- 04 Apr, 2024 2 commits
-
-
Kuan-Chung Chen authored
8922A needs to set UL MU/OFDMA power and fine tune power error tolerance for proper response to AP's trigger frame. Signed-off-by:
Kuan-Chung Chen <damon.chen@realtek.com> Signed-off-by:
Ping-Ke Shih <pkshih@realtek.com> Link: https://msgid.link/20240401063818.12880-1-pkshih@realtek.com
-
Po-Hao Huang authored
When wpa_supplicant is initiated by users and not by NetworkManager, the CQM configuration might not be set. Without this setting, ICs with connection quality monitor handled by firmware won't detect connection loss. To fix this we prepare a default setting upon associated at first, then update again if any is given later. Signed-off-by:
Po-Hao Huang <phhuang@realtek.com> Signed-off-by:
-
- 03 Apr, 2024 8 commits
-
-
Ping-Ke Shih authored
Mesh point was added during development, but not remove at first submission, so it should not work properly. Remove it to reflect correct supported features. Signed-off-by:
-
Ping-Ke Shih authored
For adaption EQ circuit, this HW design and affected by EIEOS (Electrical Idle Exit Order Set) amplitude from platform and process from IC, so disable EQ to improve that. Signed-off-by:
-
Ping-Ke Shih authored
Increase PCI BER (bit error rate) count depth setting which could increase PHY circuit fault tolerance and improve compatibility. Signed-off-by:
-
Zong-Zhe Yang authored
Configure applicable values for IC (Industry Canada) on 5.9GHz. Signed-off-by:
Zong-Zhe Yang <kevin_yang@realtek.com> Signed-off-by:
-
Chia-Yuan Li authored
After firmware boots, it reads keys info from efuse and checks secure checksum, but suddenly failed to access efuse resulting in probe failure, and driver throws messages: rtw89_8852be 0000:03:00.0: fw security fail rtw89_8852be 0000:03:00.0: download firmware fail rtw89_8852be 0000:03:00.0: [ERR]fwdl 0x1E0 = 0xe2 rtw89_8852be 0000:03:00.0: [ERR]fwdl 0x83F0 = 0x210090 Retry five times to resolve rare abnormal hardware state. Signed-off-by:
Chia-Yuan Li <leo.li@realtek.com> Signed-off-by:
-
Po-Hao Huang authored
Declare beacon filter and connection monitor for 8922A. This offloads connection monitor mechanism to firmware, which is required for future multi-link scenarios. Currently firmware only supports non-MLO connections. Signed-off-by:
-
Po-Hao Huang authored
8922a FW supports RNR parsing, provide template probe requests and let FW do the replacement for SSID/BSSID/short SSIDs. Don't declare WIPHY_FLAG_SPLIT_SCAN_6GHZ so proper IEs such as 6 GHz capabilities can be passed down within the same scan request. Signed-off-by:
-
Chih-Kang Chang authored
Update scan offload H2C length to fit new FW format. This change is required after FW version 0.35.15.0. Since the first release of firmware is 0.35.18.0, we don't maintain backward compatibility. Signed-off-by:
Chih-Kang Chang <gary.chang@realtek.com> Signed-off-by:
-
- 29 Mar, 2024 1 commit
-
-
Ping-Ke Shih authored
Since only station mode has been tested on SDIO chips, only keep it support for SDIO chips to reflect correct supported features. Link: https://lore.kernel.org/linux-wireless/87wmpu1do6.fsf@kernel.org/T/#t Link: https://lore.kernel.org/linux-wireless/36972ff5-0c48-4bd2-8f9a-9649bfa24225@lexina.in/ Cc: Martin Blumenstingl <martin.blumenstingl@googlemail.com> Reviewed-by:
Martin Blumenstingl <martin.blumenstingl@googlemail.com> Signed-off-by:
-
- 26 Mar, 2024 2 commits
-
-
Chia-Yuan Li authored
The hardware command parser of txptctrl (TX protocol control) has overly stringent timeout conditions, which results in false alarm. So disable it. Signed-off-by:
-
Ching-Te Ku authored
Fix Wi-Fi 2.4Ghz throughput drop over than 40% when Bluetooh is idle. The code flow will read registers during Wi-Fi power saving, and be returned, which results in incorrect counters to do mechanism judgment. Adjust the code flow. Will leave Wi-Fi power save mode first then update counters. Signed-off-by:
Ching-Te Ku <ku920601@realtek.com> Signed-off-by:
-
- 22 Mar, 2024 2 commits
-
-
Dmitry Antipov authored
In 'rtl92cu_set_hw_reg()', always assume that QoS mode is enabled as it was hardcoded since an initial commit. Compile tested only. Found by Linux Verification Center (linuxtesting.org) with SVACE. Signed-off-by:
Dmitry Antipov <dmantipov@yandex.ru> Signed-off-by:
-
Dmitry Antipov authored
Since WMM support was never actually implemented and related TODO is more than 13 years old, it might be reasonable to remove all of the WMM stubs from rtl8192cu and simplify related code. Minor comment style adjustments suggested by checkpatch.pl, compile tested only. Found by Linux Verification Center (linuxtesting.org) with SVACE. Signed-off-by:
-
