Commit d01f449c ("of_net: add NVMEM support to of_get_mac_address")
added support for reading the MAC address from an nvmem-cell. This
required changing the logic to return an error pointer upon failure.

If stmmac is loaded before the nvmem provider driver then
of_get_mac_address() return an error pointer with -EPROBE_DEFER.

Propagate this error so the stmmac driver will be probed again after the
nvmem provider driver is loaded.
Default to a random generated MAC address in case of any other error,
instead of using the error pointer as MAC address.

Fixes: d01f449c ("of_net: add NVMEM support to of_get_mac_address")
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Mark switch cases where we are expecting to fall through.

This patch fixes the following warnings:

net/iucv/af_iucv.c: warning: this statement may fall
through [-Wimplicit-fallthrough=]:  => 537:3, 519:6, 2246:6, 510:6

Notice that, in this particular case, the code comment is
modified in accordance with what GCC is expecting to find.
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Mark switch cases where we are expecting to fall through.

This patch fixes the following warnings:

drivers/net/arcnet/com20020-isa.c: warning: this statement may fall
through [-Wimplicit-fallthrough=]:  => 205:13, 203:10, 209:7, 201:11,
207:8
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

On initialization failure we have to delete the local fdb which was
inserted due to the default pvid creation. This problem has been present
since the inception of default_pvid. Note that currently there are 2 cases:
1) in br_dev_init() when br_multicast_init() fails
2) if register_netdevice() fails after calling ndo_init()

This patch takes care of both since br_vlan_flush() is called on both
occasions. Also the new fdb delete would be a no-op on normal bridge
device destruction since the local fdb would've been already flushed by
br_dev_delete(). This is not an issue for ports since nbp_vlan_init() is
called last when adding a port thus nothing can fail after it.

Reported-by: syzbot+88533dc8b582309bf3ee@syzkaller.appspotmail.com
Fixes: 5be5a2df ("bridge: Add filtering support for default_pvid")
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In dequeue_func(), there is an if statement on line 74 to check whether
skb is NULL:
    if (skb)

When skb is NULL, it is used on line 77:
    prefetch(&skb->end);

Thus, a possible null-pointer dereference may occur.

To fix this bug, skb->end is used when skb is not NULL.

This bug is found by a static analysis tool STCheck written by us.

Fixes: 76e3cc12 ("codel: Controlled Delay AQM")
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This removes the mailing list xdp-newbies@vger.kernel.org from the XDP
kernel maintainers entry.

Being in the kernel MAINTAINERS file successfully caused the list to
receive kbuild bot warnings, syzbot reports and sometimes developer
patches. The level of details in these messages, doesn't match the
target audience of the XDP-newbies list. This is based on a survey on
the mailing list, where 73% voted for removal from MAINTAINERS file.
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Acked-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Mark switch cases where we are expecting to fall through.

This patch fixes the following warnings (Building: powerpc allyesconfig):

drivers/net/arcnet/arc-rimi.c: In function 'arcrimi_setup':
include/linux/printk.h:304:2: warning: this statement may fall through [-Wimplicit-fallthrough=]
  printk(KERN_ERR pr_fmt(fmt), ##__VA_ARGS__)
  ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/net/arcnet/arc-rimi.c:365:3: note: in expansion of macro 'pr_err'
   pr_err("Too many arguments\n");
   ^~~~~~
drivers/net/arcnet/arc-rimi.c:366:2: note: here
  case 3:  /* Node ID */
  ^~~~
drivers/net/arcnet/arc-rimi.c:367:8: warning: this statement may fall through [-Wimplicit-fallthrough=]
   node = ints[3];
   ~~~~~^~~~~~~~~
drivers/net/arcnet/arc-rimi.c:368:2: note: here
  case 2:  /* IRQ */
  ^~~~
drivers/net/arcnet/arc-rimi.c:369:7: warning: this statement may fall through [-Wimplicit-fallthrough=]
   irq = ints[2];
   ~~~~^~~~~~~~~
drivers/net/arcnet/arc-rimi.c:370:2: note: here
  case 1:  /* IO address */
  ^~~~
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Mark switch cases where we are expecting to fall through.

