The spin lock in requeue_io() was held for too long, allowing deadlock.
Don't worry, due to other issues addressed in the following "dm thin:
fix noflush suspend IO queueing" commit, this code was never called.

Fix this by taking the spin lock for a much shorter period of time.
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>

Ideally a thin pool would never run out of data space; the low water
mark would trigger userland to extend the pool before we completely run
out of space.  However, many small random IOs to unprovisioned space can
consume data space at an alarming rate.  Adjust your low water mark if
you're frequently seeing "out-of-data-space" mode.

Before this fix, if data space ran out the pool would be put in
PM_READ_ONLY mode which also aborted the pool's current metadata
transaction (data loss for any changes in the transaction).  This had a
side-effect of needlessly compromising data consistency.  And retry of
queued unserviceable bios, once the data pool was resized, could
initiate changes to potentially inconsistent pool metadata.

Now when the pool's data space is exhausted transition to a new pool
mode (PM_OUT_OF_DATA_SPACE) that allows metadata to be changed but data
may not be allocated.  This allows users to remove thin volumes or
discard data to recover data space.

The pool is no longer put in PM_READ_ONLY mode in response to the pool
running out of data space.  And PM_READ_ONLY mode no longer aborts the
pool's current metadata transaction.  Also, set_pool_mode() will now
notify userspace when the pool mode is changed.
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>

If a thin metadata operation fails the current transaction will abort,
whereby causing potential for IO layers up the stack (e.g. filesystems)
to have data loss.  As such, set THIN_METADATA_NEEDS_CHECK_FLAG in the
thin metadata's superblock which:
1) requires the user verify the thin metadata is consistent (e.g. use
   thin_check, etc)
2) suggests the user verify the thin data is consistent (e.g. use fsck)

The only way to clear the superblock's THIN_METADATA_NEEDS_CHECK_FLAG is
to run thin_repair.

On metadata operation failure: abort current metadata transaction, set
pool in read-only mode, and now set the needs_check flag.

As part of this change, constraints are introduced or relaxed:
* don't allow a pool to transition to write mode if needs_check is set
* don't allow data or metadata space to be resized if needs_check is set
* if a thin pool's metadata space is exhausted: the kernel will now
  force the user to take the pool offline for repair before the kernel
  will allow the metadata space to be extended.

Also, update Documentation to include information about when the thin
provisioning target commits metadata, how it handles metadata failures
and running out of space.
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Joe Thornber <ejt@redhat.com>

Commit b5330655 ("dm thin: handle metadata failures more consistently")
increased potential for the pool's mode to be changed in response to
metadata operation failures.

When the pool mode is changed it isn't synchronized with the mode in
pool_features stored in the target's context (ti->private) that is used
as the basis for (re)establishing the pool mode during resume via
bind_control_target.

It is important that we synchronize the pool mode when it is changed
otherwise the pool may experience and unexpected mode transition on the
next resume (especially if there was no new table load).
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Acked-by: Joe Thornber <ejt@redhat.com>

Commit 55494bf2 ("dm snapshot: use dm-bufio") broke snapshots.
Before that 3.14-rc1 commit, loading a snapshot's list of exceptions
involved reading exception areas one by one into ps->area and inserting
those exceptions into the hash table.  Commit 55494bf2 changed
it so that dm-bufio with prefetch is used to load exceptions in batchs.
Exceptions are loaded correctly, but ps->area is left uninitialized.
When a new exception is allocated, it is stored in this uninitialized
ps->area which will be written to the disk.  This causes metadata
corruption.

Fix this corruption by copying the last area that was read via dm-bufio
into ps->area.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>

Since DM_DEBUG_BLOCK_STACK_TRACING is a DM_PERSISTENT_DATA config option
move it from drivers/md/Kconfig to drivers/md/persistent-data/Kconfig.

Doing so fixes indentation for other DM config options.
Signed-off-by: Mike Snitzer <snitzer@redhat.com>

The memory allocated for the multiqueue policy's hash table doesn't need
to be physically contiguous.  Use vzalloc() instead of kzalloc().
Fedora has been carrying this fix since 10/10/2013.

