- 03 Apr, 2019 2 commits
-
-
Marcel Holtmann authored
commit 7c9cbd0b upstream. The function l2cap_get_conf_opt will return L2CAP_CONF_OPT_SIZE + opt->len as length value. The opt->len however is in control over the remote user and can be used by an attacker to gain access beyond the bounds of the actual packet. To prevent any potential leak of heap memory, it is enough to check that the resulting len calculation after calling l2cap_get_conf_opt is not below zero. A well formed packet will always return >= 0 here and will end with the length value being zero after the last option has been parsed. In case of malformed packets messing with the opt->len field the length value will become negative. If that is the case, then just abort and ignore the option. In case an attacker uses a too short opt->len value, then garbage will be parsed, but that is protected by the unknown option handling and also the option parameter size checks. Signed-off-by:
Marcel Holtmann <marcel@holtmann.org> Reviewed-by:
Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by:
Johan Hedberg <johan.hedberg@intel.com> Signed-off-by:
-
Marcel Holtmann authored
commit af3d5d1c upstream. When doing option parsing for standard type values of 1, 2 or 4 octets, the value is converted directly into a variable instead of a pointer. To avoid being tricked into being a pointer, check that for these option types that sizes actually match. In L2CAP every option is fixed size and thus it is prudent anyway to ensure that the remote side sends us the right option size along with option paramters. If the option size is not matching the option type, then that option is silently ignored. It is a protocol violation and instead of trying to give the remote attacker any further hints just pretend that option is not present and proceed with the default values. Implementation following the specification and its qualification procedures will always use the correct size and thus not being impacted here. To keep the code readable and consistent accross all options, a few cosmetic changes were also required. Signed-off-by:
-
- 27 Mar, 2019 38 commits
-
-
Greg Kroah-Hartman authored
-
Baolin Wang authored
commit f25a646f upstream. Fix incorrect return value. Signed-off-by:
Baolin Wang <baolin.wang@linaro.org> Signed-off-by:
Sebastian Reichel <sebastian.reichel@collabora.com> Signed-off-by:
-
Hui Wang authored
commit b5a236c1 upstream. Recently we found the audio jack detection stop working after suspend on many machines with Realtek codec. Sometimes the audio selection dialogue didn't show up after users plugged headhphone/headset into the headset jack, sometimes after uses plugged headphone/headset, then click the sound icon on the upper-right corner of gnome-desktop, it also showed the speaker rather than the headphone. The root cause is that before suspend, the codec already call the runtime_suspend since this codec is not used by any apps, then in resume, it will not call runtime_resume for this codec. But for some realtek codec (so far, alc236, alc255 and alc891) with the specific BIOS, if it doesn't run runtime_resume after suspend, all codec functions including jack detection stop working anymore. This problem existed for a long time, but it was not exposed, that is because when problem happens, if users play sound or open sound-setting to check audio device, this will trigger calling to runtime_resume (via snd_hda_power_up), then the codec starts working again before users notice this problem. Since we don't know how many codec and BIOS combinations have this problem, to fix it, let the driver call runtime_resume for all codecs in pm_resume, maybe for some codecs, this is not needed, but it is harmless. After a codec is runtime resumed, if it is not used by any apps, it will be runtime suspended soon and furthermore we don't run suspend frequently, this change will not add much power consumption. Fixes: cc72da7d ("ALSA: hda - Use standard runtime PM for codec power-save control") Signed-off-by:
Hui Wang <hui.wang@canonical.com> Signed-off-by:
Takashi Iwai <tiwai@suse.de> Signed-off-by:
-
Takashi Iwai authored
commit 98081ca6 upstream. Currently we deal with single codec and suspend codec callbacks for all S3, S4 and runtime PM handling. But it turned out that we want distinguish the call patterns sometimes, e.g. for applying some init sequence only at probing and restoring from hibernate. This patch slightly modifies the common PM callbacks for HD-audio codec and stores the currently processed PM event in power_state of the codec's device.power field, which is currently unused. The codec callback can take a look at this event value and judges which purpose it's being called. Signed-off-by:
-
Waiman Long authored
commit 71492580 upstream. Tetsuo Handa had reported he saw an incorrect "downgrading a read lock" warning right after a previous lockdep warning. It is likely that the previous warning turned off lock debugging causing the lockdep to have inconsistency states leading to the lock downgrade warning. Fix that by add a check for debug_locks at the beginning of __lock_downgrade(). Debugged-by:
Tetsuo Handa <penguin-kernel@i-love.sakura.ne.jp> Reported-by:
Waiman Long <longman@redhat.com> Signed-off-by:
Peter Zijlstra (Intel) <peterz@infradead.org> Cc: Andrew Morton <akpm@linux-foundation.org> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Will Deacon <will.deacon@arm.com> Link: https://lkml.kernel.org/r/1547093005-26085-1-git-send-email-longman@redhat.comSigned-off-by:
Ingo Molnar <mingo@kernel.org> Signed-off-by:
-
Jann Horn authored
commit ac5ceccc upstream. When the ORC unwinder is invoked for an oops caused by IP==0, it currently has no idea what to do because there is no debug information for the stack frame of NULL. But if RIP is NULL, it is very likely that the last successfully executed instruction was an indirect CALL/JMP, and it is possible to unwind out in the same way as for the first instruction of a normal function. Hardcode a corresponding ORC entry. With an artificially-added NULL call in prctl_set_seccomp(), before this patch, the trace is: Call Trace: ? __x64_sys_prctl+0x402/0x680 ? __ia32_sys_prctl+0x6e0/0x6e0 ? __do_page_fault+0x457/0x620 ? do_syscall_64+0x6d/0x160 ? entry_SYSCALL_64_after_hwframe+0x44/0xa9 After this patch, the trace looks like this: Call Trace: __x64_sys_prctl+0x402/0x680 ? __ia32_sys_prctl+0x6e0/0x6e0 ? __do_page_fault+0x457/0x620 do_syscall_64+0x6d/0x160 entry_SYSCALL_64_after_hwframe+0x44/0xa9 prctl_set_seccomp() still doesn't show up in the trace because for some reason, tail call optimization is only disabled in builds that use the frame pointer unwinder. Signed-off-by:
Jann Horn <jannh@google.com> Signed-off-by:
Thomas Gleixner <tglx@linutronix.de> Acked-by:
Josh Poimboeuf <jpoimboe@redhat.com> Cc: Borislav Petkov <bp@alien8.de> Cc: Andrew Morton <akpm@linux-foundation.org> Cc: syzbot <syzbot+ca95b2b7aef9e7cbd6ab@syzkaller.appspotmail.com> Cc: "H. Peter Anvin" <hpa@zytor.com> Cc: Masahiro Yamada <yamada.masahiro@socionext.com> Cc: Michal Marek <michal.lkml@markovi.net> Cc: linux-kbuild@vger.kernel.org Link: https://lkml.kernel.org/r/20190301031201.7416-2-jannh@google.comSigned-off-by:
-
Jann Horn authored
commit f4f34e1b upstream. When the frame unwinder is invoked for an oops caused by a call to NULL, it currently skips the parent function because BP still points to the parent's stack frame; the (nonexistent) current function only has the first half of a stack frame, and BP doesn't point to it yet. Add a special case for IP==0 that calculates a fake BP from SP, then uses the real BP for the next frame. Note that this handles first_frame specially: Return information about the parent function as long as the saved IP is >=first_frame, even if the fake BP points below it. With an artificially-added NULL call in prctl_set_seccomp(), before this patch, the trace is: Call Trace: ? prctl_set_seccomp+0x3a/0x50 __x64_sys_prctl+0x457/0x6f0 ? __ia32_sys_prctl+0x750/0x750 do_syscall_64+0x72/0x160 entry_SYSCALL_64_after_hwframe+0x44/0xa9 After this patch, the trace is: Call Trace: prctl_set_seccomp+0x3a/0x50 __x64_sys_prctl+0x457/0x6f0 ? __ia32_sys_prctl+0x750/0x750 do_syscall_64+0x72/0x160 entry_SYSCALL_64_after_hwframe+0x44/0xa9 Signed-off-by:
-
Dongli Zhang authored
commit f7c8a412 upstream. Commit 758a58d0 ("loop: set GENHD_FL_NO_PART_SCAN after blkdev_reread_part()") separates "lo->lo_backing_file = NULL" and "lo->lo_state = Lo_unbound" into different critical regions protected by loop_ctl_mutex. However, there is below race that the NULL lo->lo_backing_file would be accessed when the backend of a loop is another loop device, e.g., loop0's backend is a file, while loop1's backend is loop0. loop0's backend is file loop1's backend is loop0 __loop_clr_fd() mutex_lock(&loop_ctl_mutex); lo->lo_backing_file = NULL; --> set to NULL mutex_unlock(&loop_ctl_mutex); loop_set_fd() mutex_lock_killable(&loop_ctl_mutex); loop_validate_file() f = l->lo_backing_file; --> NULL access if loop0 is not Lo_unbound mutex_lock(&loop_ctl_mutex); lo->lo_state = Lo_unbound; mutex_unlock(&loop_ctl_mutex); lo->lo_backing_file should be accessed only when the loop device is Lo_bound. In fact, the problem has been introduced already in commit 7ccd0791 ("loop: Push loop_ctl_mutex down into loop_clr_fd()") after which loop_validate_file() could see devices in Lo_rundown state with which it did not count. It was harmless at that point but still. Fixes: 7ccd0791 ("loop: Push loop_ctl_mutex down into loop_clr_fd()") Reported-by: syzbot+9bdc1adc1c55e7fe765b@syzkaller.appspotmail.com Signed-off-by:
Dongli Zhang <dongli.zhang@oracle.com> Reviewed-by:
Jan Kara <jack@suse.cz> Signed-off-by:
Jens Axboe <axboe@kernel.dk> Signed-off-by:
-
Florian Westphal authored
commit d824548d upstream. They are however frequently triggered by syzkaller, so remove them. ebtables userspace should never trigger any of these, so there is little value in making them pr_debug (or ratelimited). Signed-off-by:
Florian Westphal <fw@strlen.de> Signed-off-by:
Pablo Neira Ayuso <pablo@netfilter.org> Signed-off-by:
-
Chao Yu authored
commit 48432984 upstream. Thread A Thread B - __fput - f2fs_release_file - drop_inmem_pages - mutex_lock(&fi->inmem_lock) - __revoke_inmem_pages - lock_page(page) - open - f2fs_setattr - truncate_setsize - truncate_inode_pages_range - lock_page(page) - truncate_cleanup_page - f2fs_invalidate_page - drop_inmem_page - mutex_lock(&fi->inmem_lock); We may encounter above ABBA deadlock as reported by Kyungtae Kim: I'm reporting a bug in linux-4.17.19: "INFO: task hung in drop_inmem_page" (no reproducer) I think this might be somehow related to the following: https://groups.google.com/forum/#!searchin/syzkaller-bugs/INFO$3A$20task$20hung$20in$20%7Csort:date/syzkaller-bugs/c6soBTrdaIo/AjAzPeIzCgAJ ========================================= INFO: task syz-executor7:10822 blocked for more than 120 seconds. Not tainted 4.17.19 #1 "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message. syz-executor7 D27024 10822 6346 