When netdev_upper_dev_unlink failed in ipvlan_link_new, need to
unlink the ipvlan dev with upper dev.
Signed-off-by: Gao Feng <fgao@ikuai8.com>
Acked-by: Mahesh Bandewar <maheshb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

If we can't allocate the resources in gigaset_initdriver() then we
should return -ENOMEM instead of zero.

Fixes: 2869b23e ("[PATCH] drivers/isdn/gigaset: new M101 driver (v2)")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Telit LE922A MBIM based composition does not work properly
with altsetting toggle done in cdc_ncm_bind_common.

This patch adds CDC_MBIM_FLAG_AVOID_ALTSETTING_TOGGLE quirk
to avoid this procedure that, instead, is mandatory for
other modems.
Signed-off-by: Daniele Palmas <dnlplm@gmail.com>
Reviewed-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>

Commit 3e3aaf64 ("phy: fix mdiobus module safety") fixed the way we
dealt with MDIO bus module reference count, but sort of introduced a
regression in that, if an Ethernet driver registers its own MDIO bus
driver, as is common, we will end up with the Ethernet driver's
module->refnct set to 1, thus preventing this driver from any removal.

Fix this by comparing the network device's device driver owner against
the MDIO bus driver owner, and only if they are different, increment the
MDIO bus module refcount.

Fixes: 3e3aaf64 ("phy: fix mdiobus module safety")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Hyper-V (and Azure) support using NVGRE which requires some extra space
for encapsulation headers. Because of this the largest allowed TSO
packet is reduced.

For older releases, hard code a fixed reduced value.  For next release,
there is a better solution which uses result of host offload
negotiation.
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Support for setting the RGMII_IDMODE bit was added in the commit
referenced below. However, that commit did not add the symmetrical
clearing of the bit by way of setting it in "mask". Add it here.

Note that the documentation marks clearing this bit as "reserved",
however, according to TI, support for delaying the clock does exist in
the MAC, although it is not officially supported.
We tested this on a board with an RGMII to RGMII link that will not
work unless this bit is cleared.

Fixes: 0fb26c30 ("drivers: net: cpsw-phy-sel: add support to configure rgmii internal delay")
Signed-off-by: Alexandru Gagniuc <alex.g@adaptrum.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge tag 'linux-can-fixes-for-4.9-20161207' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can

Marc Kleine-Budde says:

====================
pull-request: can 2016-12-07

Andrey Konovalov triggered a warning in the CAN RAW layer, which is
fixed by a patch by me.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch adds a check to limit the number of can_filters that can be
set via setsockopt on CAN_RAW sockets. Otherwise allocations > MAX_ORDER
are not prevented resulting in a warning.

Reference: https://lkml.org/lkml/2016/12/2/230Reported-by: Andrey Konovalov <andreyknvl@google.com>
Tested-by: Andrey Konovalov <andreyknvl@google.com>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

Pull sparc fix from David Miller:
 "A use-before-NULL-check from Dan Carpenter"

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc:
  dbri: move dereference after check for NULL

We accidentally introduced a dereference before the NULL check in
xmit_descs() as part of silencing a GCC warning.

Fixes: 16f46050 ("dbri: Fix compiler warning")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pull networking fixes from David Miller:

 1) When dcbnl_cee_fill() fails to be able to push a new netlink
    attribute, it return 0 instead of an error code. From Pan Bian.

 2) Two suffix handling fixes to FIB trie code, from Alexander Duyck.

 3) bnxt_hwrm_stat_ctx_alloc() goes through all the trouble of setting
    and maintaining a return code 'rc' but fails to actually return it.
    Also from Pan Bian.

 4) ping socket ICMP handler needs to validate ICMP header length, from
    Kees Cook.

 5) caif_sktinit_module() has this interesting logic:

        int err = sock_register(...);
        if (!err)
                return err;
        return 0;

    Just return sock_register()'s return value directly which is the
    only possible correct thing to do.

 6) Two bnx2x driver fixes from Yuval Mintz, return a reasonable
    estimate from get_ringparam() ethtool op when interface is down and
    avoid trying to use UDP port based tunneling on 577xx chips.

 7) Fix ep93xx_eth crash on module unload from Florian Fainelli.

 8) Missing uapi exports, from Stephen Hemminger.

 9) Don't schedule work from sk_destruct(), because the socket will be
    freed upon return from that function. From Herbert Xu.

10) Buggy drivers, of which we know there is at least one, can send a
    huge packet into the TCP stack but forget to set the gso_size in the
    SKB, which causes all kinds of problems.

    Correct this when it happens, and emit a one-time warning with the
    device name included so that it can be diagnosed more easily.

    From Marcelo Ricardo Leitner.

11) virtio-net does DMA off the stack causes hiccups with VMAP_STACK,
    fix from Andy Lutomirski.

12) Fix fec driver compilation with CONFIG_M5272, from Nikita
    Yushchenko.

