Add PSCI support to enable suspend/resume with the help of TF-A.
Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20240208135629.2840932-3-claudiu.beznea.uj@bp.renesas.comSigned-off-by: Geert Uytterhoeven <geert+renesas@glider.be>

Ethernet IRQ GPIOs are marked as GPIO hogs.  Thus, these GPIOs are
requested at probe time without considering if there are other
peripherals that need them.  The Ethernet IRQ GPIOs are shared with
SDHI2.  Selection between Ethernet and SDHI2 is done through a hardware
switch.  To avoid scenarios where one wants to boot with SDHI2 support
and some SDHI pins are not propertly configured because of the GPIO
hogs, guard the Ethernet IRQ GPIO hogs with the proper build flag.

Fixes: 932ff0c8 ("arm64: dts: renesas: rzg3s-smarc-som: Enable the Ethernet interfaces")
Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20240208124300.2740313-13-claudiu.beznea.uj@bp.renesas.comSigned-off-by: Geert Uytterhoeven <geert+renesas@glider.be>

The IRQC block on the RZ/G3S (R9A08G045) SoC supports ECCRAM error
interrupts too.  Add those missing interrupts to the IRQC node.

Fixes: 837918aa ("arm64: dts: renesas: r9a08g045: Add IA55 interrupt controller node")
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20240205144421.51195-4-prabhakar.mahadev-lad.rj@bp.renesas.comSigned-off-by: Geert Uytterhoeven <geert+renesas@glider.be>

The IRQC IP block supports Bus error and ECCRAM interrupts on RZ/G2L and
alike SoC's (listed below).  Update the IRQC nodes with the missing
interrupts, and additionally, include the 'interrupt-names' properties
in the IRQC nodes so that the driver can parse interrupts by name.

  - R9A07G043U              - RZ/G2UL
  - R9A07G044L/R9A07G044LC  - RZ/{G2L,G2LC}
  - R9A07G054               - RZ/V2L

Fixes: 5edc51af ("arm64: dts: renesas: r9a07g044: Add IRQC node")
Fixes: 48ab6edd ("arm64: dts: renesas: r9a07g043u: Add IRQC node")
Fixes: 379478ab ("arm64: dts: renesas: r9a07g054: Add IRQC node")
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20240205144421.51195-3-prabhakar.mahadev-lad.rj@bp.renesas.comSigned-off-by: Geert Uytterhoeven <geert+renesas@glider.be>

Add operating points for running the Cortex-A76 CPU cores on R-Car V4M
at various speeds, up to the Normal (1.0 GHz).
Signed-off-by: Duy Nguyen <duy.nguyen.rh@renesas.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/736b5836ec2b54e8b36712866309dc1b7ee1fc48.1706796979.git.geert+renesas@glider.be

Describe the clocks for the four Cortex-A76 CPU cores.
CA76 CPU cores 0,1,2,3 are clocked by ZC0,ZC1,ZC2,ZC3.
Signed-off-by: Duy Nguyen <duy.nguyen.rh@renesas.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/c64cf6ca1590fa1a36b90a18fd70c831d5b8318e.1706796979.git.geert+renesas@glider.be

Support CPUIdle for ARM Cortex-A76 on R-Car V4M.
Signed-off-by: Duy Nguyen <duy.nguyen.rh@renesas.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/848d176bdbcaf3bc44e5dae555afa9c812a19fd1.1706796979.git.geert+renesas@glider.be

Complete the description of the Cortex-A76 CPU cores and L3 cache
controllers on the Renesas R-Car V4M (R8A779H0) SoC, including CPU
topology and PSCI support for enabling CPU cores.
Signed-off-by: Duy Nguyen <duy.nguyen.rh@renesas.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/c2a38a0da74915bf2a9171e53886c83a1c732934.1706796979.git.geert+renesas@glider.be

Describe the cache configuration for the first Cortex-A76 CPU core on
the Renesas R-Car V4M (R8A779H0) SoC.
Signed-off-by: Duy Nguyen <duy.nguyen.rh@renesas.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/9d56a46892c5e0957d244370e6809013cf815905.1706796979.git.geert+renesas@glider.be

Add device nodes for the General Purpose Input/Output (GPIO) blocks on
the Renesas R-Car V4M (R8A779H0) SoC.
Signed-off-by: Cong Dang <cong.dang.xn@renesas.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/d4c1c40404ab84c7e7c07612077ca1a319ae7283.1706796918.git.geert+renesas@glider.be

Enable the I2C0 bus on the Gray Hawk Single board, and describe the I2C
EEPROMs present.

