- 10 Sep, 2017 29 commits
-
-
James Hogan authored
[ Upstream commit 4f32a39d ] The sys_exit trace event takes a single return value for the system call, which MIPS passes the value of the $v0 (result) register, however MIPS returns positive error codes in $v0 with $a3 specifying that $v0 contains an error code. As a result erroring system calls are traced returning positive error numbers that can't always be distinguished from success. Use regs_return_value() to negate the error code if $a3 is set. Fixes: 1d7bf993 ("MIPS: ftrace: Add support for syscall tracepoints.") Signed-off-by:
James Hogan <james.hogan@imgtec.com> Cc: Steven Rostedt <rostedt@goodmis.org> Cc: Ingo Molnar <mingo@redhat.com> Cc: linux-mips@linux-mips.org Cc: <stable@vger.kernel.org> # 3.13+ Patchwork: https://patchwork.linux-mips.org/patch/16651/Acked-by:
Steven Rostedt (VMware) <rostedt@goodmis.org> Signed-off-by:
Ralf Baechle <ralf@linux-mips.org> Signed-off-by:
Sasha Levin <alexander.levin@verizon.com>
-
James Hogan authored
[ Upstream commit 4915e1b0 ] EVA linked loads (LLE) and conditional stores (SCE) should be used on EVA kernels for the MIPS_ATOMIC_SET operation of the sysmips system call, or else the atomic set will apply to the kernel view of the virtual address space (potentially unmapped on EVA kernels) rather than the user view (TLB mapped). Signed-off-by:
-
James Hogan authored
[ Upstream commit 2ec420b2 ] The inline asm retry check in the MIPS_ATOMIC_SET operation of the sysmips system call has been backwards since commit f1e39a4a ("MIPS: Rewrite sysmips(MIPS_ATOMIC_SET, ...) in C with inline assembler") merged in v2.6.32, resulting in the non R10000_LLSC_WAR case retrying until the operation was inatomic, before returning the new value that was probably just written multiple times instead of the old value. Invert the branch condition to fix that particular issue. Fixes: f1e39a4a ("MIPS: Rewrite sysmips(MIPS_ATOMIC_SET, ...) in C with inline assembler") Signed-off-by:
-
Alex Williamson authored
[ Upstream commit 5d6dee80 ] At the point where the kvm-vfio pseudo device wants to release its vfio group reference, we can't always acquire a new reference to make that happen. The group can be in a state where we wouldn't allow a new reference to be added. This new helper function allows a caller to match a file to a group to facilitate this. Given a file and group, report if they match. Thus the caller needs to already have a group reference to match to the file. This allows the deletion of a group without acquiring a new reference. Signed-off-by:
Alex Williamson <alex.williamson@redhat.com> Reviewed-by:
Eric Auger <eric.auger@redhat.com> Reviewed-by:
Paolo Bonzini <pbonzini@redhat.com> Tested-by:
-
Alex Williamson authored
[ Upstream commit 811642d8 ] If vfio_iommu_group_notifier() acquires a group reference and that reference becomes the last reference to the group, then vfio_group_put introduces a deadlock code path where we're trying to unregister from the iommu notifier chain from within a callout of that chain. Use a work_struct to release this reference asynchronously. Signed-off-by:
-
Jaegeuk Kim authored
[ Upstream commit c925dc16 ] This patch copies commit b7f8a09f: "btrfs: Don't clear SGID when inheriting ACLs" written by Jan. Fixes: 07393101 CC: stable@vger.kernel.org Signed-off-by:
Jan Kara <jack@suse.cz> Reviewed-by:
Chao Yu <yuchao0@huawei.com> Reviewed-by:
Jaegeuk Kim <jaegeuk@kernel.org> Signed-off-by:
-
Corey Minyard authored
[ Upstream commit 4495ec6d ] When getting flags, a response to a different message would result in a deadlock because of a missing unlock. Add that unlock and a comment. Found by static analysis. Reported-by:
Dan Carpenter <dan.carpenter@oracle.com> Cc: stable@vger.kernel.org # 3.19 Signed-off-by:
Corey Minyard <cminyard@mvista.com> Signed-off-by:
-
Tony Camuso authored