13) mlx5 fixes from Kamal Heib, Saeed Mahameed, and Mohamad Haj Yahia.
    (erroneously flushing queues on error, module parameter validation,
    etc)

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (34 commits)
  net/mlx5e: Change the SQ/RQ operational state to positive logic
  net/mlx5e: Don't flush SQ on error
  net/mlx5e: Don't notify HW when filling the edge of ICO SQ
  net/mlx5: Fix query ISSI flow
  net/mlx5: Remove duplicate pci dev name print
  net/mlx5: Verify module parameters
  net: fec: fix compile with CONFIG_M5272
  be2net: Add DEVSEC privilege to SET_HSW_CONFIG command.
  virtio-net: Fix DMA-from-the-stack in virtnet_set_mac_address()
  tcp: warn on bogus MSS and try to amend it
  uapi glibc compat: fix outer guard of net device flags enum
  net: stmmac: clear reset value of snps, wr_osr_lmt/snps, rd_osr_lmt before writing
  netlink: Do not schedule work from sk_destruct
  uapi: export nf_log.h
  uapi: export tc_skbmod.h
  net: ep93xx_eth: Do not crash unloading module
  bnx2x: Prevent tunnel config for 577xx
  bnx2x: Correct ringparam estimate when DOWN
  isdn: hisax: set error code on failure
  net: bnx2x: fix improper return value
  ...

The shmem hole punching with fallocate(FALLOC_FL_PUNCH_HOLE) does not
want to race with generating new pages by faulting them in.

However, the wait-queue used to delay the page faulting has a serious
problem: the wait queue head (in shmem_fallocate()) is allocated on the
stack, and the code expects that "wake_up_all()" will make sure that all
the queue entries are gone before the stack frame is de-allocated.

And that is not at all necessarily the case.

Yes, a normal wake-up sequence will remove the wait-queue entry that
caused the wakeup (see "autoremove_wake_function()"), but the key
wording there is "that caused the wakeup".  When there are multiple
possible wakeup sources, the wait queue entry may well stay around.

And _particularly_ in a page fault path, we may be faulting in new pages
from user space while we also have other things going on, and there may
well be other pending wakeups.

So despite the "wake_up_all()", it's not at all guaranteed that all list
entries are removed from the wait queue head on the stack.

Fix this by introducing a new wakeup function that removes the list
entry unconditionally, even if the target process had already woken up
for other reasons.  Use that "synchronous" function to set up the
waiters in shmem_fault().

This problem has never been seen in the wild afaik, but Dave Jones has
reported it on and off while running trinity.  We thought we fixed the
stack corruption with the blk-mq rq_list locking fix (commit
7fe31130: "blk-mq: update hardware and software queues for sleeping
alloc"), but it turns out there was _another_ stack corruptor hiding
in the trinity runs.

Vegard Nossum (also running trinity) was able to trigger this one fairly
consistently, and made us look once again at the shmem code due to the
faults often being in that area.

Reported-and-tested-by: Vegard Nossum <vegard.nossum@oracle.com>.
Reported-by: Dave Jones <davej@codemonkey.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Saeed Mahameed says:

====================
Mellanox 100G mlx5 fixes 2016-12-04

Some bug fixes for mlx5 core and mlx5e driver.

v1->v2:
 - replace "uint" with "unsigned int"
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

When using the negative logic (i.e. FLUSH state), after the RQ/SQ reopen
we will have a time interval that the RQ/SQ is not really ready and the
state indicates that its not in FLUSH state because the initial SQ/RQ struct
memory starts as zeros.
Now we changed the state to indicate if the SQ/RQ is opened and we will
set the READY state after finishing preparing all the SQ/RQ resources.

Fixes: 6e8dd6d6 ("net/mlx5e: Don't wait for SQ completions on close")
Fixes: f2fde18c ("net/mlx5e: Don't wait for RQ completions on close")
Signed-off-by: Mohamad Haj Yahia <mohamad@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

We are doing SQ descriptors cleanup in driver.

Fixes: 6e8dd6d6 ("net/mlx5e: Don't wait for SQ completions on close")
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

We are going to do this a couple of steps ahead anyway.

Fixes: d3c9bc27 ("net/mlx5e: Added ICO SQs")
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In old FWs query ISSI command is not supported and for some of those FWs
it might fail with status other than "MLX5_CMD_STAT_BAD_OP_ERR".

In such case instead of failing the driver load, we will treat any FW
status other than 0 for Query ISSI FW command as ISSI not supported and
assume ISSI=0 (most basic driver/FW interface).

In case of driver syndrom (query ISSI failure by driver) we will fail
driver load.

Fixes: f62b8bb8 ('net/mlx5: Extend mlx5_core to support ConnectX-4
Ethernet functionality')
Signed-off-by: Kamal Heib <kamalh@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Remove duplicate pci dev name printing from mlx5_core_warn/dbg.

