- 27 Nov, 2017 2 commits
-
-
Dr. David Alan Gilbert authored
In x2apic mode the LDR is fixed based on the ID rather than separately loadable like it was before x2. When kvm_apic_set_state is called, the base is set, and if it has the X2APIC_ENABLE flag set then the LDR is calculated; however that value gets overwritten by the memcpy a few lines below overwriting it with the value that came from userland. The symptom is a lack of EOI after loading the state (e.g. after a QEMU migration) and is due to the EOI bitmap being wrong due to the incorrect LDR. This was seen with a Win2016 guest under Qemu with irqchip=split whose USB mouse didn't work after a VM migration. This corresponds to RH bug: https://bugzilla.redhat.com/show_bug.cgi?id=1502591Reported-by:
Yiqian Wei <yiwei@redhat.com> Signed-off-by:
Dr. David Alan Gilbert <dgilbert@redhat.com> Cc: stable@vger.kernel.org [Applied fixup from Liran Alon. - Paolo] Signed-off-by:
Paolo Bonzini <pbonzini@redhat.com>
-
Dr. David Alan Gilbert authored
Split out the ldr calculation from kvm_apic_set_x2apic_id since we're about to reuse it in the following patch. Signed-off-by:
-
- 17 Nov, 2017 24 commits
-
-
Paolo Bonzini authored
These bits were not defined until now in common code, but they are now that the kernel supports UMIP too. Signed-off-by: -
Janakarajan Natarajan authored
The function for CPUID 80000001 ECX is set to 0xc0000001. Set it to 0x80000001. Signed-off-by:
Janakarajan Natarajan <Janakarajan.Natarajan@amd.com> Reviewed-by:
Jim Mattson <jmattson@google.com> Reviewed-by:
Krish Sadhukhan <krish.sadhukhan@oracle.com> Reviewed-by:
Borislav Petkov <bp@suse.de> Fixes: d6321d49 ("KVM: x86: generalize guest_cpuid_has_ helpers") Signed-off-by:
Radim Krčmář <rkrcmar@redhat.com>
-
Liran Alon authored
vmx_check_nested_events() should return -EBUSY only in case there is a pending L1 event which requires a VMExit from L2 to L1 but such a VMExit is currently blocked. Such VMExits are blocked either because nested_run_pending=1 or an event was reinjected to L2. vmx_check_nested_events() should return 0 in case there are no pending L1 events which requires a VMExit from L2 to L1 or if a VMExit from L2 to L1 was done internally. However, upstream commit which introduced blocking in case an event was reinjected to L2 (commit acc9ab60 ("KVM: nVMX: Fix pending events injection")) contains a bug: It returns -EBUSY even if there are no pending L1 events which requires VMExit from L2 to L1. This commit fix this issue. Fixes: acc9ab60 ("KVM: nVMX: Fix pending events injection") Signed-off-by:
Liran Alon <liran.alon@oracle.com> Reviewed-by:
Nikita Leshenko <nikita.leshchenko@oracle.com> Signed-off-by:
Konrad Rzeszutek Wilk <konrad.wilk@oracle.com> Signed-off-by:
-
Nikita Leshenko authored
According to 82093AA (IOAPIC) manual, Remote IRR and Delivery Status are read-only. QEMU implements the bits as RO in commit 479c2a1cb7fb ("ioapic: keep RO bits for IOAPIC entry"). Signed-off-by:Wanpeng Li <wanpeng.li@hotmail.com> Reviewed-by:
Steve Rutherford <srutherford@google.com> Signed-off-by:
-
Nikita Leshenko authored
Some OSes (Linux, Xen) use this behavior to clear the Remote IRR bit for IOAPICs without an EOI register. They simulate the EOI message manually by changing the trigger mode to edge and then back to level, with the entry being masked during this. QEMU implements this feature in commit ed1263c363c9 ("ioapic: clear remote irr bit for edge-triggered interrupts") As a side effect, this commit removes an incorrect behavior where Remote IRR was cleared when the redirection table entry was rewritten. This is not consistent with the manual and also opens an opportunity for a strange behavior when a redirection table entry is modified from an interrupt handler that handles the same entry: The modification will clear the Remote IRR bit even though the interrupt handler is still running. Signed-off-by: -
Nikita Leshenko authored
Remote IRR for level-triggered interrupts was previously checked in ioapic_set_irq, but since we now have a check in ioapic_service we can remove the redundant check from ioapic_set_irq. This commit doesn't change semantics. Signed-off-by:
-
Nikita Leshenko authored
Avoid firing a level-triggered interrupt that has the Remote IRR bit set, because that means that some CPU is already processing it. The Remote IRR bit will be cleared after an EOI and the interrupt will refire if the irq line is still asserted. This behavior is aligned with QEMU's IOAPIC implementation that was introduced by commit f99b86b94987 ("x86: ioapic: ignore level irq during processing") in QEMU. Signed-off-by: -
Nikita Leshenko authored
KVM uses ioapic_handled_vectors to track vectors that need to notify the IOAPIC on EOI. The problem is that IOAPIC can be reconfigured while an interrupt with old configuration is pending or running and ioapic_handled_vectors only remembers the newest configuration; thus EOI from the old interrupt is not delievered to the IOAPIC. A previous commit db2bdcbb ("KVM: x86: fix edge EOI and IOAPIC reconfig race") addressed this issue by adding pending edge-triggered interrupts to ioapic_handled_vectors, fixing this race for edge-triggered interrupts. The commit explicitly ignored level-triggered interrupts, but this race applies to them as well: 1) IOAPIC sends a level triggered interrupt vector to VCPU0 2) VCPU0's handler deasserts the irq line and reconfigures the IOAPIC to route the vector to VCPU1. The reconfiguration rewrites only the upper 32 bits of the IOREDTBLn register. (Causes KVM to update ioapic_handled_vectors for VCPU0 and it no longer includes the vector.) 3) VCPU0 sends EOI for the vector, but it's not delievered to the IOAPIC because the ioapic_handled_vectors doesn't include the vector. 4) New interrupts are not delievered to VCPU1 because remote_irr bit is set forever. Therefore, the correct behavior is to add all pending and running interrupts to ioapic_handled_vectors. This commit introduces a slight performance hit similar to commit db2bdcbb ("KVM: x86: fix edge EOI and IOAPIC reconfig race") for the rare case that the vector is reused by a non-IOAPIC source on VCPU0. We prefer to keep solution simple and not handle this case just as the original commit does. Fixes: db2bdcbb ("KVM: x86: fix edge EOI and IOAPIC reconfig race") Signed-off-by:
-
Paolo Bonzini authored