Failure seen during creation of a 10TB cached device with a 2048 sector
block size and 411GB cache size:

 dmsetup: page allocation failure: order:9, mode:0x10c0d0
 CPU: 11 PID: 29235 Comm: dmsetup Not tainted 3.10.4 #3
 Hardware name: Supermicro X8DTL/X8DTL, BIOS 2.1a       12/30/2011
  000000000010c0d0 ffff880090941898 ffffffff81387ab4 ffff880090941928
  ffffffff810bb26f 0000000000000009 000000000010c0d0 ffff880090941928
  ffffffff81385dbc ffffffff815f3840 ffffffff00000000 000002000010c0d0
 Call Trace:
  [<ffffffff81387ab4>] dump_stack+0x19/0x1b
  [<ffffffff810bb26f>] warn_alloc_failed+0x110/0x124
  [<ffffffff81385dbc>] ? __alloc_pages_direct_compact+0x17c/0x18e
  [<ffffffff810bda2e>] __alloc_pages_nodemask+0x6c7/0x75e
  [<ffffffff810bdad7>] __get_free_pages+0x12/0x3f
  [<ffffffff810ea148>] kmalloc_order_trace+0x29/0x88
  [<ffffffff810ec1fd>] __kmalloc+0x36/0x11b
  [<ffffffffa031eeed>] ? mq_create+0x1dc/0x2cf [dm_cache_mq]
  [<ffffffffa031efc0>] mq_create+0x2af/0x2cf [dm_cache_mq]
  [<ffffffffa0314605>] dm_cache_policy_create+0xa7/0xd2 [dm_cache]
  [<ffffffffa0312530>] ? cache_ctr+0x245/0xa13 [dm_cache]
  [<ffffffffa031263e>] cache_ctr+0x353/0xa13 [dm_cache]
  [<ffffffffa012b916>] dm_table_add_target+0x227/0x2ce [dm_mod]
  [<ffffffffa012e8e4>] table_load+0x286/0x2ac [dm_mod]
  [<ffffffffa012e65e>] ? dev_wait+0x8a/0x8a [dm_mod]
  [<ffffffffa012e324>] ctl_ioctl+0x39a/0x3c2 [dm_mod]
  [<ffffffffa012e35a>] dm_ctl_ioctl+0xe/0x12 [dm_mod]
  [<ffffffff81101181>] vfs_ioctl+0x21/0x34
  [<ffffffff811019d3>] do_vfs_ioctl+0x3b1/0x3f4
  [<ffffffff810f4d2e>] ? ____fput+0x9/0xb
  [<ffffffff81050b6c>] ? task_work_run+0x7e/0x92
  [<ffffffff81101a68>] SyS_ioctl+0x52/0x82
  [<ffffffff81391d92>] system_call_fastpath+0x16/0x1b
Signed-off-by: Heinz Mauelshagen <heinzm@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Cc: stable@vger.kernel.org

When remapping a block to the cache's fast device that is larger than
2TB we must not truncate the destination sector to 32bits.  The 32bit
temporary result of from_cblock() was being overflowed in
remap_to_cache() due to the logical left shift.

Use an intermediate 64bit type to store the 32bit from_cblock() result
to fix the overflow.
Signed-off-by: Heinz Mauelshagen <heinzm@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Cc: stable@vger.kernel.org

It was always intended that a user could provide a thin metadata device
that is larger than the max supported by the on-disk format.  The extra
space would just go unused.

Unfortunately that never worked.  If the user attempted to use a larger
metadata device on creation they would get an error like the following:

 device-mapper: space map common: space map too large
 device-mapper: transaction manager: couldn't create metadata space map
 device-mapper: thin metadata: tm_create_with_sm failed
 device-mapper: table: 252:17: thin-pool: Error creating metadata object
 device-mapper: ioctl: error adding target to table

Fix this by allowing the initial metadata space map creation to cap its
size at the max number of blocks supported (DM_SM_METADATA_MAX_BLOCKS).
get_metadata_dev_size() must also impose DM_SM_METADATA_MAX_BLOCKS (via
THIN_METADATA_MAX_SECTORS), otherwise extending metadata would cap at
THIN_METADATA_MAX_SECTORS_WARNING (which is larger than supported).

Also, the calculation for THIN_METADATA_MAX_SECTORS didn't account for
the sizeof the disk_bitmap_header.  So the supported maximum metadata
size is a bit smaller (reduced from 33423360 to 33292800 sectors).

Lastly, remove the "excess space will not be used" warning message from
get_metadata_dev_size(); it resulted in printing the warning multiple
times.  Factor out warn_if_metadata_device_too_big(), call it from
pool_ctr() and maybe_resize_metadata_dev().
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Acked-by: Joe Thornber <ejt@redhat.com>

An invalid ioctl will never be valid, irrespective of whether multipath
has active paths or not.  So for invalid ioctls we do not have to wait
for multipath to activate any paths, but can rather return an error
code immediately.  This fix resolves numerous instances of:

 udevd[]: worker [] unexpectedly returned with status 0x0100

that have been seen during testing.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Cc: stable@vger.kernel.org

dm_pool_close_thin_device() must be called if dm_set_target_max_io_len()
fails in thin_ctr().  Otherwise __pool_destroy() will fail because the
pool will still have an open thin device:

 device-mapper: thin metadata: attempt to close pmd when 1 device(s) are still open
 device-mapper: thin: __pool_destroy: dm_pool_metadata_close() failed.