Based on patches for Gray Hawk in the BSP by Hai Pham.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/960595394a274b675f1ec9ec1c324e4cc1ac1f77.1706796660.git.geert+renesas@glider.be

Add device nodes for the I2C Bus Interfaces on the Renesas R-Car V4M
(R8A779H0) SoC.
Signed-off-by: Hai Pham <hai.pham.ud@renesas.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/7dbbe13428273c5786ddff6ea7af6724fcdd4de8.1706796660.git.geert+renesas@glider.be

Sound uses the standard 5V supply, so rename the fixed regulator as
such. Also add properties documenting it is always on, also during boot.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20240129212350.33370-3-wsa+renesas@sang-engineering.comSigned-off-by: Geert Uytterhoeven <geert+renesas@glider.be>

It is named T1.8V in the schematics. Also add properties documenting it
is always on, also during boot.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20240129212350.33370-2-wsa+renesas@sang-engineering.comSigned-off-by: Geert Uytterhoeven <geert+renesas@glider.be>

Without them, no power, so cards do not get recognized.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20240129135840.28988-1-wsa+renesas@sang-engineering.comSigned-off-by: Geert Uytterhoeven <geert+renesas@glider.be>

Complete the descriptions of the serial console and the external serial
clock by adding pin control.

Based on patches for Gray Hawk in the BSP by Hai Pham and Nghia Nguyen.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/b1eb2d3364d5ead7f7bcf7a737c5914971db64d3.1706266286.git.geert+renesas@glider.be

Add a device node for the Pin Function Controller on the Renesas R-Car
V4M (R8A779H0) SoC.
Signed-off-by: Hai Pham <hai.pham.ud@renesas.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/0ab32290014b64ddbee5c9ec2808c8294d0b6192.1706266286.git.geert+renesas@glider.be

Enable the watchdog timer on the Gray Hawk Single board.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/cf6effafd9e0472a457eed9d84a834abc3e1c833.1706790320.git.geert+renesas@glider.be

Add a device node for the RCLK Watchdog Timer (RWDT) on the Renesas
R-Car V4M (R8A779H0) SoC.
Signed-off-by: Minh Le <minh.le.aj@renesas.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/43bb03f3baa87b4be8ce953b1955df6b89387e4c.1706790320.git.geert+renesas@glider.be

Add the input capture interrupt on Timer Unit instances that have it.
Add "interrupt-names" properties for clarity.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/5c70ad8c2ea14333616c5add31a4a958f4a47081.1705325654.git.geert+renesas@glider.be

Add the input capture interrupt on Timer Unit instances that have it.
Add "interrupt-names" properties for clarity.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/389a18ee2cea96726462c28463cf212330f74ee3.1705325654.git.geert+renesas@glider.be

Add CSI and CRU nodes r9a07g043 (RZ/G2UL) SoC DTSI.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20240126133116.121981-4-biju.das.jz@bp.renesas.comSigned-off-by: Geert Uytterhoeven <geert+renesas@glider.be>

Add initial support for the Renesas Gray Hawk Single board, which is
based on the R-Car V4M (R8A779H0) SoC:
  - Memory,
  - Crystal oscillators,
  - Serial console.

Based on the White Hawk Single DTS, and on a patch for the Gray Hawk
board stack in the BSP by Hai Pham.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Link: https://lore.kernel.org/r/b657402113267acd57aece0b4c681b707e704455.1706194617.git.geert+renesas@glider.be

Add initial support for the Renesas R-Car V4M (R8A779H0) SoC.
Signed-off-by: Hai Pham <hai.pham.ud@renesas.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Link: https://lore.kernel.org/r/4107bc3d7c31932da29e671ddf4b1564ba38a84c.1706194617.git.geert+renesas@glider.be

Renesas R-Car V4M DT Binding Definitions

Clock and Power Domain definitions for the Renesas R-Car V4M (R8A779H0)
SoC, shared by driver and DT source files.

Enable the watchdog interface (accessible by Cortex-A of RZ/G3S SoC) on
RZ/G3S SMARC SoM.
Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20240122111115.2861835-11-claudiu.beznea.uj@bp.renesas.comSigned-off-by: Geert Uytterhoeven <geert+renesas@glider.be>

Add the DT node for the watchdog IP accessible by Cortex-A of RZ/G3S
SoC (R9108G045).
Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20240122111115.2861835-10-claudiu.beznea.uj@bp.renesas.comSigned-off-by: Geert Uytterhoeven <geert+renesas@glider.be>

R-Car V4H actually has two SCIF_CLK pins.
The second pin provides the SCIF_CLK signal for HSCIF2 and SCIF4.