Sometimes, a processor might execute an instruction while another processor is updating the page tables for that instruction's code page, but before the TLB shootdown completes. The interesting case happens if the page is in the TLB. In general, the processor will succeed in executing the instruction and nothing bad happens. However, what if the instruction is an MMIO access? If *that* happens, KVM invokes the emulator, and the emulator gets the updated page tables. If the update side had marked the code page as non present, the page table walk then will fail and so will x86_decode_insn. Unfortunately, even though kvm_fetch_guest_virt is correctly returning X86EMUL_PROPAGATE_FAULT, x86_decode_insn's caller treats the failure as a fatal error if the instruction cannot simply be reexecuted (as is the case for MMIO). And this in fact happened sometimes when rebooting Windows 2012r2 guests. Just checking ctxt->have_exception and injecting the exception if true is enough to fix the case. Thanks to Eduardo Habkost for helping in the debugging of this issue. Reported-by:
Yanan Fu <yfu@redhat.com> Cc: Eduardo Habkost <ehabkost@redhat.com> Cc: stable@vger.kernel.org Signed-off-by:
-
Eyal Moscovici authored
Some guests use these unhandled MSRs very frequently. This cause dmesg to be populated with lots of aggregated messages on usage of ignored MSRs. As ignore_msrs=true means that the user is well-aware his guest use ignored MSRs, allow to also disable the prints on their usage. An example of such guest is ESXi which tends to access a lot to MSR 0x34 (MSR_SMI_COUNT) very frequently. In addition, we have observed this to cause unnecessary delays to guest execution. Such an example is ESXi which experience networking delays in it's guests (L2 guests) because of these prints (even when prints are rate-limited). This can easily be reproduced by pinging from one L2 guest to another. Once in a while, a peak in ping RTT will be observed. Removing these unhandled MSR prints solves the issue. Because these prints can help diagnose issues with guests, this commit only suppress them by a module parameter instead of removing them from code entirely. Signed-off-by:
Eyal Moscovici <eyal.moscovici@oracle.com> Reviewed-by:
-
David Hildenbrand authored
Commit 9d643f63 ("KVM: x86: avoid large stack allocations in em_fxrstor") optimize the stack size, but introduced a guest memory access which might sleep while in atomic. Fix it by introducing, again, a second fxregs_state. Try to avoid large stacks by using noinline. Add some helpful comments. Reported by syzbot: in_atomic(): 1, irqs_disabled(): 0, pid: 2909, name: syzkaller879109 2 locks held by syzkaller879109/2909: #0: (&vcpu->mutex){+.+.}, at: [<ffffffff8106222c>] vcpu_load+0x1c/0x70 arch/x86/kvm/../../../virt/kvm/kvm_main.c:154 #1: (&kvm->srcu){....}, at: [<ffffffff810dd162>] vcpu_enter_guest arch/x86/kvm/x86.c:6983 [inline] #1: (&kvm->srcu){....}, at: [<ffffffff810dd162>] vcpu_run arch/x86/kvm/x86.c:7061 [inline] #1: (&kvm->srcu){....}, at: [<ffffffff810dd162>] kvm_arch_vcpu_ioctl_run+0x1bc2/0x58b0 arch/x86/kvm/x86.c:7222 CPU: 1 PID: 2909 Comm: syzkaller879109 Not tainted 4.13.0-rc4-next-20170811 Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS Bochs 01/01/2011 Call Trace: __dump_stack lib/dump_stack.c:16 [inline] dump_stack+0x194/0x257 lib/dump_stack.c:52 ___might_sleep+0x2b2/0x470 kernel/sched/core.c:6014 __might_sleep+0x95/0x190 kernel/sched/core.c:5967 __might_fault+0xab/0x1d0 mm/memory.c:4383 __copy_from_user include/linux/uaccess.h:71 [inline] __kvm_read_guest_page+0x58/0xa0 arch/x86/kvm/../../../virt/kvm/kvm_main.c:1771 kvm_vcpu_read_guest_page+0x44/0x60 arch/x86/kvm/../../../virt/kvm/kvm_main.c:1791 kvm_read_guest_virt_helper+0x76/0x140 arch/x86/kvm/x86.c:4407 kvm_read_guest_virt_system+0x3c/0x50 arch/x86/kvm/x86.c:4466 segmented_read_std+0x10c/0x180 arch/x86/kvm/emulate.c:819 em_fxrstor+0x27b/0x410 arch/x86/kvm/emulate.c:4022 x86_emulate_insn+0x55d/0x3c50 arch/x86/kvm/emulate.c:5471 x86_emulate_instruction+0x411/0x1ca0 arch/x86/kvm/x86.c:5698 kvm_mmu_page_fault+0x18b/0x2c0 arch/x86/kvm/mmu.c:4854 handle_ept_violation+0x1fc/0x5e0 arch/x86/kvm/vmx.c:6400 vmx_handle_exit+0x281/0x1ab0 arch/x86/kvm/vmx.c:8718 vcpu_enter_guest arch/x86/kvm/x86.c:6999 [inline] vcpu_run arch/x86/kvm/x86.c:7061 [inline] kvm_arch_vcpu_ioctl_run+0x1cee/0x58b0 arch/x86/kvm/x86.c:7222 kvm_vcpu_ioctl+0x64c/0x1010 arch/x86/kvm/../../../virt/kvm/kvm_main.c:2591 vfs_ioctl fs/ioctl.c:45 [inline] do_vfs_ioctl+0x1b1/0x1520 fs/ioctl.c:685 SYSC_ioctl fs/ioctl.c:700 [inline] SyS_ioctl+0x8f/0xc0 fs/ioctl.c:691 entry_SYSCALL_64_fastpath+0x1f/0xbe RIP: 0033:0x437fc9 RSP: 002b:00007ffc7b4d5ab8 EFLAGS: 00000206 ORIG_RAX: 0000000000000010 RAX: ffffffffffffffda RBX: 00000000004002b0 RCX: 0000000000437fc9 RDX: 0000000000000000 RSI: 000000000000ae80 RDI: 0000000000000005 RBP: 0000000000000086 R08: 0000000000000000 R09: 0000000020ae8000 R10: 0000000000009120 R11: 0000000000000206 R12: 0000000000000000 R13: 0000000000000004 R14: 0000000000000004 R15: 0000000020077000 Fixes: 9d643f63 ("KVM: x86: avoid large stack allocations in em_fxrstor") Signed-off-by:
David Hildenbrand <david@redhat.com> Signed-off-by:
-
Wanpeng Li authored
Commit 4f350c6d (kvm: nVMX: Handle deferred early VMLAUNCH/VMRESUME failure properly) can result in L1(run kvm-unit-tests/run_tests.sh vmx_controls in L1) null pointer deference and also L0 calltrace when EPT=0 on both L0 and L1. In L1: BUG: unable to handle kernel paging request at ffffffffc015bf8f IP: vmx_vcpu_run+0x202/0x510 [kvm_intel] PGD 146e13067 P4D 146e13067 PUD 146e15067 PMD 3d2686067 PTE 3d4af9161 Oops: 0003 [#1] PREEMPT SMP CPU: 2 PID: 1798 Comm: qemu-system-x86 Not tainted 4.14.0-rc4+ #6 RIP: 0010:vmx_vcpu_run+0x202/0x510 [kvm_intel] Call Trace: WARNING: kernel stack frame pointer at ffffb86f4988bc18 in qemu-system-x86:1798 has bad value 0000000000000002 In L0: -----------[ cut here ]------------ WARNING: CPU: 6 PID: 4460 at /home/kernel/linux/arch/x86/kvm//vmx.c:9845 vmx_inject_page_fault_nested+0x130/0x140 [kvm_intel] CPU: 6 PID: 4460 Comm: qemu-system-x86 Tainted: G OE 4.14.0-rc7+ #25 RIP: 0010:vmx_inject_page_fault_nested+0x130/0x140 [kvm_intel] Call Trace: paging64_page_fault+0x500/0xde0 [kvm] ? paging32_gva_to_gpa_nested+0x120/0x120 [kvm] ? nonpaging_page_fault+0x3b0/0x3b0 [kvm] ? __asan_storeN+0x12/0x20 ? paging64_gva_to_gpa+0xb0/0x120 [kvm] ? paging64_walk_addr_generic+0x11a0/0x11a0 [kvm] ? lock_acquire+0x2c0/0x2c0 ? vmx_read_guest_seg_ar+0x97/0x100 [kvm_intel] ? vmx_get_segment+0x2a6/0x310 [kvm_intel] ? sched_clock+0x1f/0x30 ? check_chain_key+0x137/0x1e0 ? __lock_acquire+0x83c/0x2420 ? kvm_multiple_exception+0xf2/0x220 [kvm] ? debug_check_no_locks_freed+0x240/0x240 ? debug_smp_processor_id+0x17/0x20 ? __lock_is_held+0x9e/0x100 kvm_mmu_page_fault+0x90/0x180 [kvm] kvm_handle_page_fault+0x15c/0x310 [kvm] ? __lock_is_held+0x9e/0x100 handle_exception+0x3c7/0x4d0 [kvm_intel] vmx_handle_exit+0x103/0x1010 [kvm_intel] ? kvm_arch_vcpu_ioctl_run+0x1628/0x2e20 [kvm] The commit avoids to load host state of vmcs12 as vmcs01's guest state since vmcs12 is not modified (except for the VM-instruction error field) if the checking of vmcs control area fails. However, the mmu context is switched to nested mmu in prepare_vmcs02() and it will not be reloaded since load_vmcs12_host_state() is skipped when nested VMLAUNCH/VMRESUME fails. This patch fixes it by reloading mmu context when nested VMLAUNCH/VMRESUME fails. Reviewed-by:
-
Wanpeng Li authored
According to the SDM, if the "load IA32_BNDCFGS" VM-entry controls is 1, the following checks are performed on the field for the IA32_BNDCFGS MSR: - Bits reserved in the IA32_BNDCFGS MSR must be 0. - The linear address in bits 63:12 must be canonical. Reviewed-by:
-
Wanpeng Li authored
Pedro reported: During tests that we conducted on KVM, we noticed that executing a "PUSH %ES" instruction under KVM produces different results on both memory and the SP register depending on whether EPT support is enabled. With EPT the SP is reduced by 4 bytes (and the written value is 0-padded) but without EPT support it is only reduced by 2 bytes. The difference can be observed when the CS.DB field is 1 (32-bit) but not when it's 0 (16-bit). The internal segment descriptor cache exist even in real/vm8096 mode. The CS.D also should be respected instead of just default operand/address-size/66H prefix/67H prefix during instruction decoding. This patch fixes it by also adjusting operand/address-size according to CS.D. Reported-by:
Pedro Fonseca <pfonseca@cs.washington.edu> Tested-by:
-
Liran Alon authored
In case of instruction-decode failure or emulation failure, x86_emulate_instruction() will call reexecute_instruction() which will attempt to use the cr2 value passed to x86_emulate_instruction(). However, when x86_emulate_instruction() is called from emulate_instruction(), cr2 is not passed (passed as 0) and therefore it doesn't make sense to execute reexecute_instruction() logic at all. Fixes: 51d8b661 ("KVM: cleanup emulate_instruction") Signed-off-by:
-
Liran Alon authored
On this case, handle_emulation_failure() fills kvm_run with internal-error information which it expects to be delivered to user-mode for further processing. However, the code reports a wrong return-value which makes KVM to never return to user-mode on this scenario. Fixes: 6d77dbfc ("KVM: inject #UD if instruction emulation fails and exit to userspace") Signed-off-by:
-
Liran Alon authored
Instruction emulation after trapping a #UD exception can result in an MMIO access, for example when emulating a MOVBE on a processor that doesn't support the instruction. In this case, the #UD vmexit handler must exit to user mode, but there wasn't any code to do so. Add it for both VMX and SVM. Signed-off-by:
-
Liran Alon authored
When running L2, #UD should be intercepted by L1 or just forwarded directly to L2. It should not reach L0 x86 emulator. Therefore, set intercept for #UD only based on L1 exception-bitmap. Also add WARN_ON_ONCE() on L0 #UD intercept handlers to make sure it is never reached while running L2. This improves commit ae1f5767 ("KVM: nVMX: Do not emulate #UD while in guest mode") by removing an unnecessary exit from L2 to L0 on #UD when L1 doesn't intercept it. In addition, SVM L0 #UD intercept handler doesn't handle correctly the case it is raised from L2. In this case, it should forward the #UD to guest instead of x86 emulator. As done in VMX #UD intercept handler. This commit fixes this issue as-well. Signed-off-by:
-
Liran Alon authored
When guest passes KVM it's pvclock-page GPA via WRMSR to MSR_KVM_SYSTEM_TIME / MSR_KVM_SYSTEM_TIME_NEW, KVM don't initialize pvclock-page to some start-values. It just requests a clock-update which will happen before entering to guest. The clock-update logic will call kvm_setup_pvclock_page() to update the pvclock-page with info. However, kvm_setup_pvclock_page() *wrongly* assumes that the version-field is initialized to an even number. This is wrong because at first-time write, field could be any-value. Fix simply makes sure that if first-time version-field is odd, increment it once more to make it even and only then start standard logic. This follows same logic as done in other pvclock shared-pages (See kvm_write_wall_clock() and record_steal_time()). Signed-off-by:
-
Paolo Bonzini authored
To simplify testing of these rarely used code paths, add a module parameter that turns it on. One eventinj.flat test (NMI after iret) fails when loading kvm_intel with vnmi=0. Signed-off-by:
-
Paolo Bonzini authored
This is more or less a revert of commit 2c82878b ("KVM: VMX: require virtual NMI support", 2017-03-27); it turns out that Core 2 Duo machines only had virtual NMIs in some SKUs. The revert is not trivial because in the meanwhile there have been several fixes to nested NMI injection. Therefore, the entire vNMI state is moved to struct loaded_vmcs. Another change compared to before the patch is a simplification here: if (unlikely(!cpu_has_virtual_nmis() && vmx->soft_vnmi_blocked && !(is_guest_mode(vcpu) && nested_cpu_has_virtual_nmis( get_vmcs12(vcpu))))) { The final condition here is always true (because nested_cpu_has_virtual_nmis is always false) and is removed. Fixes: 2c82878b Fixes: https://bugzilla.redhat.com/show_bug.cgi?id=1490803 Cc: stable@vger.kernel.org Signed-off-by:
-
Paolo Bonzini authored
For many years some users of assigned devices have reported worse performance on AMD processors with NPT than on AMD without NPT, Intel or bare metal. The reason turned out to be that SVM is discarding the guest PAT setting and uses the default (PA0=PA4=WB, PA1=PA5=WT, PA2=PA6=UC-, PA3=UC). The guest might be using a different setting, and especially might want write combining but isn't getting it (instead getting slow UC or UC- accesses). Thanks a lot to geoff@hostfission.com for noticing the relation to the g_pat setting. The patch has been tested also by a bunch of people on VFIO users forums. Fixes: 709ddebf Fixes: https://bugzilla.kernel.org/show_bug.cgi?id=196409 Cc: stable@vger.kernel.org Signed-off-by:
Nick Sarnie <commendsarnex@gmail.com> Signed-off-by:
-
Paolo Bonzini authored
Merge tag 'kvm-arm-gicv4-for-v4.15' of git://git.kernel.org/pub/scm/linux/kernel/git/kvmarm/kvmarm into HEAD GICv4 Support for KVM/ARM for v4.15
-
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-socLinus Torvalds authored
