- 30 Jun, 2022 5 commits
-
-
Bjorn Andersson authored
Introduce initial support for the Qualcomm SC8280XP platform, aka 8cx Gen 3. This initial contribution supports SMP, CPUfreq, CPU cluster idling, GCC, TLMM, SMMU, RPMh regulators, power-domains and clocks, interconnects, some QUPs, UFS, remoteprocs, USB, watchdog, LLCC and tsens. Signed-off-by:
Bjorn Andersson <bjorn.andersson@linaro.org> Reviewed-by:
Johan Hovold <johan+linaro@kernel.org> Reviewed-by:
Konrad Dybcio <konrad.dybcio@somainline.org> Reviewed-by:
Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> Link: https://lore.kernel.org/r/20220629041438.1352536-4-bjorn.andersson@linaro.org
-
Bjorn Andersson authored
Add a client for the NSP1 found in some recent Qualcomm platforms. Acked-by:
-
Bjorn Andersson authored
Add the CRD (Compute Reference Design?) and the Lenovo Thinkpad X13s to the valid device compatibles found on the sc8280xp platform. Signed-off-by:
-
Sibi Sankar authored
Add interconnects requirements for the SCM interface on SM8450 SoCs. Signed-off-by:
Sibi Sankar <quic_sibis@quicinc.com> Signed-off-by:
-
Dmitry Baryshkov authored
The IFC6560 is a board from Inforce Computing, built around the SDA660 SoC. This patch describes core clocks, some regulators from the two PMICs, debug uart, storage, bluetooth and audio DSP remoteproc. The regulator settings are inherited from prior work by Konrad Dybcio and AngeloGioacchino Del Regno. Reviewed-by:
Marijn Suijten <marijn.suijten@somainline.org> Signed-off-by:
Dmitry Baryshkov <dmitry.baryshkov@linaro.org> Co-developed-by:
-
- 28 Jun, 2022 12 commits
-
-
Dmitry Baryshkov authored
Add binding documentation for the Inforce IFC6560 board which uses Snapdragon SDA660. Reviewed-by:
Rob Herring <robh@kernel.org> Signed-off-by:
-
Dmitry Baryshkov authored
This results in dts duplication, but per mutual agreement card detect pin configuration belongs to the board files. Move it from the SoC dtsi to the board DT files. Suggested-by:
-
Dmitry Baryshkov authored
Fix the device tree node in the &sdc2_state_on override. The sdm630 uses 'clk' rather than 'pinconf-clk'. Fixes: 4c1d849e ("arm64: dts: qcom: sdm630-xperia: Retire sdm630-sony-xperia-ganges.dtsi") Reviewed-by:
-
Dmitry Baryshkov authored
ICC path for the GPU incorrectly states <&gnoc 1 &bimc 5>, which is a path from SLAVE_GNOC_BIMC to SLAVE_EBI. According to the downstream kernel sources, the GPU uses MASTER_OXILI here, which is equivalent to <&bimc 1 ...>. While we are at it, use defined names instead of the numbers for this interconnect path. Fixes: 5cf69dcb ("arm64: dts: qcom: sdm630: Add Adreno 508 GPU configuration") Reported-by:
-
Dmitry Baryshkov authored
Add DT entries for the second DWC3 USB host, which is limited to the USB2.0 (HighSpeed), and the corresponding QUSB PHY. Reviewed-by:
-
Dmitry Baryshkov authored
In preparation to adding second USB host/PHY pair, change first USB PHY's label to qusb2phy0. Suggested-by:
-
Dmitry Baryshkov authored
According to the downstram DT file, the qusb2phy ref clock should be GCC_RX0_USB2_CLKREF_CLK, not GCC_RX1_USB2_CLKREF_CLK. Fixes: c65a4ed2 ("arm64: dts: qcom: sdm630: Add USB configuration") Cc: Konrad Dybcio <konrad.dybcio@somainline.org> Reviewed-by:
-
Dmitry Baryshkov authored
The SoC's device tree file disables gpucc and adreno's SMMU by default. So let's disable the GPU too. Moreover it looks like SMMU might be not usable without additional patches (which means that GPU is unusable too). No board uses GPU at this moment. Fixes: 5cf69dcb ("arm64: dts: qcom: sdm630: Add Adreno 508 GPU configuration") Reviewed-by:
-
Dmitry Baryshkov authored
Follow the typical practice and keep DSI1/DSI1 PHY disabled by default. They should be enabled in the board DT files. No existing boards use them at this moment. Reviewed-by:
-
Dmitry Baryshkov authored
Follow the typical practice and keep DSI0/DSI0 PHY disabled by default. They should be enabled in the board DT files. No existing boards use them at this moment. Suggested-by:
-
Krzysztof Kozlowski authored
The PM8916 and PMS405 PMIC GPIOs are interrupt controllers, as described in the bindings and used by the driver. Drop the interrupts (apparently copied from downstream tree), just like in commit 61d2ca50 ("arm64: dts: qcom: fix pm8150 gpio interrupts"): qcs404-evb-4000.dtb: gpio@c000: 'interrupts' does not match any of the regexes: '-state$', 'pinctrl-[0-9]+' qcs404-evb-4000.dtb: gpio@c000: 'interrupt-controller' is a required property Signed-off-by:
-
Krzysztof Kozlowski authored
The new Qualcomm PMIC GPIO bindings require gpio-ranges property: sm8250-sony-xperia-edo-pdx203.dtb: gpio@c000: 'gpio-ranges' is a required property Signed-off-by:
-
- 27 Jun, 2022 23 commits
-
-
Krzysztof Kozlowski authored
The CAMSS DTSI device node, which came after the bindings were merged, got the interrupts ordered differently then specified in the bindings: sdm630-sony-xperia-nile-pioneer.dtb: camss@ca00000: interrupt-names:0: 'csid0' was expected Reordering them to match bindings should not cause ABI issues, because the driver relies on names, not ordering. Signed-off-by:
-
Krzysztof Kozlowski authored