Also, must establish error code if failing thin_ctr() because the pool
is in fail_io mode.
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Acked-by: Joe Thornber <ejt@redhat.com>
Cc: stable@vger.kernel.org

When restoring bi_end_io, increase bi_remaining before retrying the bio
to avoid BUG_ON(atomic_read(&bio->bi_remaining) <= 0) in bio_endio().
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>

Commit 003b5c57 ("block: Convert drivers
to immutable biovecs") broke dm-mirror due to dm-io breakage.

dm-io had three possible iterators (DM_IO_PAGE_LIST, DM_IO_BVEC,
DM_IO_VMA) that iterate over pages where the I/O should be performed.

The switch to immutable biovecs changed the DM_IO_BVEC iterator to
DM_IO_BIO.  Before this change the iterator stored the pointer to a bio
vector in the dpages structure.  The iterator incremented the pointer in
the dpages structure as it advanced over the pages.  After the immutable
biovecs change, the DM_IO_BIO iterator stores a pointer to the bio in
the dpages structure and uses bio_advance to change the bio as it
advances.

The problem is that the function dispatch_io stores the content of the
dpages structure into the variable old_pages and restores it before
issuing I/O to each of the devices.  Before the change, the statement
"*dp = old_pages;" restored the iterator to its starting position.
After the change, struct dpages holds a pointer to the bio, thus the
statement "*dp = old_pages;" doesn't restore the iterator.

Consequently, in the context of dm-mirror: only the first mirror leg is
written correctly, the kernel locks up when trying to write the other
mirror legs because the number of sectors to write in the where->count
variable doesn't match the number of sectors returned by the iterator.

This patch fixes the bug by partially reverting the original patch - it
changes the code so that struct dpages holds a pointer to the bio vector,
so that the statement "*dp = old_pages;" restores the iterator correctly.

The field "context_u" holds the offset from the beginning of the current
bio vector entry, just like the "bio->bi_iter.bi_bvec_done" field.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>

Commit 905e51b3 ("dm thin: commit outstanding data every second")
introduced a periodic commit.  This commit occurs regardless of whether
any thin devices have made changes.

Fix the periodic commit to check if any of a pool's thin devices have
changed using dm_pool_changed_this_transaction().
Reported-by: Alexander Larsson <alexl@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Acked-by: Joe Thornber <ejt@redhat.com>
Cc: stable@vger.kernel.org

When completing an overwrite bio, in overwrite_endio(), the associated
migration should not be added to the 'completed_migrations' until the
bio's fields are restored with dm_unhook_bio().

Otherwise, do_worker() can race to process 'completed_migrations' before
dm_unhook_bio() -- so the bio's bi_end_io is incorrect.  This is
unlikely to cause any problems given the current code but should be
fixed on the basis of correctness.

Also, the cache's spinlock only needs to be held when manipulating the
'completed_migrations' list -- other changes don't need protection.
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Acked-by: Joe Thornber <ejt@redhat.com>

Commit c9d28d5d ("dm cache: promotion optimisation for writes")
incorrectly placed the 'hook_info' member in the writethrough-only
portion of the per_bio_data structure.

Given that the overwrite optimization may be used for writeback the
'hook_info' member must be placed above the 'cache' member of the
per_bio_data structure.  Any members above 'cache' are available from
both writeback and writethrough modes' per_bio_data structure.
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Acked-by: Joe Thornber <ejt@redhat.com>
Cc: stable@vger.kernel.org # 3.13+

Pull btrfs fixes from Chris Mason:
 "We have a small collection of fixes in my for-linus branch.

  The big thing that stands out is a revert of a new ioctl.  Users
  haven't shipped yet in btrfs-progs, and Dave Sterba found a better way
  to export the information"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs:
  Btrfs: use right clone root offset for compressed extents
  btrfs: fix null pointer deference at btrfs_sysfs_add_one+0x105
  Btrfs: unset DCACHE_DISCONNECTED when mounting default subvol
  Btrfs: fix max_inline mount option
  Btrfs: fix a lockdep warning when cleaning up aborted transaction
  Revert "btrfs: add ioctl to export size of global metadata reservation"

Pull devicetree fixes from Rob Herring:
 "Fix booting on PPC boards.  Changes to of_match_node matching caused
  the serial port on some PPC boards to stop working.  Reverted the
  change and reimplement to split matching between new style compatible
  only matching and fallback to old matching algorithm"

* tag 'dt-fixes-for-3.14' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux:
  of: search the best compatible match first in __of_match_node()
  Revert "OF: base: match each node compatible against all given matches first"

Currently, of_match_node compares each given match against all node's
compatible strings with of_device_is_compatible.