[ Upstream commit cdea4656 ] A vendor with a system having more than 128 CPUs occasionally encounters the following crash during shutdown. This is not an easily reproduceable event, but the vendor was able to provide the following analysis of the crash, which exhibits the same footprint each time. crash> bt PID: 0 TASK: ffff88017c70ce70 CPU: 5 COMMAND: "swapper/5" #0 [ffff88085c143ac8] machine_kexec at ffffffff81059c8b #1 [ffff88085c143b28] __crash_kexec at ffffffff811052e2 #2 [ffff88085c143bf8] crash_kexec at ffffffff811053d0 #3 [ffff88085c143c10] oops_end at ffffffff8168ef88 #4 [ffff88085c143c38] no_context at ffffffff8167ebb3 #5 [ffff88085c143c88] __bad_area_nosemaphore at ffffffff8167ec49 #6 [ffff88085c143cd0] bad_area_nosemaphore at ffffffff8167edb3 #7 [ffff88085c143ce0] __do_page_fault at ffffffff81691d1e #8 [ffff88085c143d40] do_page_fault at ffffffff81691ec5 #9 [ffff88085c143d70] page_fault at ffffffff8168e188 [exception RIP: unknown or invalid address] RIP: ffffffffa053c800 RSP: ffff88085c143e28 RFLAGS: 00010206 RAX: ffff88017c72bfd8 RBX: ffff88017a8dc000 RCX: ffff8810588b5ac8 RDX: ffff8810588b5a00 RSI: ffffffffa053c800 RDI: ffff8810588b5a00 RBP: ffff88085c143e58 R8: ffff88017c70d408 R9: ffff88017a8dc000 R10: 0000000000000002 R11: ffff88085c143da0 R12: ffff8810588b5ac8 R13: 0000000000000100 R14: ffffffffa053c800 R15: ffff8810588b5a00 ORIG_RAX: ffffffffffffffff CS: 0010 SS: 0018 <IRQ stack> [exception RIP: cpuidle_enter_state+82] RIP: ffffffff81514192 RSP: ffff88017c72be50 RFLAGS: 00000202 RAX: 0000001e4c3c6f16 RBX: 000000000000f8a0 RCX: 0000000000000018 RDX: 0000000225c17d03 RSI: ffff88017c72bfd8 RDI: 0000001e4c3c6f16 RBP: ffff88017c72be78 R8: 000000000000237e R9: 0000000000000018 R10: 0000000000002494 R11: 0000000000000001 R12: ffff88017c72be20 R13: ffff88085c14f8e0 R14: 0000000000000082 R15: 0000001e4c3bb400 ORIG_RAX: ffffffffffffff10 CS: 0010 SS: 0018 This is the corresponding stack trace It has crashed because the area pointed with RIP extracted from timer element is already removed during a shutdown process. The function is smi_timeout(). And we think ffff8810588b5a00 in RDX is a parameter struct smi_info crash> rd ffff8810588b5a00 20 ffff8810588b5a00: ffff8810588b6000 0000000000000000 .`.X............ ffff8810588b5a10: ffff880853264400 ffffffffa05417e0 .D&S......T..... ffff8810588b5a20: 24a024a000000000 0000000000000000 .....$.$........ ffff8810588b5a30: 0000000000000000 0000000000000000 ................ ffff8810588b5a30: 0000000000000000 0000000000000000 ................ ffff8810588b5a40: ffffffffa053a040 ffffffffa053a060 @.S.....`.S..... ffff8810588b5a50: 0000000000000000 0000000100000001 ................ ffff8810588b5a60: 0000000000000000 0000000000000e00 ................ ffff8810588b5a70: ffffffffa053a580 ffffffffa053a6e0 ..S.......S..... ffff8810588b5a80: ffffffffa053a4a0 ffffffffa053a250 ..S.....P.S..... ffff8810588b5a90: 0000000500000002 0000000000000000 ................ Unfortunately the top of this area is already detroyed by someone. But because of two reasonns we think this is struct smi_info 1) The address included in between ffff8810588b5a70 and ffff8810588b5a80: are inside of ipmi_si_intf.c see crash> module ffff88085779d2c0 2) We've found the area which point this. It is offset 0x68 of ffff880859df4000 crash> rd ffff880859df4000 100 ffff880859df4000: 0000000000000000 0000000000000001 ................ ffff880859df4010: ffffffffa0535290 dead000000000200 .RS............. ffff880859df4020: ffff880859df4020 ffff880859df4020 @.Y.... @.Y.... ffff880859df4030: 0000000000000002 0000000000100010 ................ ffff880859df4040: ffff880859df4040 ffff880859df4040 @@.Y....@@.Y.... ffff880859df4050: 0000000000000000 0000000000000000 ................ ffff880859df4060: 0000000000000000 ffff8810588b5a00 .........Z.X.... ffff880859df4070: 0000000000000001 ffff880859df4078 ........x@.Y.... If we regards it as struct ipmi_smi in shutdown process it looks consistent. The remedy for this apparent race is affixed below. Signed-off-by:
Tony Camuso <tcamuso@redhat.com> Cc: stable@vger.kernel.org # 3.19 This was first introduced in 7ea0ed2b ipmi: Make the message handler easier to use for SMI interfaces where some code was moved outside of the rcu_read_lock() and the lock was not added. Signed-off-by:
-
Mario Kleiner authored