Fixes: a4c31c56 ("arm64: dts: renesas: r8a779g0: Add SCIF nodes")
Fixes: 39d9dfc6 ("arm64: dts: renesas: r8a779g0: Add remaining HSCIF nodes")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/72f20c1bf32187bd30a963cafe27252907d661f9.1705589612.git.geert+renesas@glider.be

Add all Clock Pulse Generator Core Clock Outputs for the Renesas R-Car
V4M (R8A779H0) SoC.
Signed-off-by: Duy Nguyen <duy.nguyen.rh@renesas.com>
Signed-off-by: Hai Pham <hai.pham.ud@renesas.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/11acbd2a30b58607474e9c32eb798b3a00e85e73.1706194617.git.geert+renesas@glider.be

Document support for the Clock Pulse Generator (CPG) and Module Standby
Software Reset (MSSR) module on the Renesas R-Car V4M (R8A779H0) SoC.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/eb3cd02b62f3ca834df079a3f1e551d9414fe42a.1706194617.git.geert+renesas@glider.be

Add power domain indices for the Renesas R-Car V4M (R8A779H0) SoC.
Signed-off-by: Duy Nguyen <duy.nguyen.rh@renesas.com>
Signed-off-by: Hai Pham <hai.pham.ud@renesas.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/c5cbef71178cada761e9da7bcbb6f21334f93ef8.1706194617.git.geert+renesas@glider.beSigned-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Document support for the System Controller (SYSC) in the R-Car V4M
(R8A779H0) SoC.
Signed-off-by: Duy Nguyen <duy.nguyen.rh@renesas.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/6315cbd0b6e9b92a7914d98f397a2c663ad521c6.1706194617.git.geert+renesas@glider.beSigned-off-by: Ulf Hansson <ulf.hansson@linaro.org>

The White Hawk Single board is a single-board integration of the Renesas
White Hawk CPU and Breakout board stack, based on the R-Car V4H ES2.0
(R8A779G2) SoC.

For now, the only visible differences compared to the board stack are:
  - The SoC is an updated version of R-Car V4H (R8A779G0),
  - The serial console uses an FT2232H instead of a CP2102 USB-UART
    bridge, with CTS/RTS wired.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/2b8d37949c17cca170c1d9e97f10a100b20c5cd9.1706192990.git.geert+renesas@glider.be

Add support for the Renesas R-Car V4H ES2.0 (R8A779G2) SoC, which is an
updated version of the R-Car V4H (R8A779G0) SoC.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/4f773dbb66af5da51d1e171424ec8f97ee933b36.1706192990.git.geert+renesas@glider.be

Factor out the parts on the White Hawk BreakOut board that are also
present on the White Hawk Single board, so they can be reused when
introducing support for the latter.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/8c05b4d283b5d765fbc6f64cee9a247cded29409.1706192990.git.geert+renesas@glider.be

Factor out the parts on the White Hawk CPU board that are also present
on the White Hawk Single board, so they can be reused when introducing
support for the latter.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/50676e7e9ac1c50ab450c030481f60ece4c3947e.1706192990.git.geert+renesas@glider.be

The White Hawk CPU and BreakOut board DTS is specific to R-Car V4H.
Document it in the top-level comment.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/de81db7ca38c8f4737092bdac6891e9db4bb9bd6.1706192990.git.geert+renesas@glider.be

The White Hawk CSI/DSI and RAVB/Ethernet(1000Base-T1) sub boards are not
specific to R-Car V4H.

Hence rename their DTS file names to drop the "r8a779g0-" prefix, and
remove any references to R-Car V4H.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/f89613d0df04cfa6196f8797fe655cf7cec812de.1706192990.git.geert+renesas@glider.be

Alphabetical by node name.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/f375293d6e21659ee30a86e2b46e4998a75ea3b5.1706192990.git.geert+renesas@glider.be

The White Hawk CPU board can be used standalone, without connecting it
to the White Hawk BreakOut board.

Add a DTS file for supporting this use case.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/95ac53e7f2bc42402eb411ad7f64a66864a3de01.1706192990.git.geert+renesas@glider.be