To achieve multiple compatible strings per node with ordering from
specific to generic, this requires given matches to be ordered from
specific to generic. For most of the drivers this is not true and also
an alphabetical ordering is more sane there.

Therefore, this patch introduces a function to match each of the node's
compatible strings against all given compatible matches without type and
name first, before checking the next compatible string. This implies
that node's compatibles are ordered from specific to generic while
given matches can be in any order. If we fail to find such a match
entry, then fall-back to the old method in order to keep compatibility.

Cc: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Kevin Hao <haokexin@gmail.com>
Tested-by: Stephen Chivers <schivers@csc.com>
Signed-off-by: Rob Herring <robh@kernel.org>

Pull SCSI target fixes from Nicholas Bellinger:
 "Mostly minor fixes this time to v3.14-rc1 related changes.  Also
  included is one fix for a free after use regression in persistent
  reservations UNREGISTER logic that is CC'ed to >= v3.11.y stable"

* git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending:
  Target/sbc: Fix protection copy routine
  IB/srpt: replace strict_strtoul() with kstrtoul()
  target: Simplify command completion by removing CMD_T_FAILED flag
  iser-target: Fix leak on failure in isert_conn_create_fastreg_pool
  iscsi-target: Fix SNACK Type 1 + BegRun=0 handling
  target: Fix missing length check in spc_emulate_evpd_83()
  qla2xxx: Remove last vestiges of qla_tgt_cmd.cmd_list
  target: Fix 32-bit + CONFIG_LBDAF=n link error w/ sector_div
  target: Fix free-after-use regression in PR unregister

Pull i2c fixes from Wolfram Sang:
 "i2c has a bugfix and documentation improvements for you"

* 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
  Documentation: i2c: mention ACPI method for instantiating devices
  Documentation: i2c: describe devicetree method for instantiating devices
  i2c: mv64xxx: refactor message start to ensure proper initialization

Merge branches 'irq-urgent-for-linus' and 'irq-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip

Pull irq update from Thomas Gleixner:
 "Fix from the urgent branch: a trivial oneliner adding the missing
  Kconfig dependency curing build failures which have been discovered by
  several build robots.

  The update in the irq-core branch provides a new function in the
  irq/devres code, which is a prerequisite for driver developers to get
  rid of boilerplate code all over the place.

  Not a bugfix, but it has zero impact on the current kernel due to the
  lack of users.  It's simpler to provide the infrastructure to
  interested parties via your tree than fulfilling the wishlist of
  driver maintainers on which particular commit or tag this should be
  based on"

* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  genirq: Add missing irq_to_desc export for CONFIG_SPARSE_IRQ=n

* 'irq-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  genirq: Add devm_request_any_context_irq()

Pull timer fixes from Thomas Gleixner:
 "The following trilogy of patches brings you:

   - fix for a long standing math overflow issue with HZ < 60

   - an onliner fix for a corner case in the dreaded tick broadcast
     mechanism affecting a certain range of AMD machines which are
     infested with the infamous automagic C1E power control misfeature

   - a fix for one of the ARM platforms which allows the kernel to
     proceed and boot instead of stupidly panicing for no good reason.
     The patch is slightly larger than necessary, but it's less ugly
     than the alternative 5 liner"

* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  tick: Clear broadcast pending bit when switching to oneshot
  clocksource: Kona: Print warning rather than panic
  time: Fix overflow when HZ is smaller than 60

Merge tag 'trace-fixes-v3.14-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace

Pull twi tracing fixes from Steven Rostedt:
 "Two urgent fixes in the tracing utility.

  The first is a fix for the way the ring buffer stores timestamps.
  After a restructure of the code was done, the ring buffer timestamp
  logic missed the fact that the first event on a sub buffer is to have
  a zero delta, as the full timestamp is stored on the sub buffer
  itself.  But because the delta was not cleared to zero, the timestamp
  for that event will be calculated as the real timestamp + the delta
  from the last timestamp.  This can skew the timestamps of the events
  and have them say they happened when they didn't really happen.
  That's bad.