This patch fixes the following warnings (Building: powerpc allyesconfig):

drivers/net/arcnet/com90io.c: In function 'com90io_setup':
include/linux/printk.h:304:2: warning: this statement may fall through [-Wimplicit-fallthrough=]
  printk(KERN_ERR pr_fmt(fmt), ##__VA_ARGS__)
  ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/net/arcnet/com90io.c:365:3: note: in expansion of macro 'pr_err'
   pr_err("Too many arguments\n");
   ^~~~~~
drivers/net/arcnet/com90io.c:366:2: note: here
  case 2:  /* IRQ */
  ^~~~
drivers/net/arcnet/com90io.c:367:7: warning: this statement may fall through [-Wimplicit-fallthrough=]
   irq = ints[2];
   ~~~~^~~~~~~~~
drivers/net/arcnet/com90io.c:368:2: note: here
  case 1:  /* IO address */
  ^~~~
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Mark switch cases where we are expecting to fall through.

This patch fixes the following warnings (Building: powerpc allyesconfig):

drivers/net/arcnet/com90xx.c: In function 'com90xx_setup':
include/linux/printk.h:304:2: warning: this statement may fall through [-Wimplicit-fallthrough=]
  printk(KERN_ERR pr_fmt(fmt), ##__VA_ARGS__)
  ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/net/arcnet/com90xx.c:695:3: note: in expansion of macro 'pr_err'
   pr_err("Too many arguments\n");
   ^~~~~~
drivers/net/arcnet/com90xx.c:696:2: note: here
  case 3:  /* Mem address */
  ^~~~
drivers/net/arcnet/com90xx.c:697:9: warning: this statement may fall through [-Wimplicit-fallthrough=]
   shmem = ints[3];
   ~~~~~~^~~~~~~~~
drivers/net/arcnet/com90xx.c:698:2: note: here
  case 2:  /* IRQ */
  ^~~~
drivers/net/arcnet/com90xx.c:699:7: warning: this statement may fall through [-Wimplicit-fallthrough=]
   irq = ints[2];
   ~~~~^~~~~~~~~
drivers/net/arcnet/com90xx.c:700:2: note: here
  case 1:  /* IO address */
  ^~~~
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

It was reported that after resuming from suspend network fails with
error "do_IRQ: 3.38 No irq handler for vector", see [0]. Enabling WoL
can work around the issue, but the only actual fix is to disable MSI.
So let's mimic the behavior of the vendor driver and disable MSI on
all chip versions before RTL8168d.

[0] https://bugzilla.kernel.org/show_bug.cgi?id=204079

Fixes: 6c6aa15f ("r8169: improve interrupt handling")
Reported-by: Dušan Dragić <dragic.dusan@gmail.com>
Tested-by: Dušan Dragić <dragic.dusan@gmail.com>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This reverts commit a6851c61.
It was reported that RTL8111b successfully finishes 1000/Full autoneg
but no data flows. Reverting the original patch fixes the issue.
It seems to be a HW issue with the integrated RTL8211B PHY. This PHY
version used also e.g. on RTL8168d, so better revert the original patch.
Reported-by: Bernhard Held <berny156@gmx.de>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In phylink_parse_fixedlink() the pl->link_config.advertising bits are AND
with pl->supported, pl->supported is zeroed and only the speed/duplex
modes and MII bits are set.
So pl->link_config.advertising always loses the flow control/pause bits.

By setting Pause and Asym_Pause bits in pl->supported, the flow control
work again when devicetree "pause" is set in fixes-link node and the MAC
advertise that is supports pause.

Results with this patch.

Legend:
- DT = 'Pause' is set in the fixed-link in devicetree.
- validate() = ‘Yes’ means phylink_set(mask, Pause) is set in the
  validate().
- flow = results reported my link is Up line.

+-----+------------+-------+
| DT  | validate() | flow  |
+-----+------------+-------+
| Yes | Yes        | rx/tx |
| No  | Yes        | off   |
| Yes | No         | off   |
+-----+------------+-------+

Fixes: 9525ae83 ("phylink: add phylink infrastructure")
Signed-off-by: René van Dorst <opensource@vdorst.com>
Acked-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>

The Dutch consumer grade ISDN network will be shut down on September 1,
2019. This means I'll be converted to some sort of VOIP shortly. At that
point it would be unwise to try to maintain the gigaset driver, even for
odd fixes as I do. So I'll stop maintaining it as a seperate driver and
bump support to CAPI in staging. De facto this means the driver will be
unmaintained, since no-one seems to be working on CAPI.

I've lighty tested the hardware specific modules of this driver (bas-gigaset,
ser-gigaset, and usb-gigaset) for v5.3-rc1. The basic functionality appears to
be working. It's unclear whether anyone still cares. I'm aware of only one
person sort of using the driver a few years ago.

Thanks to Karsten Keil for the ISDN subsystems gigaset was using (I4L and
CAPI). And many thanks to Hansjoerg Lipp and Tilman Schmidt for writing and