[ Upstream commit 564d8a2c ] The late 2009, 27 inch Apple iMac10,1 has an internal eDP display and an external Mini- Displayport output, driven by a DCE-3.2, RV730 Radeon Mobility HD-4670. The machine worked fine in a dual-display setup with eDP panel + externally connected HDMI or DVI-D digital display sink, connected via MiniDP to DVI or HDMI adapter. However, booting the machine single-display with only eDP panel results in a completely black display - even backlight powering off, as soon as the radeon modesetting driver loads. This patch fixes the single dispay eDP case by assigning encoders based on dig->linkb, similar to DCE-4+. While this should not be generally necessary (Alex: "...atom on normal boards should be able to handle any mapping."), Apple seems to use some special routing here. One remaining problem not solved by this patch is that an external Minidisplayport->DP sink does still not work on iMac10,1, whereas external DVI and HDMI sinks continue to work. The problem affects at least all tested kernels since Linux 3.13 - didn't test earlier kernels, so backporting to stable probably makes sense. v2: With the original patch from 2016, Alex was worried it will break other DCE3.2 systems. Use dmi_match() to apply this special encoder assignment only for the Apple iMac 10,1 from late 2009. Signed-off-by:
Mario Kleiner <mario.kleiner.de@gmail.com> Cc: Alex Deucher <alexander.deucher@amd.com> Cc: Michel Dänzer <michel.daenzer@amd.com> Cc: <stable@vger.kernel.org> Signed-off-by:
Alex Deucher <alexander.deucher@amd.com> Signed-off-by:
-
Jiri Olsa authored
[ Upstream commit c46fc042 ] Zorro reported following crash while having enabled syscall tracing (CONFIG_FTRACE_SYSCALLS): Unable to handle kernel pointer dereference at virtual ... Oops: 0011 [#1] SMP DEBUG_PAGEALLOC SNIP Call Trace: ([<000000000024d79c>] ftrace_syscall_enter+0xec/0x1d8) [<00000000001099c6>] do_syscall_trace_enter+0x236/0x2f8 [<0000000000730f1c>] sysc_tracesys+0x1a/0x32 [<000003fffcf946a2>] 0x3fffcf946a2 INFO: lockdep is turned off. Last Breaking-Event-Address: [<000000000022dd44>] rb_event_data+0x34/0x40 ---[ end trace 8c795f86b1b3f7b9 ]--- The crash happens in syscall_get_arguments function for syscalls with zero arguments, that will try to access first argument (args[0]) in event entry, but it's not allocated. Bail out of there are no arguments. Cc: stable@vger.kernel.org Reported-by:
Zorro Lang <zlang@redhat.com> Signed-off-by:
Jiri Olsa <jolsa@kernel.org> Signed-off-by:
Martin Schwidefsky <schwidefsky@de.ibm.com> Signed-off-by:
-
Xiao Ni authored
[ Upstream commit b5d27718 ] The raid5 md device is created by the disks which we don't use the total size. For example, the size of the device is 5G and it just uses 3G of the devices to create one raid5 device. Then change the chunksize and wait reshape to finish. After reshape finishing stop the raid and assemble it again. It fails. mdadm -CR /dev/md0 -l5 -n3 /dev/loop[0-2] --size=3G --chunk=32 --assume-clean mdadm /dev/md0 --grow --chunk=64 wait reshape to finish mdadm -S /dev/md0 mdadm -As The error messages: [197519.814302] md: loop1 does not have a valid v1.2 superblock, not importing! [197519.821686] md: md_import_device returned -22 After reshape the data offset is changed. It selects backwards direction in this condition. In function super_1_load it compares the available space of the underlying device with sb->data_size. The new data offset gets bigger after reshape. So super_1_load returns -EINVAL. rdev->sectors is updated in md_finish_reshape. Then sb->data_size is set in super_1_sync based on rdev->sectors. So add md_finish_reshape in end_reshape. Signed-off-by:
Xiao Ni <xni@redhat.com> Acked-by:
Guoqing Jiang <gqjiang@suse.com> Cc: stable@vger.kernel.org Signed-off-by:
Shaohua Li <shli@fb.com> Signed-off-by:
-
Devin Heitmueller authored