  The second fix is for modifying the function graph caller site.  When
  the stop machine was removed from updating the function tracing code,
  it missed updating the function graph call site location.  It is still
  modified as if it is being done via stop machine.  But it's not.  This
  can lead to a GPF and kernel crash if the function graph call site
  happens to lie between cache lines and one CPU is executing it while
  another CPU is doing the update.  It would be a very hard condition to
  hit, but the result is severe enough to have it fixed ASAP"

* tag 'trace-fixes-v3.14-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
  ftrace/x86: Use breakpoints for converting function graph caller
  ring-buffer: Fix first commit on sub-buffer having non-zero delta

Pull x86 EFI fixes from Peter Anvin:
 "A few more EFI-related fixes"

* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/efi: Check status field to validate BGRT header
  x86/efi: Fix 32-bit fallout

Pull ARM SoC fixes from Kevin Hilman:
 "A collection of ARM SoC fixes for v3.14-rc1.

  Mostly a collection of Kconfig, device tree data and compilation fixes
  along with fix to drivers/phy that fixes a boot regression on some
  Marvell mvebu platforms"

* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
  dma: mv_xor: Silence a bunch of LPAE-related warnings
  ARM: ux500: disable msp2 device tree node
  ARM: zynq: Reserve not DMAable space in front of the kernel
  ARM: multi_v7_defconfig: Select CONFIG_SOC_DRA7XX
  ARM: imx6: Initialize low-power mode early again
  ARM: pxa: fix various compilation problems
  ARM: pxa: fix compilation problem on AM300EPD board
  ARM: at91: add Atmel's SAMA5D3 Xplained board
  spi/atmel: document clock properties
  mmc: atmel-mci: document clock properties
  ARM: at91: enable USB host on at91sam9n12ek board
  ARM: at91/dt: fix sama5d3 ohci hclk clock reference
  ARM: at91/dt: sam9263: fix compatibility string for the I2C
  ata: sata_mv: Fix probe failures with optional phys
  drivers: phy: Add support for optional phys
  drivers: phy: Make NULL a valid phy reference
  ARM: fix HAVE_ARM_TWD selection for OMAP and shmobile
  ARM: moxart: move DMA_OF selection to driver
  ARM: hisi: fix kconfig warning on HAVE_ARM_TWD

Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Acked-by: Guenter Roeck <linux@roeck-us.net>

Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

For non compressed extents, iterate_extent_inodes() gives us offsets
that take into account the data offset from the file extent items, while
for compressed extents it doesn't. Therefore we have to adjust them before
placing them in a send clone instruction. Not doing this adjustment leads to
the receiving end requesting for a wrong a file range to the clone ioctl,
which results in different file content from the one in the original send
root.

Issue reproducible with the following excerpt from the test I made for
xfstests:

  _scratch_mkfs
  _scratch_mount "-o compress-force=lzo"

  $XFS_IO_PROG -f -c "truncate 118811" $SCRATCH_MNT/foo
  $XFS_IO_PROG -c "pwrite -S 0x0d -b 39987 92267 39987" $SCRATCH_MNT/foo

  $BTRFS_UTIL_PROG subvolume snapshot -r $SCRATCH_MNT $SCRATCH_MNT/mysnap1

  $XFS_IO_PROG -c "pwrite -S 0x3e -b 80000 200000 80000" $SCRATCH_MNT/foo
  $BTRFS_UTIL_PROG filesystem sync $SCRATCH_MNT
  $XFS_IO_PROG -c "pwrite -S 0xdc -b 10000 250000 10000" $SCRATCH_MNT/foo
  $XFS_IO_PROG -c "pwrite -S 0xff -b 10000 300000 10000" $SCRATCH_MNT/foo

  # will be used for incremental send to be able to issue clone operations
  $BTRFS_UTIL_PROG subvolume snapshot -r $SCRATCH_MNT $SCRATCH_MNT/clones_snap

  $BTRFS_UTIL_PROG subvolume snapshot -r $SCRATCH_MNT $SCRATCH_MNT/mysnap2

  $FSSUM_PROG -A -f -w $tmp/1.fssum $SCRATCH_MNT/mysnap1
  $FSSUM_PROG -A -f -w $tmp/2.fssum -x $SCRATCH_MNT/mysnap2/mysnap1 \
      -x $SCRATCH_MNT/mysnap2/clones_snap $SCRATCH_MNT/mysnap2
  $FSSUM_PROG -A -f -w $tmp/clones.fssum $SCRATCH_MNT/clones_snap \
      -x $SCRATCH_MNT/clones_snap/mysnap1 -x $SCRATCH_MNT/clones_snap/mysnap2