Pull ARM SoC driver updates from Arnd Bergmann: "This branch contains platform-related driver updates for ARM and ARM64, these are the areas that bring the changes: New drivers: - driver support for Renesas R-Car V3M (R8A77970) - power management support for Amlogic GX - a new driver for the Tegra BPMP thermal sensor - a new bus driver for Technologic Systems NBUS Changes for subsystems that prefer to merge through arm-soc: - the usual updates for reset controller drivers from Philipp Zabel, with five added drivers for SoCs in the arc, meson, socfpa, uniphier and mediatek families - updates to the ARM SCPI and PSCI frameworks, from Sudeep Holla, Heiner Kallweit and Lorenzo Pieralisi Changes specific to some ARM-based SoC - the Freescale/NXP DPAA QBMan drivers from PowerPC can now work on ARM as well - several changes for power management on Broadcom SoCs - various improvements on Qualcomm, Broadcom, Amlogic, Atmel, Mediatek - minor Cleanups for Samsung, TI OMAP SoCs" [ NOTE! This doesn't work without the previous ARM SoC device-tree pull, because the R8A77970 driver is missing a header file that came from that pull. The fact that this got merged afterwards only fixes it at this point, and bisection of that driver will fail if/when you walk into the history of that driver. - Linus ] * tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (96 commits) soc: amlogic: meson-gx-pwrc-vpu: fix power-off when powered by bootloader bus: add driver for the Technologic Systems NBUS memory: omap-gpmc: Remove deprecated gpmc_update_nand_reg() soc: qcom: remove unused label soc: amlogic: gx pm domain: add PM and OF dependencies drivers/firmware: psci_checker: Add missing destroy_timer_on_stack() dt-bindings: power: add amlogic meson power domain bindings soc: amlogic: add Meson GX VPU Domains driver soc: qcom: Remote filesystem memory driver dt-binding: soc: qcom: Add binding for rmtfs memory of: reserved_mem: Accessor for acquiring reserved_mem of/platform: Generalize /reserved-memory handling soc: mediatek: pwrap: fix fatal compiler error soc: mediatek: pwrap: fix compiler errors arm64: mediatek: cleanup message for platform selection soc: Allow test-building of MediaTek drivers soc: mediatek: place Kconfig for all SoC drivers under menu soc: mediatek: pwrap: add support for MT7622 SoC soc: mediatek: pwrap: add common way for setup CS timing extenstion soc: mediatek: pwrap: add MediaTek MT6380 as one slave of pwrap ..
-
- 16 Nov, 2017 14 commits
-
-
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-socLinus Torvalds authored
Pull ARM device-tree updates from Arnd Bergmann: "We add device tree files for a couple of additional SoCs in various areas: Allwinner R40/V40 for entertainment, Broadcom Hurricane 2 for networking, Amlogic A113D for audio, and Renesas R-Car V3M for automotive. As usual, lots of new boards get added based on those and other SoCs: - Actions S500 based CubieBoard6 single-board computer - Amlogic Meson-AXG A113D based development board - Amlogic S912 based Khadas VIM2 single-board computer - Amlogic S912 based Tronsmart Vega S96 set-top-box - Allwinner H5 based NanoPi NEO Plus2 single-board computer - Allwinner R40 based Banana Pi M2 Ultra and Berry single-board computers - Allwinner A83T based TBS A711 Tablet - Broadcom Hurricane 2 based Ubiquiti UniFi Switch 8 - Broadcom bcm47xx based Luxul XAP-1440/XAP-810/ABR-4500/XBR-4500 wireless access points and routers - NXP i.MX51 based Zodiac Inflight Innovations RDU1 board - NXP i.MX53 based GE Healthcare PPD biometric monitor - NXP i.MX6 based Pistachio single-board computer - NXP i.MX6 based Vining-2000 automotive diagnostic interface - NXP i.MX6 based Ka-Ro TX6 Computer-on-Module in additional variants - Qualcomm MSM8974 (Snapdragon 800) based Fairphone 2 phone - Qualcomm MSM8974pro (Snapdragon 801) based Sony Xperia Z2 Tablet - Realtek RTD1295 based set-top-boxes MeLE V9 and PROBOX2 AVA - Renesas R-Car V3M (R8A77970) SoC and "Eagle" reference board - Renesas H3ULCB and M3ULCB "Kingfisher" extension infotainment boards - Renasas r8a7745 based iWave G22D-SODIMM SoM - Rockchip rk3288 based Amarula Vyasa single-board computer - Samsung Exynos5800 based Odroid HC1 single-board computer For existing SoC support, there was a lot of ongoing work, as usual most of that concentrated on the Renesas, Rockchip, OMAP, i.MX, Amlogic and Allwinner platforms, but others were also active. Rob Herring and many others worked on reducing the number of issues that the latest version of 'dtc' now warns about. Unfortunately there is still a lot left to do. A rework of the ARM foundation model introduced several new files for common variations of the model" * tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (599 commits) arm64: dts: uniphier: route on-board device IRQ to GPIO controller for PXs3 dt-bindings: bus: Add documentation for the Technologic Systems NBUS arm64: dts: actions: s900-bubblegum-96: Add fake uart5 clock ARM: dts: owl-s500: Add CubieBoard6 dt-bindings: arm: actions: Add CubieBoard6 ARM: dts: owl-s500-guitar-bb-rev-b: Add fake uart3 clock ARM: dts: owl-s500: Set power domains for CPU2 and CPU3 arm: dts: mt7623: remove unused compatible string for pio node arm: dts: mt7623: update usb related nodes arm: dts: mt7623: update crypto node ARM: dts: sun8i: a711: Enable USB OTG ARM: dts: sun8i: a711: Add regulator support ARM: dts: sun8i: a83t: bananapi-m3: Enable AP6212 WiFi on mmc1 ARM: dts: sun8i: a83t: cubietruck-plus: Enable AP6330 WiFi on mmc1 ARM: dts: sun8i: a83t: Move mmc1 pinctrl setting to dtsi file ARM: dts: sun8i: a83t: allwinner-h8homlet-v2: Add AXP818 regulator nodes ARM: dts: sun8i: a83t: bananapi-m3: Add AXP813 regulator nodes ARM: dts: sun8i: a83t: cubietruck-plus: Add AXP818 regulator nodes ARM: dts: sunxi: Add dtsi for AXP81x PMIC arm64: dts: allwinner: H5: Restore EMAC changes ... -
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-socLinus Torvalds authored
