kernel/trace/bpf_trace.c: In function 'bpf_event_output':
kernel/trace/bpf_trace.c:312: error: unknown field 'next' specified in initializer
kernel/trace/bpf_trace.c:312: warning: missing braces around initializer
kernel/trace/bpf_trace.c:312: warning: (near initialization for 'raw.frag.<anonymous>')

Fixes: 555c8a86 ("bpf: avoid stack copy and use skb ctx for event output")
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Cc: Alexei Starovoitov <ast@kernel.org>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

VLAN and MQ control was doing DMA from the stack.  Fix it.

Cc: Michael S. Tsirkin <mst@redhat.com>
Cc: "netdev@vger.kernel.org" <netdev@vger.kernel.org>
Signed-off-by: Andy Lutomirski <luto@kernel.org>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

txr->dev_state was not consistently manipulated with the acquisition of
the per-queue lock, after further inspection the lock does not seem
necessary, either the value is read as BNXT_DEV_STATE_CLOSING or 0.

Reported-by: coverity (CID 1339583)
Fixes: c0c050c5 ("bnxt_en: New Broadcom ethernet driver.")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Shmulik Ladkani says:

====================
net: Consider fragmentation of udp tunneled skbs in 'ip_finish_output_gso'

Currently IP fragmentation of GSO segments that exceed dst mtu is
considered only in the ipv4 forwarding case.

There are cases where GSO skbs that are bridged and then udp-tunneled
may have gso_size exceeding the egress device mtu.
It makes sense to fragment them, as in the non GSOed code path.

The exact cases where this behavior is needed is described and addressed
in the 2nd patch.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

net: ip_finish_output_gso: If skb_gso_network_seglen exceeds MTU, allow segmentation for local udp tunneled skbs

Given:
 - tap0 and vxlan0 are bridged
 - vxlan0 stacked on eth0, eth0 having small mtu (e.g. 1400)

Assume GSO skbs arriving from tap0 having a gso_size as determined by
user-provided virtio_net_hdr (e.g. 1460 corresponding to VM mtu of 1500).

After encapsulation these skbs have skb_gso_network_seglen that exceed
eth0's ip_skb_dst_mtu.

These skbs are accidentally passed to ip_finish_output2 AS IS.
Alas, each final segment (segmented either by validate_xmit_skb or by
hardware UFO) would be larger than eth0 mtu.
As a result, those above-mtu segments get dropped on certain networks.

This behavior is not aligned with the NON-GSO case:
Assume a non-gso 1500-sized IP packet arrives from tap0. After
encapsulation, the vxlan datagram is fragmented normally at the
ip_finish_output-->ip_fragment code path.

The expected behavior for the GSO case would be segmenting the
"gso-oversized" skb first, then fragmenting each segment according to
dst mtu, and finally passing the resulting fragments to ip_finish_output2.

'ip_finish_output_gso' already supports this "Slowpath" behavior,
according to the IPSKB_FRAG_SEGS flag, which is only set during ipv4
forwarding (not set in the bridged case).

In order to support the bridged case, we'll mark skbs arriving from an
ingress interface that get udp-encaspulated as "allowed to be fragmented",
causing their network_seglen to be validated by 'ip_finish_output_gso'
(and fragment if needed).

Note the TUNNEL_DONT_FRAGMENT tun_flag is still honoured (both in the
gso and non-gso cases), which serves users wishing to forbid
fragmentation at the udp tunnel endpoint.

Cc: Hannes Frederic Sowa <hannes@stressinduktion.org>
Cc: Florian Westphal <fw@strlen.de>
Signed-off-by: Shmulik Ladkani <shmulik.ladkani@gmail.com>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

This flag indicates whether fragmentation of segments is allowed.

Formerly this policy was hardcoded according to IPSKB_FORWARDED (set by
either ip_forward or ipmr_forward).

Cc: Hannes Frederic Sowa <hannes@stressinduktion.org>
Cc: Florian Westphal <fw@strlen.de>
Signed-off-by: Shmulik Ladkani <shmulik.ladkani@gmail.com>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Michael Chan says:

====================
bnxt_en: Add support for NS2 Nitro.