[ Upstream commit 4e0973a9 ] Setting initial standard at the top of cx8800_initdev would cause the first call to cx88_set_tvnorm() to return without programming any registers (leaving the driver saying it's set to NTSC but the hardware isn't programmed). Even worse, any subsequent attempt to explicitly set it to NTSC-M will return success but actually fail to program the underlying registers unless first changing the standard to something other than NTSC-M. Set the initial standard later in the process, and make sure the field is zero at the beginning to ensure that the call always goes through. This regression was introduced in the following commit: commit ccd6f1d4 ("[media] cx88: move width, height and field to core struct") Author: Hans Verkuil <hans.verkuil@cisco.com> [media] cx88: move width, height and field to core struct Signed-off-by:
Devin Heitmueller <dheitmueller@kernellabs.com> Cc: <stable@vger.kernel.org> # for v3.19 and up Signed-off-by:
Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by:
Mauro Carvalho Chehab <mchehab@s-opensource.com> Signed-off-by:
-
Marek Marczykowski-Górecki authored
[ Upstream commit c54590ca ] Userspace application can do a hypercall through /dev/xen/privcmd, and some for some hypercalls argument is a pointers to user-provided structure. When SMAP is supported and enabled, hypervisor can't access. So, lets allow it. The same applies to HYPERVISOR_dm_op, where additionally privcmd driver carefully verify buffer addresses. Cc: stable@vger.kernel.org Signed-off-by:
Marek Marczykowski-Górecki <marmarek@invisiblethingslab.com> Reviewed-by:
Juergen Gross <jgross@suse.com> Signed-off-by:
-
Mikulas Patocka authored
[ Upstream commit f9c79bc0 ] The function flush_signals clears all pending signals for the process. It may be used by kernel threads when we need to prepare a kernel thread for responding to signals. However using this function for an userspaces processes is incorrect - clearing signals without the program expecting it can cause misbehavior. The raid1 and raid5 code uses flush_signals in its request routine because it wants to prepare for an interruptible wait. This patch drops flush_signals and uses sigprocmask instead to block all signals (including SIGKILL) around the schedule() call. The signals are not lost, but the schedule() call won't respond to them. Signed-off-by:
Mikulas Patocka <mpatocka@redhat.com> Cc: stable@vger.kernel.org Acked-by:
NeilBrown <neilb@suse.com> Signed-off-by:
-
Yoshihiro Shimoda authored
[ Upstream commit 59a0879a ] This patch fixes an issue that some registers may be not initialized after resume if the USBHSF_RUNTIME_PWCTRL is not set. Otherwise, if a cable is not connected, the driver will not enable INTENB0.VBSE after resume. And then, the driver cannot detect the VBUS. Fixes: ca8a282a ("usb: gadget: renesas_usbhs: add suspend/resume support") Cc: <stable@vger.kernel.org> # v3.2+ Signed-off-by:
Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com> Signed-off-by:
Felipe Balbi <felipe.balbi@linux.intel.com> Signed-off-by:
-
Johan Hovold authored
[ Upstream commit fe855789 ] Add device-id entry for DATECS FP-2000 fiscal printer needing the NO_UNION_NORMAL quirk. Reported-by:
Anton Avramov <lukav@lukav.com> Cc: stable <stable@vger.kernel.org> Signed-off-by:
Johan Hovold <johan@kernel.org> Acked-by:
Oliver Neukum <oneukum@suse.com> Signed-off-by:
Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by:
-
Colin Ian King authored
[ Upstream commit 446230f5 ] When us->extra is null the driver is not initialized, however, a later call to osd200_scsi_to_ata is made that dereferences us->extra, causing a null pointer dereference. The code currently detects and reports that the driver is not initialized; add a return to avoid the subsequent dereference issue in this check. Thanks to Alan Stern for pointing out that srb->result needs setting to DID_ERROR << 16 Detected by CoverityScan, CID#100308 ("Dereference after null check") Signed-off-by:
Colin Ian King <colin.king@canonical.com> Cc: stable <stable@vger.kernel.org> Acked-by:
Alan Stern <stern@rowland.harvard.edu> Signed-off-by:
-
Mathias Nyman authored
