This dependency was added because ipv6_find_hdr was in iptables specific
code but is no longer required

Fixes: f8f62675 ("ipv6: Move ipv6_find_hdr() out of Netfilter code.")
Fixes: 63dca2c0 ("ipvs: Fix faulty IPv6 extension header handling in IPVS")
Signed-off-by: Yaroslav Bolyukin <iam@lach.pw>
Acked-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>

Add NFT_SOCKET_WILDCARD to match to wildcard socket listener.
Signed-off-by: Balazs Scheidler <bazsi77@gmail.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>

Use ip_is_fragment() to simpify code.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>

We can delay refcount increment until we reassign the existing entry to
the current skb.

A 0 refcount can't happen while the nf_conn object is still in the
hash table and parallel mutations are impossible because we hold the
bucket lock.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>

There is a misconception about what "insert_failed" means.

We increment this even when a clash got resolved, so it might not indicate
a problem.

Add a dedicated counter for clash resolution and only increment
insert_failed if a clash cannot be resolved.

For the old /proc interface, export this in place of an older stat
that got removed a while back.
For ctnetlink, export this with a new attribute.

Also correct an outdated comment that implies we add a duplicate tuple --
we only add the (unique) reply direction.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>

This counter increments when nf_conntrack_in sees a packet that already
has a conntrack attached or when the packet is marked as UNTRACKED.
Neither is an error.

The former is normal for loopback traffic.  The second happens for
certain ICMPv6 packets or when nftables/ip(6)tables rules are in place.

In case someone needs to count UNTRACKED packets, or packets
that are marked as untracked before conntrack_in this can be done with
both nftables and ip(6)tables rules.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>

The /proc interface for nf_conntrack displays the "error" counter as
"icmp_error".

It makes sense to not increment "invalid" when failing to handle an icmp
packet since those are special.

For example, its possible for conntrack to see partial and/or fragmented
packets inside icmp errors.  This should be a separate event and not get
mixed with the "invalid" counter.

Likewise, remove the "error" increment for errors from get_l4proto().
After this, the error counter will only increment for errors coming from
icmp(v6) packet handling.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>

Enables storing userdata for nft_table. Field udata points to user data
and udlen store its length.

Adds new attribute flag NFTA_TABLE_USERDATA
Signed-off-by: Jose M. Guisado Gomez <guigom@riseup.net>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>

do_ip_vs_set_ctl() is referencing uninitialized stack value when `len` is
zero. Fix it.

Reported-by: syzbot+23b5f9e7caf61d9a3898@syzkaller.appspotmail.com
Link: https://syzkaller.appspot.com/bug?id=46ebfb92a8a812621a001ef04d90dfa459520fe2Suggested-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: Peilin Ye <yepeilin.cs@gmail.com>
Acked-by: Julian Anastasov <ja@ssi.bg>
Reviewed-by: Simon Horman <horms@verge.net.au>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>

Detect and rewrite a prefix embedded in an ICMPv6 original packet that was
rewritten by a corresponding DNPT/SNPT rule so it will be recognised by
the host that sent the original packet.

Example

Rules in effect on the 1:2:3:4::/64 + 5:6:7:8::/64 side router:
* SNPT src-pfx 1:2:3:4::/64 dst-pfx 5:6:7:8::/64
* DNPT src-pfx 5:6:7:8::/64 dst-pfx 1:2:3:4::/64

No rules on the 9:a:b:c::/64 side.

1. 1:2:3:4::1 sends UDP packet to 9:a:b:c::1
2. Router applies SNPT changing src to 5:6:7:8::ffef::1
3. 9:a:b:c::1 receives packet with (src 5:6:7:8::ffef::1 dst 9:a:b:c::1)
	and replies with ICMPv6 port unreachable to 5:6:7:8::ffef::1,
	including original packet (src 5:6:7:8::ffef::1 dst 9:a:b:c::1)
4. Router forwards ICMPv6 packet with (src 9:a:b:c::1 dst 5:6:7:8::ffef::1)
	including original packet (src 5:6:7:8::ffef::1 dst 9:a:b:c::1)
	and applies DNPT changing dst to 1:2:3:4::1
5. 1:2:3:4::1 receives ICMPv6 packet with (src 9:a:b:c::1 dst 1:2:3:4::1)
	including original packet (src 5:6:7:8::ffef::1 dst 9:a:b:c::1).
	It doesn't recognise the original packet as the src doesn't
	match anything it originally sent

With this change, at step 4, DNPT will also rewrite the original packet
src to 1:2:3:4::1, so at step 5, 1:2:3:4::1 will recognise the ICMPv6
error and provide feedback to the application properly.