  $BTRFS_UTIL_PROG send $SCRATCH_MNT/mysnap1 -f $tmp/1.snap
  $BTRFS_UTIL_PROG send $SCRATCH_MNT/clones_snap -f $tmp/clones.snap
  $BTRFS_UTIL_PROG send -p $SCRATCH_MNT/mysnap1 \
      -c $SCRATCH_MNT/clones_snap $SCRATCH_MNT/mysnap2 -f $tmp/2.snap

  _scratch_unmount
  _scratch_mkfs
  _scratch_mount

  $BTRFS_UTIL_PROG receive $SCRATCH_MNT -f $tmp/1.snap
  $FSSUM_PROG -r $tmp/1.fssum $SCRATCH_MNT/mysnap1 2>> $seqres.full

  $BTRFS_UTIL_PROG receive $SCRATCH_MNT -f $tmp/clones.snap
  $FSSUM_PROG -r $tmp/clones.fssum $SCRATCH_MNT/clones_snap 2>> $seqres.full

  $BTRFS_UTIL_PROG receive $SCRATCH_MNT -f $tmp/2.snap
  $FSSUM_PROG -r $tmp/2.fssum $SCRATCH_MNT/mysnap2 2>> $seqres.full
Signed-off-by: Filipe David Borba Manana <fdmanana@gmail.com>
Signed-off-by: Chris Mason <clm@fb.com>

bdev is null when disk has disappeared and mounted with
the degrade option

stack trace
---------
btrfs_sysfs_add_one+0x105/0x1c0 [btrfs]
open_ctree+0x15f3/0x1fe0 [btrfs]
btrfs_mount+0x5db/0x790 [btrfs]
? alloc_pages_current+0xa4/0x160
mount_fs+0x34/0x1b0
vfs_kern_mount+0x62/0xf0
do_mount+0x22e/0xa80
? __get_free_pages+0x9/0x40
? copy_mount_options+0x31/0x170
SyS_mount+0x7e/0xc0
system_call_fastpath+0x16/0x1b
---------

reproducer:
-------
mkfs.btrfs -draid1 -mraid1 /dev/sdc /dev/sdd
(detach a disk)
devmgt detach /dev/sdc [1]
mount -o degrade /dev/sdd /btrfs
-------

[1] github.com/anajain/devmgt.git
Signed-off-by: Anand Jain <Anand.Jain@oracle.com>
Tested-by: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Signed-off-by: Chris Mason <clm@fb.com>

Because the offload mechanism can fall back to a standard transfer,
having two seperate initialization states is unfortunate. Let's just
have one state which does things consistently. This fixes a bug where
some preparation was missing when the fallback happened. And it makes
the code much easier to follow. To implement this, we put the check
if offload is possible at the top of the offload setup function.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Tested-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Cc: stable@vger.kernel.org # v3.12+
Fixes: 930ab3d4 (i2c: mv64xxx: Add I2C Transaction Generator support)

Pull USB fixes from Greg KH:
 "Here is a bunch of USB fixes for 3.14-rc3.  Most of these are xhci
  reverts, fixing a bunch of reported issues with USB 3 host controller
  issues that loads of people have been hitting (with the exception of
  kernel developers, all of our machines seem to be working fine, which
  is why these took so long to get resolved...)

  There are some other minor fixes and new device ids, as ususal.  All
  have been in linux-next successfully"

* tag 'usb-3.14-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (22 commits)
  usb: option: blacklist ZTE MF667 net interface
  Revert "usb: xhci: Link TRB must not occur within a USB payload burst"
  Revert "xhci: Avoid infinite loop when sg urb requires too many trbs"
  Revert "xhci: Set scatter-gather limit to avoid failed block writes."
  xhci 1.0: Limit arbitrarily-aligned scatter gather.
  Modpost: fixed USB alias generation for ranges including 0x9 and 0xA
  usb: core: Fix potential memory leak adding dyn USBdevice IDs
  USB: ftdi_sio: add Tagsys RFID Reader IDs
  usb: qcserial: add Netgear Aircard 340U
  usb-storage: enable multi-LUN scanning when needed
  USB: simple: add Dynastream ANT USB-m Stick device support
  usb-storage: add unusual-devs entry for BlackBerry 9000
  usb-storage: restrict bcdDevice range for Super Top in Cypress ATACB
  usb: phy: move some error messages to debug
  usb: ftdi_sio: add Mindstorms EV3 console adapter
  usb: dwc2: fix memory corruption in dwc2 driver
  usb: dwc2: fix role switch breakage
  usb: dwc2: bail out early when booting with "nousb"
  Revert "xhci: replace xhci_read_64() with readq()"
  Revert "xhci: replace xhci_write_64() with writeq()"
  ...

