Pull networking fixes from Jakub Kicinski:
 "Networking fixes, including fixes from mac80211, wifi, bpf.

  Relatively large batches of fixes from BPF and the WiFi stack, calm in
  general networking.

  Current release - regressions:

   - dpaa2-eth: fix buffer overrun when reporting ethtool statistics

  Current release - new code bugs:

   - bpf: fix incorrect state pruning for <8B spill/fill

   - iavf:
       - add missing unlocks in iavf_watchdog_task()
       - do not override the adapter state in the watchdog task (again)

   - mlxsw: spectrum_router: consolidate MAC profiles when possible

  Previous releases - regressions:

   - mac80211 fixes:
       - rate control, avoid driver crash for retransmitted frames
       - regression in SSN handling of addba tx
       - a memory leak where sta_info is not freed
       - marking TX-during-stop for TX in in_reconfig, prevent stall

   - cfg80211: acquire wiphy mutex on regulatory work

   - wifi drivers: fix build regressions and LED config dependency

   - virtio_net: fix rx_drops stat for small pkts

   - dsa: mv88e6xxx: unforce speed & duplex in mac_link_down()

  Previous releases - always broken:

   - bpf fixes:
       - kernel address leakage in atomic fetch
       - kernel address leakage in atomic cmpxchg's r0 aux reg
       - signed bounds propagation after mov32
       - extable fixup offset
       - extable address check

   - mac80211:
       - fix the size used for building probe request
       - send ADDBA requests using the tid/queue of the aggregation
         session
       - agg-tx: don't schedule_and_wake_txq() under sta->lock, avoid
         deadlocks
       - validate extended element ID is present

   - mptcp:
       - never allow the PM to close a listener subflow (null-defer)
       - clear 'kern' flag from fallback sockets, prevent crash
       - fix deadlock in __mptcp_push_pending()

   - inet_diag: fix kernel-infoleak for UDP sockets

   - xsk: do not sleep in poll() when need_wakeup set

   - smc: avoid very long waits in smc_release()

   - sch_ets: don't remove idle classes from the round-robin list

   - netdevsim:
       - zero-initialize memory for bpf map's value, prevent info leak
       - don't let user space overwrite read only (max) ethtool parms

   - ixgbe: set X550 MDIO speed before talking to PHY

   - stmmac:
       - fix null-deref in flower deletion w/ VLAN prio Rx steering
       - dwmac-rk: fix oob read in rk_gmac_setup

   - ice: time stamping fixes

   - systemport: add global locking for descriptor life cycle"

* tag 'net-5.16-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (89 commits)
  bpf, selftests: Fix racing issue in btf_skc_cls_ingress test
  selftest/bpf: Add a test that reads various addresses.
  bpf: Fix extable address check.
  bpf: Fix extable fixup offset.
  bpf, selftests: Add test case trying to taint map value pointer
  bpf: Make 32->64 bounds propagation slightly more robust
  bpf: Fix signed bounds propagation after mov32
  sit: do not call ipip6_dev_free() from sit_init_net()
  net: systemport: Add global locking for descriptor lifecycle
  net/smc: Prevent smc_release() from long blocking
  net: Fix double 0x prefix print in SKB dump
  virtio_net: fix rx_drops stat for small pkts
  dsa: mv88e6xxx: fix debug print for SPEED_UNFORCED
  sfc_ef100: potential dereference of null pointer
  net: stmmac: dwmac-rk: fix oob read in rk_gmac_setup
  net: usb: lan78xx: add Allied Telesis AT29M2-AF
  net/packet: rx_owner_map depends on pg_vec
  netdevsim: Zero-initialize memory for new map's value in function nsim_bpf_map_alloc
  dpaa2-eth: fix ethtool statistics
  ixgbe: set X550 MDIO speed before talking to PHY
  ...

Pull ARM SoC fixes from Arnd Bergmann:
 "There are a number of DT fixes, mostly for mistakes found through
  static checking of the dts files again, as well as a couple of minor
  changes to address incorrect DT settings.

  For i.MX, there is yet another series of devitree changes to update
  RGMII delay settings for ethernet, which is an ongoing problem after
  some driver changes.

  For SoC specific device drivers, a number of smaller fixes came up:

   - i.MX SoC identification was incorrectly registered non-i.MX
     machines when the driver is built-in

   - One fix on imx8m-blk-ctrl driver to get i.MX8MM MIPI reset work
     properly

   - a few compile fixes for warnings that get in the way of -Werror

   - a string overflow in the scpi firmware driver

   - a boot failure with FORTIFY_SOURCE on Rockchips machines

   - broken error handling in the AMD TEE driver

   - a revert for a tegra reset driver commit that broke HDA"