[ Upstream commit 4b895868 ] This off by one in stream_id indexing caused NULL pointer dereference and soft lockup on machines with USB attached SCSI devices connected to a hotpluggable xhci controller. The code that cleans up pending URBs for dead hosts tried to dereference a stream ring at the invalid stream_id 0. ep->stream_info->stream_rings[0] doesn't point to a ring. Start looping stream_id from 1 like in all the other places in the driver, and check that the ring exists before trying to kill URBs on it. Reported-by:
rocko r <rockorequin@gmail.com> Cc: <stable@vger.kernel.org> Signed-off-by:
Mathias Nyman <mathias.nyman@linux.intel.com> Signed-off-by:
-
Mathias Nyman authored
[ Upstream commit a54408d0 ] A uncleared PLC (port link change) bit will prevent furuther port event interrupts for that port. Leaving it uncleared caused get_port_status() to timeout after 20000ms while waiting to get the final port event interrupt for resume -> U0 state change. This is a targeted fix for a specific case where we get a port resume event racing with xhci resume. The port event interrupt handler notices xHC is not yet running and bails out early, leaving PLC uncleared. The whole xhci port resuming needs more attention, but while working on it it anyways makes sense to always ensure PLC is cleared in get_port_status before setting a new link state and waiting for its completion. Cc: <stable@vger.kernel.org> Signed-off-by:
-
Chen Yu authored
[ Upstream commit e60514bd ] Currently we saw a lot of "No irq handler" errors during hibernation, which caused the system hang finally: ata4.00: qc timeout (cmd 0xec) ata4.00: failed to IDENTIFY (I/O error, err_mask=0x4) ata4.00: revalidation failed (errno=-5) ata4: SATA link up 6.0 Gbps (SStatus 133 SControl 300) do_IRQ: 31.151 No irq handler for vector According to above logs, there is an interrupt triggered and it is dispatched to CPU31 with a vector number 151, but there is no handler for it, thus this IRQ will not get acked and will cause an IRQ flood which kills the system. To be more specific, the 31.151 is an interrupt from the AHCI host controller. After some investigation, the reason why this issue is triggered is because the thaw_noirq() function does not restore the MSI/MSI-X settings across hibernation. The scenario is illustrated below: 1. Before hibernation, IRQ 34 is the handler for the AHCI device, which is bound to CPU31. 2. Hibernation starts, the AHCI device is put into low power state. 3. All the nonboot CPUs are put offline, so IRQ 34 has to be migrated to the last alive one - CPU0. 4. After the snapshot has been created, all the nonboot CPUs are brought up again; IRQ 34 remains bound to CPU0. 5. AHCI devices are put into D0. 6. The snapshot is written to the disk. The issue is triggered in step 6. The AHCI interrupt should be delivered to CPU0, however it is delivered to the original CPU31 instead, which causes the "No irq handler" issue. Ying Huang has provided a clue that, in step 3 it is possible that writing to the register might not take effect as the PCI devices have been suspended. In step 3, the IRQ 34 affinity should be modified from CPU31 to CPU0, but in fact it is not. In __pci_write_msi_msg(), if the device is already in low power state, the low level MSI message entry will not be updated but cached. During the device restore process after a normal suspend/resume, pci_restore_msi_state() writes the cached MSI back to the hardware. But this is not the case for hibernation. pci_restore_msi_state() is not currently called in pci_pm_thaw_noirq(), although pci_save_state() has saved the necessary PCI cached information in pci_pm_freeze_noirq(). Restore the PCI status for the device during hibernation. Otherwise the status might be lost across hibernation (for example, settings for MSI, MSI-X, ATS, ACS, IOV, etc.), which might cause problems during hibernation. Suggested-by:
Ying Huang <ying.huang@intel.com> Suggested-by:
Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by:
Chen Yu <yu.c.chen@intel.com> [bhelgaas: changelog] Signed-off-by:
Bjorn Helgaas <bhelgaas@google.com> Reviewed-by:
-
Herbert Xu authored
