This integrates the PHY wrapper into the core hcd infrastructure.
Multiple PHYs which are part of the HCD's device tree node are now
managed (= powered on/off when needed), by the new usb_phy_roothub code.

Suspend and resume is also supported, however not for
runtime/auto-suspend (which is triggered for example when no devices are
connected to the USB bus). This is needed on some SoCs (for example
Amlogic Meson GXL) because if the PHYs are disabled during auto-suspend
then devices which are plugged in afterwards are not seen by the host.

One example where this is required is the Amlogic GXL and GXM SoCs:
They are using a dwc3 USB controller with up to three ports enabled on
the internal roothub. Each port has it's own PHY which must be enabled
(if one of the PHYs is left disabled then none of the USB ports works at
all).
The new logic works on the Amlogic GXL and GXM SoCs because the dwc3
driver internally creates a xhci-hcd which then registers a HCD which
then triggers our new PHY wrapper.

USB controller drivers can opt out of this by setting
"skip_phy_initialization" in struct usb_hcd to true. This is identical
to how it works for a single USB PHY, so the "multiple PHY" handling is
disabled for drivers that opted out of the management logic of a single
PHY.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Tested-by: Yixun Lan <yixun.lan@amlogic.com>
Tested-by: Neil Armstrong <narmstrong@baylibre.con>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Many SoC platforms have separate devices for the USB PHY which are
registered through the generic PHY framework. These PHYs have to be
enabled to make the USB controller actually work. They also have to be
disabled again on shutdown/suspend.

Currently (at least) the following HCI platform drivers are using custom
code to obtain all PHYs via devicetree for the roothub/controller and
disable/enable them when required:
- ehci-platform.c has ehci_platform_power_{on,off}
- xhci-mtk.c has xhci_mtk_phy_{init,exit,power_on,power_off}
- ohci-platform.c has ohci_platform_power_{on,off}

With this new wrapper the USB PHYs can be specified directly in the
USB controller's devicetree node (just like on the drivers listed
above). This allows SoCs like the Amlogic Meson GXL family to operate
correctly once this is wired up correctly. These SoCs use a dwc3
controller and require all USB PHYs to be initialized (if one of the USB
PHYs it not initialized then none of USB port works at all).
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Tested-by: Yixun Lan <yixun.lan@amlogic.com>
Cc: Chunfeng Yun <chunfeng.yun@mediatek.com>
Tested-by: Neil Armstrong <narmstrong@baylibre.con>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The USB HCD core driver parses the device-tree node for "phys" and
"usb-phys" properties. It also manages the power state of these PHYs
automatically.
However, drivers may opt-out of this behavior by setting "phy" or
"usb_phy" in struct usb_hcd to a non-null value. An example where this
is required is the "Qualcomm USB2 controller", implemented by the
chipidea driver. The hardware requires that the PHY is only powered on
after the "reset completed" event from the controller is received.

A follow-up patch will allow the USB HCD core driver to manage more than
one PHY. Add a new "skip_phy_initialization" bitflag to struct usb_hcd
so drivers can opt-out of any PHY management provided by the USB HCD
core driver.

This also updates the existing drivers so they use the new flag if they
want to opt out of the PHY management provided by the USB HCD core
driver. This means that for these drivers the new "multiple PHY"
handling (which will be added in a follow-up patch) will be disabled as
well.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Acked-by: Peter Chen <peter.chen@nxp.com>
Tested-by: Neil Armstrong <narmstrong@baylibre.con>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

A USB HCD may have several PHYs which need to be configured before the
the HCD starts working.
This adds the documentation for such a USB HCD as well as a reference to
the new "usb-hcd.txt" from all bindings that implement a USB HCD which
support one USB PHY per port.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Tested-by: Yixun Lan <yixun.lan@amlogic.com>
Tested-by: Neil Armstrong <narmstrong@baylibre.con>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Use kasprintf instead of combination of kmalloc and sprintf and
therefore avoid unnecessary computation of string length.
Also, remove the useless local variable.
Signed-off-by: Himanshu Jha <himanshujha199640@gmail.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ACPI spec inserts sections for new features frequently and section
numbers are changed. It is easy to refer to ACPI spec if ACPI version
is available in comments.

