The patch removes HTC endpoint tx workers in
favour of direct command submission. This makes a
lot more sense for data path.

mac80211 queues are effectively stopped/woken up
in a more timely fashion preventing build up of
frames. It's possible to push more traffic than
the device/system is able to handle and have no
hiccups or performance degradation with UDP
traffic.

WMI commands will now report errors properly and
possibly block as they actively can wait for tx
credits to become available.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

This will be necessary for further changes in
command submission scheme.

Once HTC is cleaned up WMI commands will finally
block.

This requires for SWBA to be processed in a
non-atomic context for now. Once other necessary
changes are in this will be reverted.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

This will allow higher layers to anticipate and
act upon TX credits renewal. This will be
important for some future rework of WMI command
submission.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

Credit calculation was overly complex
unnecessarily. Now skb dequeing is more unified.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

The driver core clears the driver data to NULL after device_release
or on probe failure. Thus, it is not needed to manually clear the
device driver data to NULL.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

struct ce_sendlist is useless as we always add just one buffer onto it.
And most importantly, it's ugly as it doesn't use skb properly.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

The peer PHY mode for 11ac operation needs to be determined
properly based on the channel bandwidth being used. Fix
this so that the proper mode is given to the firmware.

kvalo: earlier we used 11na-ht20 in STA mode for 11ac AP peer, this
patch changes that to 11ac-vht80. I didn't notice any change in
throughput in my tests, but nevertheless it's the right thing
to do.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

Makes it easier to read debug logs.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

Just to unify with the rest of debug messages. Minimal functional changes,
only major ones are removal of the awkward "else" style in debug
messages.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

To unify the boot debug level.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

To unify the boot debug level.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

To unify all boot related debug messages into one debug
level.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

Fix them to follow the general logging style in ath10k.

While at it, add print id chip_id to the debug log.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

core.c mostly deals with driver and firmware starting related
actions. And we can use the boot level also in other components,
like PCI and HTT.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

Also clean BMI log messages and add few more.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

Otherwise if CONFIG_ATH10K_DEBUGFS won't be set we will
end up with multiple definitions and compilation failure
in each place the header is included.
Signed-off-by: Bartosz Markowski <bartosz.markowski@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

The double while() could end up running forever.
Inner while() would complete very fast. However
the completion processing could take enough time
for more completions to flow in. In that case the
outer while() would not terminate and run again,
and again. This could happen especially on a slow
host system.

This could lead to a system freeze during heavy
traffic. Note: this doesn't solve all known
starvation issues yet.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

There's no functional changes. Just a small cleanup.
Signed-off-by: Bartosz Markowski <bartosz.markowski@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

When configuring the host_interests over BMI, set the UART
baud rate to 19200. This is valid for QCA988X_2.0 devices.

kvalo: found during code review, there should not be any functionality
changes
Signed-off-by: Bartosz Markowski <bartosz.markowski@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

Needed for the HTT stats implementation.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

For analysing various data path statistics in user space.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

The indentation here implies this was meant to be
a multi-statement if, but it lacks the braces.

kvalo: add "ath10k: " prefix
Signed-off-by: Dave Jones <davej@fedoraproject.org>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

So that's it's possible to query chip id from ath10k anytime.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

ath10k doesn't support qca988x hw1.0 boards anymore. Unfortunately
the PCI id is the same in hw1.0 and hw2.0 so ath10k tries to use
hw1.0 boards anyway. But without hw1.0 workarounds in place
ath10k just crashes horribly.

To avoid using hw1.0 boards at all add a chip id detection
and fail the probe if hw1.0 is detected:

[ 5265.786408] ath10k: ERROR: qca988x hw1.0 is not supported
[ 5265.786497] ath10k: Unsupported chip id 0x043200ff
[ 5265.786574] ath10k: could not register driver core (-95)
[ 5265.793191] ath10k_pci: probe of 0000:02:00.0 failed with error -95

Also add a warning if there's an unknown chip id but continue
the boot process normally anyway.
Reported-by: Zaki Bakar <zaki.bm@gmail.com>
Tested-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

ath10k_ce_init() and the functions it calls wakeup
the chip multiple times. Simplify that to call
ath10k_pci_wake() only once. This also makes it
easier to add error handling when wakeup fails.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

We should not try to access hw if wakeup fails so add
proper error checking for that. Also add the timeout lenght
to the warning message.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

The error handling was just weird, simplify it.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

This is consistent with all other functions.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

Void pointers are bad, mmkay.

No functional changes.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

It's easier to read t if the field names are visible.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

It's much more readable if struct entries in host_ce_config_wlan
are explicitly set.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

cacheline_sz is not used anywhere and can be removed.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

The new naming makes more sense.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

The new naming makes more sense.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

The new naming makes more sense.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

Some parameters were unused and are not required.
They have no representation in firmware. Clean
them up.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

It was only written to and never read back. No use
to keep it around.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

Simplifies memory managament of ce_state.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

ath10k_debug_read_target_stats is properly
protected by data_lock (spinlock). Remove
the unwanted mutex_unlock(&ar->conf_mutex)

[ BUG: bad unlock balance detected! ]
-------------------------------------
kworker/u4:0/12459 is trying to release lock
(&ar->conf_mutex) at:
[<c16a170d>] mutex_unlock+0xd/0x10
but there are no more locks to release!

 Call Trace:
  [<c16a170d>] ? mutex_unlock+0xd/0x10
  [<c10b697d>] __lock_release+0x4d/0xe0
  [<f88ca0fc>] ? ath10k_debug_read_target_stats+0xac/0x290

  [<c16a170d>] ? mutex_unlock+0xd/0x10
  [<c10b6a5b>] lock_release+0x4b/0x150
  [<c16a1580>] __mutex_unlock_slowpath+0x70/0x150
  [<f88ca0fc>] ? ath10k_debug_read_target_stats+0xac/0x290

  [<c10b456b>] ? trace_hardirqs_on+0xb/0x10
  [<c16a170d>] mutex_unlock+0xd/0x10
  [<f88ca107>] ath10k_debug_read_target_stats+0xb7/0x290

  [<f88d337a>] ath10k_wmi_event_process+0x3fa/0x6e0

  [<c10b456b>] ? trace_hardirqs_on+0xb/0x10
  [<f88d36e1>] ath10k_wmi_event_work+0x21/0x40
               [ath10k_core]
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>