* tag 'soc-fixes-5.16-3' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (25 commits)
  soc/tegra: fuse: Fix bitwise vs. logical OR warning
  firmware: arm_scpi: Fix string overflow in SCPI genpd driver
  soc: imx: Register SoC device only on i.MX boards
  soc: imx: imx8m-blk-ctrl: Fix imx8mm mipi reset
  ARM: dts: imx6ull-pinfunc: Fix CSI_DATA07__ESAI_TX0 pad name
  arm64: dts: imx8mq: remove interconnect property from lcdif
  ARM: socfpga: dts: fix qspi node compatible
  arm64: dts: apple: add #interrupt-cells property to pinctrl nodes
  dt-bindings: i2c: apple,i2c: allow multiple compatibles
  arm64: meson: remove COMMON_CLK
  arm64: meson: fix dts for JetHub D1
  tee: amdtee: fix an IS_ERR() vs NULL bug
  arm64: dts: apple: change ethernet0 device type to ethernet
  arm64: dts: ten64: remove redundant interrupt declaration for gpio-keys
  arm64: dts: rockchip: fix poweroff on helios64
  arm64: dts: rockchip: fix audio-supply for Rock Pi 4
  arm64: dts: rockchip: fix rk3399-leez-p710 vcc3v3-lan supply
  arm64: dts: rockchip: fix rk3308-roc-cc vcc-sd supply
  arm64: dts: rockchip: remove mmc-hs400-enhanced-strobe from rk3399-khadas-edge
  ARM: rockchip: Use memcpy_toio instead of memcpy on smp bring-up
  ...

Daniel Borkmann says:

====================
pull-request: bpf 2021-12-16

We've added 15 non-merge commits during the last 7 day(s) which contain
a total of 12 files changed, 434 insertions(+), 30 deletions(-).

The main changes are:

1) Fix incorrect verifier state pruning behavior for <8B register spill/fill,
   from Paul Chaignon.

2) Fix x86-64 JIT's extable handling for fentry/fexit when return pointer
   is an ERR_PTR(), from Alexei Starovoitov.

3) Fix 3 different possibilities that BPF verifier missed where unprivileged
   could leak kernel addresses, from Daniel Borkmann.

4) Fix xsk's poll behavior under need_wakeup flag, from Magnus Karlsson.

5) Fix an oob-write in test_verifier due to a missed MAX_NR_MAPS bump,
   from Kumar Kartikeya Dwivedi.

6) Fix a race in test_btf_skc_cls_ingress selftest, from Martin KaFai Lau.

* https://git.kernel.org/pub/scm/linux/kernel/git/bpf/bpf:
  bpf, selftests: Fix racing issue in btf_skc_cls_ingress test
  selftest/bpf: Add a test that reads various addresses.
  bpf: Fix extable address check.
  bpf: Fix extable fixup offset.
  bpf, selftests: Add test case trying to taint map value pointer
  bpf: Make 32->64 bounds propagation slightly more robust
  bpf: Fix signed bounds propagation after mov32
  bpf, selftests: Update test case for atomic cmpxchg on r0 with pointer
  bpf: Fix kernel address leakage in atomic cmpxchg's r0 aux reg
  bpf, selftests: Add test case for atomic fetch on spilled pointer
  bpf: Fix kernel address leakage in atomic fetch
  selftests/bpf: Fix OOB write in test_verifier
  xsk: Do not sleep in poll() when need_wakeup set
  selftests/bpf: Tests for state pruning with u32 spill/fill
  bpf: Fix incorrect state pruning for <8B spill/fill
====================

Link: https://lore.kernel.org/r/20211216210005.13815-1-daniel@iogearbox.netSigned-off-by: Jakub Kicinski <kuba@kernel.org>

The libbpf CI reported occasional failure in btf_skc_cls_ingress:

  test_syncookie:FAIL:Unexpected syncookie states gen_cookie:80326634 recv_cookie:0
  bpf prog error at line 97

"error at line 97" means the bpf prog cannot find the listening socket
when the final ack is received.  It then skipped processing
the syncookie in the final ack which then led to "recv_cookie:0".

The problem is the userspace program did not do accept() and went
ahead to close(listen_fd) before the kernel (and the bpf prog) had
a chance to process the final ack.

The fix is to add accept() call so that the userspace will wait for
the kernel to finish processing the final ack first before close()-ing
everything.

Fixes: 9a856cae ("bpf: selftest: Add test_btf_skc_cls_ingress")
Reported-by: Andrii Nakryiko <andrii@kernel.org>
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Link: https://lore.kernel.org/bpf/20211216191630.466151-1-kafai@fb.com

Add a function to bpf_testmod that returns invalid kernel and user addresses.
Then attach an fexit program to that function that tries to read
memory through these addresses.

This logic checks that bpf_probe_read_kernel and BPF_PROBE_MEM logic is sane.
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>

The verifier checks that PTR_TO_BTF_ID pointer is either valid or NULL,
but it cannot distinguish IS_ERR pointer from valid one.

When offset is added to IS_ERR pointer it may become small positive
value which is a user address that is not handled by extable logic
and has to be checked for at the runtime.

Tighten BPF_PROBE_MEM pointer check code to prevent this case.

Fixes: 4c5de127 ("bpf: Emit explicit NULL pointer checks for PROBE_LDX instructions.")
Reported-by: Lorenzo Fontana <lorenzo.fontana@elastic.co>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>

The prog - start_of_ldx is the offset before the faulting ldx to the location
after it, so this will be used to adjust pt_regs->ip for jumping over it and
continuing, and with old temp it would have been fixed up to the wrong offset,
causing crash.

Fixes: 4c5de127 ("bpf: Emit explicit NULL pointer checks for PROBE_LDX instructions.")
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Reviewed-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>

Pull clk fix from Stephen Boyd:
 "A single fix for the clk framework that needed some more bake time in
  linux-next.