There are no functional changes.
Signed-off-by: Alex Hung <alex.hung@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Disabing Latency Tolerance Messaging before port reset is unnecessary.
LTM is automatically disabled at port reset.

If host can't communicate with the device the LTM message will fail, and
the hub driver will unnecessarily do a logical disconnect.
Broken communication is ofter the reason for a reset in the first place.

Additionally we can't guarantee device is in a configured state,
epecially in reset-resume case when root hub lost power.
LTM can't be modified unless device is in a configured state.

Just remove LTM disabling before port reset.

Details about LTM and port reset in USB 3 specification:

USB 3 spec section 9.4.5
"The LTM Enable field can be modified by the SetFeature() and
ClearFeature() requests using the LTM_ENABLE feature selector.
This field is reset to zero when the device is reset."

USB 3 spec section 9.4.1
"The device shall process a Clear Feature (U1_Enable or U2_Enable or
LTM_Enable) only if the device is in the configured state."
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Add waiting for an URB transmit finish that let the last URB to be sent
(to be not discarded) during 'release' procedure. W/o this waiting,the
last frame will be nearly always lost.

A test case: an attempt of sending a single frame:
echo -en "\001mk255" >/dev/adutux0
Signed-off-by: Kirill Kapranov <kirill.kirillovich.kapranov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

...instead of open coding file operations followed by custom ->open()
callbacks per each attribute.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

...instead of open coding file operations followed by custom ->open()
callbacks per each attribute.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

...instead of open coding file operations followed by custom ->open()
callbacks per each attribute.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

...instead of open coding file operations followed by custom ->open()
callbacks per each attribute.

Cc: Olav Kongas <ok@artecdesign.ee>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

...instead of open coding file operations followed by custom ->open()
callbacks per each attribute.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

...instead of open coding file operations followed by custom ->open()
callbacks per each attribute.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

...instead of open coding file operations followed by custom ->open()
callbacks per each attribute.

Cc: Daniel Mack <daniel@zonque.org>
Cc: Haojian Zhuang <haojian.zhuang@gmail.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

...instead of open coding file operations followed by custom ->open()
callbacks per each attribute.

Cc: Daniel Mack <daniel@zonque.org>
Cc: Haojian Zhuang <haojian.zhuang@gmail.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

...instead of open coding file operations followed by custom ->open()
callbacks per each attribute.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

...instead of open coding file operations followed by custom ->open()
callbacks per each attribute.

Cc: Kevin Cernekee <cernekee@gmail.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: bcm-kernel-feedback-list@broadcom.com
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

...instead of open coding file operations followed by custom ->open()
callbacks per each attribute.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

...instead of open coding file operations followed by custom ->open()
callbacks per each attribute.

Cc: John Youn <johnyoun@synopsys.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

...instead of open coding file operations followed by custom ->open()
callbacks per each attribute.

Cc: Peter Chen <Peter.Chen@nxp.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This commit adds a header providing definitions for handling
Status messages. Currently the header only focuses on handling
incoming Status messages.
Signed-off-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This commit adds a header providing definitions for handling Alert
messages. Currently the header only focuses on handling incoming
alerts.
Signed-off-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This commit adds definitions for PD Rev 3.0 messages, including
APDO PPS and extended message support for TCPM.
Signed-off-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Changed usbip_network, usbip_attach, usbip_list, and usbipd to use
and propagate the new error codes in server reply messages.

usbip_net_recv_op_common() is changed to take a pointer to status
return the status returned in the op_common.status to callers.

usbip_attach and usbip_list use the common interface to print error
messages to indicate why the request failed.

With this change the messages say why a request failed:

- when a client requests a device that is already exported:

usbip attach -r server_name -b 3-10.2
usbip: error: Attach Request for 3-10.2 failed - Device busy (exported)

- when a client requests a device that isn't exportable,

usbip attach -r server_name -b 3-10.4
usbip: error: Attach Request for 3-10.4 failed - Device not found
Signed-off-by: Shuah Khan <shuahkh@osg.samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Currently ST_OK and ST_NA are the only values used to communicate
status of a request from a client. Use new error codes to clearly
indicate what failed. For example, when client sends request to
import a device that isn't export-able, send ST_DEV_BUSY to the client.
Signed-off-by: Shuah Khan <shuahkh@osg.samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Currently ST_OK and ST_NA are the only values defined to communicate
status of a request from a client. Add more error codes to clearly
indicate what failed. For example, when client sends request to import
a device that isn't export-able, server can send a specific error code
to the client.