- 20 Mar, 2024 1 commit
-
-
Martin Kaistra authored
In order to connect to networks which require 802.11w, add the MFP_CAPABLE flag and let mac80211 do the actual crypto in software. When a robust management frames is received, rx_dec->swdec is not set, even though the HW did not decrypt it. Extend the check and don't set RX_FLAG_DECRYPTED for these frames in order to use SW decryption. Signed-off-by:
Martin Kaistra <martin.kaistra@linutronix.de> Reviewed-by:
-
- 18 Mar, 2024 1 commit
-
-
Víctor Gonzalo authored
The module metadata for the firmware file mrvl/sd8801_uapsta.bin is missing. Signed-off-by:
Víctor Gonzalo <victor.gonzalo@anddroptable.net> Acked-by:
Brian Norris <briannorris@chromium.org> Signed-off-by:
Kalle Valo <kvalo@kernel.org> Link: https://msgid.link/20240313183156.2234301-1-victor.gonzalo@anddroptable.net
-
- 14 Mar, 2024 16 commits
-
-
Fiona Klute authored
This driver uses the new rtw8703b chip driver code. Acked-by:
Pavel Machek <pavel@ucw.cz> Signed-off-by:
Fiona Klute <fiona.klute@gmx.de> Signed-off-by:
-
Fiona Klute authored
Sometimes 8703b firmware is still active from previous use when the driver needs to download the firmware during MAC activation. Reset it in that case. Acked-by:
-
Fiona Klute authored
Initialization tables for rtw8703b: Initial register values and TX power limits. Acked-by:
-
Fiona Klute authored
Initialization table definitions for rtw8703b. Acked-by:
-
Fiona Klute authored
This is the main source for the new rtw88_8703b chip driver. Acked-by:
-
Fiona Klute authored
This is the main header for the new rtw88_8703b chip driver. Acked-by:
-
Fiona Klute authored
default_cck_index is used in power track, the rx_cck_agc_report_type for RX PHY status. GET_RX_DESC_BW is an RX descriptor field not used by the other chip drivers. Acked-by:
-
Fiona Klute authored
Some 8703b chips contain invalid EFUSE data, getting detailed information is critical when analyzing issues caused by that. Acked-by:
-
Fiona Klute authored
The already supported 8723d chip is very similar to 8703b/8723cs, split code that can be shared into a new module. The spec definition tables are combined into a struct so we only need one EXPORT_SYMBOL for them all. Acked-by:
-
Ping-Ke Shih authored
Add 8922AE to Makefile and Kconfig. Currently, it can support STA, AP and monitor modes with good performance. Implemented initial BT-coexistence function only, and will to fine tune this component. Signed-off-by:
-
Ching-Te Ku authored
Implement the chip operation function for 8922a, it related to TX power, RX gain, antenna position, packet priority and so on. Also assign coexistence priority table for hardware PTA using. Add settings to avoid uncertainties propagation when Wi-Fi Rx due to RF gain mismatch. Signed-off-by:
-
Ching-Te Ku authored
In order to packet up the slots information, the TLV header has updated. TDMA slot parameters also use the TLV header to packet up to H2C, so upgrade to version 7. Signed-off-by:
-
Ching-Te Ku authored
In order to packet up the slots information, the TLV header has updated. TDMA also use the TLV header to packet up to H2C, so upgrade to version 7. Signed-off-by:
-
Ching-Te Ku authored
Because there is new hardware structure and Wi-Fi 7 protocol, the antenna settings need to concern more complex for Wi-Fi 7 using. The antenna setting included grant control signal, they decide which MAC/Port or Bluetooth can do traffic. Signed-off-by:
-
Ching-Te Ku authored
In order to control the hardware band and related protocol control, add version 8 format and related logic to control the mechanism. Signed-off-by:
-
Randy Dunlap authored
Having an empty default: case in a switch statement causes a warning (when using Clang; I don't see the warning when using gcc), so add a "break;" to the default case to prevent the warning: drivers/ssb/main.c:1149:2: warning: label at end of compound statement is a C2x extension [-Wc2x-extensions] Fixes: e27b02e2 ("ssb: drop use of non-existing CONFIG_SSB_DEBUG symbol") Signed-off-by:
Randy Dunlap <rdunlap@infradead.org> Reported-by:
kernel test robot <lkp@intel.com> Closes: https://lore.kernel.org/oe-kbuild-all/202403130717.TWm17FiD-lkp@intel.com/ Cc: Michael Büsch <m@bues.ch> Cc: linux-wireless@vger.kernel.org Cc: Kalle Valo <kvalo@kernel.org> Cc: Johannes Berg <johannes@sipsolutions.net> Cc: llvm@lists.linux.dev Acked-by:
Michael Büsch <m@bues.ch> Reviewed-by:
Nathan Chancellor <nathan@kernel.org> Signed-off-by:
-
- 12 Mar, 2024 6 commits
-
-
Randy Dunlap authored
