- 18 May, 2022 7 commits
-
-
Aya Levin authored
When the driver is in switchdev mode and rx-gro-hw is set, the RQ needs special CQE handling. Till then, block setting of rx-gro-hw feature in switchdev mode, to avoid failure while setting the feature due to failure while opening the RQ. Fixes: f97d5c2a ("net/mlx5e: Add handle SHAMPO cqe support") Signed-off-by:
Aya Levin <ayal@nvidia.com> Reviewed-by:
Tariq Toukan <tariqt@nvidia.com> Signed-off-by:
Saeed Mahameed <saeedm@nvidia.com>
-
Maxim Mikityanskiy authored
The body of mlx5e_napi_poll is wrapped into rcu_read_lock to be able to read the XDP program pointer using rcu_dereference. However, the trap RQ NAPI doesn't use rcu_read_lock, because the trap RQ works only in the non-linear mode, and mlx5e_skb_from_cqe_nonlinear, until recently, didn't support XDP and didn't call rcu_dereference. Starting from the cited commit, mlx5e_skb_from_cqe_nonlinear supports XDP and calls rcu_dereference, but mlx5e_trap_napi_poll doesn't wrap it into rcu_read_lock. It leads to RCU-lockdep warnings like this: WARNING: suspicious RCU usage This commit fixes the issue by adding an rcu_read_lock to mlx5e_trap_napi_poll, similarly to mlx5e_napi_poll. Fixes: ea5d49bd ("net/mlx5e: Add XDP multi buffer support to the non-linear legacy RQ") Signed-off-by:Maxim Mikityanskiy <maximmi@nvidia.com> Reviewed-by:
-
Yevgeny Kliteynik authored
When modifying TTL, packet's csum has to be recalculated. Due to HW issue in ConnectX-5, csum recalculation for modify TTL on RX is supported through a work-around that is specifically enabled by configuration. If the work-around isn't enabled, rather than adding an unsupported action the modify TTL action on RX should be ignored. Ignoring modify TTL action might result in zero actions, so in such cases we will not convert the match STE to modify STE, as it is done by FW in DMFS. This patch fixes an issue where modify TTL action was ignored both on RX and TX instead of only on RX. Fixes: 4ff725e1 ("net/mlx5: DR, Ignore modify TTL if device doesn't support it") Signed-off-by:
Yevgeny Kliteynik <kliteyn@nvidia.com> Reviewed-by:
Alex Vesker <valex@nvidia.com> Signed-off-by:
-
Shay Drory authored
Currently, software objects of flow steering are created and destroyed during reload flow. In case a device is unloaded, the following error is printed during grace period: mlx5_core 0000:00:0b.0: mlx5_fw_fatal_reporter_err_work:690:(pid 95): Driver is in error state. Unloading As a solution to fix use-after-free bugs, where we try to access these objects, when reading the value of flow_steering_mode devlink param[1], let's split flow steering creation and destruction into two routines: * init and cleanup: memory, cache, and pools allocation/free. * create and destroy: namespaces initialization and cleanup. While at it, re-order the cleanup function to mirror the init function. [1] Kasan trace: [ 385.119849 ] BUG: KASAN: use-after-free in mlx5_devlink_fs_mode_get+0x3b/0xa0 [ 385.119849 ] Read of size 4 at addr ffff888104b79308 by task bash/291 [ 385.119849 ] [ 385.119849 ] CPU: 1 PID: 291 Comm: bash Not tainted 5.17.0-rc1+ #2 [ 385.119849 ] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.13.0-2.fc32 04/01/2014 [ 385.119849 ] Call Trace: [ 385.119849 ] <TASK> [ 385.119849 ] dump_stack_lvl+0x6e/0x91 [ 385.119849 ] print_address_description.constprop.0+0x1f/0x160 [ 385.119849 ] ? mlx5_devlink_fs_mode_get+0x3b/0xa0 [ 385.119849 ] ? mlx5_devlink_fs_mode_get+0x3b/0xa0 [ 385.119849 ] kasan_report.cold+0x83/0xdf [ 385.119849 ] ? devlink_param_notify+0x20/0x190 [ 385.119849 ] ? mlx5_devlink_fs_mode_get+0x3b/0xa0 [ 385.119849 ] mlx5_devlink_fs_mode_get+0x3b/0xa0 [ 385.119849 ] devlink_nl_param_fill+0x18a/0xa50 [ 385.119849 ] ? _raw_spin_lock_irqsave+0x8d/0xe0 [ 385.119849 ] ? devlink_flash_update_timeout_notify+0xf0/0xf0 [ 385.119849 ] ? __wake_up_common+0x4b/0x1e0 [ 385.119849 ] ? preempt_count_sub+0x14/0xc0 [ 385.119849 ] ? _raw_spin_unlock_irqrestore+0x28/0x40 [ 385.119849 ] ? __wake_up_common_lock+0xe3/0x140 [ 385.119849 ] ? __wake_up_common+0x1e0/0x1e0 [ 385.119849 ] ? __sanitizer_cov_trace_const_cmp8+0x27/0x80 [ 385.119849 ] ? __rcu_read_unlock+0x48/0x70 [ 385.119849 ] ? kasan_unpoison+0x23/0x50 [ 385.119849 ] ? __kasan_slab_alloc+0x2c/0x80 [ 385.119849 ] ? memset+0x20/0x40 [ 385.119849 ] ? __sanitizer_cov_trace_const_cmp4+0x25/0x80 [ 385.119849 ] devlink_param_notify+0xce/0x190 [ 385.119849 ] devlink_unregister+0x92/0x2b0 [ 385.119849 ] remove_one+0x41/0x140 [ 385.119849 ] pci_device_remove+0x68/0x140 [ 385.119849 ] ? pcibios_free_irq+0x10/0x10 [ 385.119849 ] __device_release_driver+0x294/0x3f0 [ 385.119849 ] device_driver_detach+0x82/0x130 [ 385.119849 ] unbind_store+0x193/0x1b0 [ 385.119849 ] ? subsys_interface_unregister+0x270/0x270 [ 385.119849 ] drv_attr_store+0x4e/0x70 [ 385.119849 ] ? drv_attr_show+0x60/0x60 [ 385.119849 ] sysfs_kf_write+0xa7/0xc0 [ 385.119849 ] kernfs_fop_write_iter+0x23a/0x2f0 [ 385.119849 ] ? sysfs_kf_bin_read+0x160/0x160 [ 385.119849 ] new_sync_write+0x311/0x430 [ 385.119849 ] ? new_sync_read+0x480/0x480 [ 385.119849 ] ? _raw_spin_lock+0x87/0xe0 [ 385.119849 ] ? __sanitizer_cov_trace_cmp4+0x25/0x80 [ 385.119849 ] ? security_file_permission+0x94/0xa0 [ 385.119849 ] vfs_write+0x4c7/0x590 [ 385.119849 ] ksys_write+0xf6/0x1e0 [ 385.119849 ] ? __x64_sys_read+0x50/0x50 [ 385.119849 ] ? fpregs_assert_state_consistent+0x99/0xa0 [ 385.119849 ] do_syscall_64+0x3d/0x90 [ 385.119849 ] entry_SYSCALL_64_after_hwframe+0x44/0xae [ 385.119849 ] RIP: 0033:0x7fc36ef38504 [ 385.119849 ] Code: 00 f7 d8 64 89 02 48 c7 c0 ff ff ff ff eb b3 0f 1f 80 00 00 00 00 48 8d 05 f9 61 0d 00 8b 00 85 c0 75 13 b8 01 00 00 00 0f 05 <48> 3d 00 f0 ff ff 77 54 c3 0f 1f 00 41 54 49 89 d4 55 48 89 f5 53 [ 385.119849 ] RSP: 002b:00007ffde0ff3d08 EFLAGS: 00000246 ORIG_RAX: 0000000000000001 [ 385.119849 ] RAX: ffffffffffffffda RBX: 000000000000000c RCX: 00007fc36ef38504 [ 385.119849 ] RDX: 000000000000000c RSI: 00007fc370521040 RDI: 0000000000000001 [ 385.119849 ] RBP: 00007fc370521040 R08: 00007fc36f00b8c0 R09: 00007fc36ee4b740 [ 385.119849 ] R10: 0000000000000000 R11: 0000000000000246 R12: 00007fc36f00a760 [ 385.119849 ] R13: 000000000000000c R14: 00007fc36f005760 R15: 000000000000000c [ 385.119849 ] </TASK> [ 385.119849 ] [ 385.119849 ] Allocated by task 65: [ 385.119849 ] kasan_save_stack+0x1e/0x40 [ 385.119849 ] __kasan_kmalloc+0x81/0xa0 [ 385.119849 ] mlx5_init_fs+0x11b/0x1160 [ 385.119849 ] mlx5_load+0x13c/0x220 [ 385.119849 ] mlx5_load_one+0xda/0x160 [ 385.119849 ] mlx5_recover_device+0xb8/0x100 [ 385.119849 ] mlx5_health_try_recover+0x2f9/0x3a1 [ 385.119849 ] devlink_health_reporter_recover+0x75/0x100 [ 385.119849 ] devlink_health_report+0x26c/0x4b0 [ 385.275909 ] mlx5_fw_fatal_reporter_err_work+0x11e/0x1b0 [ 385.275909 ] process_one_work+0x520/0x970 [ 385.275909 ] worker_thread+0x378/0x950 [ 385.275909 ] kthread+0x1bb/0x200 [ 385.275909 ] ret_from_fork+0x1f/0x30 [ 385.275909 ] [ 385.275909 ] Freed by task 65: [ 385.275909 ] kasan_save_stack+0x1e/0x40 [ 385.275909 ] kasan_set_track+0x21/0x30 [ 385.275909 ] kasan_set_free_info+0x20/0x30 [ 385.275909 ] __kasan_slab_free+0xfc/0x140 [ 385.275909 ] kfree+0xa5/0x3b0 [ 385.275909 ] mlx5_unload+0x2e/0xb0 [ 385.275909 ] mlx5_unload_one+0x86/0xb0 [ 385.275909 ] mlx5_fw_fatal_reporter_err_work.cold+0xca/0xcf [ 385.275909 ] process_one_work+0x520/0x970 [ 385.275909 ] worker_thread+0x378/0x950 [ 385.275909 ] kthread+0x1bb/0x200 [ 385.275909 ] ret_from_fork+0x1f/0x30 [ 385.275909 ] [ 385.275909 ] The buggy address belongs to the object at ffff888104b79300 [ 385.275909 ] which belongs to the cache kmalloc-128 of size 128 [ 385.275909 ] The buggy address is located 8 bytes inside of [ 385.275909 ] 128-byte region [ffff888104b79300, ffff888104b79380) [ 385.275909 ] The buggy address belongs to the page: [ 385.275909 ] page:00000000de44dd39 refcount:1 mapcount:0 mapping:0000000000000000 index:0x0 pfn:0x104b78 [ 385.275909 ] head:00000000de44dd39 order:1 compound_mapcount:0 [ 385.275909 ] flags: 0x8000000000010200(slab|head|zone=2) [ 385.275909 ] raw: 8000000000010200 0000000000000000 dead000000000122 ffff8881000428c0 [ 385.275909 ] raw: 0000000000000000 0000000080200020 00000001ffffffff 0000000000000000 [ 385.275909 ] page dumped because: kasan: bad access detected [ 385.275909 ] [ 385.275909 ] Memory state around the buggy address: [ 385.275909 ] ffff888104b79200: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 fc fc [ 385.275909 ] ffff888104b79280: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc [ 385.275909 ] >ffff888104b79300: fa fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb [ 385.275909 ] ^ [ 385.275909 ] ffff888104b79380: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc [ 385.275909 ] ffff888104b79400: fa fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb [ 385.275909 ]] Fixes: e890acd5 ("net/mlx5: Add devlink flow_steering_mode parameter") Signed-off-by:Shay Drory <shayd@nvidia.com> Reviewed-by:
Mark Bloch <mbloch@nvidia.com> Signed-off-by:
-
Maor Dickman authored
In order to support multiple destination FTEs with SW steering FW table is created with single FTE with multiple actions and SW steering rule forward to it. When creating this table, flow source isn't set according to the original FTE. Fix this by passing the original FTE flow source to the created FW table. Fixes: 34583bee ("net/mlx5: DR, Create multi-destination table for SW-steering use") Signed-off-by:
Maor Dickman <maord@nvidia.com> Reviewed-by:
-
Duoming Zhou authored
There are sleep in atomic context bugs when the request to secure element of st-nci is timeout. The root cause is that nci_skb_alloc with GFP_KERNEL parameter is called in st_nci_se_wt_timeout which is a timer handler. The call paths that could trigger bugs are shown below: (interrupt context 1) st_nci_se_wt_timeout nci_hci_send_event nci_hci_send_data nci_skb_alloc(..., GFP_KERNEL) //may sleep (interrupt context 2) st_nci_se_wt_timeout nci_hci_send_event nci_hci_send_data nci_send_data nci_queue_tx_data_frags nci_skb_alloc(..., GFP_KERNEL) //may sleep This patch changes allocation mode of nci_skb_alloc from GFP_KERNEL to GFP_ATOMIC in order to prevent atomic context sleeping. The GFP_ATOMIC flag makes memory allocation operation could be used in atomic context. Fixes: ed06aeef ("nfc: st-nci: Rename st21nfcb to st-nci") Signed-off-by:Duoming Zhou <duoming@zju.edu.cn> Reviewed-by:
Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> Link: https://lore.kernel.org/r/20220517012530.75714-1-duoming@zju.edu.cnSigned-off-by:
Jakub Kicinski <kuba@kernel.org>
-
Christophe JAILLET authored
test_bit() tests if one bit is set or not. Here the logic seems to check of bit QL_RESET_PER_SCSI (i.e. 4) OR bit QL_RESET_START (i.e. 3) is set. In fact, it checks if bit 7 (4 | 3 = 7) is set, that is to say QL_ADAPTER_UP. This looks harmless, because this bit is likely be set, and when the ql_reset_work() delayed work is scheduled in ql3xxx_isr() (the only place that schedule this work), QL_RESET_START or QL_RESET_PER_SCSI is set. This has been spotted by smatch. Fixes: 5a4faa87 ("[PATCH] qla3xxx NIC driver") Signed-off-by:
Christophe JAILLET <christophe.jaillet@wanadoo.fr> Link: https://lore.kernel.org/r/80e73e33f390001d9c0140ffa9baddf6466a41a2.1652637337.git.christophe.jaillet@wanadoo.frSigned-off-by:
-
- 17 May, 2022 5 commits
-
-
Zixuan Fu authored
In vmxnet3_rq_create(), when dma_alloc_coherent() fails, vmxnet3_rq_destroy() is called. It sets rq->rx_ring[i].base to NULL. Then vmxnet3_rq_create() returns an error to its callers mxnet3_rq_create_all() -> vmxnet3_change_mtu(). Then vmxnet3_change_mtu() calls vmxnet3_force_close() -> dev_close() in error handling code. And the driver calls vmxnet3_close() -> vmxnet3_quiesce_dev() -> vmxnet3_rq_cleanup_all() -> vmxnet3_rq_cleanup(). In vmxnet3_rq_cleanup(), rq->rx_ring[ring_idx].base is accessed, but this variable is NULL, causing a NULL pointer dereference. To fix this possible bug, an if statement is added to check whether rq->rx_ring[0].base is NULL in vmxnet3_rq_cleanup() and exit early if so. The error log in our fault-injection testing is shown as follows: [ 65.220135] BUG: kernel NULL pointer dereference, address: 0000000000000008 ... [ 65.222633] RIP: 0010:vmxnet3_rq_cleanup_all+0x396/0x4e0 [vmxnet3] ... [ 65.227977] Call Trace: ... [ 65.228262] vmxnet3_quiesce_dev+0x80f/0x8a0 [vmxnet3] [ 65.228580] vmxnet3_close+0x2c4/0x3f0 [vmxnet3] [ 65.228866] __dev_close_many+0x288/0x350 [ 65.229607] dev_close_many+0xa4/0x480 [ 65.231124] dev_close+0x138/0x230 [ 65.231933] vmxnet3_force_close+0x1f0/0x240 [vmxnet3] [ 65.232248] vmxnet3_change_mtu+0x75d/0x920 [vmxnet3] ... Fixes: d1a890fa ("net: VMware virtual Ethernet NIC driver: vmxnet3") Reported-by:
TOTE Robot <oslab@tsinghua.edu.cn> Signed-off-by:
Zixuan Fu <r33s3n6@gmail.com> Link: https://lore.kernel.org/r/20220514050711.2636709-1-r33s3n6@gmail.comSigned-off-by:
Paolo Abeni <pabeni@redhat.com>
-
Zixuan Fu authored
In vmxnet3_rq_alloc_rx_buf(), when dma_map_single() fails, rbi->skb is freed immediately. Similarly, in another branch, when dma_map_page() fails, rbi->page is also freed. In the two cases, vmxnet3_rq_alloc_rx_buf() returns an error to its callers vmxnet3_rq_init() -> vmxnet3_rq_init_all() -> vmxnet3_activate_dev(). Then vmxnet3_activate_dev() calls vmxnet3_rq_cleanup_all() in error handling code, and rbi->skb or rbi->page are freed again in vmxnet3_rq_cleanup_all(), causing use-after-free bugs. To fix these possible bugs, rbi->skb and rbi->page should be cleared after they are freed. The error log in our fault-injection testing is shown as follows: [ 14.319016] BUG: KASAN: use-after-free in consume_skb+0x2f/0x150 ... [ 14.321586] Call Trace: ... [ 14.325357] consume_skb+0x2f/0x150 [ 14.325671] vmxnet3_rq_cleanup_all+0x33a/0x4e0 [vmxnet3] [ 14.326150] vmxnet3_activate_dev+0xb9d/0x2ca0 [vmxnet3] [ 14.326616] vmxnet3_open+0x387/0x470 [vmxnet3] ... [ 14.361675] Allocated by task 351: ... [ 14.362688] __netdev_alloc_skb+0x1b3/0x6f0 [ 14.362960] vmxnet3_rq_alloc_rx_buf+0x1b0/0x8d0 [vmxnet3] [ 14.363317] vmxnet3_activate_dev+0x3e3/0x2ca0 [vmxnet3] [ 14.363661] vmxnet3_open+0x387/0x470 [vmxnet3] ... [ 14.367309] [ 14.367412] Freed by task 351: ... [ 14.368932] __dev_kfree_skb_any+0xd2/0xe0 [ 14.369193] vmxnet3_rq_alloc_rx_buf+0x71e/0x8d0 [vmxnet3] [ 14.369544] vmxnet3_activate_dev+0x3e3/0x2ca0 [vmxnet3] [ 14.369883] vmxnet3_open+0x387/0x470 [vmxnet3] [ 14.370174] __dev_open+0x28a/0x420 [ 14.370399] __dev_change_flags+0x192/0x590 [ 14.370667] dev_change_flags+0x7a/0x180 [ 14.370919] do_setlink+0xb28/0x3570 [ 14.371150] rtnl_newlink+0x1160/0x1740 [ 14.371399] rtnetlink_rcv_msg+0x5bf/0xa50 [ 14.371661] netlink_rcv_skb+0x1cd/0x3e0 [ 14.371913] netlink_unicast+0x5dc/0x840 [ 14.372169] netlink_sendmsg+0x856/0xc40 [ 14.372420] ____sys_sendmsg+0x8a7/0x8d0 [ 14.372673] __sys_sendmsg+0x1c2/0x270 [ 14.372914] do_syscall_64+0x41/0x90 [ 14.373145] entry_SYSCALL_64_after_hwframe+0x44/0xae ... Fixes: 5738a09d ("vmxnet3: fix checks for dma mapping errors") Reported-by:
-
Xin Long authored
The global blackhole_netdev has replaced pernet loopback_dev to become the one given to the object that holds an netdev when ifdown in many places of ipv4 and ipv6 since commit 8d7017fd ("blackhole_netdev: use blackhole_netdev to invalidate dst entries"). Especially after commit faab39f6 ("net: allow out-of-order netdev unregistration"), it's no longer safe to use loopback_dev that may be freed before other netdev. This patch is to set dst dev to blackhole_netdev instead of loopback_dev in ifdown. v1->v2: - add Fixes tag as Eric suggested. Fixes: faab39f6 ("net: allow out-of-order netdev unregistration") Signed-off-by:
Xin Long <lucien.xin@gmail.com> Reviewed-by:
Eric Dumazet <edumazet@google.com> Link: https://lore.kernel.org/r/e8c87482998ca6fcdab214f5a9d582899ec0c648.1652665047.git.lucien.xin@gmail.comSigned-off-by:
-
Christophe JAILLET authored
if devm_clk_get_optional() fails, we still need to go through the error handling path. Add the missing goto. Fixes: 6328a126 ("net: systemport: Manage Wake-on-LAN clock") Signed-off-by:
Florian Fainelli <f.fainelli@gmail.com> Link: https://lore.kernel.org/r/99d70634a81c229885ae9e4ee69b2035749f7edc.1652634040.git.christophe.jaillet@wanadoo.frSigned-off-by:
-
Horatiu Vultur authored
The following two scenarios were failing for lan966x. 1. If the port had the address X and then trying to assign the same address, then the HW was just removing this address because first it tries to learn new address and then delete the old one. As they are the same the HW remove it. 2. If the port eth0 was assigned the same address as one of the other ports eth1 then when assigning back the address to eth0 then the HW was deleting the address of eth1. The case 1. is fixed by checking if the port has already the same address while case 2. is fixed by checking if the address is used by any other port. Fixes: e18aba89 ("net: lan966x: add mactable support") Signed-off-by:
Horatiu Vultur <horatiu.vultur@microchip.com> Link: https://lore.kernel.org/r/20220513180030.3076793-1-horatiu.vultur@microchip.comSigned-off-by:
-
- 16 May, 2022 3 commits
-
-
Jonathan Lemon authored
delta_ns is a s64, but it was being passed ptp_ocp_adjtime_coarse as an u64. Also, it turns out that timespec64_add_ns() only handles positive values, so perform the math with set_normalized_timespec(). Fixes: 90f8f4c0 ("ptp: ocp: Add ptp_ocp_adjtime_coarse for large adjustments") Suggested-by:
Vadim Fedorenko <vfedorenko@novek.ru> Signed-off-by:
Jonathan Lemon <jonathan.lemon@gmail.com> Acked-by:
-
Paolo Abeni authored
syzbot was able to trigger an Out-of-Bound on the pedit action: UBSAN: shift-out-of-bounds in net/sched/act_pedit.c:238:43 shift exponent 1400735974 is too large for 32-bit type 'unsigned int' CPU: 0 PID: 3606 Comm: syz-executor151 Not tainted 5.18.0-rc5-syzkaller-00165-g810c2f0a #0 Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011 Call Trace: <TASK> __dump_stack lib/dump_stack.c:88 [inline] dump_stack_lvl+0xcd/0x134 lib/dump_stack.c:106 ubsan_epilogue+0xb/0x50 lib/ubsan.c:151 __ubsan_handle_shift_out_of_bounds.cold+0xb1/0x187 lib/ubsan.c:322 tcf_pedit_init.cold+0x1a/0x1f net/sched/act_pedit.c:238 tcf_action_init_1+0x414/0x690 net/sched/act_api.c:1367 tcf_action_init+0x530/0x8d0 net/sched/act_api.c:1432 tcf_action_add+0xf9/0x480 net/sched/act_api.c:1956 tc_ctl_action+0x346/0x470 net/sched/act_api.c:2015 rtnetlink_rcv_msg+0x413/0xb80 net/core/rtnetlink.c:5993 netlink_rcv_skb+0x153/0x420 net/netlink/af_netlink.c:2502 netlink_unicast_kernel net/netlink/af_netlink.c:1319 [inline] netlink_unicast+0x543/0x7f0 net/netlink/af_netlink.c:1345 netlink_sendmsg+0x904/0xe00 net/netlink/af_netlink.c:1921 sock_sendmsg_nosec net/socket.c:705 [inline] sock_sendmsg+0xcf/0x120 net/socket.c:725 ____sys_sendmsg+0x6e2/0x800 net/socket.c:2413 ___sys_sendmsg+0xf3/0x170 net/socket.c:2467 __sys_sendmsg+0xe5/0x1b0 net/socket.c:2496 do_syscall_x64 arch/x86/entry/common.c:50 [inline] do_syscall_64+0x35/0xb0 arch/x86/entry/common.c:80 entry_SYSCALL_64_after_hwframe+0x44/0xae RIP: 0033:0x7fe36e9e1b59 Code: 28 c3 e8 2a 14 00 00 66 2e 0f 1f 84 00 00 00 00 00 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff ff 73 01 c3 48 c7 c1 c0 ff ff ff f7 d8 64 89 01 48 RSP: 002b:00007ffef796fe88 EFLAGS: 00000246 ORIG_RAX: 000000000000002e RAX: ffffffffffffffda RBX: 0000000000000000 RCX: 00007fe36e9e1b59 RDX: 0000000000000000 RSI: 0000000020000300 RDI: 0000000000000003 RBP: 00007fe36e9a5d00 R08: 0000000000000000 R09: 0000000000000000 R10: 0000000000000000 R11: 0000000000000246 R12: 00007fe36e9a5d90 R13: 0000000000000000 R14: 0000000000000000 R15: 0000000000000000 </TASK> The 'shift' field is not validated, and any value above 31 will trigger out-of-bounds. The issue predates the git history, but syzbot was able to trigger it only after the commit mentioned in the fixes tag, and this change only applies on top of such commit. Address the issue bounding the 'shift' value to the maximum allowed by the relevant operator. Reported-and-tested-by: syzbot+8ed8fc4c57e9dcf23ca6@syzkaller.appspotmail.com Fixes: 8b796475 ("net/sched: act_pedit: really ensure the skb is writable") Signed-off-by:
David S. Miller <davem@davemloft.net>
-
David S. Miller authored
Merge tag 'linux-can-fixes-for-5.18-20220514' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can Marc Kleine-Budde says: ==================== pull-request: can 2022-05-14 this is a pull request of 2 patches for net/master. Changes to linux-can-fixes-for-5.18-20220513: - adjusted Fixes: Tag on "Revert "can: m_can: pci: use custom bit timings for Elkhart Lake"" (Thanks Jakub) Both patches are by Jarkko Nikula, target the m_can PCI driver bindings, and fix usage of wrong bit timing constants for the Elkhart Lake platform. ==================== Signed-off-by:
-
- 14 May, 2022 6 commits
-
-
Jarkko Nikula authored