[ Upstream commit 096f41d3 ] The parsing of sadb_x_ipsecrequest is broken in a number of ways. First of all we're not verifying sadb_x_ipsecrequest_len. This is needed when the structure carries addresses at the end. Worse we don't even look at the length when we parse those optional addresses. The migration code had similar parsing code that's better but it also has some deficiencies. The length is overcounted first of all as it includes the header itself. It also fails to check the length before dereferencing the sa_family field. This patch fixes those problems in parse_sockaddr_pair and then uses it in parse_ipsecrequest. Reported-by:
Andrey Konovalov <andreyknvl@google.com> Signed-off-by:
Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by:
Steffen Klassert <steffen.klassert@secunet.com> Signed-off-by:
-
Oliver O'Halloran authored
[ Upstream commit 2400fd82 ] The workaround for the CELL timebase bug does not correctly mark cr0 as being clobbered. This means GCC doesn't know that the asm block changes cr0 and might leave the result of an unrelated comparison in cr0 across the block, which we then trash, leading to basically random behaviour. Fixes: 859deea9 ("[POWERPC] Cell timebase bug workaround") Cc: stable@vger.kernel.org # v2.6.19+ Signed-off-by:
Oliver O'Halloran <oohall@gmail.com> [mpe: Tweak change log and flag for stable] Signed-off-by:
Michael Ellerman <mpe@ellerman.id.au> Signed-off-by:
-
Anton Blanchard authored
[ Upstream commit 64e756c5 ] From POWER4 onwards, mfocrf() only places the specified CR field into the destination GPR, and the rest of it is set to 0. The PowerPC AS from version 3.0 now requires this behaviour. The emulation code currently puts the entire CR into the destination GPR. Fix it. Fixes: 6888199f ("[POWERPC] Emulate more instructions in software") Cc: stable@vger.kernel.org # v2.6.22+ Signed-off-by:
Anton Blanchard <anton@samba.org> Acked-by:
Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com> Signed-off-by:
-
Anton Blanchard authored
[ Upstream commit 87c4b83e ] The mcrf emulation code was using the CR field number directly as the shift value, without taking into account that CR fields are numbered from 0-7 starting at the high bits. That meant it was looking at the CR fields in the reverse order. Fixes: cf87c3f6 ("powerpc: Emulate icbi, mcrf and conditional-trap instructions") Cc: stable@vger.kernel.org # v3.18+ Signed-off-by:
-
Michael Ellerman authored
[ Upstream commit 01e6a61a ] Although it's not documented anywhere, there is an expectation that atomic64_inc_not_zero() returns a result which fits in an int. This is the behaviour implemented on all arches except powerpc. This has caused at least one bug in practice, in the percpu-refcount code, where the long result from our atomic64_inc_not_zero() was truncated to an int leading to lost references and stuck systems. That was worked around in that code in commit 966d2b04 ("percpu-refcount: fix reference leak during percpu-atomic transition"). To the best of my grepping abilities there are no other callers in-tree which truncate the value, but we should fix it anyway. Because the breakage is subtle and potentially very harmful I'm also tagging it for stable. Code generation is largely unaffected because in most cases the callers are just using the result for a test anyway. In particular the case of fget() that was mentioned in commit a6cf7ed5 ("powerpc/atomic: Implement atomic*_inc_not_zero") generates exactly the same code. Fixes: a6cf7ed5 ("powerpc/atomic: Implement atomic*_inc_not_zero") Cc: stable@vger.kernel.org # v3.4 Noticed-by:
Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by:
-
Maurizio Lombardi authored
[ Upstream commit 62e62ffd ] The enclosure_add_device() function should fail if it can't create the relevant sysfs links. Cc: <stable@vger.kernel.org> Signed-off-by:
Maurizio Lombardi <mlombard@redhat.com> Tested-by:
Douglas Miller <dougmill@linux.vnet.ibm.com> Acked-by:
James Bottomley <jejb@linux.vnet.ibm.com> Signed-off-by:
Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by:
-
Krzysztof Kozlowski authored