CONFIG_SSB_DEBUG is used in one header file and nowhere else, so remove it and the now-empty inline function that contained it. Also remove the call to the empty inline function. The empty "default:" case is kept to prevent 2 compiler warnings: drivers/ssb/main.c:1133:9: warning: enumeration value 'SSB_BUSTYPE_PCMCIA' not handled in switch [-Wswitch] drivers/ssb/main.c:1133:9: warning: enumeration value 'SSB_BUSTYPE_SDIO' not handled in switch [-Wswitch] Reported-by:
Ying Sun <sunying@isrc.iscas.ac.cn> Link: https://lore.kernel.org/lkml/4e8525fe.607e2.18a8ddfdce8.Coremail.sunying@isrc.iscas.ac.cn/Signed-off-by:
-
Marek Vasut authored
CYW43439 is a Wi-Fi + Bluetooth combo device from Infineon. The WiFi part is capable of 802.11 b/g/n. This chip is present e.g. on muRata 1YN module. Extend the binding with its DT compatible. Signed-off-by:
Marek Vasut <marex@denx.de> Acked-by:
Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> Signed-off-by:
-
Uwe Kleine-König authored
The .remove() callback for a platform driver returns an int which makes many driver authors wrongly assume it's possible to do error handling by returning an error code. However the value returned is ignored (apart from emitting a warning) and this typically results in resource leaks. To improve here there is a quest to make the remove callback return void. In the first step of this quest all drivers are converted to .remove_new(), which already returns void. Eventually after all drivers are converted, .remove_new() will be renamed to .remove(). Trivially convert this driver from always returning zero in the remove callback to the void returning variant. Signed-off-by:
Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Signed-off-by:
-
Duoming Zhou authored
The kzalloc() in brcmf_pcie_download_fw_nvram() will return null if the physical memory has run out. As a result, if we use get_random_bytes() to generate random bytes in the randbuf, the null pointer dereference bug will happen. In order to prevent allocation failure, this patch adds a separate function using buffer on kernel stack to generate random bytes in the randbuf, which could prevent the kernel stack from overflow. Fixes: 91918ce8 ("wifi: brcmfmac: pcie: Provide a buffer of random bytes to the device") Suggested-by:
Arnd Bergmann <arnd@arndb.de> Signed-off-by:
Duoming Zhou <duoming@zju.edu.cn> Signed-off-by:
-
Rand Deeb authored
The ssb_device_uevent() function first attempts to convert the 'dev' pointer to 'struct ssb_device *'. However, it mistakenly dereferences 'dev' before performing the NULL check, potentially leading to a NULL pointer dereference if 'dev' is NULL. To fix this issue, move the NULL check before dereferencing the 'dev' pointer, ensuring that the pointer is valid before attempting to use it. Found by Linux Verification Center (linuxtesting.org) with SVACE. Signed-off-by:
Rand Deeb <rand.sec96@gmail.com> Signed-off-by:
-
Dian-Syuan Yang authored
We used EHT capability of 20MHz-only as rate mask to RA (rate adaptive) H2C command when connecting with AP set EHT 20MHz. It would get the wrong rate mask and the MCS rate can only reach MCS11. According to the description of 802.11be spec, if all supported channel bandwidth field of HE PHY capabilities are zero, then the EHT capability of 20MHz-only is valid. As a result, we adjust the code to set correct rate mask based on HE PHY bandwidth capability. Signed-off-by:
Dian-Syuan Yang <dian_syuan0116@realtek.com> Signed-off-by:
-
- 11 Mar, 2024 1 commit
-
-
David S. Miller authored
Herve Codina says: ==================== Add support for QMC HDLC This series introduces the QMC HDLC support. Patches were previously sent as part of a full feature series and were previously reviewed in that context: "Add support for QMC HDLC, framer infrastructure and PEF2256 framer" [1] In order to ease the merge, the full feature series has been split and needed parts were merged in v6.8-rc1: - "Prepare the PowerQUICC QMC and TSA for the HDLC QMC driver" [2] - "Add support for framer infrastructure and PEF2256 framer" [3] This series contains patches related to the QMC HDLC part (QMC HDLC driver): - Introduce the QMC HDLC driver (patches 1 and 2) - Add timeslots change support in QMC HDLC (patch 3) - Add framer support as a framer consumer in QMC HDLC (patch 4) Compare to the original full feature series, a modification was done on patch 3 in order to use a coherent prefix in the commit title. I kept the patches unsquashed as they were previously sent and reviewed. Of course, I can squash them if needed. Compared to the previous iteration: https://lore.kernel.org/linux-kernel/20240306080726.167338-1-herve.codina@bootlin.com/ this v7 series mainly: - Rename a variable. - Fix reverse xmas tree declarations. - Add 'Acked-by' tag. ==================== Signed-off-by:
David S. Miller <davem@davemloft.net>
-
