Adapt the tg3 driver to use the reworked PCI PM and make it use the
exported PCI PM core functions instead of accessing the PCI PM registers
directly by itself.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Fix direct casts of pointers to u32 in the InterPhase ATM driver.  These are
all arguments being passed to printk() calls.  So drop the cast and change the
%x to a %p.
Signed-off-by: David Howells <dhowells@redhat.com>
Acked-by: Chas Williams <chas@cmf.nrl.navy.mil>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Fix const assignment/discard warnings in the ATM networking driver.

The lane2_assoc_ind() function needed its arguments changing to match changes
in the lane2_ops struct (patch 61c33e01
"atm: use const where reasonable").
Signed-off-by: David Howells <dhowells@redhat.com>
Acked-by: Chas Williams <chas@cmf.nrl.navy.mil>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

The rationale is:
   * use u32 consistently
   * no need to do LCG on values from (better) get_random_bytes
   * use more data from get_random_bytes for secondary seeding
   * don't reduce state space on srandom32()
   * enforce state variable initialization restrictions

Note: the second paper has a version of random32() with even longer period
and a version of random64() if needed.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>

When bridging interfaces with different MTUs, the bridge correctly chooses
the minimum of the MTUs of the physical devices as the bridges MTU.  But
when a frame is passed which fits through the incoming, but not through
the outgoing interface, a "Fragmentation Needed" packet is generated.

However, the propagated MTU is hardcoded to 1500, which is wrong in this
situation.  The sender will repeat the packet again with the same frame
size, and the same problem will occur again.

Instead of sending 1500, the (correct) MTU value of the bridge is now sent
via PMTU.  To achieve this, the corresponding rtable structure is stored
in its net_bridge structure.

Modified to get rid of fake_net_device as well.
Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

The mutex is released on a successful return, so it would seem that it
should be released on an error return as well.

The semantic patch finds this problem is as follows:
(http://www.emn.fr/x-info/coccinelle/)

// <smpl>
@@
expression l;
@@

mutex_lock(l);
... when != mutex_unlock(l)
    when any
    when strict
(
if (...) { ... when != mutex_unlock(l)
+   mutex_unlock(l);
    return ...;
}
|
mutex_unlock(l);
)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

SH7763 has Ethernet core same as SH7710/SH7712.
Positions of some registry are different, but the basic part is the same.
I add support of ethernet of sh7763 to sh_eth.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

Trying to build with CONFIG_NE2000=m fails with:

  scripts/mod/modpost   -o /tmp/tmp/linux-2.6.27-rc1/Module.symvers    -S     -s
ERROR: "NS8390_init" [drivers/net/ne.ko] undefined!

This is because the split of 8390 into pausing and non-pausing
versions was incompletely propagated to ne.c. This fixes it.
Signed-off-by: Mikael Pettersson <mikpe@it.uu.se>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

Use a menuconfig directive to make all of networking support one-click
deselectable from the top-level menu.
Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>

This call is no longer needed, sockstat6 is per namespace so it is
removed at the namespace subsystem destruction.
Signed-off-by: Daniel Lezcano <dlezcano@fr.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

From a report by Matti Aarnio, and preliminary patch by Adam Langley.
Signed-off-by: David S. Miller <davem@davemloft.net>

Bug report from Steven Jan Springl:

	Issuing the following command causes a kernel oops:
		tc qdisc add dev eth0 handle ffff: ingress

The problem mostly stems from all of the special case handling of
ingress qdiscs.

So, to fix this, do the grafting operation the same way we do for TX
qdiscs.  Which means that dev_activate() and dev_deactivate() now do
the "qdisc_sleeping <--> qdisc" transitions on dev->rx_queue too.

Future simplifications are possible now, mainly because it is
impossible for dev_queue->{qdisc,qdisc_sleeping} to be NULL.  There
are NULL checks all over to handle the ingress qdisc special case
that used to exist before this commit.
Signed-off-by: David S. Miller <davem@davemloft.net>

From: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

dm_{read,write}() were doing USB transfers of data on stack, which isn't
allowed. Fix it by kmalloc'ing a temporary buffer.
Clean up the error handling for short transfers while we're at it.
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

The callers of niu_ethflow_to_class expect zero as error, but it returns
-1 instead.
Signed-off-by: Andreas Schwab <schwab@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

When an error occured, datagram_send_ctl() should exit immediately rather than
continue to run the for loop. Otherwise, the variable err might be changed and
the error might be hidden.

Fix this bug by using "goto" instead of "break".
Signed-off-by: Miao Xie <miaox@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

On s2io driver, when you change the interface MTU, it invokes a card
reset, which flush some statistics.  This patch solves this problem, and
also set the net_device->stats as the default statistics structure,
instead of s2io_nic->stats.

To do that, s2io_nic->stats turned into a staging area, where is saved
statistics of the last hardware statistics query. So, the difference
between the current hardware statistics and s2io_nic->stats, is the
value that should be summed up, in order to get the correct statistics
value, even after a reset.
Signed-off-by: Breno Leitao <leitao@linux.vnet.ibm.com>
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

Recent changes to the IRQ framework have made passing the wrong
trigger type to request_irq() become a fatal error.  In the case
of the enc28j60 driver, it stopped working in my test harness.

(Specifically:  the signal detects "pin change" events, both edges,
not just falling edges.  Similarly, other boards might route it
through an inverter.  Trigger type are board-specific.)