[ Upstream commit b556b15d ] of_genpd_del_provider() iterates over list of domain provides and removes matching element thus it has to use safe version of list iteration. Fixes: aa42240a (PM / Domains: Add generic OF-based PM domain look-up) Cc: 3.19+ <stable@vger.kernel.org> # 3.19+ Signed-off-by:
Krzysztof Kozlowski <krzk@kernel.org> Acked-by:
Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by:
-
Krzysztof Kozlowski authored
[ Upstream commit c6e83cac ] pm_genpd_remove_subdomain() iterates over domain's master_links list and removes matching element thus it has to use safe version of list iteration. Fixes: f721889f ("PM / Domains: Support for generic I/O PM domains (v8)") Cc: 3.1+ <stable@vger.kernel.org> # 3.1+ Signed-off-by:
-
Satish Babu Patakokila authored
[ Upstream commit 01b8cedf ] Currently compress driver hardcodes direction as playback to get substream from the stream. This results in getting the incorrect substream for compressed capture usecase. To fix this, remove the hardcoding and derive substream based on the stream direction. Signed-off-by:
Satish Babu Patakokila <sbpata@codeaurora.org> Signed-off-by:
Banajit Goswami <bgoswami@codeaurora.org> Acked-By:
Vinod Koul <vinod.koul@intel.com> Signed-off-by:
Mark Brown <broonie@kernel.org> Cc: stable@vger.kernel.org Signed-off-by:
-
- 01 Sep, 2017 8 commits
-
-
Jason A. Donenfeld authored
[ Upstream commit 329d8230 ] This file is filled with complex cryptography. Thus, the comparisons of MACs and secret keys and curve points and so forth should not add timing attacks, which could either result in a direct forgery, or, given the complexity, some other type of attack. Signed-off-by:
Jason A. Donenfeld <Jason@zx2c4.com> Signed-off-by:
Marcel Holtmann <marcel@holtmann.org> Cc: stable@vger.kernel.org Signed-off-by:
-
Mateusz Jurczyk authored
[ Upstream commit f6a5885f ] Verify that the caller-provided sockaddr structure is large enough to contain the sa_family field, before accessing it in bind() handlers of the AF_NFC socket. Since the syscall doesn't enforce a minimum size of the corresponding memory region, very short sockaddrs (zero or one byte long) result in operating on uninitialized memory while referencing .sa_family. Signed-off-by:
Mateusz Jurczyk <mjurczyk@google.com> Signed-off-by:
Samuel Ortiz <sameo@linux.intel.com> Signed-off-by:
-
Mateusz Jurczyk authored
[ Upstream commit 608c4adf ] Fix the sockaddr length verification in the connect() handler of NFC/LLCP sockets, to compare against the size of the actual structure expected on input (sockaddr_nfc_llcp) instead of its shorter version (sockaddr_nfc). Both structures are defined in include/uapi/linux/nfc.h. The fields specific to the _llcp extended struct are as follows: 276 __u8 dsap; /* Destination SAP, if known */ 277 __u8 ssap; /* Source SAP to be bound to */ 278 char service_name[NFC_LLCP_MAX_SERVICE_NAME]; /* Service name URI */; 279 size_t service_name_len; If the caller doesn't provide a sufficiently long sockaddr buffer, these fields remain uninitialized (and they currently originate from the stack frame of the top-level sys_connect handler). They are then copied by llcp_sock_connect() into internal storage (nfc_llcp_sock structure), and could be subsequently read back through the user-mode getsockname() function (handled by llcp_sock_getname()). This would result in the disclosure of up to ~70 uninitialized bytes from the kernel stack to user-mode clients capable of creating AFC_NFC sockets. Signed-off-by:
Kees Cook <keescook@chromium.org> Signed-off-by:
-
Mateusz Jurczyk authored
[ Upstream commit a0323b97 ] Check that the NFC_ATTR_TARGET_INDEX and NFC_ATTR_PROTOCOLS attributes (in addition to NFC_ATTR_DEVICE_INDEX) are provided by the netlink client prior to accessing them. This prevents potential unhandled NULL pointer dereference exceptions which can be triggered by malicious user-mode programs, if they omit one or both of these attributes. Signed-off-by:
-
Johan Hovold authored