Conversely, SNPT will help when ICMPv6 errors are sent from the
translated network.

1. 9:a:b:c::1 sends UDP packet to 5:6:7:8::ffef::1
2. Router applies DNPT changing dst to 1:2:3:4::1
3. 1:2:3:4::1 receives packet with (src 9:a:b:c::1 dst 1:2:3:4::1)
	and replies with ICMPv6 port unreachable to 9:a:b:c::1
	including original packet (src 9:a:b:c::1 dst 1:2:3:4::1)
4. Router forwards ICMPv6 packet with (src 1:2:3:4::1 dst 9:a:b:c::1)
	including original packet (src 9:a:b:c::1 dst 1:2:3:4::1)
	and applies SNPT changing src to 5:6:7:8::ffef::1
5. 9:a:b:c::1 receives ICMPv6 packet with
	(src 5:6:7:8::ffef::1 dst 9:a:b:c::1) including
	original packet (src 9:a:b:c::1 dst 1:2:3:4::1).
	It doesn't recognise the original packet as the dst doesn't
	match anything it already sent

The change to SNPT means the ICMPv6 original packet dst will be
rewritten to 5:6:7:8::ffef::1 in step 4, allowing the error to be
properly recognised in step 5.
Signed-off-by: Michael Zhou <mzhou@cse.unsw.edu.au>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>

Commit d3b990b7 ("netlabel: fix problems with mapping removal")
added a check to return an error if ret_val != 0, before ret_val is
later used in a log message. Now it will unconditionally print "...
res=1". So just drop the check.

Addresses-Coverity: ("Dead code")
Fixes: d3b990b7 ("netlabel: fix problems with mapping removal")
Signed-off-by: Alex Dewar <alex.dewar90@gmail.com>
Acked-by: Paul Moore <paul@paul-moore.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Shannon Nelson says:

====================
ionic memory usage rework

Previous review comments have suggested [1],[2] that this driver
needs to rework how queue resources are managed and reconfigured
so that we don't do a full driver reset and to better handle
potential allocation failures.  This patchset is intended to
address those comments.

The first few patches clean some general issues and
simplify some of the memory structures.  The last 4 patches
specifically address queue parameter changes without a full
ionic_stop()/ionic_open().

[1] https://lore.kernel.org/netdev/20200706103305.182bd727@kicinski-fedora-pc1c0hjn.dhcp.thefacebook.com/
[2] https://lore.kernel.org/netdev/20200724.194417.2151242753657227232.davem@davemloft.net/

v3: use PTR_ALIGN without typecast
    fix up Neel's attribution

v2: use PTR_ALIGN
    recovery if netif_set_real_num_tx/rx_queues fails
    less racy queue bring up after reconfig
    common-ize the reconfig queue stop and start
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Convert tx_timeout handler to not do the full reset.  As this was
the last user of ionic_reset_queues(), we can drop it.
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add to our new ionic_reconfigure_queues() to also be able to change
the number of queues in use, and to change the queue interrupt layout
between split and combined.
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>

The original way of changing ring length was to completely
tear down the lif's queue structure and then rebuild it, while
running the risk of allocations that might fail in the middle
and leave us with a broken driver.