0x00000004 Call Trace: context_switch kernel/sched/core.c:2867 [inline] __schedule+0x721/0x1e60 kernel/sched/core.c:3515 schedule+0x88/0x1c0 kernel/sched/core.c:3559 schedule_preempt_disabled+0x18/0x30 kernel/sched/core.c:3617 __mutex_lock_common kernel/locking/mutex.c:833 [inline] __mutex_lock+0x5bd/0x1410 kernel/locking/mutex.c:893 mutex_lock_nested+0x1b/0x20 kernel/locking/mutex.c:908 drop_inmem_page+0xcb/0x810 fs/f2fs/segment.c:327 f2fs_invalidate_page+0x337/0x5e0 fs/f2fs/data.c:2401 do_invalidatepage mm/truncate.c:165 [inline] truncate_cleanup_page+0x261/0x330 mm/truncate.c:187 truncate_inode_pages_range+0x552/0x1610 mm/truncate.c:367 truncate_inode_pages mm/truncate.c:478 [inline] truncate_pagecache+0x6d/0x90 mm/truncate.c:801 truncate_setsize+0x81/0xa0 mm/truncate.c:826 f2fs_setattr+0x44f/0x1270 fs/f2fs/file.c:781 notify_change+0xa62/0xe80 fs/attr.c:313 do_truncate+0x12e/0x1e0 fs/open.c:63 do_last fs/namei.c:2955 [inline] path_openat+0x2042/0x29f0 fs/namei.c:3505 do_filp_open+0x1bd/0x2c0 fs/namei.c:3540 do_sys_open+0x35e/0x4e0 fs/open.c:1101 __do_sys_open fs/open.c:1119 [inline] __se_sys_open fs/open.c:1114 [inline] __x64_sys_open+0x89/0xc0 fs/open.c:1114 do_syscall_64+0xc4/0x4e0 arch/x86/entry/common.c:287 entry_SYSCALL_64_after_hwframe+0x49/0xbe RIP: 0033:0x4497b9 RSP: 002b:00007f734e459c68 EFLAGS: 00000246 ORIG_RAX: 0000000000000002 RAX: ffffffffffffffda RBX: 00007f734e45a6cc RCX: 00000000004497b9 RDX: 0000000000000104 RSI: 00000000000a8280 RDI: 0000000020000080 RBP: 000000000071bea0 R08: 0000000000000000 R09: 0000000000000000 R10: 0000000000000000 R11: 0000000000000246 R12: 00000000ffffffff R13: 0000000000007230 R14: 00000000006f02d0 R15: 00007f734e45a700 INFO: task syz-executor7:10858 blocked for more than 120 seconds. Not tainted 4.17.19 #1 "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message. syz-executor7 D28880 10858 6346 0x00000004 Call Trace: context_switch kernel/sched/core.c:2867 [inline] __schedule+0x721/0x1e60 kernel/sched/core.c:3515 schedule+0x88/0x1c0 kernel/sched/core.c:3559 __rwsem_down_write_failed_common kernel/locking/rwsem-xadd.c:565 [inline] rwsem_down_write_failed+0x5e6/0xc90 kernel/locking/rwsem-xadd.c:594 call_rwsem_down_write_failed+0x17/0x30 arch/x86/lib/rwsem.S:117 __down_write arch/x86/include/asm/rwsem.h:142 [inline] down_write+0x58/0xa0 kernel/locking/rwsem.c:72 inode_lock include/linux/fs.h:713 [inline] do_truncate+0x120/0x1e0 fs/open.c:61 do_last fs/namei.c:2955 [inline] path_openat+0x2042/0x29f0 fs/namei.c:3505 do_filp_open+0x1bd/0x2c0 fs/namei.c:3540 do_sys_open+0x35e/0x4e0 fs/open.c:1101 __do_sys_open fs/open.c:1119 [inline] __se_sys_open fs/open.c:1114 [inline] __x64_sys_open+0x89/0xc0 fs/open.c:1114 do_syscall_64+0xc4/0x4e0 arch/x86/entry/common.c:287 entry_SYSCALL_64_after_hwframe+0x49/0xbe RIP: 0033:0x4497b9 RSP: 002b:00007f734e3b4c68 EFLAGS: 00000246 ORIG_RAX: 0000000000000002 RAX: ffffffffffffffda RBX: 00007f734e3b56cc RCX: 00000000004497b9 RDX: 0000000000000104 RSI: 00000000000a8280 RDI: 0000000020000080 RBP: 000000000071c238 R08: 0000000000000000 R09: 0000000000000000 R10: 0000000000000000 R11: 0000000000000246 R12: 00000000ffffffff R13: 0000000000007230 R14: 00000000006f02d0 R15: 00007f734e3b5700 INFO: task syz-executor5:10829 blocked for more than 120 seconds. Not tainted 4.17.19 #1 "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message. syz-executor5 D28760 10829 6308 0x80000002 Call Trace: context_switch kernel/sched/core.c:2867 [inline] __schedule+0x721/0x1e60 kernel/sched/core.c:3515 schedule+0x88/0x1c0 kernel/sched/core.c:3559 io_schedule+0x21/0x80 kernel/sched/core.c:5179 wait_on_page_bit_common mm/filemap.c:1100 [inline] __lock_page+0x2b5/0x390 mm/filemap.c:1273 lock_page include/linux/pagemap.h:483 [inline] __revoke_inmem_pages+0xb35/0x11c0 fs/f2fs/segment.c:231 drop_inmem_pages+0xa3/0x3e0 fs/f2fs/segment.c:306 f2fs_release_file+0x2c7/0x330 fs/f2fs/file.c:1556 __fput+0x2c7/0x780 fs/file_table.c:209 ____fput+0x1a/0x20 fs/file_table.c:243 task_work_run+0x151/0x1d0 kernel/task_work.c:113 exit_task_work include/linux/task_work.h:22 [inline] do_exit+0x8ba/0x30a0 kernel/exit.c:865 do_group_exit+0x13b/0x3a0 kernel/exit.c:968 get_signal+0x6bb/0x1650 kernel/signal.c:2482 do_signal+0x84/0x1b70 arch/x86/kernel/signal.c:810 exit_to_usermode_loop+0x155/0x190 arch/x86/entry/common.c:162 prepare_exit_to_usermode arch/x86/entry/common.c:196 [inline] syscall_return_slowpath arch/x86/entry/common.c:265 [inline] do_syscall_64+0x445/0x4e0 arch/x86/entry/common.c:290 entry_SYSCALL_64_after_hwframe+0x49/0xbe RIP: 0033:0x4497b9 RSP: 002b:00007f1c68e74ce8 EFLAGS: 00000246 ORIG_RAX: 00000000000000ca RAX: fffffffffffffe00 RBX: 000000000071bf80 RCX: 00000000004497b9 RDX: 0000000000000000 RSI: 0000000000000000 RDI: 000000000071bf80 RBP: 000000000071bf80 R08: 0000000000000000 R09: 000000000071bf58 R10: 0000000000000000 R11: 0000000000000246 R12: 0000000000000000 R13: 0000000000000000 R14: 00007f1c68e759c0 R15: 00007f1c68e75700 This patch tries to use trylock_page to mitigate such deadlock condition for fix. Signed-off-by:
Chao Yu <yuchao0@huawei.com> Signed-off-by:
Jaegeuk Kim <jaegeuk@kernel.org> Signed-off-by:
-
Myungho Jung authored
commit 5fc01fb8 upstream. If cma_acquire_dev_by_src_ip() returns error in addr_handler(), the device state changes back to RDMA_CM_ADDR_BOUND but the resolved source IP address is still left. After that, if rdma_destroy_id() is called after rdma_listen(), the device is freed without removed from listen_any_list in cma_cancel_operation(). Revert to the previous IP address if acquiring device fails. Reported-by: syzbot+f3ce716af730c8f96637@syzkaller.appspotmail.com Signed-off-by:
Myungho Jung <mhjungk@gmail.com> Reviewed-by:
Parav Pandit <parav@mellanox.com> Signed-off-by:
Jason Gunthorpe <jgg@mellanox.com> Signed-off-by:
-
Chris Wilson authored
commit 227ad6d9 upstream. Delay the drm_modeset_acquire_init() until after we check for an allocation failure so that we can return immediately upon error without having to unwind. WARNING: lock held when returning to user space! 4.20.0+ #174 Not tainted ------------------------------------------------ syz-executor556/8153 is leaving the kernel with locks still held! 1 lock held by syz-executor556/8153: #0: 000000005100c85c (crtc_ww_class_acquire){+.+.}, at: set_property_atomic+0xb3/0x330 drivers/gpu/drm/drm_mode_object.c:462 Reported-by: syzbot+6ea337c427f5083ebdf2@syzkaller.appspotmail.com Fixes: 144a7999 ("drm: Handle properties in the core for atomic drivers") Signed-off-by:
Chris Wilson <chris@chris-wilson.co.uk> Cc: Daniel Vetter <daniel.vetter@ffwll.ch> Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com> Cc: Sean Paul <sean@poorly.run> Cc: David Airlie <airlied@linux.ie> Cc: <stable@vger.kernel.org> # v4.14+ Reviewed-by:
Maarten Lankhorst <maarten.lankhorst@linux.intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20181230122842.21917-1-chris@chris-wilson.co.ukSigned-off-by:
-
Kefeng Wang authored
commit 56897b21 upstream. task A: task B: hci_uart_set_proto flush_to_ldisc - p->open(hu) -> h5_open //alloc h5 - receive_buf - set_bit HCI_UART_PROTO_READY - tty_port_default_receive_buf - hci_uart_register_dev - tty_ldisc_receive_buf - hci_uart_tty_receive - test_bit HCI_UART_PROTO_READY - h5_recv - clear_bit HCI_UART_PROTO_READY while() { - p->open(hu) -> h5_close //free h5 - h5_rx_3wire_hdr - h5_reset() //use-after-free } It could use ioctl to set hci uart proto, but there is a use-after-free issue when hci_uart_register_dev() fail in hci_uart_set_proto(), see stack above, fix this by setting HCI_UART_PROTO_READY bit only when hci_uart_register_dev() return success. Reported-by: syzbot+899a33dc0fa0dbaf06a6@syzkaller.appspotmail.com Signed-off-by:
Kefeng Wang <wangkefeng.wang@huawei.com> Reviewed-by:
Jeremy Cline <jcline@redhat.com> Signed-off-by:
-
Jeremy Cline authored
commit 32a7b4cb upstream. The hci_dev struct hdev is referenced in work queues and timers started by open() in some protocols. This creates a race between the initialization function and the work or timer which can result hdev being dereferenced while it is still null. The syzbot report contains a reliable reproducer which causes a null pointer dereference of hdev in hci_uart_write_work() by making the memory allocation for hdev fail. To fix this, ensure hdev is valid from before calling a protocol's open() until after calling a protocol's close(). Reported-by: syzbot+257790c15bcdef6fe00c@syzkaller.appspotmail.com Signed-off-by:
-
Myungho Jung authored
commit e20a2e9c upstream. When releasing socket, it is possible to enter hci_sock_release() and hci_sock_dev_event(HCI_DEV_UNREG) at the same time in different thread. The reference count of hdev should be decremented only once from one of them but if storing hdev to local variable in hci_sock_release() before detached from socket and setting to NULL in hci_sock_dev_event(), hci_dev_put(hdev) is unexpectedly called twice. This is resolved by referencing hdev from socket after bt_sock_unlink() in hci_sock_release(). Reported-by: syzbot+fdc00003f4efff43bc5b@syzkaller.appspotmail.com Signed-off-by:
-
Myungho Jung authored
commit 1dc2d785 upstream. h4_recv_buf() callers store the return value to socket buffer and recursively pass the buffer to h4_recv_buf() without protection. So, ERR_PTR returned from h4_recv_buf() can be dereferenced, if called again before setting the socket buffer to NULL from previous error. Check if skb is ERR_PTR in h4_recv_buf(). Reported-by: syzbot+017a32f149406df32703@syzkaller.appspotmail.com Signed-off-by:
-
Hans Verkuil authored
commit f45f3f75 upstream. Control events can leak kernel memory since they do not fully zero the event. The same code is present in both v4l2-ctrls.c and uvc_ctrl.c, so fix both. It appears that all other event code is properly zeroing the structure, it's these two places. Signed-off-by:
Hans Verkuil <hverkuil-cisco@xs4all.nl> Reported-by: syzbot+4f021cf3697781dbd9fb@syzkaller.appspotmail.com Reviewed-by:
Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by:
Mauro Carvalho Chehab <mchehab+samsung@kernel.org> Signed-off-by:
-
zhangyi (F) authored
commit 674a2b27 upstream. All indirect buffers get by ext4_find_shared() should be released no mater the branch should be freed or not. But now, we forget to release the lower depth indirect buffers when removing space from the same higher depth indirect block. It will lead to buffer leak and futher more, it may lead to quota information corruption when using old quota, consider the following case. - Create and mount an empty ext4 filesystem without extent and quota features, - quotacheck and enable the user & group quota, - Create some files and write some data to them, and then punch hole to some files of them, it may trigger the buffer leak problem mentioned above. - Disable quota and run quotacheck again, it will create two new aquota files and write the checked quota information to them, which probably may reuse the freed indirect block(the buffer and page cache was not freed) as data block. - Enable quota again, it will invoke vfs_load_quota_inode()->invalidate_bdev() to try to clean unused buffers and pagecache. Unfortunately, because of the buffer of quota data block is still referenced, quota code cannot read the up to date quota info from the device and lead to quota information corruption. This problem can be reproduced by xfstests generic/231 on ext3 file system or ext4 file system without extent and quota features. This patch fix this problem by releasing the missing indirect buffers, in ext4_ind_remove_space(). Reported-by:
Hulk Robot <hulkci@huawei.com> Signed-off-by:
zhangyi (F) <yi.zhang@huawei.com> Signed-off-by:
Theodore Ts'o <tytso@mit.edu> Reviewed-by:
-
Lukas Czerner authored
commit 372a03e0 upstream. Ext4 needs to serialize unaligned direct AIO because the zeroing of partial blocks of two competing unaligned AIOs can result in data corruption. However it decides not to serialize if the potentially unaligned aio is past i_size with the rationale that no pending writes are possible past i_size. Unfortunately if the i_size is not block aligned and the second unaligned write lands past i_size, but still into the same block, it has the potential of corrupting the previous unaligned write to the same block. This is (very simplified) reproducer from Frank // 41472 = (10 * 4096) + 512 // 37376 = 41472 - 4096 ftruncate(fd, 41472); io_prep_pwrite(iocbs[0], fd, buf[0], 4096, 37376); io_prep_pwrite(iocbs[1], fd, buf[1], 4096, 41472); io_submit(io_ctx, 1, &iocbs[1]); io_submit(io_ctx, 1, &iocbs[2]); io_getevents(io_ctx, 2, 2, events, NULL); Without this patch the 512B range from 40960 up to the start of the second unaligned write (41472) is going to be zeroed overwriting the data written by the first write. This is a data corruption. 00000000 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 * 00009200 30 30 30 30 30 30 30 30 30 30 30 30 30 30 30 30 * 0000a000 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 * 0000a200 31 31 31 31 31 31 31 31 31 31 31 31 31 31 31 31 With this patch the data corruption is avoided because we will recognize the unaligned_aio and wait for the unwritten extent conversion. 00000000 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 * 00009200 30 30 30 30 30 30 30 30 30 30 30 30 30 30 30 30 * 0000a200 31 31 31 31 31 31 31 31 31 31 31 31 31 31 31 31 * 0000b200 Reported-by:
Frank Sorenson <fsorenso@redhat.com> Signed-off-by:
Lukas Czerner <lczerner@redhat.com> Signed-off-by:
-
Jiufei Xue authored
commit fa30dde3 upstream. We see the following NULL pointer dereference while running xfstests generic/475: BUG: unable to handle kernel NULL pointer dereference at 0000000000000008 PGD 8000000c84bad067 P4D 8000000c84bad067 PUD c84e62067 PMD 0 Oops: 0000 [#1] SMP PTI CPU: 7 PID: 9886 Comm: fsstress Kdump: loaded Not tainted 5.0.0-rc8 #10 RIP: 0010:ext4_do_update_inode+0x4ec/0x760 ... Call Trace: ? jbd2_journal_get_write_access+0x42/0x50 ? __ext4_journal_get_write_access+0x2c/0x70 ? ext4_truncate+0x186/0x3f0 ext4_mark_iloc_dirty+0x61/0x80 ext4_mark_inode_dirty+0x62/0x1b0 ext4_truncate+0x186/0x3f0 ? unmap_mapping_pages+0x56/0x100 ext4_setattr+0x817/0x8b0 notify_change+0x1df/0x430 do_truncate+0x5e/0x90 ? generic_permission+0x12b/0x1a0 This is triggered because the NULL pointer handle->h_transaction was dereferenced in function ext4_update_inode_fsync_trans(). I found that the h_transaction was set to NULL in jbd2__journal_restart but failed to attached to a new transaction while the journal is aborted. Fix this by checking the handle before updating the inode. Fixes: b436b9be ("ext4: Wait for proper transaction commit on fsync") Signed-off-by:
Jiufei Xue <jiufei.xue@linux.alibaba.com> Signed-off-by:
Joseph Qi <joseph.qi@linux.alibaba.com> Cc: stable@kernel.org Signed-off-by:
-
Takashi Iwai authored
commit 31d2350d upstream. ac97_of_get_child_device() take the refcount of the node explicitly via of_node_get(), but this leads to an unbalance. The for_each_child_of_node() loop itself takes the refcount for each iteration node, hence you don't need to take the extra refcount again. Fixes: 2225a3e6 ("ALSA: ac97: add codecs devicetree binding") Reviewed-by:
Robert Jarzmik <robert.jarzmik@free.fr> Signed-off-by:
-
Arnd Bergmann authored
commit 1e73359a upstream. When building without CONFIG_PCI, we can (depending on the architecture) get a link failure: ERROR: "pci_iounmap" [sound/pci/hda/snd-hda-codec-ca0132.ko] undefined! Adding a compile-time check for PCI gets it to work correctly on 32-bit ARM. Fixes: d99501b8 ("ALSA: hda/ca0132 - Call pci_iounmap() instead of iounmap()") Signed-off-by:
Arnd Bergmann <arnd@arndb.de> Signed-off-by:
-
Ville Syrjälä authored
commit 8dfb839c upstream. Commit 46e831ab ("drm/i915/lpe: Mark LPE audio runtime pm as "no callbacks"") broke runtime PM with lpe audio. We can no longer runtime suspend the GPU since the sysfs power/control for the lpe-audio device no longer exists and the device is considered always active. We can fix this by not marking the device as active. Cc: Chris Wilson <chris@chris-wilson.co.uk> Cc: Takashi Iwai <tiwai@suse.de> Cc: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com> Fixes: 46e831ab ("drm/i915/lpe: Mark LPE audio runtime pm as "no callbacks"") Signed-off-by:
Ville Syrjälä <ville.syrjala@linux.intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20181024154825.18185-1-ville.syrjala@linux.intel.comReviewed-by:
-
Steve French authored