Existing defines are moved to a common header in libsrc to be included
in the libusbip_la-usbip_common.o to be used by all the usbip tools.
Supporting interface to print error strings is added to the common lib.
Signed-off-by: Shuah Khan <shuahkh@osg.samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Kernel and tool version mismatch message is cryptic. Fix it to be
informative.
Signed-off-by: Shuah Khan <shuahkh@osg.samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Attach device error message is cryptic and useless. Fix it to be
informative.
Signed-off-by: Shuah Khan <shuahkh@osg.samsung.com>
Reviewed-by: Krzysztof Opasiak <k.opasiak@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Pointer dev is initialized and then re-assigned with the same value
a little later, hence the second assignment is redundant and can be
removed.

Cleans up clang warning:
drivers/usb/wusbcore/wa-nep.c:88:17: warning: Value stored to 'dev'
during its initialization is never read
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Now that usbip supports USB3, the maximum number of ports allowed
on a hub is 15 (USB_SS_MAXPORTS), not 31 (USB_MAXCHILDREN).
Reported-by: Gianluigi Tiesi <sherpya@netfarm.it>
Reported-by: Borissh1983 <borissh1983@gmail.com>
References: https://bugs.debian.org/878866
Fixes: 1c9de5bf ("usbip: vhci-hcd: Add USB3 SuperSpeed support")
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The kernel would like to have all stack VLA usage removed[1].  We
already have a pre-processor constant defined MAX_SGLEN.  We can use
this instead of the variable param-sglen.

[1]: https://lkml.org/lkml/2018/3/7/621Signed-off-by: Tobin C. Harding <me@tobin.cc>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Delete a misleading comment to an obvious definition.
Signed-off-by: Kirill Kapranov <kirill.kirillovich.kapranov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

GPL v2 is the original license according to the old license text.
See f64cdd0e.
Signed-off-by: Marcus Folkesson <marcus.folkesson@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

We want the USB fixes in here.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Pull Xtensa fixes from Max Filippov:
 "Two fixes for reserved memory/DMA buffers allocation in high memory on
  xtensa architecture

   - fix memory accounting when reserved memory is in high memory region

   - fix DMA allocation from high memory"

* tag 'xtensa-20180225' of git://github.com/jcmvbkbc/linux-xtensa:
  xtensa: support DMA buffers in high memory
  xtensa: fix high memory/reserved memory collision

Pull x86 fixes from Thomas Gleixner:
 "A small set of fixes:

   - UAPI data type correction for hyperv

   - correct the cpu cores field in /proc/cpuinfo on CPU hotplug

   - return proper error code in the resctrl file system failure path to
     avoid silent subsequent failures

   - correct a subtle accounting issue in the new vector allocation code
     which went unnoticed for a while and caused suspend/resume
     failures"

* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/topology: Update the 'cpu cores' field in /proc/cpuinfo correctly across CPU hotplug operations
  x86/topology: Fix function name in documentation
  x86/intel_rdt: Fix incorrect returned value when creating rdgroup sub-directory in resctrl file system
  x86/apic/vector: Handle vector release on CPU unplug correctly
  genirq/matrix: Handle CPU offlining proper
  x86/headers/UAPI: Use __u64 instead of u64 in <uapi/asm/hyperv.h>

Pull perf fix from Thomas Gleixner:
 "A single commit which shuts up a bogus GCC-8 warning"

* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/oprofile: Fix bogus GCC-8 warning in nmi_setup()

Pull locking fixes from Thomas Gleixner:
 "Three patches to fix memory ordering issues on ALPHA and a comment to
  clarify the usage scope of a mutex internal function"

* 'locking-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  locking/xchg/alpha: Fix xchg() and cmpxchg() memory ordering bugs
  locking/xchg/alpha: Clean up barrier usage by using smp_mb() in place of __ASM__MB
  locking/xchg/alpha: Add unconditional memory barrier to cmpxchg()
  locking/mutex: Add comment to __mutex_owner() to deter usage