  The problem is that two clks being registered at the same time can
  lead to a busted clk tree if the parent isn't fully registered by the
  time the child finds the parent. We rejigger the place where we mark
  the parent as fully registered so that the child can't find the parent
  until things are proper"

* tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux:
  clk: Don't parent clks until the parent is fully registered

Add a test case which tries to taint map value pointer arithmetic into a
unknown scalar with subsequent export through the map.

Before fix:

  # ./test_verifier 1186
  #1186/u map access: trying to leak tained dst reg FAIL
  Unexpected success to load!
  verification time 24 usec
  stack depth 8
  processed 15 insns (limit 1000000) max_states_per_insn 0 total_states 1 peak_states 1 mark_read 1
  #1186/p map access: trying to leak tained dst reg FAIL
  Unexpected success to load!
  verification time 8 usec
  stack depth 8
  processed 15 insns (limit 1000000) max_states_per_insn 0 total_states 1 peak_states 1 mark_read 1
  Summary: 0 PASSED, 0 SKIPPED, 2 FAILED

After fix:

  # ./test_verifier 1186
  #1186/u map access: trying to leak tained dst reg OK
  #1186/p map access: trying to leak tained dst reg OK
  Summary: 2 PASSED, 0 SKIPPED, 0 FAILED
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Reviewed-by: John Fastabend <john.fastabend@gmail.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>

Make the bounds propagation in __reg_assign_32_into_64() slightly more
robust and readable by aligning it similarly as we did back in the
__reg_combine_64_into_32() counterpart. Meaning, only propagate or
pessimize them as a smin/smax pair.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Reviewed-by: John Fastabend <john.fastabend@gmail.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>

For the case where both s32_{min,max}_value bounds are positive, the
__reg_assign_32_into_64() directly propagates them to their 64 bit
counterparts, otherwise it pessimises them into [0,u32_max] universe and
tries to refine them later on by learning through the tnum as per comment
in mentioned function. However, that does not always happen, for example,
in mov32 operation we call zext_32_to_64(dst_reg) which invokes the
__reg_assign_32_into_64() as is without subsequent bounds update as
elsewhere thus no refinement based on tnum takes place.

Thus, not calling into the __update_reg_bounds() / __reg_deduce_bounds() /
__reg_bound_offset() triplet as we do, for example, in case of ALU ops via
adjust_scalar_min_max_vals(), will lead to more pessimistic bounds when
dumping the full register state:

Before fix:

  0: (b4) w0 = -1
  1: R0_w=invP4294967295
     (id=0,imm=ffffffff,
      smin_value=4294967295,smax_value=4294967295,
      umin_value=4294967295,umax_value=4294967295,
      var_off=(0xffffffff; 0x0),
      s32_min_value=-1,s32_max_value=-1,
      u32_min_value=-1,u32_max_value=-1)

  1: (bc) w0 = w0
  2: R0_w=invP4294967295
     (id=0,imm=ffffffff,
      smin_value=0,smax_value=4294967295,
      umin_value=4294967295,umax_value=4294967295,
      var_off=(0xffffffff; 0x0),
      s32_min_value=-1,s32_max_value=-1,
      u32_min_value=-1,u32_max_value=-1)

Technically, the smin_value=0 and smax_value=4294967295 bounds are not
incorrect, but given the register is still a constant, they break assumptions
about const scalars that smin_value == smax_value and umin_value == umax_value.

After fix:

  0: (b4) w0 = -1
  1: R0_w=invP4294967295
     (id=0,imm=ffffffff,
      smin_value=4294967295,smax_value=4294967295,
      umin_value=4294967295,umax_value=4294967295,
      var_off=(0xffffffff; 0x0),
      s32_min_value=-1,s32_max_value=-1,
      u32_min_value=-1,u32_max_value=-1)

  1: (bc) w0 = w0
  2: R0_w=invP4294967295
     (id=0,imm=ffffffff,
      smin_value=4294967295,smax_value=4294967295,
      umin_value=4294967295,umax_value=4294967295,
      var_off=(0xffffffff; 0x0),
      s32_min_value=-1,s32_max_value=-1,
      u32_min_value=-1,u32_max_value=-1)

Without the smin_value == smax_value and umin_value == umax_value invariant
being intact for const scalars, it is possible to leak out kernel pointers
from unprivileged user space if the latter is enabled. For example, when such
registers are involved in pointer arithmtics, then adjust_ptr_min_max_vals()
will taint the destination register into an unknown scalar, and the latter
can be exported and stored e.g. into a BPF map value.

Fixes: 3f50f132 ("bpf: Verifier, do explicit ALU32 bounds tracking")
Reported-by: Kuee K1r0a <liulin063@gmail.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Reviewed-by: John Fastabend <john.fastabend@gmail.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>

Pull arm64 fix from Catalin Marinas:
 "Fix missing error code on kexec failure path"

* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
  arm64: kexec: Fix missing error code 'ret' warning in load_other_segments()

Merge tag 'for-5.16/dm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm

Pull device mapper fixes from Mike Snitzer:

 - Fix use after free in DM btree remove's rebalance_children()

 - Fix DM integrity data corruption, introduced during 5.16 merge, due
   to improper use of bvec_kmap_local()

* tag 'for-5.16/dm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm:
  dm integrity: fix data corruption due to improper use of bvec_kmap_local
  dm btree remove: fix use after free in rebalance_children()

Since commit ac10be5c ("arm64: Use common
of_kexec_alloc_and_setup_fdt()"), smatch reports the following warning:

  arch/arm64/kernel/machine_kexec_file.c:152 load_other_segments()
  warn: missing error code 'ret'

Return code is not set to an error code in load_other_segments() when
of_kexec_alloc_and_setup_fdt() call returns a NULL dtb. This results
in status success (return code set to 0) being returned from
load_other_segments().

