- 26 Jun, 2019 17 commits
-
-
Guido Günther authored
Allow to specify regulators for vcc and iovcc. According to the data sheet the panel wants vcc (2.8V) and iovcc (1.8V) and there's no startup dependency between the two. Signed-off-by:
Guido Günther <agx@sigxcpu.org> Reviewed-by:
Sam Ravnborg <sam@ravnborg.org> Signed-off-by:
-
Guido Günther authored
Document the vcc-supply and iovcc-supply properties of the Rocktech jh057n00900 panel. Signed-off-by:
-
Guido Günther authored
0xBF isn't in any ST7703 data sheet so mark it as unknown. This avoids confusion on whether there is a missing command in that dsi_generic_write_seq() call. Signed-off-by:
-
Guido Günther authored
Add a mail alias as reviewer for the rocktech jh057n00900 panel driver. Signed-off-by:
-
Robert Chiras authored
This patch adds Raydium RM67191 TFT LCD panel driver (MIPI-DSI protocol). Signed-off-by:
Robert Chiras <robert.chiras@nxp.com> Reviewed-by:
Fabio Estevam <festevam@gmail.com> Signed-off-by:
-
Robert Chiras authored
Add dt-bindings documentation for Raydium RM67191 DSI panel. Signed-off-by:
-
Paul Cercueil authored
The Sharp LS020B1DD01D is a simple 2.0" 240x160 16-bit TFT panel. Signed-off-by:
Paul Cercueil <paul@crapouillou.net> Tested-by:
Artur Rojek <contact@artur-rojek.eu> Reviewed-by:
-
Paul Cercueil authored
Add the DRM_BUS_FLAG_SHARP_SIGNALS to the drm_bus_flags enum. This flags can be used when the display must be driven with the Sharp-specific signals SPL, CLS, REV, PS. Signed-off-by:
-
Paul Cercueil authored
The LS020B1DD01D is a 2.0" 240x160 16-bit TFT LCD panel. Signed-off-by:
Rob Herring <robh@kernel.org> Reviewed-by:
-
Paul Cercueil authored
Add support for display panels built around the Novatek NT39016 display controller, as found on e.g. the King Display KD035G6-54NT 24-bit 320x240 3.5" LCD panel which equips the GCW Zero open-source handheld gaming console. Signed-off-by:
Maarten ter Huurne <maarten@treewalker.org> Reviewed-by:
-
Paul Cercueil authored
The KD035G6-54NT is a 3.5" 320x240 24-bit TFT LCD panel. Signed-off-by:
-
Neil Armstrong authored
Add myself as co-maintainer of DRM Bridge Drivers then add Jonas Karlman and Jernej Škrabec as Reviewers of DRM Bridge Drivers. Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Cc: Jonas Karlman <jonas@kwiboo.se> Cc: Andrzej Hajda <a.hajda@samsung.com> Cc: Jernej Škrabec <jernej.skrabec@siol.net> Cc: Daniel Vetter <daniel@ffwll.ch> Signed-off-by:
Neil Armstrong <narmstrong@baylibre.com> Reviewed-by:
Jernej Skrabec <jernej.skrabec@siol.net> Reviewed-by:
Jonas Karlman <jonas@kwiboo.se> Acked-by:
Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by:
Andrzej Hajda <a.hajda@samsung.com> Link: https://patchwork.freedesktop.org/patch/msgid/20190624090851.17859-1-narmstrong@baylibre.com
-
H. Nikolaus Schaller authored
The change adds support for the Ortustech COM37H3M05DTC/99DTC 3.7" TFT LCD panel. Tested on Letux3704. Signed-off-by:
H. Nikolaus Schaller <hns@goldelico.com> Reviewed-by:
-
H. Nikolaus Schaller authored
The change adds support for the Sharp LQ070Y3DG3B 7.0" TFT LCD panel. Tested on Letux7004. Signed-off-by:
-
H. Nikolaus Schaller authored
Signed-off-by:
-
H. Nikolaus Schaller authored
Signed-off-by:
-
H. Nikolaus Schaller authored
Signed-off-by:
-
- 25 Jun, 2019 13 commits
-
-
Paul Cercueil authored
The GiantPlus GPM940B0 is a simple 3.0" 320x240 24-bit TFT panel. Signed-off-by:
-
Paul Cercueil authored
This patch adds MEDIA_BUS_FMT_RGB888_3X8, used for the GiantPlus GPM940B0 24-bit TFT panel, where the RGB components are transferred sequentially on a 8-bit bus. Signed-off-by:
Mauro Carvalho Chehab <mchehab+samsung@kernel.org> Acked-by:
Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by:
-
Paul Cercueil authored
The GPM940B0 is a 3.0" 320x240 24-bit TFT LCD panel. Signed-off-by:
-
Daniel Vetter authored
Only user was the prime import, and drm_prime.c takes care of that now. Reviewed-by:
Eric Anholt <eric@anholt.net> Reviewed-by:
Emil Velikov <emil.velikov@collabora.com> Acked-by:
Rob Clark <robdclark@gmail.com> Signed-off-by:
Daniel Vetter <daniel.vetter@intel.com> Cc: Rob Clark <robdclark@gmail.com> Cc: Sean Paul <sean@poorly.run> Cc: linux-arm-msm@vger.kernel.org Cc: freedreno@lists.freedesktop.org Link: https://patchwork.freedesktop.org/patch/msgid/20190614203615.12639-46-daniel.vetter@ffwll.ch
-
Daniel Vetter authored
Only user was the prime import, and drm_prime.c takes care of that now. Reviewed-by:
Lucas Stach <l.stach@pengutronix.de> Signed-off-by:
-
Daniel Vetter authored
Greg is busy already, but maybe he won't do everything ... Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Reviewed-by:
Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by:
-
Daniel Vetter authored
Thanks to Noralf some good progress already. Reviewed-by:
-
Daniel Vetter authored
Basic helpers have been extracted, now there's a pile more todo still across the entire tree. Reviewed-by:
Daniel Thompson <daniel.thompson@linaro.org> Acked-by:
-
Daniel Vetter authored
I've done that. Reviewed-by:
-
Daniel Vetter authored
This is done in drm_prime.c now. Reviewed-by:
-
Daniel Vetter authored
This is now done in drm_prime.c Acked-by:
-
Daniel Vetter authored
If we use the gem fb helper as the prepare_fb hook, plus the drm_prime.c import helpers now automatically setting obj->resv, we can use the shared helpers to wait for fences instead of rolling our own. Note that this relies on mtk setting drm_fb->obj, which is already done in mtk_drm_framebuffer_init(). Aside: Probably can use the default commit_tail with this again, but I didn't check for that. Reviewed-by:
CK Hu <ck.hu@mediatek.com> Reviewed-by:
-
Daniel Vetter authored
It was only used for prime import, which is now handled by drm_prime.c. Reviewed-by:
-
- 24 Jun, 2019 8 commits
-
-
Rob Herring authored
Convert the tpo,tpg110 panel binding to DT schema. Cc: Thierry Reding <thierry.reding@gmail.com> Cc: Sam Ravnborg <sam@ravnborg.org> Cc: Maxime Ripard <maxime.ripard@bootlin.com> Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Cc: dri-devel@lists.freedesktop.org Reviewed-by:
Linus Walleij <linus.walleij@linaro.org> Signed-off-by:
-
Linus Walleij authored
We need to handle the case when of_drm_find_bridge() returns NULL. Reported-by:
Dan Carpenter <dan.carpenter@oracle.com> Acked-by:
-
Ville Syrjälä authored
Just use a pointer to the display_info rather than make a copy on stack. Cc: Maxime Ripard <maxime.ripard@bootlin.com> Signed-off-by:
Ville Syrjälä <ville.syrjala@linux.intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20190326173810.11979-1-ville.syrjala@linux.intel.comAcked-by:
Maxime Ripard <maxime.ripard@bootlin.com> Reviewed-by:
Daniel Vetter <daniel.vetter@ffwll.ch>
-
Ville Syrjälä authored
WARN if the incoming drm_display_mode has an illegal aspect ratio when converting it to a user mode. This should never happen unless the driver made a mistake and put an invalid value into the aspect ratio. Cc: Ilia Mirkin <imirkin@alum.mit.edu> Signed-off-by:
Alex Deucher <alexander.deucher@amd.com>
-
Ville Syrjälä authored
Don't let userspace feed us any old garbage in the mode aspect ratio flags. Cc: Ilia Mirkin <imirkin@alum.mit.edu> Signed-off-by:
-
Ville Syrjälä authored
enum hdmi_picture_aspect is not a bitmask, so don't use bitwise OR to populate it. Cc: Ilia Mirkin <imirkin@alum.mit.edu> Signed-off-by:
-
Maxime Ripard authored
The commit 3aeeb13d ("drm/modes: Support modes names on the command line") added name support to the DRM modes, and added that name to the debug message. However, that code tests for whether or not the name variable is NULL and only prints it if it's not. Except that that variable is an array, so it will never be NULL. The original intent was to print it only when the name has been specified. Just printing the array directly will achieve the same thing since the drm_cmdline_mode structure that holds it is itself contained in drm_connector, that is allocated with its whole content zero'd. That means that if the name is not declared, the array will be all zeros, which will not print anything. Cc: Nick Desaulniers <ndesaulniers@google.com> Reported-by:
kbuild test robot <lkp@intel.com> Reviewed-by:
-
Matt Redfearn authored
The Synopsys MIPI DSI IP contains a video test pattern generator which is helpful in debugging video timing with connected displays. Add a debugfs directory containing files which allow the VPG to be enabled and disabled, and its orientation to be changed. Signed-off-by:
Matt Redfearn <matt.redfearn@thinci.com> Tested-by:
Yannick Fertré <yannick.fertre@st.com> Reviewed-by:
Philippe Cornu <philippe.cornu@st.com> Signed-off-by:
-
- 23 Jun, 2019 2 commits
-
-
Krzysztof Kozlowski authored
There is no point to print deferred probe messages as errors. Adjust the printks for error paths of obtaining clocks and reset controller. This removes the error message of lima_clk_init() call in favor or specific failure messages inside. Signed-off-by:
Krzysztof Kozlowski <krzk@kernel.org> Signed-off-by:
Qiang Yu <yuq825@gmail.com> Link: https://patchwork.freedesktop.org/patch/msgid/20190621162117.22533-4-krzk@kernel.org
-
Krzysztof Kozlowski authored
Store the PTR_ERR() result in local variable in clock init error path. This makes the code consistent with similar section in regulator init code. Signed-off-by:
-