commit 8c11a607 upstream. Workaround problem with Samba responses to SMB3.1.1 null user (guest) mounts. The server doesn't set the expected flag in the session setup response so we have to do a similar check to what is done in smb3_validate_negotiate where we also check if the user is a null user (but not sec=krb5 since username might not be passed in on mount for Kerberos case). Note that the commit below tightened the conditions and forced signing for the SMB2-TreeConnect commands as per MS-SMB2. However, this should only apply to normal user sessions and not for cases where there is no user (even if server forgets to set the flag in the response) since we don't have anything useful to sign with. This is especially important now that the more secure SMB3.1.1 protocol is in the default dialect list. An earlier patch ("cifs: allow guest mounts to work for smb3.11") fixed the guest mounts to Windows. Fixes: 6188f28b ("Tree connect for SMB3.1.1 must be signed for non-encrypted shares") Reviewed-by:
Ronnie Sahlberg <lsahlber@redhat.com> Reviewed-by:
Paulo Alcantara <palcantara@suse.de> CC: Stable <stable@vger.kernel.org> Signed-off-by:
Steve French <stfrench@microsoft.com> Signed-off-by:
-
Rasmus Villemoes authored
commit 89dc8917 upstream. The lpi_range_list is supposed to be sorted in ascending order of ->base_id (at least if the range merging is to work), but the current comparison function returns a positive value if rb->base_id > ra->base_id, which means that list_sort() will put A after B in that case - and vice versa, of course. Fixes: 880cb3cd (irqchip/gic-v3-its: Refactor LPI allocator) Cc: stable@vger.kernel.org (v4.19+) Signed-off-by:
Rasmus Villemoes <linux@rasmusvillemoes.dk> Signed-off-by:
Marc Zyngier <marc.zyngier@arm.com> Signed-off-by:
-
Josh Poimboeuf authored
commit 0c671812 upstream. Objtool uses over 512k of stack, thanks to the hash table embedded in the objtool_file struct. This causes an unnecessarily large stack allocation and breaks users with low stack limits. Move the struct off the stack. Fixes: 042ba73f ("objtool: Add several performance improvements") Reported-by:
Vassili Karpov <moosotc@gmail.com> Signed-off-by:
-
Adrian Hunter authored
commit eaeffeb9 upstream. Since commit 4d99e413 ("perf machine: Workaround missing maps for x86 PTI entry trampolines"), perf tools has been creating more than one kernel map, however 'perf probe' assumed there could be only one. Fix by using machine__kernel_map() to get the main kernel map. Signed-off-by:
Adrian Hunter <adrian.hunter@intel.com> Tested-by:
Masami Hiramatsu <mhiramat@kernel.org> Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com> Cc: Andy Lutomirski <luto@kernel.org> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: Jiufei Xue <jiufei.xue@linux.alibaba.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: stable@vger.kernel.org Cc: Xu Yu <xuyu@linux.alibaba.com> Fixes: 4d99e413 ("perf machine: Workaround missing maps for x86 PTI entry trampolines") Fixes: d83212d5 ("kallsyms, x86: Export addresses of PTI entry trampolines") Link: http://lkml.kernel.org/r/2ed432de-e904-85d2-5c36-5897ddc5b23b@intel.comSigned-off-by:
Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by:
-
Ronnie Sahlberg authored
commit e71ab2aa upstream. Fix Guest/Anonymous sessions so that they work with SMB 3.11. The commit noted below tightened the conditions and forced signing for the SMB2-TreeConnect commands as per MS-SMB2. However, this should only apply to normal user sessions and not for Guest/Anonumous sessions. Fixes: 6188f28b ("Tree connect for SMB3.1.1 must be signed for non-encrypted shares") Signed-off-by:
-
Chen Jie authored
commit 5a07168d upstream. The futex code requires that the user space addresses of futexes are 32bit aligned. sys_futex() checks this in futex_get_keys() but the robust list code has no alignment check in place. As a consequence the kernel crashes on architectures with strict alignment requirements in handle_futex_death() when trying to cmpxchg() on an unaligned futex address which was retrieved from the robust list. [ tglx: Rewrote changelog, proper sizeof() based alignement check and add comment ] Fixes: 0771dfef ("[PATCH] lightweight robust futexes: core") Signed-off-by:
Chen Jie <chenjie6@huawei.com> Signed-off-by:
-
Tyrel Datwyler authored
commit 7f5203c1 upstream. The event pool used for queueing commands is destroyed fairly early in the ibmvscsi_remove() code path. Since, this happens prior to the call so scsi_remove_host() it is possible for further calls to queuecommand to be processed which manifest as a panic due to a NULL pointer dereference as seen here: PANIC: "Unable to handle kernel paging request for data at address 0x00000000" Context process backtrace: DSISR: 0000000042000000 ????Syscall Result: 0000000000000000 4 [c000000002cb3820] memcpy_power7 at c000000000064204 [Link Register] [c000000002cb3820] ibmvscsi_send_srp_event at d000000003ed14a4 5 [c000000002cb3920] ibmvscsi_send_srp_event at d000000003ed14a4 [ibmvscsi] ?(unreliable) 6 [c000000002cb39c0] ibmvscsi_queuecommand at d000000003ed2388 [ibmvscsi] 7 [c000000002cb3a70] scsi_dispatch_cmd at d00000000395c2d8 [scsi_mod] 8 [c000000002cb3af0] scsi_request_fn at d00000000395ef88 [scsi_mod] 9 [c000000002cb3be0] __blk_run_queue at c000000000429860 10 [c000000002cb3c10] blk_delay_work at c00000000042a0ec 11 [c000000002cb3c40] process_one_work at c0000000000dac30 12 [c000000002cb3cd0] worker_thread at c0000000000db110 13 [c000000002cb3d80] kthread at c0000000000e3378 14 [c000000002cb3e30] ret_from_kernel_thread at c00000000000982c The kernel buffer log is overfilled with this log: [11261.952732] ibmvscsi: found no event struct in pool! This patch reorders the operations during host teardown. Start by calling the SRP transport and Scsi_Host remove functions to flush any outstanding work and set the host offline. LLDD teardown follows including destruction of the event pool, freeing the Command Response Queue (CRQ), and unmapping any persistent buffers. The event pool destruction is protected by the scsi_host lock, and the pool is purged prior of any requests for which we never received a response. Finally, move the removal of the scsi host from our global list to the end so that the host is easily locatable for debugging purposes during teardown. Cc: <stable@vger.kernel.org> # v2.6.12+ Signed-off-by:
Tyrel Datwyler <tyreld@linux.vnet.ibm.com> Signed-off-by:
Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by:
-
Tyrel Datwyler authored
commit 7205981e upstream. For each ibmvscsi host created during a probe or destroyed during a remove we either add or remove that host to/from the global ibmvscsi_head list. This runs the risk of concurrent modification. This patch adds a simple spinlock around the list modification calls to prevent concurrent updates as is done similarly in the ibmvfc driver and ipr driver. Fixes: 32d6e4b6 ("scsi: ibmvscsi: add vscsi hosts to global list_head") Cc: <stable@vger.kernel.org> # v4.10+ Signed-off-by:
-
Michael Ellerman authored
commit b5b4453e upstream. Jakub Drnec reported: Setting the realtime clock can sometimes make the monotonic clock go back by over a hundred years. Decreasing the realtime clock across the y2k38 threshold is one reliable way to reproduce. Allegedly this can also happen just by running ntpd, I have not managed to reproduce that other than booting with rtc at >2038 and then running ntp. When this happens, anything with timers (e.g. openjdk) breaks rather badly. And included a test case (slightly edited for brevity): #define _POSIX_C_SOURCE 199309L #include <stdio.h> #include <time.h> #include <stdlib.h> #include <unistd.h> long get_time(void) { struct timespec tp; clock_gettime(CLOCK_MONOTONIC, &tp); return tp.tv_sec + tp.tv_nsec / 1000000000; } int main(void) { long last = get_time(); while(1) { long now = get_time(); if (now < last) { printf("clock went backwards by %ld seconds!\n", last - now); } last = now; sleep(1); } return 0; } Which when run concurrently with: # date -s 2040-1-1 # date -s 2037-1-1 Will detect the clock going backward. The root cause is that wtom_clock_sec in struct vdso_data is only a 32-bit signed value, even though we set its value to be equal to tk->wall_to_monotonic.tv_sec which is 64-bits. Because the monotonic clock starts at zero when the system boots the wall_to_montonic.tv_sec offset is negative for current and future dates. Currently on a freshly booted system the offset will be in the vicinity of negative 1.5 billion seconds. However if the wall clock is set past the Y2038 boundary, the offset from wall to monotonic becomes less than negative 2^31, and no longer fits in 32-bits. When that value is assigned to wtom_clock_sec it is truncated and becomes positive, causing the VDSO assembly code to calculate CLOCK_MONOTONIC incorrectly. That causes CLOCK_MONOTONIC to jump ahead by ~4 billion seconds which it is not meant to do. Worse, if the time is then set back before the Y2038 boundary CLOCK_MONOTONIC will jump backward. We can fix it simply by storing the full 64-bit offset in the vdso_data, and using that in the VDSO assembly code. We also shuffle some of the fields in vdso_data to avoid creating a hole. The original commit that added the CLOCK_MONOTONIC support to the VDSO did actually use a 64-bit value for wtom_clock_sec, see commit a7f290da ("[PATCH] powerpc: Merge vdso's and add vdso support to 32 bits kernel") (Nov 2005). However just 3 days later it was converted to 32-bits in commit 0c37ec2a ("[PATCH] powerpc: vdso fixes (take #2)"), and the bug has existed since then AFAICS. Fixes: 0c37ec2a ("[PATCH] powerpc: vdso fixes (take #2)") Cc: stable@vger.kernel.org # v2.6.15+ Link: http://lkml.kernel.org/r/HaC.ZfES.62bwlnvAvMP.1STMMj@seznam.czReported-by:
Jakub Drnec <jaydee@email.cz> Signed-off-by:
Michael Ellerman <mpe@ellerman.id.au> Signed-off-by:
-
Archer Yan authored
commit 47c25036 upstream. Insert Branch instruction instead of NOP to make sure assembler don't patch code in forbidden slot. In jump label function, it might be possible to patch Control Transfer Instructions(CTIs) into forbidden slot, which will generate Reserved Instruction exception in MIPS release 6. Signed-off-by:
Archer Yan <ayan@wavecomp.com> Reviewed-by:
Paul Burton <paul.burton@mips.com> [paul.burton@mips.com: - Add MIPS prefix to subject. - Mark for stable from v4.0, which introduced r6 support, onwards.] Signed-off-by:
-
Yasha Cherikovsky authored
commit 3f0a53bc upstream. This fixes booting with the combination of CONFIG_RELOCATABLE=y and CONFIG_MIPS_ELF_APPENDED_DTB=y. Sections that appear after the relocation table are not relocated on system boot (except .bss, which has special handling). With CONFIG_MIPS_ELF_APPENDED_DTB, the dtb is part of the vmlinux ELF, so it must be relocated together with everything else. Fixes: 069fd766 ("MIPS: Reserve space for relocation table") Signed-off-by:
Yasha Cherikovsky <yasha.che3@gmail.com> Signed-off-by:
-
Yifeng Li authored