Set return code to -EINVAL if of_kexec_alloc_and_setup_fdt() returns
NULL dtb.
Signed-off-by: Lakshmi Ramasubramanian <nramas@linux.microsoft.com>
Reported-by: kernel test robot <lkp@intel.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Fixes: ac10be5c ("arm64: Use common of_kexec_alloc_and_setup_fdt()")
Link: https://lore.kernel.org/r/20211210010121.101823-1-nramas@linux.microsoft.comSigned-off-by: Will Deacon <will@kernel.org>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>

Fix afs_add_open_map() to check that the vnode isn't already on the list
when it adds it.  It's possible that afs_drop_open_mmap() decremented
the cb_nr_mmap counter, but hadn't yet got into the locked section to
remove it.

Also vnode->cb_mmap_link should be initialised, so fix that too.

Fixes: 6e0e99d5 ("afs: Fix mmap coherency vs 3rd-party changes")
Reported-by: kafs-testing+fedora34_64checkkafs-build-300@auristor.com
Suggested-by: Marc Dionne <marc.dionne@auristor.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Tested-by: kafs-testing+fedora34_64checkkafs-build-300@auristor.com
cc: linux-afs@lists.infradead.org
Link: https://lore.kernel.org/r/686465.1639435380@warthog.procyon.org.uk/ # v1
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

ipip6_dev_free is sit dev->priv_destructor, already called
by register_netdevice() if something goes wrong.

Alternative would be to make ipip6_dev_free() robust against
multiple invocations, but other drivers do not implement this
strategy.

syzbot reported:

dst_release underflow
WARNING: CPU: 0 PID: 5059 at net/core/dst.c:173 dst_release+0xd8/0xe0 net/core/dst.c:173
Modules linked in:
CPU: 1 PID: 5059 Comm: syz-executor.4 Not tainted 5.16.0-rc5-syzkaller #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
RIP: 0010:dst_release+0xd8/0xe0 net/core/dst.c:173
Code: 4c 89 f2 89 d9 31 c0 5b 41 5e 5d e9 da d5 44 f9 e8 1d 90 5f f9 c6 05 87 48 c6 05 01 48 c7 c7 80 44 99 8b 31 c0 e8 e8 67 29 f9 <0f> 0b eb 85 0f 1f 40 00 53 48 89 fb e8 f7 8f 5f f9 48 83 c3 a8 48
RSP: 0018:ffffc9000aa5faa0 EFLAGS: 00010246
RAX: d6894a925dd15a00 RBX: 00000000ffffffff RCX: 0000000000040000
RDX: ffffc90005e19000 RSI: 000000000003ffff RDI: 0000000000040000
RBP: 0000000000000000 R08: ffffffff816a1f42 R09: ffffed1017344f2c
R10: ffffed1017344f2c R11: 0000000000000000 R12: 0000607f462b1358
R13: 1ffffffff1bfd305 R14: ffffe8ffffcb1358 R15: dffffc0000000000
FS:  00007f66c71a2700(0000) GS:ffff8880b9a00000(0000) knlGS:0000000000000000
CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00007f88aaed5058 CR3: 0000000023e0f000 CR4: 00000000003506f0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
Call Trace:
 <TASK>
 dst_cache_destroy+0x107/0x1e0 net/core/dst_cache.c:160
 ipip6_dev_free net/ipv6/sit.c:1414 [inline]
 sit_init_net+0x229/0x550 net/ipv6/sit.c:1936
 ops_init+0x313/0x430 net/core/net_namespace.c:140
 setup_net+0x35b/0x9d0 net/core/net_namespace.c:326
 copy_net_ns+0x359/0x5c0 net/core/net_namespace.c:470
 create_new_namespaces+0x4ce/0xa00 kernel/nsproxy.c:110
 unshare_nsproxy_namespaces+0x11e/0x180 kernel/nsproxy.c:226
 ksys_unshare+0x57d/0xb50 kernel/fork.c:3075
 __do_sys_unshare kernel/fork.c:3146 [inline]
 __se_sys_unshare kernel/fork.c:3144 [inline]
 __x64_sys_unshare+0x34/0x40 kernel/fork.c:3144
 do_syscall_x64 arch/x86/entry/common.c:50 [inline]
 do_syscall_64+0x44/0xd0 arch/x86/entry/common.c:80
 entry_SYSCALL_64_after_hwframe+0x44/0xae
RIP: 0033:0x7f66c882ce99
Code: ff ff c3 66 2e 0f 1f 84 00 00 00 00 00 0f 1f 40 00 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff ff 73 01 c3 48 c7 c1 bc ff ff ff f7 d8 64 89 01 48
RSP: 002b:00007f66c71a2168 EFLAGS: 00000246 ORIG_RAX: 0000000000000110
RAX: ffffffffffffffda RBX: 00007f66c893ff60 RCX: 00007f66c882ce99
RDX: 0000000000000000 RSI: 0000000000000000 RDI: 0000000048040200
RBP: 00007f66c8886ff1 R08: 0000000000000000 R09: 0000000000000000
R10: 0000000000000000 R11: 0000000000000246 R12: 0000000000000000
R13: 00007fff6634832f R14: 00007f66c71a2300 R15: 0000000000022000
 </TASK>