upstreaming this driver.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: David S. Miller <davem@davemloft.net>

In rds_rdma_cm_event_handler_cmn(), there are some if statements to
check whether conn is NULL, such as on lines 65, 96 and 112.
But conn is not checked before being used on line 108:
    trans->cm_connect_complete(conn, event);
and on lines 140-143:
    rdsdebug("DISCONNECT event - dropping connection "
            "%pI6c->%pI6c\n", &conn->c_laddr,
            &conn->c_faddr);
    rds_conn_drop(conn);

Thus, possible null-pointer dereferences may occur.

To fix these bugs, conn is checked before being used.

These bugs are found by a static analysis tool STCheck written by us.
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In start_isoc_chain(), usb_alloc_urb() on line 1392 may fail
and return NULL. At this time, fifo->iso[i].urb is assigned to NULL.

Then, fifo->iso[i].urb is used at some places, such as:
LINE 1405:    fill_isoc_urb(fifo->iso[i].urb, ...)
                  urb->number_of_packets = num_packets;
                  urb->transfer_flags = URB_ISO_ASAP;
                  urb->actual_length = 0;
                  urb->interval = interval;
LINE 1416:    fifo->iso[i].urb->...
LINE 1419:    fifo->iso[i].urb->...

Thus, possible null-pointer dereferences may occur.

To fix these bugs, "continue" is added to avoid using fifo->iso[i].urb
when it is NULL.

These bugs are found by a static analysis tool STCheck written by us.
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Saeed Mahameed says:

====================
Mellanox, mlx5 fixes 2019-07-25

This series introduces some fixes to mlx5 driver.

1) Ariel is addressing an issue with enacp flow counter race condition
2) Aya fixes ethtool speed handling
3) Edward fixes modify_cq hw bits alignment
4) Maor fixes RDMA_RX capabilities handling
5) Mark reverses unregister devices order to address an issue with LAG
6) From Tariq,
  - wrong max num channels indication regression
  - TLS counters naming and documentation as suggested by Jakub
  - kTLS, Call WARN_ONCE on netdev mismatch

There is one patch in this series that touches nfp driver to align
TLS statistics names with latest documentation, Jakub is CC'ed.

Please pull and let me know if there is any problem.

For -stable v4.9:
  ('net/mlx5: Use reversed order when unregister devices')

For -stable v4.20
  ('net/mlx5e: Prevent encap flow counter update async to user query')
  ('net/mlx5: Fix modify_cq_in alignment')

For -stable v5.1
  ('net/mlx5e: Fix matching of speed to PRM link modes')

For -stable v5.2
  ('net/mlx5: Add missing RDMA_RX capabilities')
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

The udp_ip4_ind bit is set only for IPv4 UDP non-fragmented packets
so that the hardware can flip the checksum to 0xFFFF if the computed
checksum is 0 per RFC768.

However, this bit had to be set for IPv6 UDP non fragmented packets
as well per hardware requirements. Otherwise, IPv6 UDP packets
with computed checksum as 0 were transmitted by hardware and were
dropped in the network.

In addition to setting this bit for IPv6 UDP, the field is also
appropriately renamed to udp_ind as part of this change.

Fixes: 5eb5f860 ("net: qualcomm: rmnet: Add support for TX checksum offload")
Cc: Sean Tranchetti <stranche@codeaurora.org>
Signed-off-by: Subash Abhinov Kasiviswanathan <subashab@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

ip4ip6/ip6ip6 tunnels run iptunnel_handle_offloads on xmit which
can cause a possible use-after-free accessing iph/ipv6h pointer
since the packet will be 'uncloned' running pskb_expand_head if
it is a cloned gso skb.

Fixes: 0e9a7095 ("ip6_tunnel, ip6_gre: fix setting of DSCP on encapsulated packets")
Signed-off-by: Haishuang Yan <yanhaishuang@cmss.chinamobile.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Make sure the delayed work for stats update is not pending before
wq destruction.
This fixes the module unload path.
The issue is there since day 1.

Fixes: a556c76a ("net: mscc: Add initial Ocelot switch support")
Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Reviewed-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The hw_ver field was initialized to zero. Return the chip revision.
This is relevant for rdma driver.
Signed-off-by: Michal Kalderon <michal.kalderon@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The BroadMobi BM818 M.2 card uses the QMI protocol
Signed-off-by: Bob Ham <bob.ham@puri.sm>
Signed-off-by: Angus Ainslie (Purism) <angus@akkea.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>

Alexei Starovoitov says:

====================
pull-request: bpf 2019-07-25

The following pull-request contains BPF updates for your *net* tree.