Pull ARM SoC platform updates from Arnd Bergmann: "Most of the commits are for defconfig changes, to enable newly added drivers or features that people have started using. For the changed lines lines, we have mostly cleanups, the affected platforms are OMAP, Versatile, EP93xx, Samsung, Broadcom, i.MX, and Actions. The largest single change is the introduction of the TI "sysc" bus driver, with the intention of cleaning up more legacy code. Two new SoC platforms get added this time: - Allwinner R40 is a modernized version of the A20 chip, now with a Quad-Core ARM Cortex-A7. According to the manufacturer, it is intended for "Smart Hardware" - Broadcom Hurricane 2 (Aka Strataconnect BCM5334X) is a family of chips meant for managed gigabit ethernet switches, based around a Cortex-A9 CPU. Finally, we gain SMP support for two platforms: Renesas R-Car E2 and Amlogic Meson8/8b, which were previously added but only supported uniprocessor operation" * tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (118 commits) ARM: multi_v7_defconfig: Select RPMSG_VIRTIO as module ARM: multi_v7_defconfig: enable CONFIG_GPIO_UNIPHIER arm64: defconfig: enable CONFIG_GPIO_UNIPHIER ARM: meson: enable MESON_IRQ_GPIO in Kconfig for meson8b ARM: meson: Add SMP bringup code for Meson8 and Meson8b ARM: smp_scu: allow the platform code to read the SCU CPU status ARM: smp_scu: add a helper for powering on a specific CPU dt-bindings: Amlogic: Add Meson8 and Meson8b SMP related documentation ARM: OMAP3: Delete an unnecessary variable initialisation in omap3xxx_hwmod_init() ARM: OMAP3: Use common error handling code in omap3xxx_hwmod_init() ARM: defconfig: select the right SX150X driver arm64: defconfig: Enable QCOM_IOMMU arm64: Add ThunderX drivers to defconfig arm64: defconfig: Enable Tegra PCI controller cpufreq: imx6q: Move speed grading check to cpufreq driver arm64: defconfig: re-enable Qualcomm DB410c USB ARM: configs: stm32: Add MDMA support in STM32 defconfig ARM: imx: Enable cpuidle for i.MX6DL starting at 1.1 bus: ti-sysc: Fix unbalanced pm_runtime_enable by adding remove bus: ti-sysc: mark PM functions as __maybe_unused ... -
git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhostLinus Torvalds authored
Pull virtio updates from Michael Tsirkin: "Fixes in qemu, vhost and virtio" * tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost: fw_cfg: fix the command line module name vhost/vsock: fix uninitialized vhost_vsock->guest_cid vhost: fix end of range for access_ok vhost/scsi: Use safe iteration in vhost_scsi_complete_cmd_work() virtio_balloon: fix deadlock on OOM
-
git://git.kernel.org/pub/scm/linux/kernel/git/xen/tipLinus Torvalds authored
Pull xen updates from Juergen Gross: "Xen features and fixes for v4.15-rc1 Apart from several small fixes it contains the following features: - a series by Joao Martins to add vdso support of the pv clock interface - a series by Juergen Gross to add support for Xen pv guests to be able to run on 5 level paging hosts - a series by Stefano Stabellini adding the Xen pvcalls frontend driver using a paravirtualized socket interface" * tag 'for-linus-4.15-rc1-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip: (34 commits) xen/pvcalls: fix potential endless loop in pvcalls-front.c xen/pvcalls: Add MODULE_LICENSE() MAINTAINERS: xen, kvm: track pvclock-abi.h changes x86/xen/time: setup vcpu 0 time info page x86/xen/time: set pvclock flags on xen_time_init() x86/pvclock: add setter for pvclock_pvti_cpu0_va ptp_kvm: probe for kvm guest availability xen/privcmd: remove unused variable pageidx xen: select grant interface version xen: update arch/x86/include/asm/xen/cpuid.h xen: add grant interface version dependent constants to gnttab_ops xen: limit grant v2 interface to the v1 functionality xen: re-introduce support for grant v2 interface xen: support priv-mapping in an HVM tools domain xen/pvcalls: remove redundant check for irq >= 0 xen/pvcalls: fix unsigned less than zero error check xen/time: Return -ENODEV from xen_get_wallclock() xen/pvcalls-front: mark expected switch fall-through xen: xenbus_probe_frontend: mark expected switch fall-throughs xen/time: do not decrease steal time after live migration on xen ... -
git://git.kernel.org/pub/scm/virt/kvm/kvmLinus Torvalds authored
Pull KVM updates from Radim Krčmář: "First batch of KVM changes for 4.15 Common: - Python 3 support in kvm_stat - Accounting of slabs to kmemcg ARM: - Optimized arch timer handling for KVM/ARM - Improvements to the VGIC ITS code and introduction of an ITS reset ioctl - Unification of the 32-bit fault injection logic - More exact external abort matching logic PPC: - Support for running hashed page table (HPT) MMU mode on a host that is using the radix MMU mode; single threaded mode on POWER 9 is added as a pre-requisite - Resolution of merge conflicts with the last second 4.14 HPT fixes - Fixes and cleanups s390: - Some initial preparation patches for exitless interrupts and crypto - New capability for AIS migration - Fixes x86: - Improved emulation of LAPIC timer mode changes, MCi_STATUS MSRs, and after-reset state - Refined dependencies for VMX features - Fixes for nested SMI injection - A lot of cleanups" * tag 'kvm-4.15-1' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (89 commits) KVM: s390: provide a capability for AIS state migration KVM: s390: clear_io_irq() requests are not expected for adapter interrupts KVM: s390: abstract conversion between isc and enum irq_types KVM: s390: vsie: use common code functions for pinning KVM: s390: SIE considerations for AP Queue virtualization KVM: s390: document memory ordering for kvm_s390_vcpu_wakeup KVM: PPC: Book3S HV: Cosmetic post-merge cleanups KVM: arm/arm64: fix the incompatible matching for external abort KVM: arm/arm64: Unify 32bit fault injection KVM: arm/arm64: vgic-its: Implement KVM_DEV_ARM_ITS_CTRL_RESET KVM: arm/arm64: Document KVM_DEV_ARM_ITS_CTRL_RESET KVM: arm/arm64: vgic-its: Free caches when GITS_BASER Valid bit is cleared KVM: arm/arm64: vgic-its: New helper functions to free the caches KVM: arm/arm64: vgic-its: Remove kvm_its_unmap_device arm/arm64: KVM: Load the timer state when enabling the timer KVM: arm/arm64: Rework kvm_timer_should_fire KVM: arm/arm64: Get rid of kvm_timer_flush_hwstate KVM: arm/arm64: Avoid phys timer emulation in vcpu entry/exit KVM: arm/arm64: Move phys_timer_emulate function KVM: arm/arm64: Use kvm_arm_timer_set/get_reg for guest register traps ... -
git://git.armlinux.org.uk/~rmk/linux-armLinus Torvalds authored