[ Upstream commit 20777bc5 ] Commit 7eda8b8e ("NFC: Use IDR library to assing NFC devices IDs") moved device-id allocation and struct-device initialisation from nfc_allocate_device() to nfc_register_device(). This broke just about every nfc-device-registration error path, which continue to call nfc_free_device() that tries to put the device reference of the now uninitialised (but zeroed) struct device: kobject: '(null)' (ce316420): is not initialized, yet kobject_put() is being called. The late struct-device initialisation also meant that various work queues whose names are derived from the nfc device name were also misnamed: 421 root 0 SW< [(null)_nci_cmd_] 422 root 0 SW< [(null)_nci_rx_w] 423 root 0 SW< [(null)_nci_tx_w] Move the id-allocation and struct-device initialisation back to nfc_allocate_device() and fix up the single call site which did not use nfc_free_device() in its error path. Fixes: 7eda8b8e ("NFC: Use IDR library to assing NFC devices IDs") Cc: stable <stable@vger.kernel.org> # 3.8 Cc: Samuel Ortiz <sameo@linux.intel.com> Signed-off-by:
-
Miaoqing Pan authored
[ Upstream commit bde717ab ] The hard coded register 0x9864 and 0x9924 are invalid for ar9300 chips. Cc: <stable@vger.kernel.org> Signed-off-by:
Miaoqing Pan <miaoqing@codeaurora.org> Signed-off-by:
Kalle Valo <kvalo@qca.qualcomm.com> Signed-off-by:
-
Miaoqing Pan authored
[ Upstream commit cf8ce1ea ] One scenario that could lead to UAF is two threads writing simultaneously to the "tx99" debug file. One of them would set the "start" value to true and follow to ath9k_tx99_init(). Inside the function it would set the sc->tx99_state to true after allocating sc->tx99skb. Then, the other thread would execute write_file_tx99() and call ath9k_tx99_deinit(). sc->tx99_state would be freed. After that, the first thread would continue inside ath9k_tx99_init() and call r = ath9k_tx99_send(sc, sc->tx99_skb, &txctl); that would make use of the freed sc->tx99_skb memory. Cc: <stable@vger.kernel.org> Signed-off-by:
-
Arnd Bergmann authored
[ Upstream commit bd7e31bb ] gcc-7 suggests that an expression using a bitwise not and a bitmask on a 'bool' variable is better written using boolean logic: drivers/media/rc/imon.c: In function 'imon_incoming_scancode': drivers/media/rc/imon.c:1725:22: error: '~' on a boolean expression [-Werror=bool-operation] ictx->pad_mouse = ~(ictx->pad_mouse) & 0x1; ^ drivers/media/rc/imon.c:1725:22: note: did you mean to use logical not? I agree. Fixes: 21677cfc ("V4L/DVB: ir-core: add imon driver") Signed-off-by:
Arnd Bergmann <arnd@arndb.de> Signed-off-by:
-
- 05 Aug, 2017 2 commits
-
-
Sasha Levin authored
Signed-off-by: -
Benjamin Tissoires authored
[ Upstream commit 50220dea ] Plugging a Logitech DJ receiver with KASAN activated raises a bunch of out-of-bound readings. The fields are allocated up to MAX_USAGE, meaning that potentially, we do not have enough fields to fit the incoming values. Add checks and silence KASAN. Signed-off-by:
Benjamin Tissoires <benjamin.tissoires@redhat.com> Signed-off-by:
Jiri Kosina <jkosina@suse.cz> Signed-off-by:
-
- 31 Jul, 2017 1 commit
-
-
Sasha Levin authored
[ Upstream commit 3c5ab3f3 ] We do not check if packet from real server is for NAT connection before performing SNAT. This causes problems for setups that use DR/TUN and allow local clients to access the real server directly, for example: - local client in director creates IPVS-DR/TUN connection CIP->VIP and the request packets are routed to RIP. Talks are finished but IPVS connection is not expired yet. - second local client creates non-IPVS connection CIP->RIP with same reply tuple RIP->CIP and when replies are received on LOCAL_IN we wrongly assign them for the first client connection because RIP->CIP matches the reply direction. As result, IPVS SNATs replies for non-IPVS connections. The problem is more visible to local UDP clients but in rare cases it can happen also for TCP or remote clients when the real server sends the reply traffic via the director. So, better to be more precise for the reply traffic. As replies are not expected for DR/TUN connections, better to not touch them. Reported-by:
Nick Moriarty <nick.moriarty@york.ac.uk> Tested-by:
Julian Anastasov <ja@ssi.bg> Signed-off-by:
Simon Horman <horms@verge.net.au> Signed-off-by:
-