This series adds support for the embedded version of the
ethernet controller (Nitro) in the North Star 2 SoC.  There are a number
of features not supported and a software workaround for a hardware rx
bug is required for Nitro A0.  Please review.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

A bridge device in NS2 has the same device ID as the ethernet controller.
Add check to avoid probing the bridge device.
Signed-off-by: Prashant Sreedharan <prashant.sreedharan@broadcom.com>
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Allocate special vnic for dropping packets not matching the RX filters.
First vnic is for normal RX packets and the driver will drop all
packets on the 2nd vnic.
Signed-off-by: Prashant Sreedharan <prashant.sreedharan@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Allocate napi for special vnic, packets arriving on this
napi will simply be dropped and the buffers will be replenished back
to the HW.
Signed-off-by: Prashant Sreedharan <prashant.sreedharan@broadcom.com>
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The hardware is unable to drop rx packets not matching the RX filters.  To
workaround it, we create a special VNIC and configure the hardware to
direct all packets not matching the filters to it.  We then setup the
driver to drop packets received on this VNIC.

This patch creates the infrastructure for this VNIC, reserves a
completion ring, and rx rings.  Only shared completion ring mode is
supported.  The next 2 patches add a NAPI to handle packets from this
VNIC and the setup of the VNIC.
Signed-off-by: Prashant Sreedharan <prashant.sreedharan@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Nitro A0 has a hardware bug in the rx path.  The workaround is to create
a special COS context as a path for non-RSS (non-IP) packets.  Without this
workaround, the chip may stall when receiving RSS and non-RSS packets.

Add infrastructure to allow 2 contexts (RSS and CoS) per VNIC.  Allocate
and configure the CoS context for Nitro A0.
Signed-off-by: Prashant Sreedharan <prashant.sreedharan@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Nitro is the embedded version of the ethernet controller in the North
Star 2 SoC.  Add basic code to recognize the chip ID and disable
the features (ntuple, TPA, ring and port statistics) not supported on
Nitro A0.
Signed-off-by: Prashant Sreedharan <prashant.sreedharan@broadcom.com>
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Charles-Antoine Couret says:

====================
Marvell phy: fiber interface configuration

Another patchset to manage correctly the fiber link for some concerned Marvell's
phy like 88E1512.

This patchset fixed the commit log for the third and last commits and a comment
in the first commit.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

These functions used standards registers in a different page
for both interfaces: copper and fiber.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Charles-Antoine Couret <charles-antoine.couret@nexvision.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>

To be correctly initilized, the fiber interface needs
to be configured via autonegociation registers which use
some customs options or registers.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Charles-Antoine Couret <charles-antoine.couret@nexvision.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add support for the fiber receiver error counter in the
statistics. Rename the current counter which is for copper errors to
phy_receive_errors_copper, so it is easy to distinguish copper from
fiber.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Charles-Antoine Couret <charles-antoine.couret@nexvision.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>

For concerned phy, the fiber link is checked before the copper link.
According to datasheet, the link which is up is enabled.

If both links are down, copper link would be used.
To detect fiber link status, we used the real time status
because of troubles with the copper method.

Tested with Marvell 88E1512.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Charles-Antoine Couret <charles-antoine.couret@nexvision.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>

Sergei Shtylyov says:

====================
Fix DMA channel misreporting for the Renesas Ethernet drivers

Here's a set of 2 patches against DaveM's 'net.git' repo fixing up the DMA
channel reporting by 'ifconfig'...
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Currently 'ifconfig' for the Ethernet devices handled by this driver  shows
"DMA chan: ff" while the driver doesn't use any DMA channels. Not assigning
a value to 'net_device::dma' causes 'ifconfig'  to  correctly not report  a
DMA channel.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Currently 'ifconfig' for the Ethernet devices handled by this driver  shows
"DMA chan: ff" while the driver doesn't use any DMA channels. Not assigning
a value to 'net_device::dma' causes 'ifconfig'  to  correctly not report  a
DMA channel.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In 'get_scq', 'dma_alloc_coherent' has been used to allocate some
resources, so we need to free them using 'dma_free_coherent' instead
of 'kfree'.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>

In 'cpmac_open', 'dma_alloc_coherent' has been used to allocate some
resources, so we need to free them using 'dma_free_coherent' instead
of 'kfree'.

Also, we don't need to free these resources if the allocation has failed.
So I have slighly modified the goto label in this case.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>

We should use kfree_skb() instead of kfree() to free an skb.

Fixes: 362899b8 ("macvtap: switch to use skb array")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

There are two generics functions phy_ethtool_{get|set}_link_ksettings,
so we can use them instead of defining the same code in the driver.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The private structure contain a pointer to phydev, but the structure
net_device already contain such pointer. So we can remove the pointer
phydev in the private structure, and update the driver to use the
one contained in struct net_device.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

There are two generics functions phy_ethtool_{get|set}_link_ksettings,
so we can use them instead of defining the same code in the driver.