The main changes are:

1) fix segfault in libbpf, from Andrii.

2) fix gso_segs access, from Eric.

3) tls/sockmap fixes, from Jakub and John.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

We need the same checks introduced by commit cb9f1b78
("ip: validate header length on virtual device xmit") for
ipip tunnel.

Fixes: cb9f1b78 ("ip: validate header length on virtual device xmit")
Signed-off-by: Haishuang Yan <yanhaishuang@cmss.chinamobile.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

ipv6_flowlabel and ipv6_flowlabel_mgr are missing from
gitignore.  Quentin points out that the original
commit 3fb321fd ("selftests/net: ipv6 flowlabel")
did add ignore entries, they are just missing the "ipv6_"
prefix.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Quentin Monnet <quentin.monnet@netronome.com>
Acked-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Commit 3968d389 ("bnx2x: Fix Multi-Cos.") which enabled multi-cos
feature after prolonged time in driver added some regression causing
numerous issues (sudden reboots, tx timeout etc.) reported by customers.
We plan to backout this commit and submit proper fix once we have root
cause of issues reported with this feature enabled.

Fixes: 3968d389 ("bnx2x: Fix Multi-Cos.")
Signed-off-by: Sudarsana Reddy Kalluru <skalluru@marvell.com>
Signed-off-by: Manish Chopra <manishc@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add missing description of counters.
Split tx_tls_encrypted counter into two, to give packets
and bytes indications.

Fixes: f42c104f ("Documentation: add TLS offload documentation")
Suggested-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

Align to the naming convention in TLS documentation.

Fixes: 51a5e563 ("nfp: tls: add basic statistics")
Suggested-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

A netdev mismatch in the processed TLS SKB should not occur,
and indicates a kernel bug.
Add WARN_ONCE to spot such cases.

Fixes: d2ead1f3 ("net/mlx5e: Add kTLS TX HW offload support")
Suggested-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

This patch prevents a race between user invoked cached counters
query and a neighbor last usage updater.

The cached flow counter stats can be queried by calling
"mlx5_fc_query_cached" which provides the number of bytes and
packets that passed via this flow since the last time this counter
was queried.
It does so by reducting the last saved stats from the current, cached
stats and then updating the last saved stats with the cached stats.
It also provide the lastuse value for that flow.

Since "mlx5e_tc_update_neigh_used_value" needs to retrieve the
last usage time of encapsulation flows, it calls the flow counter
query method periodically and async to user queries of the flow counter
using cls_flower.
This call is causing the driver to update the last reported bytes and
packets from the cache and therefore, future user queries of the flow
stats will return lower than expected number for bytes and packets
since the last saved stats in the driver was updated async to the last
saved stats in cls_flower.

This causes wrong stats presentation of encapsulation flows to user.

Since the neighbor usage updater only needs the lastuse stats from the
cached counter, the fix is to use a dedicated lastuse query call that
returns the lastuse value without synching between the cached stats and
the last saved stats.

Fixes: f6dfb4c3 ("net/mlx5e: Update neighbour 'used' state using HW flow rules counters")
Signed-off-by: Ariel Levkovich <lariel@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

Speed translation is performed based on legacy or extended PTYS
register. Translate speed with respect to:
1) Capability bit of extended PTYS table.
2) User request:
 a) When auto-negotiation is turned on, inspect advertisement whether it
 contains extended link modes.
 b) When auto-negotiation is turned off, speed > 100Gbps (maximal
 speed supported in legacy mode).
With both conditions fulfilled translation is done with extended PTYS
table otherwise use legacy PTYS table.
Without this patch 25/50/100 Gbps speed cannot be set, since try to
configure in extended mode but read from legacy mode.

Fixes: dd1b9e09 ("net/mlx5: ethtool, Allow legacy link-modes configuration via non-extended ptys")
Signed-off-by: Aya Levin <ayal@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

No XSK support in the enhanced IPoIB driver and representors.
Add a profile property to specify this, and enhance the logic
that calculates the max number of channels to take it into
account.

Fixes: db05815b ("net/mlx5e: Add XSK zero-copy support")
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