Fixes: cf124db5 ("net: Fix inconsistent teardown and release of private netdev state.")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Link: https://lore.kernel.org/r/20211216111741.1387540-1-eric.dumazet@gmail.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

The descriptor list is a shared resource across all of the transmit queues, and
the locking mechanism used today only protects concurrency across a given
transmit queue between the transmit and reclaiming. This creates an opportunity
for the SYSTEMPORT hardware to work on corrupted descriptors if we have
multiple producers at once which is the case when using multiple transmit
queues.

This was particularly noticeable when using multiple flows/transmit queues and
it showed up in interesting ways in that UDP packets would get a correct UDP
header checksum being calculated over an incorrect packet length. Similarly TCP
packets would get an equally correct checksum computed by the hardware over an
incorrect packet length.

The SYSTEMPORT hardware maintains an internal descriptor list that it re-arranges
when the driver produces a new descriptor anytime it writes to the
WRITE_PORT_{HI,LO} registers, there is however some delay in the hardware to
re-organize its descriptors and it is possible that concurrent TX queues
eventually break this internal allocation scheme to the point where the
length/status part of the descriptor gets used for an incorrect data buffer.

The fix is to impose a global serialization for all TX queues in the short
section where we are writing to the WRITE_PORT_{HI,LO} registers which solves
the corruption even with multiple concurrent TX queues being used.

Fixes: 80105bef ("net: systemport: add Broadcom SYSTEMPORT Ethernet MAC driver")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20211215202450.4086240-1-f.fainelli@gmail.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

In nginx/wrk benchmark, there's a hung problem with high probability
on case likes that: (client will last several minutes to exit)

server: smc_run nginx

client: smc_run wrk -c 10000 -t 1 http://server

Client hangs with the following backtrace:

0 [ffffa7ce8Of3bbf8] __schedule at ffffffff9f9eOd5f
1 [ffffa7ce8Of3bc88] schedule at ffffffff9f9eløe6
2 [ffffa7ce8Of3bcaO] schedule_timeout at ffffffff9f9e3f3c
3 [ffffa7ce8Of3bd2O] wait_for_common at ffffffff9f9el9de
4 [ffffa7ce8Of3bd8O] __flush_work at ffffffff9fOfeOl3
5 [ffffa7ce8øf3bdfO] smc_release at ffffffffcO697d24 [smc]
6 [ffffa7ce8Of3be2O] __sock_release at ffffffff9f8O2e2d
7 [ffffa7ce8Of3be4ø] sock_close at ffffffff9f8ø2ebl
8 [ffffa7ce8øf3be48] __fput at ffffffff9f334f93
9 [ffffa7ce8Of3be78] task_work_run at ffffffff9flOlff5
10 [ffffa7ce8Of3beaO] do_exit at ffffffff9fOe5Ol2
11 [ffffa7ce8Of3bflO] do_group_exit at ffffffff9fOe592a
12 [ffffa7ce8Of3bf38] __x64_sys_exit_group at ffffffff9fOe5994
13 [ffffa7ce8Of3bf4O] do_syscall_64 at ffffffff9f9d4373
14 [ffffa7ce8Of3bfsO] entry_SYSCALL_64_after_hwframe at ffffffff9fa0007c

This issue dues to flush_work(), which is used to wait for
smc_connect_work() to finish in smc_release(). Once lots of
smc_connect_work() was pending or all executing work dangling,
smc_release() has to block until one worker comes to free, which
is equivalent to wait another smc_connnect_work() to finish.

In order to fix this, There are two changes:

1. For those idle smc_connect_work(), cancel it from the workqueue; for
   executing smc_connect_work(), waiting for it to finish. For that
   purpose, replace flush_work() with cancel_work_sync().

2. Since smc_connect() hold a reference for passive closing, if
   smc_connect_work() has been cancelled, release the reference.

Fixes: 24ac3a08 ("net/smc: rebuild nonblocking connect")
Reported-by: Tony Lu <tonylu@linux.alibaba.com>
Tested-by: Dust Li <dust.li@linux.alibaba.com>
Reviewed-by: Dust Li <dust.li@linux.alibaba.com>
Reviewed-by: Tony Lu <tonylu@linux.alibaba.com>
Signed-off-by: D. Wythe <alibuda@linux.alibaba.com>
Acked-by: Karsten Graul <kgraul@linux.ibm.com>
Link: https://lore.kernel.org/r/1639571361-101128-1-git-send-email-alibuda@linux.alibaba.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Merge tag 'tegra-for-5.16-soc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux into arm/fixes

soc/tegra: Fixes for v5.16-rc6

This contains a single build fix without which ARM allmodconfig builds
are broken if -Werror is enabled.

