Device tree integer properties are encoded in big-endian format, but some of
the Freescale ASoC drivers were assuming that the host is in big-endian format
as well.  Although this is true, it's better to use endian-safe accessors.

Also add a check for a failed ioremap() call in the SSI driver.
Signed-off-by: Timur Tabi <timur@freescale.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>

Don't require an audio rate SYSCLK in hw_params() in order to better
support microphone detection use cases.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

ReTune Mobile modes are not currently supported.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>

We really should be getting the interrupt - if we don't get one it's very
likely that the configuration is incorrect and audio will fail. Also
increase the timeout substantially in this case for safety.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>

The chip can actually support SPI so we shouldn't assume we've got an I2C
device even though that's the most common configuration.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>

Currently the rbtree code will write out the entire register map when
doing a cache sync which is wasteful and will slow things down. Check
to see if the value we're about to write is the default and don't bother
restoring it if it is, either the value will have been retained or the
device will have been reset and holds the value already.

We should really store the defaults in the nodes but this resolves the
immediate issue.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Cc: stable@kernel.org

Some ASoC components depend on other ASoC components to provide clocks and
power resources in order to probe() and vice versa for remove().

Allow components to be ordered so that components can be probed() and removed()
in sequences that conform to their dependencies.
Signed-off-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Currently pcm_new() passes in 3 arguments :- card, pcm and DAI.

Refactor this to only pass in 1 argument (i.e. the rtd) since struct rtd contains
card, pcm and DAI along with other members too that are useful too.
Signed-off-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Fix the codec_name field of the dai_link to match the actual device name
of the codec. Otherwise the card won't be instantiated.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@kernel.org

Commit f97d0c6d ("ASoC: AD1836: Add input gain control for ADC2") contained
a typo in the register name, causing a build error. This patch fixes it.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

removing unnecessary if(ret) checks

This updated patch corrects a minor spelling problem in the commit message
and resolves two other (similar) issues found in wm8940.c by Jonathan Cameron.
Signed-off-by: Greg Dietsche <Gregory.Dietsche@cuw.edu>
Acked-by: Jonathan Cameron <jic23@cam.ac.uk>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@kernel.org

The AD1836 has a PGA for its second ADC. This patch adds a control for
adjusting the the gain of the PGA.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

The control_type field is never used, so it can be removed.  The
control_data field is used to initialize the codec's control_data field,
but since this is also done by the snd-soc-cache core, the redundant
assignment can be removed and the field can be dropped.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

The AD183X codec devices are mostly register compatible and can easily be
supported by the same driver.  The main difference between those devices
is the number of DACs and ADCs.

This patch adjusts the driver to allocate the controls, DAPM widgets and
routes for the DACs and ADCs dynamically based on the chip type.

The AD1836 is a bit special in that it supports different modes for its second
ADC, so it needs some special handling. Right now the driver hardcodes the mode
to the differential PGA mode.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Use snd_soc_update_bits for read-modify-write register access instead of
open-coding it using snd_soc_read and snd_soc_write.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

The different ADC and DAC controls follow the same scheme, so add some helper
macros for declaring them.
This should make the code a bit more readable and also decreases the code size
a bit.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Now that the CODEC driver supports it defer configuration of the system
clock until bias management which is a much more idiomatic place to do
system power control and makes things a lot more happy when we're using
both interfaces.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>

This allows the card driver to use the bias level variable more easily in
multi component systems.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>

The card callback will get called for each DAPM context in the card so it
can be useful for it to know which device is currently undergoing a
transition.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>

No functional changes but much less indentation.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>

It's redundant now thanks to the use of the generic trace infrastructure.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>

More with the legibility.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>

If the only widgets active within a CODEC are supplies and micbiases we
are not passing audio, we are probably just doing microphone detection.
This will not generally require either fully accurate reference voltages
or much power so

If this turns out to be unsuitable for some systems we can provide a
facility to override this decision.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>

Rather than a simple flag to say if we want the DAPM context to be at full
power specify the target bias state. This should have no current effect
but is a bit more direct and so makes it easier to change our decisions
about the which bias state to go into in future.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>

Allow more dynamic management of the device clocking by allowing BCLK to
be calculated when we set SYSCLK. This means that if the system is idle
when hw_params() runs then we don't try to use the SYSCLK used in that case
to set up the BCLK dividers, we can instead wait until a later point such
as bias level configuration. This makes it easier to manage low power modes.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>

Avoids issues if someone does a read followed by restore and doesn't mask
out only the bits being updated.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>

When the FLL locks on the WM8915 an interrupt is generated.  For safety
error out if we don't get that interrupt when the IRQ output of the
WM8915 is hooked up.  Since we *really* expect an interrupt but the
threaded IRQ handler may take a bit longer than expected to get
scheduled also dramatically increase the delay in this case.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>