There was a check on CAP_NET_ADMIN in bfin_mac_ethtool_setsettings,
but this check is already done in dev_ethtool, so no need to repeat
it before calling the generic function.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The private structure contain a pointer to phydev, but the structure
net_device already contain such pointer. So we can remove the pointer
phydev in the private structure, and update the driver to use the
one contained in struct net_device.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

alloc_workqueue replaces deprecated create_singlethread_workqueue().

A dedicated workqueue has been used since the workitem viz
lp->txtimeout_reinit is involved in reinitialization if a TX timeout
occurs, which is necessary to guarantee forward progress in packet
processing. As a network device can be used during memory reclaim, the
workqueue needs forward progress guarantee under memory pressure.
WQ_MEM_RECLAIM has been set to ensure this.

Since there is only a single work item, explicit concurrency limit is
unnecessary here.
Signed-off-by: Bhaktipriya Shridhar <bhaktipriya96@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Should have been obvious, only called from bpf() syscall via map_update_elem()
that calls bpf_fd_array_map_update_elem() under RCU read lock and thus this
must also be in GFP_ATOMIC, of course.

Fixes: 3b1efb19 ("bpf, maps: flush own entries on perf map release")
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

commit 90017acc ("sctp: Add GSO support") didn't register SCTP GSO
offloading for IPv6 and yet didn't put any restrictions on generating
GSO packets while in IPv6, which causes all IPv6 GSO'ed packets to be
silently dropped.

The fix is to properly register the offload this time.

Fixes: 90017acc ("sctp: Add GSO support")
Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Commit d46e416c missed to update some other places which checked for
the socket being TCP-style AND Established state, as Closing state has
some overlapping with the previous understanding of Established.

Without this fix, one of the effects is that some already queued rx
messages may not be readable anymore depending on how the association
teared down, and sending may also not be possible if peer initiated the
shutdown.

Also merge two if() blocks into one condition on sctp_sendmsg().

Cc: Xin Long <lucien.xin@gmail.com>
Fixes: d46e416c ("sctp: sctp should change socket state when shutdown is received")
Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

There are two generics functions phy_ethtool_{get|set}_link_ksettings,
so we can use them instead of defining the same code in the driver.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Dongpo Li says:

====================
Add Hisilicon MDIO bus driver and FEMAC driver

This patch set adds a Hisilicon MDIO bus driver and
a Fast Ethernet MAC(FEMAC) driver.
We also abstract a general interface "of_phy_get_and_connect"
for PHY connect. User will have no bother with getting
"phy-mode" and "phy-handle" any more.

Changes in v1:
- Pass private data structure instead of struct mii_bus
  in MDIO read and write operation.
- Return the error which devm_clk_get() gives when MDIO probe.
- Leave the clock unprepared and disabled on error when MDIO probe.
- Abstract a general interface "of_phy_get_and_connect" for PHY connect.
- Remove the "_reset" suffixes in "reset-names" property.
- Enable tx per-packet interrupt when tx fifo full.
- Remove pointless compatible and add SoC specific compatible.
- Declare only one clock in MAC dts documentation.
- Add standard unit suffixes for "phy-reset-delays".
- Use a smaller NAPI poll weight 16 for our Fast Ethernet MAC.
- Use phy_ethtool_{get|set}_link_ksettings for ethtool ops.
- Use phydev from struct net_device in MAC driver.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch adds the Hisilicon Fast Ethernet MAC(FEMAC) driver.
The FEMAC supports max speed 100Mbps and has been used in many
Hisilicon SoC.
Signed-off-by: Dongpo Li <lidongpo@hisilicon.com>
Reviewed-by: Jiancheng Xue <xuejiancheng@hisilicon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Abstract a general interface "of_phy_get_and_connect"
for PHY connect. User will have no bother with getting
"phy-mode" and "phy-handle" any more.
Suggested-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Dongpo Li <lidongpo@hisilicon.com>
Reviewed-by: Jiancheng Xue <xuejiancheng@hisilicon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch adds a separate driver for the MDIO interface of the
Hisilicon Fast Ethernet MAC.
Signed-off-by: Dongpo Li <lidongpo@hisilicon.com>
Reviewed-by: Jiancheng Xue <xuejiancheng@hisilicon.com>
Acked-by: Rob Herring <robh@kernel.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

TI_CPSW_PHY_SEL depended on TI_CPSW and was selected by the latter. So
there is no reason to have this symbol visible.

A further optimisation would be to put the code for both symbols into a
single module which would allow to not export at least cpsw_phy_sel()
and simplify the module load process.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

It was used err_xxx for labeled statement, it is
not easy to understand, now use free_xxx for labeled
statement.
Signed-off-by: Zhao Qiang <qiang.zhao@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

'uhdlc_priv' has freed twice, drop the first one.
Signed-off-by: Zhao Qiang <qiang.zhao@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>