Pull ARM updates from Russell King: - add support for ELF fdpic binaries on both MMU and noMMU platforms - linker script cleanups - support for compressed .data section for XIP images - discard memblock arrays when possible - various cleanups - atomic DMA pool updates - better diagnostics of missing/corrupt device tree - export information to allow userspace kexec tool to place images more inteligently, so that the device tree isn't overwritten by the booting kernel - make early_printk more efficient on semihosted systems - noMMU cleanups - SA1111 PCMCIA update in preparation for further cleanups * 'for-linus' of git://git.armlinux.org.uk/~rmk/linux-arm: (38 commits) ARM: 8719/1: NOMMU: work around maybe-uninitialized warning ARM: 8717/2: debug printch/printascii: translate '\n' to "\r\n" not "\n\r" ARM: 8713/1: NOMMU: Support MPU in XIP configuration ARM: 8712/1: NOMMU: Use more MPU regions to cover memory ARM: 8711/1: V7M: Add support for MPU to M-class ARM: 8710/1: Kconfig: Kill CONFIG_VECTORS_BASE ARM: 8709/1: NOMMU: Disallow MPU for XIP ARM: 8708/1: NOMMU: Rework MPU to be mostly done in C ARM: 8707/1: NOMMU: Update MPU accessors to use cp15 helpers ARM: 8706/1: NOMMU: Move out MPU setup in separate module ARM: 8702/1: head-common.S: Clear lr before jumping to start_kernel() ARM: 8705/1: early_printk: use printascii() rather than printch() ARM: 8703/1: debug.S: move hexbuf to a writable section ARM: add additional table to compressed kernel ARM: decompressor: fix BSS size calculation pcmcia: sa1111: remove special sa1111 mmio accessors pcmcia: sa1111: use sa1111_get_irq() to obtain IRQ resources ARM: better diagnostics with missing/corrupt dtb ARM: 8699/1: dma-mapping: Remove init_dma_coherent_pool_size() ARM: 8698/1: dma-mapping: Mark atomic_pool as __ro_after_init ..
-
git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linuxLinus Torvalds authored
Pull powerpc updates from Michael Ellerman: "A bit of a small release, I suspect in part due to me travelling for KS. But my backlog of patches to review is smaller than usual, so I think in part folks just didn't send as much this cycle. Non-highlights: - Five fixes for the >128T address space handling, both to fix bugs in our implementation and to bring the semantics exactly into line with x86. Highlights: - Support for a new OPAL call on bare metal machines which gives us a true NMI (ie. is not masked by MSR[EE]=0) for debugging etc. - Support for Power9 DD2 in the CXL driver. - Improvements to machine check handling so that uncorrectable errors can be reported into the generic memory_failure() machinery. - Some fixes and improvements for VPHN, which is used under PowerVM to notify the Linux partition of topology changes. - Plumbing to enable TM (transactional memory) without suspend on some Power9 processors (PPC_FEATURE2_HTM_NO_SUSPEND). - Support for emulating vector loads form cache-inhibited memory, on some Power9 revisions. - Disable the fast-endian switch "syscall" by default (behind a CONFIG), we believe it has never had any users. - A major rework of the API drivers use when initiating and waiting for long running operations performed by OPAL firmware, and changes to the powernv_flash driver to use the new API. - Several fixes for the handling of FP/VMX/VSX while processes are using transactional memory. - Optimisations of TLB range flushes when using the radix MMU on Power9. - Improvements to the VAS facility used to access coprocessors on Power9, and related improvements to the way the NX crypto driver handles requests. - Implementation of PMEM_API and UACCESS_FLUSHCACHE for 64-bit. Thanks to: Alexey Kardashevskiy, Alistair Popple, Allen Pais, Andrew Donnellan, Aneesh Kumar K.V, Arnd Bergmann, Balbir Singh, Benjamin Herrenschmidt, Breno Leitao, Christophe Leroy, Christophe Lombard, Cyril Bur, Frederic Barrat, Gautham R. Shenoy, Geert Uytterhoeven, Guilherme G. Piccoli, Gustavo Romero, Haren Myneni, Joel Stanley, Kamalesh Babulal, Kautuk Consul, Markus Elfring, Masami Hiramatsu, Michael Bringmann, Michael Neuling, Michal Suchanek, Naveen N. Rao, Nicholas Piggin, Oliver O'Halloran, Paul Mackerras, Pedro Miraglia Franco de Carvalho, Philippe Bergheaud, Sandipan Das, Seth Forshee, Shriya, Stephen Rothwell, Stewart Smith, Sukadev Bhattiprolu, Tyrel Datwyler, Vaibhav Jain, Vaidyanathan Srinivasan, and William A. Kennington III" * tag 'powerpc-4.15-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux: (151 commits) powerpc/64s: Fix Power9 DD2.0 workarounds by adding DD2.1 feature powerpc/64s: Fix masking of SRR1 bits on instruction fault powerpc/64s: mm_context.addr_limit is only used on hash powerpc/64s/radix: Fix 128TB-512TB virtual address boundary case allocation powerpc/64s/hash: Allow MAP_FIXED allocations to cross 128TB boundary powerpc/64s/hash: Fix fork() with 512TB process address space powerpc/64s/hash: Fix 128TB-512TB virtual address boundary case allocation powerpc/64s/hash: Fix 512T hint detection to use >= 128T powerpc: Fix DABR match on hash based systems powerpc/signal: Properly handle return value from uprobe_deny_signal() powerpc/fadump: use kstrtoint to handle sysfs store powerpc/lib: Implement UACCESS_FLUSHCACHE API powerpc/lib: Implement PMEM API powerpc/powernv/npu: Don't explicitly flush nmmu tlb powerpc/powernv/npu: Use flush_all_mm() instead of flush_tlb_mm() powerpc/powernv/idle: Round up latency and residency values powerpc/kprobes: refactor kprobe_lookup_name for safer string operations powerpc/kprobes: Blacklist emulate_update_regs() from kprobes powerpc/kprobes: Do not disable interrupts for optprobes and kprobes_on_ftrace powerpc/kprobes: Disable preemption before invoking probe handler for optprobes ... -
git://git.kernel.org/pub/scm/linux/kernel/git/ebiederm/user-namespaceLinus Torvalds authored
Pull user namespace update from Eric Biederman: "The only change that is production ready this round is the work to increase the number of uid and gid mappings a user namespace can support from 5 to 340. This code was carefully benchmarked and it was confirmed that in the existing cases the performance remains the same. In the worst case with 340 mappings an cache cold stat times go from 158ns to 248ns. That is noticable but still quite small, and only the people who are doing crazy things pay the cost. This work uncovered some documentation and cleanup opportunities in the mapping code, and patches to make those cleanups and improve the documentation will be coming in the next merge window" * 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ebiederm/user-namespace: userns: Simplify insert_extent userns: Make map_id_down a wrapper for map_id_range_down userns: Don't read extents twice in m_start userns: Simplify the user and group mapping functions userns: Don't special case a count of 0 userns: bump idmap limits to 340 userns: use union in {g,u}idmap struct
-
git://git.kernel.org/pub/scm/linux/kernel/git/jaegeuk/f2fsLinus Torvalds authored