commit 5f5f67da upstream. Timekeeping IRQs from CS5536 MFGPT are routed to i8259, which then triggers the "cascade" IRQ on MIPS CPU. Without IRQF_NO_SUSPEND in cascade_irqaction, MFGPT interrupts will be masked in suspend mode, and the machine would be unable to resume once suspended. Previously, MIPS IRQs were not disabled properly, so the original code appeared to work. Commit a3e6c1ef ("MIPS: IRQ: Fix disable_irq on CPU IRQs") uncovers the bug. To fix it, add IRQF_NO_SUSPEND to cascade_irqaction. This commit is functionally identical to 0add9c2f ("MIPS: Loongson-3: Add IRQF_NO_SUSPEND to Cascade irqaction"), but it forgot to apply the same fix to Loongson2. Signed-off-by:
Yifeng Li <tomli@tomli.me> Signed-off-by:
-
Jan Kara authored
commit d3ca4651 upstream. When truncate(2) hits IO error when reading indirect extent block the code just bugs with: kernel BUG at linux-4.15.0/fs/udf/truncate.c:249! ... Fix the problem by bailing out cleanly in case of IO error. CC: stable@vger.kernel.org Reported-by:
jean-luc malet <jeanluc.malet@gmail.com> Signed-off-by:
-
Ilya Dryomov authored
commit bb229bbb upstream. Because map updates are distributed lazily, an OSD may not know about the new blacklist for quite some time after "osd blacklist add" command is completed. This makes it possible for a blacklisted but still alive client to overwrite a post-blacklist update, resulting in data corruption. Waiting for latest osdmap in ceph_monc_blacklist_add() and thus using the post-blacklist epoch for all post-blacklist requests ensures that all such requests "wait" for the blacklist to come into force on their respective OSDs. Cc: stable@vger.kernel.org Fixes: 6305a3b4 ("libceph: support for blacklisting clients") Signed-off-by:
Ilya Dryomov <idryomov@gmail.com> Reviewed-by:
Jason Dillaman <dillaman@redhat.com> Signed-off-by:
-
Stanislaw Gruszka authored
commit 4e50ce03 upstream. Take into account that sg->offset can be bigger than PAGE_SIZE when setting segment sg->dma_address. Otherwise sg->dma_address will point at diffrent page, what makes DMA not possible with erros like this: xhci_hcd 0000:38:00.3: AMD-Vi: Event logged [IO_PAGE_FAULT domain=0x0000 address=0x00000000fdaa70c0 flags=0x0020] xhci_hcd 0000:38:00.3: AMD-Vi: Event logged [IO_PAGE_FAULT domain=0x0000 address=0x00000000fdaa7040 flags=0x0020] xhci_hcd 0000:38:00.3: AMD-Vi: Event logged [IO_PAGE_FAULT domain=0x0000 address=0x00000000fdaa7080 flags=0x0020] xhci_hcd 0000:38:00.3: AMD-Vi: Event logged [IO_PAGE_FAULT domain=0x0000 address=0x00000000fdaa7100 flags=0x0020] xhci_hcd 0000:38:00.3: AMD-Vi: Event logged [IO_PAGE_FAULT domain=0x0000 address=0x00000000fdaa7000 flags=0x0020] Additinally with wrong sg->dma_address unmap_sg will free wrong pages, what what can cause crashes like this: Feb 28 19:27:45 kernel: BUG: Bad page state in process cinnamon pfn:39e8b1 Feb 28 19:27:45 kernel: Disabling lock debugging due to kernel taint Feb 28 19:27:45 kernel: flags: 0x2ffff0000000000() Feb 28 19:27:45 kernel: raw: 02ffff0000000000 0000000000000000 ffffffff00000301 0000000000000000 Feb 28 19:27:45 kernel: raw: 0000000000000000 0000000000000000 00000001ffffffff 0000000000000000 Feb 28 19:27:45 kernel: page dumped because: nonzero _refcount Feb 28 19:27:45 kernel: Modules linked in: ccm fuse arc4 nct6775 hwmon_vid amdgpu nls_iso8859_1 nls_cp437 edac_mce_amd vfat fat kvm_amd ccp rng_core kvm mt76x0u mt76x0_common mt76x02_usb irqbypass mt76_usb mt76x02_lib mt76 crct10dif_pclmul crc32_pclmul chash mac80211 amd_iommu_v2 ghash_clmulni_intel gpu_sched i2c_algo_bit ttm wmi_bmof snd_hda_codec_realtek snd_hda_codec_generic drm_kms_helper snd_hda_codec_hdmi snd_hda_intel drm snd_hda_codec aesni_intel snd_hda_core snd_hwdep aes_x86_64 crypto_simd snd_pcm cfg80211 cryptd mousedev snd_timer glue_helper pcspkr r8169 input_leds realtek agpgart libphy rfkill snd syscopyarea sysfillrect sysimgblt fb_sys_fops soundcore sp5100_tco k10temp i2c_piix4 wmi evdev gpio_amdpt pinctrl_amd mac_hid pcc_cpufreq acpi_cpufreq sg ip_tables x_tables ext4(E) crc32c_generic(E) crc16(E) mbcache(E) jbd2(E) fscrypto(E) sd_mod(E) hid_generic(E) usbhid(E) hid(E) dm_mod(E) serio_raw(E) atkbd(E) libps2(E) crc32c_intel(E) ahci(E) libahci(E) libata(E) xhci_pci(E) xhci_hcd(E) Feb 28 19:27:45 kernel: scsi_mod(E) i8042(E) serio(E) bcache(E) crc64(E) Feb 28 19:27:45 kernel: CPU: 2 PID: 896 Comm: cinnamon Tainted: G B W E 4.20.12-arch1-1-custom #1 Feb 28 19:27:45 kernel: Hardware name: To Be Filled By O.E.M. To Be Filled By O.E.M./B450M Pro4, BIOS P1.20 06/26/2018 Feb 28 19:27:45 kernel: Call Trace: Feb 28 19:27:45 kernel: dump_stack+0x5c/0x80 Feb 28 19:27:45 kernel: bad_page.cold.29+0x7f/0xb2 Feb 28 19:27:45 kernel: __free_pages_ok+0x2c0/0x2d0 Feb 28 19:27:45 kernel: skb_release_data+0x96/0x180 Feb 28 19:27:45 kernel: __kfree_skb+0xe/0x20 Feb 28 19:27:45 kernel: tcp_recvmsg+0x894/0xc60 Feb 28 19:27:45 kernel: ? reuse_swap_page+0x120/0x340 Feb 28 19:27:45 kernel: ? ptep_set_access_flags+0x23/0x30 Feb 28 19:27:45 kernel: inet_recvmsg+0x5b/0x100 Feb 28 19:27:45 kernel: __sys_recvfrom+0xc3/0x180 Feb 28 19:27:45 kernel: ? handle_mm_fault+0x10a/0x250 Feb 28 19:27:45 kernel: ? syscall_trace_enter+0x1d3/0x2d0 Feb 28 19:27:45 kernel: ? __audit_syscall_exit+0x22a/0x290 Feb 28 19:27:45 kernel: __x64_sys_recvfrom+0x24/0x30 Feb 28 19:27:45 kernel: do_syscall_64+0x5b/0x170 Feb 28 19:27:45 kernel: entry_SYSCALL_64_after_hwframe+0x44/0xa9 Cc: stable@vger.kernel.org Reported-and-tested-by:
Jan Viktorin <jan.viktorin@gmail.com> Reviewed-by:
Alexander Duyck <alexander.h.duyck@linux.intel.com> Signed-off-by:
Stanislaw Gruszka <sgruszka@redhat.com> Fixes: 80187fd3 ('iommu/amd: Optimize map_sg and unmap_sg') Signed-off-by:
Joerg Roedel <jroedel@suse.de> Signed-off-by:
-