Now when Intel Elkhart Lake uses again common bit timing and there are no other users for custom bit timing, we can bring back the changes done by the commit 0ddd83fb ("can: m_can: remove support for custom bit timing"). This effectively reverts commit ea768b2f ("Revert "can: m_can: remove support for custom bit timing"") while taking into account commit ea22ba40 ("can: m_can: make custom bittiming fields const") and commit 7d4a101c ("can: dev: add sanity check in can_set_static_ctrlmode()"). Link: https://lore.kernel.org/all/20220512124144.536850-2-jarkko.nikula@linux.intel.comSigned-off-by:
Jarkko Nikula <jarkko.nikula@linux.intel.com> Signed-off-by:
Marc Kleine-Budde <mkl@pengutronix.de>
-
Jarkko Nikula authored
This reverts commit 0e8ffdf3b86dfd44b651f91b12fcae76c25c453b. Commit 0e8ffdf3b86d ("can: m_can: pci: use custom bit timings for Elkhart Lake") broke the test case using bitrate switching. | ip link set can0 up type can bitrate 500000 dbitrate 4000000 fd on | ip link set can1 up type can bitrate 500000 dbitrate 4000000 fd on | candump can0 & | cangen can1 -I 0x800 -L 64 -e -fb \ | -D 11223344deadbeef55667788feedf00daabbccdd44332211 -n 1 -v -v Above commit does everything correctly according to the datasheet. However datasheet wasn't correct. I got confirmation from hardware engineers that the actual CAN hardware on Intel Elkhart Lake is based on M_CAN version v3.2.0. Datasheet was mirroring values from an another specification which was based on earlier M_CAN version leading to wrong bit timings. Therefore revert the commit and switch back to common bit timings. Fixes: ea4c1787 ("can: m_can: pci: use custom bit timings for Elkhart Lake") Link: https://lore.kernel.org/all/20220512124144.536850-1-jarkko.nikula@linux.intel.comSigned-off-by:Chee Hou Ong <chee.houx.ong@intel.com> Reported-by:
Aman Kumar <aman.kumar@intel.com> Reported-by:
Pallavi Kumari <kumari.pallavi@intel.com> Cc: <stable@vger.kernel.org> # v5.16+ Signed-off-by:
-
Harini Katakam authored
In gem_rx_refill rx_prepared_head is incremented at the beginning of the while loop preparing the skb and data buffers. If the skb or data buffer allocation fails, this BD will be unusable BDs until the head loops back to the same BD (and obviously buffer allocation succeeds). In the unlikely event that there's a string of allocation failures, there will be an equal number of unusable BDs and an inconsistent RX BD chain. Hence increment the head at the end of the while loop to be clean. Fixes: 4df95131 ("net/macb: change RX path for GEM") Signed-off-by:
Harini Katakam <harini.katakam@xilinx.com> Signed-off-by:
Michal Simek <michal.simek@xilinx.com> Signed-off-by:
Radhey Shyam Pandey <radhey.shyam.pandey@xilinx.com> Reviewed-by:
Claudiu Beznea <claudiu.beznea@microchip.com> Link: https://lore.kernel.org/r/20220512171900.32593-1-harini.katakam@xilinx.comSigned-off-by:
-
Jakub Kicinski authored
Mat Martineau says: ==================== mptcp: Subflow accounting fix This series contains a bug fix affecting the in-kernel path manager (patch 1), where closing subflows would sometimes not adjust the PM's count of active subflows. Patch 2 updates the selftests to exercise the new code. ==================== Link: https://lore.kernel.org/r/20220512232642.541301-1-mathew.j.martineau@linux.intel.comSigned-off-by:
-
Paolo Abeni authored
Add and delete a bunch of endpoints and verify the respect of configured limits. This covers the codepath introduced by the previous patch. Fixes: 69c6ce7b ("selftests: mptcp: add implicit endpoint test case") Signed-off-by:
Mat Martineau <mathew.j.martineau@linux.intel.com> Signed-off-by:
-
Paolo Abeni authored
If the PM closes a fully established MPJ subflow or the subflow creation errors out in it's early stage the subflows counter is not bumped accordingly. This change adds the missing accounting, additionally taking care of updating accordingly the 'accept_subflow' flag. Fixes: a88c9e49 ("mptcp: do not block subflows creation on errors") Signed-off-by:
-
- 13 May, 2022 5 commits
-
-
Eric Dumazet authored
This reverts commits: 0dad4087 ("tcp/dccp: get rid of inet_twsk_purge()") d507204d ("tcp/dccp: add tw->tw_bslot") As Leonard pointed out, a newly allocated netns can happen to reuse a freed 'struct net'. While TCP TW timers were covered by my patches, other things were not: 1) Lookups in rx path (INET_MATCH() and INET6_MATCH()), as they look at 4-tuple plus the 'struct net' pointer. 2) /proc/net/tcp[6] and inet_diag, same reason. 3) hashinfo->bhash[], same reason. Fixing all this seems risky, lets instead revert. In the future, we might have a per netns tcp hash table, or a per netns list of timewait sockets... Fixes: 0dad4087 ("tcp/dccp: get rid of inet_twsk_purge()") Signed-off-by:
Leonard Crestez <cdleonard@gmail.com> Tested-by:
-
David S. Miller authored
Alex Elder says: ==================== net: ipa: three bug fixes This series contains three somewhat unrelated minor bug fixes. ==================== Signed-off-by: -
Alex Elder authored
In ipa_qmi_ready(), the "ipa" local variable is set when initialized, but then set again just before it's first used. One or the other is enough, so get rid of the first one. References: https://lore.kernel.org/lkml/200de1bd-0f01-c334-ca18-43eed783dfac@intel.com/Reported-by:
kernel test robot <lkp@intel.com> Fixes: 530f9216 ("soc: qcom: ipa: AP/modem communications") Signed-off-by:
Alex Elder <elder@linaro.org> Signed-off-by:
-
Alex Elder authored
Each time we are notified that some number of transactions on an RX channel has completed, we record the number of bytes that have been transferred since the previous notification. We also track the number of transactions completed, but that is not currently being calculated correctly; we're currently counting the number of such notifications, but each notification can represent many transaction completions. Fix this. Fixes: 650d1603 ("soc: qcom: ipa: the generic software interface") Signed-off-by:
-
Alex Elder authored
If an RX endpoint receives packets containing status headers, and a packet in the buffer is not dropped, ipa_endpoint_skb_copy() is responsible for wrapping the packet data in an SKB and forwarding it to ipa_modem_skb_rx() for further processing. If ipa_endpoint_skb_copy() gets a null pointer from build_skb(), it just returns early. But in the process it doesn't record that as a dropped packet in the network device statistics. Instead, call ipa_modem_skb_rx() whether or not the SKB pointer is NULL; that function ensures the statistics are properly updated. Fixes: 1b65bbcc ("net: ipa: skip SKB copy if no netdev") Signed-off-by:
-
- 12 May, 2022 13 commits
-
-
git://git.kernel.org/pub/scm/linux/kernel/git/netdev/netLinus Torvalds authored
Pull networking fixes from Jakub Kicinski: "Including fixes from wireless, and bluetooth. No outstanding fires. Current release - regressions: - eth: atlantic: always deep reset on pm op, fix null-deref Current release - new code bugs: - rds: use maybe_get_net() when acquiring refcount on TCP sockets [refinement of a previous fix] - eth: ocelot: mark traps with a bool instead of guessing type based on list membership Previous releases - regressions: - net: fix skipping features in for_each_netdev_feature() - phy: micrel: fix null-derefs on suspend/resume and probe - bcmgenet: check for Wake-on-LAN interrupt probe deferral Previous releases - always broken: - ipv4: drop dst in multicast routing path, prevent leaks - ping: fix address binding wrt vrf - net: fix wrong network header length when BPF protocol translation is used on skbs with a fraglist - bluetooth: fix the creation of hdev->name - rfkill: uapi: fix RFKILL_IOCTL_MAX_SIZE ioctl request definition - wifi: iwlwifi: iwl-dbg: use del_timer_sync() before freeing - wifi: ath11k: reduce the wait time of 11d scan and hw scan while adding an interface - mac80211: fix rx reordering with non explicit / psmp ack policy - mac80211: reset MBSSID parameters upon connection - nl80211: fix races in nl80211_set_tx_bitrate_mask() - tls: fix context leak on tls_device_down - sched: act_pedit: really ensure the skb is writable - batman-adv: don't skb_split skbuffs with frag_list - eth: ocelot: fix various issues with TC actions (null-deref; bad stats; ineffective drops; ineffective filter removal)" * tag 'net-5.18-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (61 commits) tls: Fix context leak on tls_device_down net: sfc: ef10: fix memory leak in efx_ef10_mtd_probe() net/smc: non blocking recvmsg() return -EAGAIN when no data and signal_pending net: dsa: bcm_sf2: Fix Wake-on-LAN with mac_link_down() mlxsw: Avoid warning during ip6gre device removal net: bcmgenet: Check for Wake-on-LAN interrupt probe deferral net: ethernet: mediatek: ppe: fix wrong size passed to memset() Bluetooth: Fix the creation of hdev->name i40e: i40e_main: fix a missing check on list iterator net/sched: act_pedit: really ensure the skb is writable s390/lcs: fix variable dereferenced before check s390/ctcm: fix potential memory leak s390/ctcm: fix variable dereferenced before check net: atlantic: verify hw_head_ lies within TX buffer ring net: atlantic: add check for MAX_SKB_FRAGS net: atlantic: reduce scope of is_rsc_complete net: atlantic: fix "frag[0] not initialized" net: stmmac: fix missing pci_disable_device() on error in stmmac_pci_probe() net: phy: micrel: Fix incorrect variable type in micrel decnet: Use container_of() for struct dn_neigh casts ... -
git://git.kernel.org/pub/scm/linux/kernel/git/tj/cgroupLinus Torvalds authored
Pull cgroup fix from Tejun Heo: "Waiman's fix for a cgroup2 cpuset bug where it could miss nodes which were hot-added" * 'for-5.18-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/cgroup: cgroup/cpuset: Remove cpus_allowed/mems_allowed setup in cpuset_init_smp()
-
git://git.kernel.org/pub/scm/linux/kernel/git/jack/linux-fsLinus Torvalds authored
Pull fs fixes from Jan Kara: "Three fixes that I'd still like to get to 5.18: - add a missing sanity check in the fanotify FAN_RENAME feature (added in 5.17, let's fix it before it gets wider usage in userspace) - udf fix for recently introduced filesystem corruption issue - writeback fix for a race in inode list handling that can lead to delayed writeback and possible dirty throttling stalls" * tag 'fixes_for_v5.18-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/jack/linux-fs: udf: Avoid using stale lengthOfImpUse writeback: Avoid skipping inode writeback fanotify: do not allow setting dirent events in mask of non-dir -
Maxim Mikityanskiy authored