* tag 'tegra-for-5.16-soc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
  soc/tegra: fuse: Fix bitwise vs. logical OR warning

Link: https://lore.kernel.org/r/20211215162618.3568474-1-thierry.reding@gmail.comSigned-off-by: Arnd Bergmann <arnd@arndb.de>

When printing netdev features %pNF already takes care of the 0x prefix,
remove the explicit one.

Fixes: 6413139d ("skbuff: increase verbosity when dumping skb data")
Signed-off-by: Gal Pressman <gal@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

We found the stat of rx drops for small pkts does not increment when
build_skb fail, it's not coherent with other mode's rx drops stat.
Signed-off-by: Wenliang Wang <wangwenliang.1995@bytedance.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Debug print uses invalid check to detect if speed is unforced:
(speed != SPEED_UNFORCED) should be used instead of (!speed).

Found by Linux Verification Center (linuxtesting.org) with SVACE.
Signed-off-by: Andrey Eremeev <Axtone4all@yandex.ru>
Fixes: 96a2b40c ("net: dsa: mv88e6xxx: add port's MAC speed setter")
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

The return value of kmalloc() needs to be checked.
To avoid use in efx_nic_update_stats() in case of the failure of alloc.

Fixes: b593b6f1 ("sfc_ef100: statistics gathering")
Signed-off-by: Jiasheng Jiang <jiasheng@iscas.ac.cn>
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

KASAN reports an out-of-bounds read in rk_gmac_setup on the line:

	while (ops->regs[i]) {

This happens for most platforms since the regs flexible array member is
empty, so the memory after the ops structure is being read here.  It
seems that mostly this happens to contain zero anyway, so we get lucky
and everything still works.

To avoid adding redundant data to nearly all the ops structures, add a
new flag to indicate whether the regs field is valid and avoid this loop
when it is not.

Fixes: 3bb3d6b1 ("net: stmmac: Add RK3566/RK3568 SoC support")
Signed-off-by: John Keeping <john@metanate.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Tony Nguyen says:

====================
Intel Wired LAN Driver Updates 2021-12-15

This series contains updates to igb, igbvf, igc and ixgbe drivers.

Karen moves checks for invalid VF MAC filters to occur earlier for
igb.

Letu Ren fixes a double free issue in igbvf probe.

Sasha fixes incorrect min value being used when calculating for max for
igc.

Robert Schlabbach adds documentation on enabling NBASE-T support for
ixgbe.

Cyril Novikov adds missing initialization of MDIO bus speed for ixgbe.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

This adds the vendor and product IDs for the AT29M2-AF which is a
lan7801-based device.
Signed-off-by: Greg Jesionowski <jesionowskigreg@gmail.com>
Link: https://lore.kernel.org/r/20211214221027.305784-1-jesionowskigreg@gmail.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Packet sockets may switch ring versions. Avoid misinterpreting state
between versions, whose fields share a union. rx_owner_map is only
allocated with a packet ring (pg_vec) and both are swapped together.
If pg_vec is NULL, meaning no packet ring was allocated, then neither
was rx_owner_map. And the field may be old state from a tpacket_v3.

Fixes: 61fad681 ("net/packet: tpacket_rcv: avoid a producer race condition")
Reported-by: Syzbot <syzbot+1ac0994a0a0c55151121@syzkaller.appspotmail.com>
Signed-off-by: Willem de Bruijn <willemb@google.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Link: https://lore.kernel.org/r/20211215143937.106178-1-willemdebruijn.kernel@gmail.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Zero-initialize memory for new map's value in function nsim_bpf_map_alloc
since it may cause a potential kernel information leak issue, as follows:
1. nsim_bpf_map_alloc calls nsim_map_alloc_elem to allocate elements for
a new map.
2. nsim_map_alloc_elem uses kmalloc to allocate map's value, but doesn't
zero it.
3. A user application can use IOCTL BPF_MAP_LOOKUP_ELEM to get specific
element's information in the map.
4. The kernel function map_lookup_elem will call bpf_map_copy_value to get
the information allocated at step-2, then use copy_to_user to copy to the
user buffer.
This can only leak information for an array map.

Fixes: 395cacb5 ("netdevsim: bpf: support fake map offload")
Suggested-by: Jakub Kicinski <kuba@kernel.org>
Acked-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Haimin Zhang <tcs.kernel@gmail.com>
Link: https://lore.kernel.org/r/20211215111530.72103-1-tcs.kernel@gmail.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Unfortunately, with the blamed commit I also added a side effect in the
ethtool stats shown. Because I added two more fields in the per channel
structure without verifying if its size is used in any way, part of the
ethtool statistics were off by 2.
Fix this by not looking up the size of the structure but instead on a
fixed value kept in a macro.

Fixes: fc398bec ("net: dpaa2: add adaptive interrupt coalescing")
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Link: https://lore.kernel.org/r/20211215105831.290070-1-ioana.ciornei@nxp.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

The MDIO bus speed must be initialized before talking to the PHY the first
time in order to avoid talking to it using a speed that the PHY doesn't
support.

This fixes HW initialization error -17 (IXGBE_ERR_PHY_ADDR_INVALID) on
Denverton CPUs (a.k.a. the Atom C3000 family) on ports with a 10Gb network
plugged in. On those devices, HLREG0[MDCSPD] resets to 1, which combined
with the 10Gb network results in a 24MHz MDIO speed, which is apparently
too fast for the connected PHY. PHY register reads over MDIO bus return
garbage, leading to initialization failure.