This fixes that problem by the usual fix of expecting board setup
code to have set up the correct IRQ trigger type.  The best known
example of that being x86 setup.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

skb->dev is set by eth_type_trans already.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

Starting with FW version 7.0, the driver needs to allow larger images.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

Reprogram MAC address after resume from Suspend Mem
(Blackfin Hibernate looses all CORE and SYSTEM register content)
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

Signed-off-by: Bryan Wu <cooloney@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

Signed-off-by: Mike Frysinger <vapier.adi@gmail.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

This patch adds support for the realtek 8211c phy. The driver must
perform a hardware reset of the phy due to an errata where the phy could
not detect the link.
Signed-off-by: Ayaz Abdulla <aabdulla@nvidia.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

This patch fixes mesh beaconing, which was broken by "mac80211: revamp
beacon configuration".
Signed-off-by: Luis Carlos Cobo <luisca@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

The semantic patch I used was this:

@@
expression lock;
identifier flags;
expression subclass;
@@

- unsigned int flags;
+ unsigned long flags;

...

<+...

(
 spin_lock_irqsave(lock, flags)
|
 _spin_lock_irqsave(lock)
|
 spin_unlock_irqrestore(lock, flags)
|
 _spin_unlock_irqrestore(lock, flags)
|
 read_lock_irqsave(lock, flags)
|
 _read_lock_irqsave(lock)
|
 read_unlock_irqrestore(lock, flags)
|
 _read_unlock_irqrestore(lock, flags)
|
 write_lock_irqsave(lock, flags)
|
 _write_lock_irqsave(lock)
|
 write_unlock_irqrestore(lock, flags)
|
 _write_unlock_irqrestore(lock, flags)
|
 spin_lock_irqsave_nested(lock, flags, subclass)
|
 _spin_lock_irqsave_nested(lock, subclass)
|
 spin_unlock_irqrestore(lock, flags)
|
 _spin_unlock_irqrestore(lock, flags)
|
 _raw_spin_lock_flags(lock, flags)
|
 __raw_spin_lock_flags(lock, flags)
)

...+>

This patch was generated using the Coccinelle framework.

Cc: Masakazu Mokuno <mokuno@sm.sony.co.jp>
Cc: Julia Lawall <julia@diku.dk>
Cc: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Vegard Nossum <vegard.nossum@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

The master interface is a virtual interface that is registered
to mac80211, changing that does not seem like a good idea at
the moment. However, since it has no sdata, we cannot accept
any configuration for it. This patch makes the cfg80211 hooks
reject any such attempt.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Julius Volz pointed out that the dump callbacks in nl80211 were
broken and fixed one of them. This patch fixes the other three
and also addresses the TODOs there.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Cc: Julius Volz <juliusv@google.com>
Cc: Thomas Graf <tgraf@suug.ch>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This patch fixes mac80211 to not use the skb->cb over the queue step
from virtual interfaces to the master. The patch also, for now,
disables aggregation because that would still require requeuing,
will fix that in a separate patch. There are two other places (software
requeue and powersaving stations) where requeue can happen, but that is
not currently used by any drivers/not possible to use respectively.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Wireless statistics produced by the RTL8187B driver are not particularly
informative about the strength of the received signal. From the data sheet
provided by Realtek, I discovered that certain parts of the RX header
should have the information necessary to calculate signal quality and
strength. With testing, it became clear that most of these quantities were
very jittery - only the AGC correlated with the signals expected from nearby
AP's. As a result, the quality and strength are derived from the agc value.
The scaling has been determined so that the numbers are close to those
obtained by b43 under the same conditions. The results are qualitatively
correct.

Statistics derived for the RTL8187 have not been changed.

The RX header variables have been renamed to match the quantites described
in the Realtek data sheet.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

"mac80211: fix TX sequence numbers" broke rtl8187. This
patch makes the same kind of fix that was done for rt2x00. Note that
this code will have to be reworked for proper sequence numbers on beacons.
In addition, the sequence number has been placed in the hardware state,
not the vif state.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

In net/mac80211/tx.c, there are some #ifdef which checks
MAC80211_VERBOSE_PS_DEBUG
(which in fact is never set) instead of
CONFIG_MAC80211_VERBOSE_PS_DEBUG, as should be.

This patch replaces MAC80211_VERBOSE_PS_DEBUG with
CONFIG_MAC80211_VERBOSE_PS_DEBUG in these #ifdef commands in
net/mac80211/tx.c.
Signed-off-by: Rami Rosen <ramirose@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

drivers/net/wireless/mac80211_hwsim.c:503:20: warning: Using plain integer as NULL pointer
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ia64:

drivers/net/wireless/iwlwifi/iwl-led.c: In function `iwl_get_blink_rate':
drivers/net/wireless/iwlwifi/iwl-led.c:271: warning: long long int format, s64 arg (arg 6)
drivers/net/wireless/iwlwifi/iwl-led.c:271: warning: long long int format, u64 arg (arg 7)

We do not know what type the architecture uses to impement u64 and s64,
hence we must cast the variables for printing.

Cc: Tomas Winkler <tomas.winkler@intel.com>
Cc: John W. Linville <linville@tuxdriver.com>
Cc: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Return the proper error code rather than a hard-coded ENOMEM from
ieee80211_wep_init.  Also, print the error code on failure.
Signed-off-by: Jeremy Fitzhardinge <jeremy@goop.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Use dev_kfree_skb_any(); instead of dev_kfree_skb();, since
ieee80211_beacon_get function might be called from atomic.
(It's in a fail path.)
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Cc: Johannes Berg <johannes@sipsolutions.net>
Cc: Michael Wu <flamingice@sourmilk.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>