_buf_read() is now call on all buffers that are read through this interface rather than just buffers in transactions. For buffers outside transaction context, bp->b_fspriv is null, and so the buf log item tracing functions cannot be called. This causes a NULL pointer dereference in the trace_xfs_trans_buf_read() function when tracing is turned on. Signed-off-by:
Dave Chinner <dchinner@redhat.com> Reviewed-by:
Brian Foster <bfoster@redhat.com> Signed-off-by:
Dave Chinner <david@fromorbit.com> Signed-off-by:
-
Dave Chinner authored
commit 3443a3bc upstream. When the superblock is modified in a transaction, the commonly modified fields are not actually copied to the superblock buffer to avoid the buffer lock becoming a serialisation point. However, there are some other operations that modify the superblock fields within the transaction that don't directly log to the superblock but rely on the changes to be applied during the transaction commit (to minimise the buffer lock hold time). When we do this, we fail to mark the buffer log item as being a superblock buffer and that can lead to the buffer not being marked with the corect type in the log and hence causing recovery issues. Fix it by setting the type correctly, similar to xfs_mod_sb()... Tested-by:
-
Dave Chinner authored
commit fe22d552 upstream. Conversion from local to extent format does not set the buffer type correctly on the new extent buffer when a symlink data is moved out of line. Fix the symlink code and leave a comment in the generic bmap code reminding us that the format-specific data copy needs to set the destination buffer type appropriately. Tested-by:
-
Dave Chinner authored
commit f19b872b upstream. This leads to log recovery throwing errors like: XFS (md0): Mounting V5 Filesystem XFS (md0): Starting recovery (logdev: internal) XFS (md0): Unknown buffer type 0! XFS (md0): _xfs_buf_ioapply: no ops on block 0xaea8802/0x1 ffff8800ffc53800: 58 41 47 49 ..... Which is the AGI buffer magic number. Ensure that we set the type appropriately in both unlink list addition and removal. Tested-by:
-
Dave Chinner authored
commit 0d612fb5 upstream. Jan Kara reported that log recovery was finding buffers with invalid types in them. This should not happen, and indicates a bug in the logging of buffers. To catch this, add asserts to the buffer formatting code to ensure that the buffer type is in range when the transaction is committed. We don't set a type on buffers being marked stale - they are not going to get replayed, the format item exists only for recovery to be able to prevent replay of the buffer, so the type does not matter. Hence that needs special casing here. Reported-by:
-
George Spelvin authored
commit 19acc77a upstream. There was a bad typo in commit 43759d4f ("random: use an improved fast_mix() function") and I didn't notice because it "looked right", so I saw what I expected to see when I reviewed it. Only months later did I look and notice it's not the Threefish-inspired mix function that I had designed and optimized. Mea Culpa. Each input bit still has a chance to affect each output bit, and the fast pool is spilled *long* before it fills, so it's not a total disaster, but it's definitely not the intended great improvement. I'm still working on finding better rotation constants. These are good enough, but since it's unrolled twice, it's possible to get better mixing for free by using eight different constants rather than repeating the same four. Signed-off-by:
George Spelvin <linux@horizon.com> Cc: Theodore Ts'o <tytso@mit.edu> Signed-off-by:
-
Matej Dubovy authored
commit 8f0c304c upstream. Please add support for sub BT chip on the combo card Broadcom 43142A0 (in Lenovo E145), 04ca:2007 /sys/kernel/debug/usb/devices T: Bus=05 Lev=01 Prnt=01 Port=01 Cnt=02 Dev#= 3 Spd=12 MxCh= 0 D: Ver= 2.00 Cls=ff(vend.) Sub=01 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=04ca ProdID=2007 Rev= 1.12 S: Manufacturer=Broadcom Corp S: Product=BCM43142A0 S: SerialNumber=28E347EC73BD C:* #Ifs= 4 Cfg#= 1 Atr=e0 MxPwr= 0mA I:* If#= 0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=01 Prot=01 Driver=(none) E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=1ms E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms I:* If#= 1 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=(none) E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms I: If#= 1 Alt= 1 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=(none) E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms I: If#= 1 Alt= 2 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=(none) E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms I: If#= 1 Alt= 3 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=(none) E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms I: If#= 1 Alt= 4 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=(none) E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms I: If#= 1 Alt= 5 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=(none) E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms I:* If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none) E: Ad=84(I) Atr=02(Bulk) MxPS= 32 Ivl=0ms E: Ad=04(O) Atr=02(Bulk) MxPS= 32 Ivl=0ms I:* If#= 3 Alt= 0 #EPs= 0 Cls=fe(app. ) Sub=01 Prot=01 Driver=(none) Firmware for 04ca:2007 can be extracted from the latest Lenovo E145 Bluetooth driver for Windows (driver is however described as BCM20702 but contains also firwmare for BCM43142). Search for BCM43142A0_001.001.011.0122.0153.hex within hex files, then it must be converted using hex2hcd utility. Rename file to BCM43142A0-04ca-2007.hcd, then move to /lib/firmware/brcm/. Signed-off-by:
Matej Dubovy <matej.dubovy@gmail.com> Signed-off-by:
Marcel Holtmann <marcel@holtmann.org> Signed-off-by:
-
Marcel Holtmann authored