Reproduced with Linux kernel 4.19 and 5.15-rc7. Can be reproduced using
the following setup:

* Use an Atom C3000 family system with at least one X552 LAN on the SoC
* Disable PXE or other BIOS network initialization if possible
  (the interface must not be initialized before Linux boots)
* Connect a live 10Gb Ethernet cable to an X550 port
* Power cycle (not reset, doesn't always work) the system and boot Linux
* Observe: ixgbe interfaces w/ 10GbE cables plugged in fail with error -17

Fixes: e84db727 ("ixgbe: Introduce function to control MDIO speed")
Signed-off-by: Cyril Novikov <cnovikov@lynx.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

Commit 25058d1c ("dm integrity: use bvec_kmap_local in
__journal_read_write") didn't account for __journal_read_write() later
adding the biovec's bv_offset. As such using bvec_kmap_local() caused
the start of the biovec to be skipped.

Trivial test that illustrates data corruption:

  # integritysetup format /dev/pmem0
  # integritysetup open /dev/pmem0 integrityroot
  # mkfs.xfs /dev/mapper/integrityroot
  ...
  bad magic number
  bad magic number
  Metadata corruption detected at xfs_sb block 0x0/0x1000
  libxfs_writebufr: write verifer failed on xfs_sb bno 0x0/0x1000
  releasing dirty buffer (bulk) to free list!

Fix this by using kmap_local_page() instead of bvec_kmap_local() in
__journal_read_write().

Fixes: 25058d1c ("dm integrity: use bvec_kmap_local in __journal_read_write")
Reported-by: Tony Asleson <tasleson@redhat.com>
Reviewed-by: Heinz Mauelshagen <heinzm@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>

Commit a296d665 ("ixgbe: Add ethtool support to enable 2.5 and 5.0
Gbps support") introduced suppression of the advertisement of NBASE-T
speeds by default, according to Todd Fujinaka to accommodate customers
with network switches which could not cope with advertised NBASE-T
speeds, as posted in the E1000-devel mailing list:

https://sourceforge.net/p/e1000/mailman/message/37106269/

However, the suppression was not documented at all, nor was how to
enable NBASE-T support.

Properly document the NBASE-T suppression and how to enable NBASE-T
support.

Fixes: a296d665 ("ixgbe: Add ethtool support to enable 2.5 and 5.0 Gbps support")
Reported-by: Robert Schlabbach <robert_s@gmx.net>
Signed-off-by: Robert Schlabbach <robert_s@gmx.net>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

The LTR maximum value was incorrectly written using the scale from
the LTR minimum value. This would cause incorrect values to be sent,
in cases where the initial calculation lead to different min/max scales.

Fixes: 707abf06 ("igc: Add initial LTR support")
Suggested-by: Dima Ruinskiy <dima.ruinskiy@intel.com>
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Nechama Kraus <nechamax.kraus@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

In `igbvf_probe`, if register_netdev() fails, the program will go to
label err_hw_init, and then to label err_ioremap. In free_netdev() which
is just below label err_ioremap, there is `list_for_each_entry_safe` and
`netif_napi_del` which aims to delete all entries in `dev->napi_list`.
The program has added an entry `adapter->rx_ring->napi` which is added by
`netif_napi_add` in igbvf_alloc_queues(). However, adapter->rx_ring has
been freed below label err_hw_init. So this a UAF.

In terms of how to patch the problem, we can refer to igbvf_remove() and
delete the entry before `adapter->rx_ring`.

The KASAN logs are as follows:

[   35.126075] BUG: KASAN: use-after-free in free_netdev+0x1fd/0x450
[   35.127170] Read of size 8 at addr ffff88810126d990 by task modprobe/366
[   35.128360]
[   35.128643] CPU: 1 PID: 366 Comm: modprobe Not tainted 5.15.0-rc2+ #14
[   35.129789] Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS rel-1.12.0-59-gc9ba5276e321-prebuilt.qemu.org 04/01/2014
[   35.131749] Call Trace:
[   35.132199]  dump_stack_lvl+0x59/0x7b
[   35.132865]  print_address_description+0x7c/0x3b0
[   35.133707]  ? free_netdev+0x1fd/0x450
[   35.134378]  __kasan_report+0x160/0x1c0
[   35.135063]  ? free_netdev+0x1fd/0x450
[   35.135738]  kasan_report+0x4b/0x70
[   35.136367]  free_netdev+0x1fd/0x450
[   35.137006]  igbvf_probe+0x121d/0x1a10 [igbvf]
[   35.137808]  ? igbvf_vlan_rx_add_vid+0x100/0x100 [igbvf]
[   35.138751]  local_pci_probe+0x13c/0x1f0
[   35.139461]  pci_device_probe+0x37e/0x6c0
[   35.165526]
[   35.165806] Allocated by task 366:
[   35.166414]  ____kasan_kmalloc+0xc4/0xf0
[   35.167117]  foo_kmem_cache_alloc_trace+0x3c/0x50 [igbvf]
[   35.168078]  igbvf_probe+0x9c5/0x1a10 [igbvf]
[   35.168866]  local_pci_probe+0x13c/0x1f0
[   35.169565]  pci_device_probe+0x37e/0x6c0
[   35.179713]
[   35.179993] Freed by task 366:
[   35.180539]  kasan_set_track+0x4c/0x80
[   35.181211]  kasan_set_free_info+0x1f/0x40
[   35.181942]  ____kasan_slab_free+0x103/0x140
[   35.182703]  kfree+0xe3/0x250
[   35.183239]  igbvf_probe+0x1173/0x1a10 [igbvf]
[   35.184040]  local_pci_probe+0x13c/0x1f0