The commit cited below claims to fix a use-after-free condition after tls_device_down. Apparently, the description wasn't fully accurate. The context stayed alive, but ctx->netdev became NULL, and the offload was torn down without a proper fallback, so a bug was present, but a different kind of bug. Due to misunderstanding of the issue, the original patch dropped the refcount_dec_and_test line for the context to avoid the alleged premature deallocation. That line has to be restored, because it matches the refcount_inc_not_zero from the same function, otherwise the contexts that survived tls_device_down are leaked. This patch fixes the described issue by restoring refcount_dec_and_test. After this change, there is no leak anymore, and the fallback to software kTLS still works. Fixes: c55dcdd4 ("net/tls: Fix use-after-free after the TLS device goes down and up") Signed-off-by:
-
Taehee Yoo authored
In the NIC ->probe() callback, ->mtd_probe() callback is called. If NIC has 2 ports, ->probe() is called twice and ->mtd_probe() too. In the ->mtd_probe(), which is efx_ef10_mtd_probe() it allocates and initializes mtd partiion. But mtd partition for sfc is shared data. So that allocated mtd partition data from last called efx_ef10_mtd_probe() will not be used. Therefore it must be freed. But it doesn't free a not used mtd partition data in efx_ef10_mtd_probe(). kmemleak reports: unreferenced object 0xffff88811ddb0000 (size 63168): comm "systemd-udevd", pid 265, jiffies 4294681048 (age 348.586s) hex dump (first 32 bytes): 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................ 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................ backtrace: [<ffffffffa3767749>] kmalloc_order_trace+0x19/0x120 [<ffffffffa3873f0e>] __kmalloc+0x20e/0x250 [<ffffffffc041389f>] efx_ef10_mtd_probe+0x11f/0x270 [sfc] [<ffffffffc0484c8a>] efx_pci_probe.cold.17+0x3df/0x53d [sfc] [<ffffffffa414192c>] local_pci_probe+0xdc/0x170 [<ffffffffa4145df5>] pci_device_probe+0x235/0x680 [<ffffffffa443dd52>] really_probe+0x1c2/0x8f0 [<ffffffffa443e72b>] __driver_probe_device+0x2ab/0x460 [<ffffffffa443e92a>] driver_probe_device+0x4a/0x120 [<ffffffffa443f2ae>] __driver_attach+0x16e/0x320 [<ffffffffa4437a90>] bus_for_each_dev+0x110/0x190 [<ffffffffa443b75e>] bus_add_driver+0x39e/0x560 [<ffffffffa4440b1e>] driver_register+0x18e/0x310 [<ffffffffc02e2055>] 0xffffffffc02e2055 [<ffffffffa3001af3>] do_one_initcall+0xc3/0x450 [<ffffffffa33ca574>] do_init_module+0x1b4/0x700 Acked-by:Martin Habets <habetsm.xilinx@gmail.com> Fixes: 8127d661 ("sfc: Add support for Solarflare SFC9100 family") Signed-off-by:
Taehee Yoo <ap420073@gmail.com> Link: https://lore.kernel.org/r/20220512054709.12513-1-ap420073@gmail.comSigned-off-by:
-
Guangguan Wang authored
Non blocking sendmsg will return -EAGAIN when any signal pending and no send space left, while non blocking recvmsg return -EINTR when signal pending and no data received. This may makes confused. As TCP returns -EAGAIN in the conditions described above. Align the behavior of smc with TCP. Fixes: 846e344e ("net/smc: add receive timeout check") Signed-off-by:
Guangguan Wang <guangguan.wang@linux.alibaba.com> Reviewed-by:
Tony Lu <tonylu@linux.alibaba.com> Acked-by:
Karsten Graul <kgraul@linux.ibm.com> Link: https://lore.kernel.org/r/20220512030820.73848-1-guangguan.wang@linux.alibaba.comSigned-off-by:
-
Florian Fainelli authored
After commit 2d1f90f9 ("net: dsa/bcm_sf2: fix incorrect usage of state->link") the interface suspend path would call our mac_link_down() call back which would forcibly set the link down, thus preventing Wake-on-LAN packets from reaching our management port. Fix this by looking at whether the port is enabled for Wake-on-LAN and not clearing the link status in that case to let packets go through. Fixes: 2d1f90f9 ("net: dsa/bcm_sf2: fix incorrect usage of state->link") Signed-off-by:
-
Amit Cohen authored
IPv6 addresses which are used for tunnels are stored in a hash table with reference counting. When a new GRE tunnel is configured, the driver is notified and configures it in hardware. Currently, any change in the tunnel is not applied in the driver. It means that if the remote address is changed, the driver is not aware of this change and the first address will be used. This behavior results in a warning [1] in scenarios such as the following: # ip link add name gre1 type ip6gre local 2000::3 remote 2000::fffe tos inherit ttl inherit # ip link set name gre1 type ip6gre local 2000::3 remote 2000::ffff ttl inherit # ip link delete gre1 The change of the address is not applied in the driver. Currently, the driver uses the remote address which is stored in the 'parms' of the overlay device. When the tunnel is removed, the new IPv6 address is used, the driver tries to release it, but as it is not aware of the change, this address is not configured and it warns about releasing non existing IPv6 address. Fix it by using the IPv6 address which is cached in the IPIP entry, this address is the last one that the driver used, so even in cases such the above, the first address will be released, without any warning. [1]: WARNING: CPU: 1 PID: 2197 at drivers/net/ethernet/mellanox/mlxsw/spectrum.c:2920 mlxsw_sp_ipv6_addr_put+0x146/0x220 [mlxsw_spectrum] ... CPU: 1 PID: 2197 Comm: ip Not tainted 5.17.0-rc8-custom-95062-gc1e5ded51a9a #84 Hardware name: Mellanox Technologies Ltd. MSN4700/VMOD0010, BIOS 5.11 07/12/2021 RIP: 0010:mlxsw_sp_ipv6_addr_put+0x146/0x220 [mlxsw_spectrum] ... Call Trace: <TASK> mlxsw_sp2_ipip_rem_addr_unset_gre6+0xf1/0x120 [mlxsw_spectrum] mlxsw_sp_netdevice_ipip_ol_event+0xdb/0x640 [mlxsw_spectrum] mlxsw_sp_netdevice_event+0xc4/0x850 [mlxsw_spectrum] raw_notifier_call_chain+0x3c/0x50 call_netdevice_notifiers_info+0x2f/0x80 unregister_netdevice_many+0x311/0x6d0 rtnl_dellink+0x136/0x360 rtnetlink_rcv_msg+0x12f/0x380 netlink_rcv_skb+0x49/0xf0 netlink_unicast+0x233/0x340 netlink_sendmsg+0x202/0x440 ____sys_sendmsg+0x1f3/0x220 ___sys_sendmsg+0x70/0xb0 __sys_sendmsg+0x54/0xa0 do_syscall_64+0x35/0x80 entry_SYSCALL_64_after_hwframe+0x44/0xae Fixes: e846efe2 ("mlxsw: spectrum: Add hash table for IPv6 address mapping") Reported-by:
Maksym Yaremchuk <maksymy@nvidia.com> Signed-off-by:
Amit Cohen <amcohen@nvidia.com> Signed-off-by:
Ido Schimmel <idosch@nvidia.com> Link: https://lore.kernel.org/r/20220511115747.238602-1-idosch@nvidia.comSigned-off-by:
-
Florian Fainelli authored
The interrupt controller supplying the Wake-on-LAN interrupt line maybe modular on some platforms (irq-bcm7038-l1.c) and might be probed at a later time than the GENET driver. We need to specifically check for -EPROBE_DEFER and propagate that error to ensure that we eventually fetch the interrupt descriptor. Fixes: 9deb48b5 ("bcmgenet: add WOL IRQ check") Fixes: 5b1f0e62 ("net: bcmgenet: Avoid touching non-existent interrupt") Signed-off-by:
Stefan Wahren <stefan.wahren@i2se.com> Link: https://lore.kernel.org/r/20220511031752.2245566-1-f.fainelli@gmail.comSigned-off-by:
-
Yang Yingliang authored
'foe_table' is a pointer, the real size of struct mtk_foe_entry should be pass to memset(). Fixes: ba37b7ca ("net: ethernet: mtk_eth_soc: add support for initializing the PPE") Signed-off-by:
Yang Yingliang <yangyingliang@huawei.com> Acked-by:
Felix Fietkau <nbd@nbd.name> Link: https://lore.kernel.org/r/20220511030829.3308094-1-yangyingliang@huawei.comSigned-off-by:
-
git://git.kernel.org/pub/scm/linux/kernel/git/bluetooth/bluetoothJakub Kicinski authored
Luiz Augusto von Dentz says: ==================== bluetooth pull request for net: - Fix the creation of hdev->name when index is greater than 9999 * tag 'for-net-2022-05-11' of git://git.kernel.org/pub/scm/linux/kernel/git/bluetooth/bluetooth: Bluetooth: Fix the creation of hdev->name ==================== Link: https://lore.kernel.org/r/20220512002901.823647-1-luiz.dentz@gmail.comSigned-off-by:
-
git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wirelessJakub Kicinski authored
Kalle Valo says: ==================== wireless fixes for v5.18 Second set of fixes for v5.18 and hopefully the last one. We have a new iwlwifi maintainer, a fix to rfkill ioctl interface and important fixes to both stack and two drivers. * tag 'wireless-2022-05-11' of git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless: rfkill: uapi: fix RFKILL_IOCTL_MAX_SIZE ioctl request definition nl80211: fix locking in nl80211_set_tx_bitrate_mask() mac80211_hwsim: call ieee80211_tx_prepare_skb under RCU protection mac80211_hwsim: fix RCU protected chanctx access mailmap: update Kalle Valo's email mac80211: Reset MBSSID parameters upon connection cfg80211: retrieve S1G operating channel number nl80211: validate S1G channel width mac80211: fix rx reordering with non explicit / psmp ack policy ath11k: reduce the wait time of 11d scan and hw scan while add interface MAINTAINERS: update iwlwifi driver maintainer iwlwifi: iwl-dbg: Use del_timer_sync() before freeing ==================== Link: https://lore.kernel.org/r/20220511154535.A1A12C340EE@smtp.kernel.orgSigned-off-by:
-
Itay Iellin authored
Set a size limit of 8 bytes of the written buffer to "hdev->name" including the terminating null byte, as the size of "hdev->name" is 8 bytes. If an id value which is greater than 9999 is allocated, then the "snprintf(hdev->name, sizeof(hdev->name), "hci%d", id)" function call would lead to a truncation of the id value in decimal notation. Set an explicit maximum id parameter in the id allocation function call. The id allocation function defines the maximum allocated id value as the maximum id parameter value minus one. Therefore, HCI_MAX_ID is defined as 10000. Signed-off-by:
Itay Iellin <ieitayie@gmail.com> Signed-off-by:
Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
-
- 11 May, 2022 1 commit
-
-
Xiaomeng Tong authored
The bug is here: ret = i40e_add_macvlan_filter(hw, ch->seid, vdev->dev_addr, &aq_err); The list iterator 'ch' will point to a bogus position containing HEAD if the list is empty or no element is found. This case must be checked before any use of the iterator, otherwise it will lead to a invalid memory access. To fix this bug, use a new variable 'iter' as the list iterator, while use the origin variable 'ch' as a dedicated pointer to point to the found element. Cc: stable@vger.kernel.org Fixes: 1d8d80b4 ("i40e: Add macvlan support on i40e") Signed-off-by:
Xiaomeng Tong <xiam0nd.tong@gmail.com> Tested-by: Gurucharan <gurucharanx.g@intel.com> (A Contingent worker at Intel) Signed-off-by:
Tony Nguyen <anthony.l.nguyen@intel.com> Link: https://lore.kernel.org/r/20220510204846.2166999-1-anthony.l.nguyen@intel.comSigned-off-by:
-