commit d049f4e5 upstream. The Dynex/Insignia USB dongles are Broadcom BCM20702B0 based and require firmware update before operation. T: Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 2 Spd=12 MxCh= 0 D: Ver= 2.00 Cls=ff(vend.) Sub=01 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=19ff ProdID=0239 Rev= 1.12 S: Manufacturer=Broadcom Corp S: Product=BCM20702A0 C:* #Ifs= 4 Cfg#= 1 Atr=e0 MxPwr= 0mA I:* If#= 0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=1ms E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms I:* If#= 1 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms I: If#= 1 Alt= 1 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms I: If#= 1 Alt= 2 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms I: If#= 1 Alt= 3 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms I: If#= 1 Alt= 4 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms I: If#= 1 Alt= 5 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms I:* If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none) E: Ad=84(I) Atr=02(Bulk) MxPS= 32 Ivl=0ms E: Ad=04(O) Atr=02(Bulk) MxPS= 32 Ivl=0ms I:* If#= 3 Alt= 0 #EPs= 0 Cls=fe(app. ) Sub=01 Prot=01 Driver=(none) Since this is an unsual USB vendor ID (0x19ff), these dongles are added via USB_DEVICE macro and not USB_VENDOR_AND_INTERFACE_INFO as done for mainstream Broadcom based dongles. The latest known working firmware is BCM20702B0_002.001.014.0527.0557.hex which needs to be converted using hex2hcd utility and then installed as /lib/firmware/brcm/BCM20702A0-19ff-0239.hcd to make this device fully operational. Bluetooth: hci0: BCM: patching hci_ver=06 hci_rev=2000 lmp_ver=06 lmp_subver=410e Bluetooth: hci0: BCM: firmware hci_ver=06 hci_rev=222d lmp_ver=06 lmp_subver=410e With this firmware the device reports support for connectionless slave broadcast (master and slave) feature used by 3D Glasses and TVs. < HCI Command: Read Local Extended Features (0x04|0x0004) plen 1 Page: 2 > HCI Event: Command Complete (0x0e) plen 14 Read Local Extended Features (0x04|0x0004) ncmd 1 Status: Success (0x00) Page: 2/2 Features: 0x0f 0x00 0x00 0x00 0x00 0x00 0x00 0x00 Connectionless Slave Broadcast - Master Connectionless Slave Broadcast - Slave Synchronization Train Synchronization Scan However there are some flaws with this feature. The Set Event Mask Page 2 command is actually not supported and with that all connectionless slave broadcast events are always enabled. < HCI Command: Set Event Mask Page 2 (0x03|0x0063) plen 8 Mask: 0x00000000000f0000 Synchronization Train Received Connectionless Slave Broadcast Receive Connectionless Slave Broadcast Timeout Truncated Page Complete > HCI Event: Command Complete (0x0e) plen 4 Set Event Mask Page 2 (0x03|0x0063) ncmd 1 Status: Unknown HCI Command (0x01) In addition the Synchronization Train Received event is actually broken on this controller. It mixes up the order of parameters. According to the Bluetooth Core specification the fields are like this: struct hci_ev_sync_train_received { __u8 status; bdaddr_t bdaddr; __le32 offset; __u8 map[10]; __u8 lt_addr; __le32 instant; __le16 interval; __u8 service_data; } __packed; This controller however sends the service_data as 5th parameter instead of having it as last parameter. struct hci_ev_sync_train_received { __u8 status; bdaddr_t bdaddr; __le32 offset; __u8 map[10]; __u8 service_data; __u8 lt_addr; __le32 instant; __le16 interval; } __packed; So anybody trying to use this hardware for utilizing connectionless slave broadcast receivers (aka 3D Glasses), be warned about this shortcoming. Signed-off-by:
Johan Hedberg <johan.hedberg@intel.com> Signed-off-by:
-
Szymon Janc authored
commit 91200e9f upstream. Start Discovery was reporting 0 RSSI for invalid RSSI only for BR/EDR devices. LE devices were reported with RSSI 127. Signed-off-by:
Szymon Janc <szymon.janc@tieto.com> Signed-off-by:
-
Rick Dunn authored
commit 9a5abdaa upstream. T: Bus=03 Lev=01 Prnt=01 Port=06 Cnt=02 Dev#= 3 Spd=12 MxCh= 0 D: Ver= 2.00 Cls=ff(vend.) Sub=01 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=0b05 ProdID=17cf Rev= 1.12 S: Manufacturer=Broadcom Corp S: Product=BCM20702A0 S: SerialNumber=54271E3298CD C:* #Ifs= 4 Cfg#= 1 Atr=e0 MxPwr= 0mA I:* If#= 0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=1ms E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms I:* If#= 1 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms I: If#= 1 Alt= 1 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms I: If#= 1 Alt= 2 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms I: If#= 1 Alt= 3 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms I: If#= 1 Alt= 4 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms I: If#= 1 Alt= 5 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms I:* If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none) E: Ad=84(I) Atr=02(Bulk) MxPS= 32 Ivl=0ms E: Ad=04(O) Atr=02(Bulk) MxPS= 32 Ivl=0ms I:* If#= 3 Alt= 0 #EPs= 0 Cls=fe(app. ) Sub=01 Prot=01 Driver=(none) Firmware is extracted from the latest Broadcom BCM4352 Windows driver by extracting the zip and searching the .hex file names for '17cf'. The hex file must then be converted to hcd format using the hex2hcd utility and then moved to /lib/firmware/brcm/. Signed-off-by:
Rick Dunn <rick@rickdunn.com> Signed-off-by:
-
Johan Hedberg authored
commit e12af489 upstream. According to the Bluetooth core specification valid identity addresses are either Public Device Addresses or Static Random Addresses. IRKs received with any other type of address should be discarded since we cannot assume to know the permanent identity of the peer device. This patch fixes a missing check for the Identity Address when receiving the Identity Address Information SMP PDU. Signed-off-by:
-