Pull tty/serial driver fixes from Greg KH:
 "Here are a small number of tty/serial driver fixes to resolve reported
  issues with 3.14-rc and earlier (in the case of the vt bugfix).  Some
  of these have been tested and reported by a number of people as the
  tty bugfix was pretty commonly hit on some platforms.

  All have been in linux-next for a while"

* tag 'tty-3.14-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
  vt: Fix secure clear screen
  serial: 8250: Support XR17V35x fraction divisor
  n_tty: Fix stale echo output
  serial: sirf: fix kernel panic caused by unpaired spinlock
  serial: 8250_pci: unbreak last serial ports on NetMos 9865 cards
  n_tty: Fix poll() when TIME_CHAR and MIN_CHAR == 0
  serial: omap: fix rs485 probe on defered pinctrl
  serial: 8250_dw: fix compilation warning when !CONFIG_PM_SLEEP
  serial: omap-serial: Move info message to probe function
  tty: Set correct tty name in 'active' sysfs attribute
  tty: n_gsm: Fix for modems with brk in modem status control
  drivers/tty/hvc: don't use module_init in non-modular hyp. console code

Pull staging driver fixes from Greg KH:
 "Here are a number (lots, I know) of fixes for staging drivers to
  resolve a bunch of reported issues.

  The largest patches here is one revert of a patch that is in 3.14-rc1
  to fix reported problems, and a sync of a usb host driver that
  required some ARM patches to go in before it could be accepted (which
  is why it missed -rc1)

  All of these have been in linux-next for a while with no reported
  issues"

* tag 'staging-3.14-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging: (56 commits)
  staging/rtl8821ae: fix build, depends on MAC80211
  iio: max1363: Use devm_regulator_get_optional for optional regulator
  iio:accel:bma180: Use modifier instead of index in channel specification
  iio: adis16400: Set timestamp as the last element in chan_spec
  iio: ak8975: Fix calculation formula for convert micro tesla to gauss unit
  staging:iio:ad799x fix typo in ad799x_events[]
  iio: mxs-lradc: remove useless scale_available files
  iio: mxs-lradc: fix buffer overflow
  iio:magnetometer:mag3110: Fix output of decimal digits in show_int_plus_micros()
  iio:magnetometer:mag3110: Report busy in _read_raw() / write_raw() when buffer is enabled
  wlags49_h2: Fix overflow in wireless_set_essid()
  xlr_net: Fix missing trivial allocation check
  staging: r8188eu: overflow in rtw_p2p_get_go_device_address()
  staging: r8188eu: array overflow in rtw_mp_ioctl_hdl()
  staging: r8188eu: Fix typo in USB_DEVICE list
  usbip/userspace/libsrc/names.c: memory leak
  gpu: ion: dereferencing an ERR_PTR
  staging: comedi: usbduxsigma: fix unaligned dereferences
  staging: comedi: fix too early cleanup in comedi_auto_config()
  staging: android: ion: dummy: fix an error code
  ...

Merge tag 'driver-core-3.14-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core

Pull driver core fix from Greg KH:
 "Here is a single driver core patch for 3.14-rc3 for the component code
  that Russell has found and fixed"

* tag 'driver-core-3.14-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core:
  drivers/base: fix devres handling for master device

Pull char/misc fixes from Greg KH:
 "Here are some small char/misc driver fixes, along with some
  documentation updates, for 3.14-rc3.  Nothing major, just a number of
  fixes for reported issues"

* tag 'char-misc-3.14-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
  Revert "misc: eeprom: sunxi: Add new compatibles"
  Revert "ARM: sunxi: dt: Convert to the new SID compatibles"
  misc: mic: fix possible signed underflow (undefined behavior) in userspace API
  ARM: sunxi: dt: Convert to the new SID compatibles
  misc: eeprom: sunxi: Add new compatibles
  misc: genwqe: Fix potential memory leak when pinning memory
  Documentation:Update Documentation/zh_CN/arm64/memory.txt
  Documentation:Update Documentation/zh_CN/arm64/booting.txt
  Documentation:Chinese translation of Documentation/arm64/tagged-pointers.txt
  raw: set range for MAX_RAW_DEVS
  raw: test against runtime value of max_raw_minors
  Drivers: hv: vmbus: Don't timeout during the initial connection with host
  Drivers: hv: vmbus: Specify the target CPU that should receive notification
  VME: Correct read/write alignment algorithm
  mei: don't unset read cb ptr on reset
  mei: clear write cb from waiting list on reset