Instead, we can set up all the new queue and descriptor
allocations first, then swap them out and delete the old
allocations.  If the new allocations fail, we report the error,
stay with the old setup and continue running.  This gives us
a safer path, and a smaller window of time where we're not
processing traffic.
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>

We really don't need to tear down and rebuild the whole queue structure
when changing the MTU; we can simply stop the queues, clean and refill,
then restart the queues.
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>

Use index counters rather than pointers for tracking head
and tail in the queues to save a little memory and to perhaps
slightly faster queue processing.
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>

Split out the queue descriptor blocks into separate dma
allocations to make for smaller blocks.
Co-developed-by: Neel Patel <neel@pensando.io>
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>

ionic_open() and ionic_stop() are not referenced outside of their
defining file, so make them static.
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>

Use a block of stats structs attached to the lif instead of
little ones attached to each qcq.  This simplifies our memory
management and gets rid of a lot of unnecessary indirection.
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>

As we aren't yet supporting multiple lifs, we can remove
complexity by removing the list concept and related code,
to be re-engineered later when actually needed.
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>

Use kcalloc for allocating arrays of structures.

Following along after
commit e71642009cbdA ("ionic_lif: Use devm_kcalloc() in ionic_qcq_alloc()")
there are a couple more array allocations that can be converted
to using devm_kcalloc().
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>

Fix the queue name displayed.
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>

The NIC might tell us its minimum MTU, but let's be sure not
to use something smaller than ETH_MIN_MTU.
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>

Dan Murphy says:

====================
Enable Fiber on DP83822 PHY

The DP83822 Ethernet PHY has the ability to connect via a Fiber port.  The
derivative PHYs DP83825 and DP83826 do not have this ability. In fiber mode
the DP83822 disables auto negotiation and has a fixed 100Mbps speed with
support for full or half duplex modes.

A devicetree binding was added to set the signal polarity for the fiber
connection.  This property is only applicable if the FX_EN strap is set in
hardware other wise the signal loss detection is disabled on the PHY.

If the FX_EN is not strapped the device can be configured to run in fiber mode
via the device tree. All be it the PHY will not perform signal loss detection.

v2 review from a long time ago can be found here - https://lore.kernel.org/patchwork/patch/1270958/
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

The DP83822 can be configured to use a Fiber connection.  The strap
register is read to determine if the device has been configured to use
a fiber connection.  With the fiber connection the PHY can be configured
to detect whether the fiber connection is active by either a high signal
or a low signal.

Fiber mode is only applicable to the DP83822 so rework the PHY match
table so that non-fiber PHYs can still use the same driver but not call
or use any of the fiber features.
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add a dt binding for the TI dp83822 ethernet phy device.
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

The sysctl that was added  earlier by commit 79134e6c ("net: do
not create fallback tunnels for non-default namespaces") to create
fall-back only in root-ns. This patch enhances that behavior to provide
option not to create fallback tunnels in root-ns as well. Since modules
that create fallback tunnels could be built-in and setting the sysctl
value after booting is pointless, so added a kernel cmdline options to
change this default. The default setting is preseved for backward
compatibility. The kernel command line option of fb_tunnels=initns will
set the sysctl value to 1 and will create fallback tunnels only in initns
while kernel cmdline fb_tunnels=none will set the sysctl value to 2 and
fallback tunnels are skipped in every netns.
Signed-off-by: Mahesh Bandewar <maheshb@google.com>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Maciej Zenczykowski <maze@google.com>
Cc: Jian Yang <jianyang@google.com>
Cc: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Andre Edich says:

====================
Add phylib support to smsc95xx

To allow to probe external PHY drivers, this patch series adds use of
phylib to the smsc95xx driver.

Changes in v5:
- Removed all phy_read calls from the smsc95xx driver.

Changes in v4:
- Removed useless inline type qualifier.

Changes in v3:
- Moved all MDI-X functionality to the corresponding phy driver;
- Removed field internal_phy from a struct smsc95xx_priv;
- Initialized field is_internal of a struct phy_device;
- Kconfig: Added selection of PHYLIB and SMSC_PHY for USB_NET_SMSC95XX.

Changes in v2:
- Moved 'net' patches from here to the separate patch series;
- Removed redundant call of the phy_start_aneg after phy_start;
- Removed netif_dbg tracing "speed, duplex, lcladv, and rmtadv";
- mdiobus: added dependency from the usbnet device;
- Moved making of the MII address from 'phy_id' and 'idx' into the
  function mii_address;
- Moved direct MDIO accesses under condition 'if (pdata->internal_phy)',
  as they only need for the internal PHY;
- To be sure, that this set of patches is git-bisectable, tested each
  sub-set of patches to be functional for both, internal and external
  PHYs, including suspend/resume test for the 'devices'
  (5.7.8-1-ARCH, Raspberry Pi 3 Model B).
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Generally, each PHY has their own configuration and it can be done
through an external PHY driver.  The smsc95xx driver uses only the
hard-coded internal PHY configuration.