Pull f2fs updates from Jaegeuk Kim: "In this round, we introduce sysfile-based quota support which is required for Android by default. In addition, we allow that users are able to reserve some blocks in runtime to mitigate performance drops in low free space. Enhancements: - assign proper data segments according to write_hints given by user - issue cache_flush on dirty devices only among multiple devices - exploit cp_error flag and add more faults to enhance fault injection test - conduct more readaheads during f2fs_readdir - add a range for discard commands Bug fixes: - fix zero stat->st_blocks when inline_data is set - drop crypto key and free stale memory pointer while evict_inode is failing - fix some corner cases in free space and segment management - fix wrong last_disk_size This series includes lots of clean-ups and code enhancement in terms of xattr operations, discard/flush command control. In addition, it adds versatile debugfs entries to monitor f2fs status" * tag 'f2fs-for-4.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/jaegeuk/f2fs: (75 commits) f2fs: deny accessing encryption policy if encryption is off f2fs: inject fault in inc_valid_node_count f2fs: fix to clear FI_NO_PREALLOC f2fs: expose quota information in debugfs f2fs: separate nat entry mem alloc from nat_tree_lock f2fs: validate before set/clear free nat bitmap f2fs: avoid opened loop codes in __add_ino_entry f2fs: apply write hints to select the type of segments for buffered write f2fs: introduce scan_curseg_cache for cleanup f2fs: optimize the way of traversing free_nid_bitmap f2fs: keep scanning until enough free nids are acquired f2fs: trace checkpoint reason in fsync() f2fs: keep isize once block is reserved cross EOF f2fs: avoid race in between GC and block exchange f2fs: save a multiplication for last_nid calculation f2fs: fix summary info corruption f2fs: remove dead code in update_meta_page f2fs: remove unneeded semicolon f2fs: don't bother with inode->i_version f2fs: check curseg space before foreground GC ... -
git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-fsLinus Torvalds authored
Pull AFS updates from David Howells: "kAFS filesystem driver overhaul. The major points of the overhaul are: (1) Preliminary groundwork is laid for supporting network-namespacing of kAFS. The remainder of the namespacing work requires some way to pass namespace information to submounts triggered by an automount. This requires something like the mount overhaul that's in progress. (2) sockaddr_rxrpc is used in preference to in_addr for holding addresses internally and add support for talking to the YFS VL server. With this, kAFS can do everything over IPv6 as well as IPv4 if it's talking to servers that support it. (3) Callback handling is overhauled to be generally passive rather than active. 'Callbacks' are promises by the server to tell us about data and metadata changes. Callbacks are now checked when we next touch an inode rather than actively going and looking for it where possible. (4) File access permit caching is overhauled to store the caching information per-inode rather than per-directory, shared over subordinate files. Whilst older AFS servers only allow ACLs on directories (shared to the files in that directory), newer AFS servers break that restriction. To improve memory usage and to make it easier to do mass-key removal, permit combinations are cached and shared. (5) Cell database management is overhauled to allow lighter locks to be used and to make cell records autonomous state machines that look after getting their own DNS records and cleaning themselves up, in particular preventing races in acquiring and relinquishing the fscache token for the cell. (6) Volume caching is overhauled. The afs_vlocation record is got rid of to simplify things and the superblock is now keyed on the cell and the numeric volume ID only. The volume record is tied to a superblock and normal superblock management is used to mediate the lifetime of the volume fscache token. (7) File server record caching is overhauled to make server records independent of cells and volumes. A server can be in multiple cells (in such a case, the administrator must make sure that the VL services for all cells correctly reflect the volumes shared between those cells). Server records are now indexed using the UUID of the server rather than the address since a server can have multiple addresses. (8) File server rotation is overhauled to handle VMOVED, VBUSY (and similar), VOFFLINE and VNOVOL indications and to handle rotation both of servers and addresses of those servers. The rotation will also wait and retry if the server says it is busy. (9) Data writeback is overhauled. Each inode no longer stores a list of modified sections tagged with the key that authorised it in favour of noting the modified region of a page in page->private and storing a list of keys that made modifications in the inode. This simplifies things and allows other keys to be used to actually write to the server if a key that made a modification becomes useless. (10) Writable mmap() is implemented. This allows a kernel to be build entirely on AFS. Note that Pre AFS-3.4 servers are no longer supported, though this can be added back if necessary (AFS-3.4 was released in 1998)" * tag 'afs-next-20171113' of git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-fs: (35 commits) afs: Protect call->state changes against signals afs: Trace page dirty/clean afs: Implement shared-writeable mmap afs: Get rid of the afs_writeback record afs: Introduce a file-private data record afs: Use a dynamic port if 7001 is in use afs: Fix directory read/modify race afs: Trace the sending of pages afs: Trace the initiation and completion of client calls afs: Fix documentation on # vs % prefix in mount source specification afs: Fix total-length calculation for multiple-page send afs: Only progress call state at end of Tx phase from rxrpc callback afs: Make use of the YFS service upgrade to fully support IPv6 afs: Overhaul volume and server record caching and fileserver rotation afs: Move server rotation code into its own file afs: Add an address list concept afs: Overhaul cell database management afs: Overhaul permit caching afs: Overhaul the callback handling afs: Rename struct afs_call server member to cm_server ... -
git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrlLinus Torvalds authored