A user was running into errors from an NFS export of a subvolume that had a
default subvol set.  When we mount a default subvol we will use d_obtain_alias()
to find an existing dentry for the subvolume in the case that the root subvol
has already been mounted, or a dummy one is allocated in the case that the root
subvol has not already been mounted.  This allows us to connect the dentry later
on if we wander into the path.  However if we don't ever wander into the path we
will keep DCACHE_DISCONNECTED set for a long time, which angers NFS.  It doesn't
appear to cause any problems but it is annoying nonetheless, so simply unset
DCACHE_DISCONNECTED in the get_default_root case and switch btrfs_lookup() to
use d_materialise_unique() instead which will make everything play nicely
together and reconnect stuff if we wander into the defaul subvol path from a
different way.  With this patch I'm no longer getting the NFS errors when
exporting a volume that has been mounted with a default subvol set.  Thanks,

cc: bfields@fieldses.org
cc: ebiederm@xmission.com
Signed-off-by: Josef Bacik <jbacik@fb.com>
Acked-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: Chris Mason <clm@fb.com>

Currently, the only mount option for max_inline that has any effect is
max_inline=0.  Any other value that is supplied to max_inline will be
adjusted to a minimum of 4k.  Since max_inline has an effective maximum
of ~3900 bytes due to page size limitations, the current behaviour
only has meaning for max_inline=0.

This patch will allow the the max_inline mount option to accept non-zero
values as indicated in the documentation.
Signed-off-by: Mitch Harder <mitch.harder@sabayonlinux.org>
Signed-off-by: Chris Mason <clm@fb.com>

Given now we have 2 spinlock for management of delayed refs,
CONFIG_DEBUG_SPINLOCK=y helped me find this,

[ 4723.413809] BUG: spinlock wrong CPU on CPU#1, btrfs-transacti/2258
[ 4723.414882]  lock: 0xffff880048377670, .magic: dead4ead, .owner: btrfs-transacti/2258, .owner_cpu: 2
[ 4723.417146] CPU: 1 PID: 2258 Comm: btrfs-transacti Tainted: G        W  O 3.12.0+ #4
[ 4723.421321] Call Trace:
[ 4723.421872]  [<ffffffff81680fe7>] dump_stack+0x54/0x74
[ 4723.422753]  [<ffffffff81681093>] spin_dump+0x8c/0x91
[ 4723.424979]  [<ffffffff816810b9>] spin_bug+0x21/0x26
[ 4723.425846]  [<ffffffff81323956>] do_raw_spin_unlock+0x66/0x90
[ 4723.434424]  [<ffffffff81689bf7>] _raw_spin_unlock+0x27/0x40
[ 4723.438747]  [<ffffffffa015da9e>] btrfs_cleanup_one_transaction+0x35e/0x710 [btrfs]
[ 4723.443321]  [<ffffffffa015df54>] btrfs_cleanup_transaction+0x104/0x570 [btrfs]
[ 4723.444692]  [<ffffffff810c1b5d>] ? trace_hardirqs_on_caller+0xfd/0x1c0
[ 4723.450336]  [<ffffffff810c1c2d>] ? trace_hardirqs_on+0xd/0x10
[ 4723.451332]  [<ffffffffa015e5ee>] transaction_kthread+0x22e/0x270 [btrfs]
[ 4723.452543]  [<ffffffffa015e3c0>] ? btrfs_cleanup_transaction+0x570/0x570 [btrfs]
[ 4723.457833]  [<ffffffff81079efa>] kthread+0xea/0xf0
[ 4723.458990]  [<ffffffff81079e10>] ? kthread_create_on_node+0x140/0x140
[ 4723.460133]  [<ffffffff81692aac>] ret_from_fork+0x7c/0xb0
[ 4723.460865]  [<ffffffff81079e10>] ? kthread_create_on_node+0x140/0x140
[ 4723.496521] ------------[ cut here ]------------

----------------------------------------------------------------------

The reason is that we get to call cond_resched_lock(&head_ref->lock) while
still holding @delayed_refs->lock.

So it's different with __btrfs_run_delayed_refs(), where we do drop-acquire
dance before and after actually processing delayed refs.

Here we don't drop the lock, others are not able to add new delayed refs to
head_ref, so cond_resched_lock(&head_ref->lock) is not necessary here.
Signed-off-by: Liu Bo <bo.li.liu@oracle.com>
Signed-off-by: Chris Mason <clm@fb.com>