Fixes: d4e0fe01 (igbvf: add new driver to support 82576 virtual functions)
Reported-by: Zheyu Ma <zheyuma97@gmail.com>
Signed-off-by: Letu Ren <fantasquex@gmail.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

Move checking condition of VF MAC filter before clearing
or adding MAC filter to VF to prevent potential blackout caused
by removal of necessary and working VF's MAC filter.

Fixes: 1b8b062a ("igb: add VF trust infrastructure")
Signed-off-by: Karen Sornek <karen.sornek@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

Pull ceph fixes from Ilya Dryomov:
 "An SGID directory handling fix (marked for stable), a metrics
  accounting fix and two fixups to appease static checkers"

* tag 'ceph-for-5.16-rc6' of git://github.com/ceph/ceph-client:
  ceph: fix up non-directory creation in SGID directories
  ceph: initialize pathlen variable in reconnect_caps_cb
  ceph: initialize i_size variable in ceph_sync_read
  ceph: fix duplicate increment of opened_inodes metric

Pull s390 fixes from Heiko Carstens:

 - Add missing handling of R_390_PLT32DBL relocation type in
   arch_kexec_apply_relocations_add(). Clang and the upcoming gcc 11.3
   generate such relocation entries, which our relocation code silently
   ignores, and which finally will result in an endless loop within the
   purgatory code in case of kexec.

 - Add proper handling of errors and print error messages when applying
   relocations

 - Fix duplicate tracking of irq nesting level in entry code

 - Let recordmcount.pl also look for jgnop mnemonic. Starting with
   binutils 2.37 objdump emits a jgnop mnemonic instead of brcl, which
   breaks mcount location detection. This is only a problem if used with
   compilers older than gcc 9, since with gcc 9 and newer compilers
   recordmcount.pl is not used anymore.

 - Remove preempt_disable()/preempt_enable() pair in
   kprobe_ftrace_handler() which was done for all architectures except
   for s390.

 - Update defconfig

* tag 's390-5.16-5' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
  recordmcount.pl: look for jgnop instruction as well as bcrl on s390
  s390/entry: fix duplicate tracking of irq nesting level
  s390: enable switchdev support in defconfig
  s390/kexec: handle R_390_PLT32DBL rela in arch_kexec_apply_relocations_add()
  s390/ftrace: remove preempt_disable()/preempt_enable() pair
  s390/kexec_file: fix error handling when applying relocations
  s390/kexec_file: print some more error messages

Merge tag 'hyperv-fixes-signed-20211214' of git://git.kernel.org/pub/scm/linux/kernel/git/hyperv/linux

Pull hyperv fix from Wei Liu:
 "Build fix from Randy Dunlap"

* tag 'hyperv-fixes-signed-20211214' of git://git.kernel.org/pub/scm/linux/kernel/git/hyperv/linux:
  hv: utils: add PTP_1588_CLOCK to Kconfig to fix build

A new warning in clang points out two instances where boolean
expressions are being used with a bitwise OR instead of logical OR:

drivers/soc/tegra/fuse/speedo-tegra20.c:72:9: warning: use of bitwise '|' with boolean operands [-Wbitwise-instead-of-logical]
                reg = tegra_fuse_read_spare(i) |
                      ^~~~~~~~~~~~~~~~~~~~~~~~~~
                                               ||
drivers/soc/tegra/fuse/speedo-tegra20.c:72:9: note: cast one or both operands to int to silence this warning
drivers/soc/tegra/fuse/speedo-tegra20.c:87:9: warning: use of bitwise '|' with boolean operands [-Wbitwise-instead-of-logical]
                reg = tegra_fuse_read_spare(i) |
                      ^~~~~~~~~~~~~~~~~~~~~~~~~~
                                               ||
drivers/soc/tegra/fuse/speedo-tegra20.c:87:9: note: cast one or both operands to int to silence this warning
2 warnings generated.

The motivation for the warning is that logical operations short circuit
while bitwise operations do not.

In this instance, tegra_fuse_read_spare() is not semantically returning
a boolean, it is returning a bit value. Use u32 for its return type so
that it can be used with either bitwise or boolean operators without any
warnings.

Fixes: 25cd5a39 ("ARM: tegra: Add speedo-based process identification")
Link: https://github.com/ClangBuiltLinux/linux/issues/1488Suggested-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>

Merge tag 'wireless-drivers-2021-12-15' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers

Kalle Valo says:

====================
wireless-drivers fixes for v5.16

Second set of fixes for v5.16, hopefully also the last one. I changed
my email in MAINTAINERS, one crash fix in iwlwifi and some build
problems fixed.

iwlwifi

* fix crash caused by a warning

* fix LED linking problem

brcmsmac

* rework LED dependencies for being consistent with other drivers

mt76

* mt7921: fix build regression
====================
Signed-off-by: David S. Miller <davem@davemloft.net>