Pull pin control updates from Linus Walleij: "This is the bulk of pin control changes for the v4.15 kernel cycle: Core: - The pin control Kconfig entry PINCTRL is now turned into a menuconfig option. This obviously has the implication of making the subsystem menu visible in menuconfig. This is happening because of two things: (a) Intel have started to deploy and depend on pin controllers in a way that is affecting users directly. This happens on the highly integrated laptop chipsets named after geographical places: baytrail, broxton, cannonlake, cedarfork, cherryview, denverton, geminilake, lewisburg, merrifield, sunrisepoint... It started a while back and now it is ever more evident that this is crucial infrastructure for x86 laptops and not an embedded obscurity anymore. Users need to be aware. (b) Pin control expanders on I2C and SPI that are arch-agnostic. Currently Semtech SX150X and Microchip MCP28x08 but more are expected. Users will have to be able to configure these in directly for their set-up. - Just go and select GPIOLIB now that we made sure that GPIOLIB is a very vanilla subsystem. Do not depend on it, if we need it, select it. - Exposing the pin control subsystem in menuconfig uncovered a bunch of obscure bugs that are now hopefully fixed, all more or less pertaining to Blackfin. - Unified namespace for cross-calls between pin control and GPIO. - New support for clock skew/delay generic DT bindings and generic pin config options for this. - Minor documentation improvements. Various: - The Renesas SH-PFC pin controller has evolved a lot. It seems Renesas are churning out new SoCs by the minute. - A bunch of non-critical fixes for the Rockchip driver. - Improve the use of library functions instead of open coding. - Support the MCP28018 variant in the MCP28x08 driver. - Static constifying" * tag 'pinctrl-v4.15-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (91 commits) pinctrl: gemini: Fix missing pad descriptions pinctrl: Add some depends on HAS_IOMEM pinctrl: samsung/s3c24xx: add CONFIG_OF dependency pinctrl: gemini: Fix GMAC groups pinctrl: qcom: spmi-gpio: Add pmi8994 gpio support pinctrl: ti-iodelay: remove redundant unused variable dev pinctrl: max77620: Use common error handling code in max77620_pinconf_set() pinctrl: gemini: Implement clock skew/delay config pinctrl: gemini: Use generic DT parser pinctrl: Add skew-delay pin config and bindings pinctrl: armada-37xx: Add edge both type gpio irq support pinctrl: uniphier: remove eMMC hardware reset pin-mux pinctrl: rockchip: Add iomux-route switching support for rk3288 pinctrl: intel: Add Intel Cedar Fork PCH pin controller support pinctrl: intel: Make offset to interrupt status register configurable pinctrl: sunxi: Enforce the strict mode by default pinctrl: sunxi: Disable strict mode for old pinctrl drivers pinctrl: sunxi: Introduce the strict flag pinctrl: sh-pfc: Save/restore registers for PSCI system suspend pinctrl: sh-pfc: r8a7796: Use generic IOCTRL register description ... -
git://git.kernel.org/pub/scm/linux/kernel/git/lee/backlightLinus Torvalds authored
Pull backlight updates from Lee Jones: - handle 32bit overflow in pwm_bl - remove redundant code/checks in tps65217_bl and ili922x * tag 'backlight-next-4.15' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/backlight: backlight: ili922x: Remove redundant variable len backlight: tps65217_bl: Remove unnecessary default brightness check backlight: pwm_bl: Fix overflow condition
-
git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfdLinus Torvalds authored
Pull MFD updates from Lee Jones: "New drivers: - Add support for Cherry Trail Dollar Cove TI PMIC - Add support for Add Spreadtrum SC27xx series PMICs New device support: - Add support Regulator to axp20x New functionality: - Add DT support; aspeed-scu sc27xx-pmic - Add power saving support; rts5249 Fix-ups: - DT clean-up/rework; tps65217, max77693, iproc-cdru, iproc-mhb, tps65218 - Staticise/constify; stw481x - Use new succinct IRQ API; fsl-imx25-tsadc - Kconfig fix-ups; MFD_TPS65218 - Identify SPI method; lpc_ich - Use managed resources (devm_*) calls; ssbi - Remove unused/obsolete code/documentation; mc13xxx Bug fixes: - Fix typo in MAINTAINERS - Fix error handling; mxs-lradc - Clean-up IRQs on .remove; fsl-imx25-tsadc" * tag 'mfd-next-4.15' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd: (21 commits) dt-bindings: mfd: mc13xxx: Remove obsolete property mfd: axp20x: Add axp20x-regulator cell for AXP813 mfd: Add Spreadtrum SC27xx series PMICs driver dt-bindings: mfd: Add Spreadtrum SC27xx PMIC documentation mfd: ssbi: Use devm_of_platform_populate() mfd: fsl-imx25: Clean up irq settings during removal mfd: mxs-lradc: Fix error handling in mxs_lradc_probe() mfd: lpc_ich: Avoton/Rangeley uses SPI_BYT method mfd: tps65218: Introduce dependency on CONFIG_OF mfd: tps65218: Correct the config description MAINTAINERS: Fix Dialog search term for watchdog binding file mfd: fsl-imx25: Set irq handler and data in one go mfd: rts5249: Add support for RTS5250S power saving ACPI / PMIC: Add opregion driver for Intel Dollar Cove TI PMIC mfd: Add support for Cherry Trail Dollar Cove TI PMIC syscon: dt-bindings: Add binding document for iProc MHB block syscon: dt-bindings: Add binding doc for Broadcom iProc CDRU mfd: max77693: Add muic of_compatible in mfd_cell mfd: stw481x: Make three arrays static const, reduces object code size mfd: tps65217: Introduce dependency on CONFIG_OF ...
-
Linus Torvalds authored
Merge tag 'char-misc-4.15-rc1' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc Pull char/misc updates from Greg KH: "Here is the big set of char/misc and other driver subsystem patches for 4.15-rc1. There are small changes all over here, hyperv driver updates, pcmcia driver updates, w1 driver updats, vme driver updates, nvmem driver updates, and lots of other little one-off driver updates as well. The shortlog has the full details. All of these have been in linux-next for quite a while with no reported issues" * tag 'char-misc-4.15-rc1' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (90 commits) VME: Return -EBUSY when DMA list in use w1: keep balance of mutex locks and refcnts MAINTAINERS: Update VME subsystem tree. nvmem: sunxi-sid: add support for A64/H5's SID controller nvmem: imx-ocotp: Update module description nvmem: imx-ocotp: Enable i.MX7D OTP write support nvmem: imx-ocotp: Add i.MX7D timing write clock setup support nvmem: imx-ocotp: Move i.MX6 write clock setup to dedicated function nvmem: imx-ocotp: Add support for banked OTP addressing nvmem: imx-ocotp: Pass parameters via a struct nvmem: imx-ocotp: Restrict OTP write to IMX6 processors nvmem: uniphier: add UniPhier eFuse driver dt-bindings: nvmem: add description for UniPhier eFuse nvmem: set nvmem->owner to nvmem->dev->driver->owner if unset nvmem: qfprom: fix different address space warnings of sparse nvmem: mtk-efuse: fix different address space warnings of sparse nvmem: mtk-efuse: use stack for nvmem_config instead of malloc'ing it nvmem: imx-iim: use stack for nvmem_config instead of malloc'ing it thunderbolt: tb: fix use after free in tb_activate_pcie_devices MAINTAINERS: Add git tree for Thunderbolt development ...
-