Fix modify_cq_in alignment to match the device specification.
After this fix the 'cq_umem_valid' field will be in the right offset.

Cc: <stable@vger.kernel.org> # 4.19
Fixes: bd371975 ("net/mlx5: Update mlx5_ifc with DEVX UID bits")
Signed-off-by: Edward Srouji <edwards@mellanox.com>
Reviewed-by: Yishai Hadas <yishaih@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

New flow table type RDMA_RX was added but the MLX5_CAP_FLOW_TABLE_TYPE
didn't handle this new flow table type.
This means that MLX5_CAP_FLOW_TABLE_TYPE returns an empty capability to
this flow table type.

Update both the macro and the maximum supported flow table type to
RDMA_RX.

Fixes: d83eb50e ("net/mlx5: Add support in RDMA RX steering")
Signed-off-by: Maor Gottlieb <maorg@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

When lag is active, which is controlled by the bonded mlx5e netdev, mlx5
interface unregestering must happen in the reverse order where rdma is
unregistered (unloaded) first, to guarantee all references to the lag
context in hardware is removed, then remove mlx5e netdev interface which
will cleanup the lag context from hardware.

Without this fix during destroy of LAG interface, we observed following
errors:
 * mlx5_cmd_check:752:(pid 12556): DESTROY_LAG(0x843) op_mod(0x0) failed,
   status bad parameter(0x3), syndrome (0xe4ac33)
 * mlx5_cmd_check:752:(pid 12556): DESTROY_LAG(0x843) op_mod(0x0) failed,
   status bad parameter(0x3), syndrome (0xa5aee8).

Fixes: a31208b1 ("net/mlx5_core: New init and exit flow for mlx5_core")
Reviewed-by: Parav Pandit <parav@mellanox.com>
Reviewed-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Mark Zhang <markz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

fm_set_max_frm() existed in the Freescale SDK as a callback for an
early_param. When this code was ported to the upstream kernel the
early_param was converted to a module_param making the reference to the
function incorrect. The rest of the comment already does a good job of
explaining the parameter so removing the reference to the non-existent
function seems like the best thing to do.
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Signed-off-by: David S. Miller <davem@davemloft.net>

devm_kzalloc may fail and return NULL. So the null check is needed.
Signed-off-by: Navid Emamdoost <navid.emamdoost@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

devm_kzalloc may fail and return null. So the null check is needed.
Signed-off-by: Navid Emamdoost <navid.emamdoost@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

- v1 -> v2: Move skb_set_owner_w to __tun_build_skb to reduce patch size

Small packets going out of a tap device go through an optimized code
path that uses build_skb() rather than sock_alloc_send_pskb(). The
latter calls skb_set_owner_w(), but the small packet code path does not.

The net effect is that small packets are not owned by the userland
application's socket (e.g. QEMU), while large packets are.
This can be seen with a TCP session, where packets are not owned when
the window size is small enough (around PAGE_SIZE), while they are once
the window grows (note that this requires the host to support virtio
tso for the guest to offload segmentation).
All this leads to inconsistent behaviour in the kernel, especially on
netfilter modules that uses sk->socket (e.g. xt_owner).

Fixes: 66ccbc9c ("tap: use build_skb() for small packet")
Signed-off-by: Alexis Bauvin <abauvin@scaleway.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Leon Romanovsky says:

====================
DIM fixes for 5.3

Those two fixes for recently merged DIM patches, both exposed through
RDMa DIM usage.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

DIM causes to the following warnings during kernel compilation
which indicates that tx_profile and rx_profile are supposed to
be declared in *.c and not in *.h files.

In file included from ./include/rdma/ib_verbs.h:64,
                 from ./include/linux/mlx5/device.h:37,
                 from ./include/linux/mlx5/driver.h:51,
                 from ./include/linux/mlx5/vport.h:36,
                 from drivers/infiniband/hw/mlx5/ib_virt.c:34:
./include/linux/dim.h:326:1: warning: _tx_profile_ defined but not used [-Wunused-const-variable=]
  326 | tx_profile[DIM_CQ_PERIOD_NUM_MODES][NET_DIM_PARAMS_NUM_PROFILES] = {
      | ^~~~~~~~~~
./include/linux/dim.h:320:1: warning: _rx_profile_ defined but not used [-Wunused-const-variable=]
  320 | rx_profile[DIM_CQ_PERIOD_NUM_MODES][NET_DIM_PARAMS_NUM_PROFILES] = {
      | ^~~~~~~~~~

Fixes: 4f75da36 ("linux/dim: Move implementation to .c files")
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Acked-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>