This patch adds phylib support to probe external PHY drivers for
configuring external PHYs.

The MDI-X configuration for the internal PHYs moves from
drivers/net/usb/smsc95xx.c to drivers/net/phy/smsc.c.
Signed-off-by: Andre Edich <andre.edich@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Using `void *driver_priv` instead of `unsigned long data[]` is more
straightforward way to recover the `struct smsc95xx_priv *` from the
`struct net_device *`.
Signed-off-by: Andre Edich <andre.edich@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch removes arguments netdev and phy_id from the functions
smsc95xx_mdio_read_nopm and smsc95xx_mdio_write_nopm.  Both removed
arguments are recovered from a new argument `struct usbnet *dev`.
Signed-off-by: Andre Edich <andre.edich@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge tag 'mac80211-next-for-davem-2020-08-28' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next

Johannes Berg says:

====================
This time we have:
 * some code to support SAE (WPA3) offload in AP mode
 * many documentation (wording) fixes/updates
 * netlink policy updates, including the use of NLA_RANGE
   with binary attributes
 * regulatory improvements for adjacent frequency bands
 * and a few other small additions/refactorings/cleanups
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Like all other network functions, let's notify gtp context on creation and
deletion.
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Tested-by: Gabriel Ganne <gabriel.ganne@6wind.com>
Acked-by: Harald Welte <laforge@gnumonks.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Julian Wiedmann says:

====================
s390/qeth: updates 2020-08-27

please apply the following patch series for qeth to netdev's net-next tree.

Patch 8 makes some improvements to how we handle HW address events,
avoiding some uncertainty around processing stale events after we
switched off the feature.
Except for that it's all straight-forward cleanups.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

The current code for bridge address events has two shortcomings in its
control sequence:

1. after disabling address events via PNSO, we don't flush the remaining
   events from the event_wq. So if the feature is re-enabled fast
   enough, stale events could leak over.
2. PNSO and the events' arrival via the READ ccw device are unordered.
   So even if we flushed the workqueue, it's difficult to say whether
   the READ device might produce more events onto the workqueue
   afterwards.

Fix this by
1. explicitly fencing off the events when we no longer care, in the
   READ device's event handler. This ensures that once we flush the
   workqueue, it doesn't get additional address events.
2. Flush the workqueue after disabling the events & fencing them off.
   As the code that triggers the flush will typically hold the sbp_lock,
   we need to rework the worker code to avoid a deadlock here in case
   of a 'notifications-stopped' event. In case of lock contention,
   requeue such an event with a delay. We'll eventually aquire the lock,
   or spot that the feature has been disabled and the event can thus be
   discarded.

This leaves the theoretical race that a stale event could arrive
_after_ we re-enabled ourselves to receive events again. Such an event
would be impossible to distinguish from a 'good' event, nothing we can
do about it.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Reviewed-by: Alexandra Winter <wintera@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The data returned from IPA_SBP_QUERY_BRIDGE_PORTS and
IPA_SBP_BRIDGE_PORT_STATE_CHANGE has the same format. Use a single
struct definition for it.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Reviewed-by: Alexandra Winter <wintera@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Current code copies _all_ entries from the event into a worker, when we
later only need specific data from the first entry.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Reviewed-by: Alexandra Winter <wintera@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The only time that our Bridgeport role should change is when we change
the configuration ourselves. In which case we also adjust our internal
state tracking, no need to do it again when we receive the corresponding
event.

Removing the locked section helps a subsequent patch that needs to flush
the workqueue while under sbp_lock.

It would be nice to raise a warning here in case HW does weird things
after all, but this could end up generating false-positives when we
change the configuration ourselves.
Suggested-by: Alexandra Winter <wintera@linux.ibm.com>
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Reviewed-by: Alexandra Winter <wintera@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

A newly initialized device is disabled for address events, there's no
need to explicitly disable them.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Reviewed-by: Alexandra Winter <wintera@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>