The CAMSS DTSI device node, which came after the bindings were merged, got the regs ordered differently then specified in the bindings: sdm636-sony-xperia-ganges-mermaid.dtb: camss@ca00000: reg-names:0: 'csi_clk_mux' was expected Reordering them to match bindings should not cause ABI issues, because the driver relies on names, not ordering. Signed-off-by:
-
Krzysztof Kozlowski authored
The CAMSS DTSI device node, which came after the bindings were merged, got the clocks ordered differently then specified in the bindings: sdm636-sony-xperia-ganges-mermaid.dtb: camss@ca00000: reg-names:4: 'csid3' was expected Reordering them to match bindings should not cause ABI issues, because the driver relies on names, not ordering. Signed-off-by:
-
Krzysztof Kozlowski authored
The bindings require that every pin configuration comes with 'function' property. There is also no 'drive-strength' property but 'qcom,drive-strength': msm8994-msft-lumia-octagon-cityman.dtb: gpios@c000: amsel-high-state: 'oneOf' conditional failed, one must be fixed: 'drive-strength' does not match any of the regexes: 'pinctrl-[0-9]+' 'bias-pull-up', 'drive-strength', 'function', 'pins' do not match any of the regexes: '(pinconf|-pins)$', 'pinctrl-[0-9]+' Signed-off-by: -
Krzysztof Kozlowski authored
The bindings require that every pin configuration comes with 'function' property. Add such to PM8994 GPIO5. Signed-off-by:
-
Krzysztof Kozlowski authored
The bindings require all PMIC GPIO nodes to have two compatibles - specific followed by SPMI or SSBI fallback. Add the fallback to fix warnings like: msm8916-samsung-serranove.dtb: gpios@c000: compatible: ['qcom,pm8916-gpio'] is too short Signed-off-by:
-
Krzysztof Kozlowski authored
DT schema expects PMIC GPIO pin configuration nodes to be named with '-state' suffix. Optional children should be either 'pinconf' or followed with '-pins' suffix. This fixes dtbs_check warnings like: sdm845-xiaomi-beryllium.dtb: gpios@c000: 'vol-up-active' does not match any of the regexes: '-state$', 'pinctrl-[0-9]+' Signed-off-by:
-
Marijn Suijten authored
2700000 is not a multiple of pmic4_pldo's step size of 8000 (with base voltage 1664000), resulting in pm8998-rpmh-regulators not probing. Just as we did with MSM8998's Sony Yoshino Poplar [1], round the voltages down to err on the cautious side and leave a comment in place to document this discrepancy wrt downstream sources. [1]: https://lore.kernel.org/linux-arm-msm/20220507153627.1478268-1-marijn.suijten@somainline.org/ Fixes: 30a7f99b ("arm64: dts: qcom: Add support for SONY Xperia XZ2 / XZ2C / XZ3 (Tama platform)") Signed-off-by:
-
Konrad Dybcio authored
On MSM8996, the default bootloader configuration leaves the hosts in some weird state that never allows them to function properly under Linux. Add the hardware resets so that we can start clean and get them actually working. Signed-off-by:
-
Konrad Dybcio authored
It looks like all Tone devices out in the wild are using PMI8996, which suggests the PMI8994-variant DTs are not needed. Remove them. Signed-off-by:
-
Konrad Dybcio authored
Tone does not have a functioning bootloader framebuffer and Linux allocates the DRM framebuffer dynamically. Free up 36 MiB of precious RAM by removing this reservation. Signed-off-by:
-
Konrad Dybcio authored
Merge the two DT files into one, sort the nodes and fix up a couple of style incoherencies by adding some newlines, removing some, sorting properties etc. Signed-off-by:
-
Konrad Dybcio authored
While the Pro-1 is based on MTP and is very close to it, it's really not great for it to include the MTP dtsi straight up, as any small change will affect both boards and not all of them will apply to the phone as well. Signed-off-by:
-
Konrad Dybcio authored
Sort the includes and remove unused ones. Signed-off-by:
-
Konrad Dybcio authored
This is required to keep the display working with MMCC enabled until proper panel support is in place. Signed-off-by:
-
Konrad Dybcio authored
MMCC is a component of the SoC that should always be configured. It was kept off due to misconfiguration on clamshell machines. Keep it disabled on these ones and enable it by default on all the others. Exactly the same story applies to MMSS_SMMU, which directly depends on MMCC. Do note, that if a platform doesn't use neither EFIFB (only applies to WoA devices in this case) or simplefb (applies to precisely 2 msm8998 devices as of this commit), this will not cause any harm. Signed-off-by:
-
Konrad Dybcio authored
This is the standard way. Signed-off-by:
-
Konrad Dybcio authored
Add some newlines, reorder some properties, remove some indentation to make it more coherent. Signed-off-by:
-
Konrad Dybcio authored
Now that a label is added, use it! Signed-off-by:
-
Konrad Dybcio authored
It's not necessary and the SoC clocks{} node doesn't use it either. Signed-off-by: -
Konrad Dybcio authored
While not strictly necessary, at least on maple, configure the USB extcon, which requires two pins on Yoshino. Signed-off-by:
-
Konrad Dybcio authored
It's disabled on downstream, follow it. Signed-off-by:
-
Konrad Dybcio authored
Reorder properties to match new laptop DTs, change hex to dec. Signed-off-by:
-