Fixes: 5a788398 ('net/mlx5_core: Improve mlx5 messages')
Signed-off-by: Kamal Heib <kamalh@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Verify the mlx5_core module parameters by making sure that they are in
the expected range and if they aren't restore them to their default
values.

Fixes: 9603b61d ('mlx5: Move pci device handling from mlx5_ib to mlx5_core')
Signed-off-by: Kamal Heib <kamalh@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Commit 80cca775 ("net: fec: cache statistics while device is down")
introduced unconditional statistics-related actions.

However, when driver is compiled with CONFIG_M5272, staticsics-related
definitions do not exist, which results into build errors.

Fix that by adding explicit handling of !defined(CONFIG_M5272) case.

Fixes: 80cca775 ("net: fec: cache statistics while device is down")
Signed-off-by: Nikita Yushchenko <nikita.yoush@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

OPCODE_COMMON_GET_FN_PRIVILEGES is returning only DEVSEC
privilege (Unrestricted Administrative Privilege) for Lancer NIC functions.
So, driver is failing SET_HSW_CONFIG command, as DEVSEC privilege was not
set in the privilege bitmap. This patch fixes the problem by setting DEVSEC
privilege in SET_HSW_CONFIG’s privilege bitmap.
Signed-off-by: Venkat Duvvuru <venkatkumar.duvvuru@broadcom.com>
Signed-off-by: Suresh Reddy <suresh.reddy@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

With CONFIG_VMAP_STACK=y, virtnet_set_mac_address() can be passed a
pointer to the stack and it will OOPS.  Copy the address to the heap
to prevent the crash.

Cc: Michael S. Tsirkin <mst@redhat.com>
Cc: Jason Wang <jasowang@redhat.com>
Cc: Laura Abbott <labbott@redhat.com>
Reported-by: zbyszek@in.waw.pl
Signed-off-by: Andy Lutomirski <luto@kernel.org>
Acked-by: Jason Wang <jasowang@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

There have been some reports lately about TCP connection stalls caused
by NIC drivers that aren't setting gso_size on aggregated packets on rx
path. This causes TCP to assume that the MSS is actually the size of the
aggregated packet, which is invalid.

Although the proper fix is to be done at each driver, it's often hard
and cumbersome for one to debug, come to such root cause and report/fix
it.

This patch amends this situation in two ways. First, it adds a warning
on when this situation occurs, so it gives a hint to those trying to
debug this. It also limit the maximum probed MSS to the adverised MSS,
as it should never be any higher than that.

The result is that the connection may not have the best performance ever
but it shouldn't stall, and the admin will have a hint on what to look
for.

Tested with virtio by forcing gso_size to 0.

v2: updated msg per David's suggestion
v3: use skb_iif to find the interface and also log its name, per Eric
    Dumazet's suggestion. As the skb may be backlogged and the interface
    gone by then, we need to check if the number still has a meaning.
v4: use helper tcp_gro_dev_warn() and avoid pr_warn_once inside __once, per
    David's suggestion

Cc: Jonathan Maxwell <jmaxwell37@gmail.com>
Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Fix a wrong condition preventing the higher net device flags
IFF_LOWER_UP etc to be defined if net/if.h is included before
linux/if.h.

The comment makes it clear the intention was to allow partial
definition with either parts.

This fixes compilation of userspace programs trying to use
IFF_LOWER_UP, IFF_DORMANT or IFF_ECHO.

Fixes: 4a91cb61 ("uapi glibc compat: fix compile errors when glibc net/if.h included before linux/if.h")
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Reviewed-by: Mikko Rapeli <mikko.rapeli@iki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>

WR_OSR_LMT and RD_OSR_LMT have a reset value of 1.
Since the reset value wasn't cleared before writing, the value in the
register would be incorrect if specifying an uneven value for
snps,wr_osr_lmt/snps,rd_osr_lmt.

Zero is a valid value for the properties, since the databook specifies:
maximum outstanding requests = WR_OSR_LMT + 1.

We do not want to change the behavior for existing users when the
property is missing. Therefore, default to 1 if the property is missing,
since that is the same as the reset value.
Signed-off-by: Niklas Cassel <niklas.cassel@axis.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

It is wrong to schedule a work from sk_destruct using the socket
as the memory reserve because the socket will be freed immediately
after the return from sk_destruct.

Instead we should do the deferral prior to sk_free.

This patch does just that.

Fixes: 707693c8 ("netlink: Call cb->done from a worker thread")
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Tested-by: Andrey Konovalov <andreyknvl@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

File is in uapi directory but not being copied on
 make install_headers

Fixes commit 4ec9c8fbbc22 ("netfilter: nft_log: complete
NFTA_LOG_FLAGS attr support").
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Fixes commit 735cffe5d800 ("net_sched: Introduce skbmod action")
Not used by iproute2 but maybe in future.
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When we unload the ep93xx_eth, whether we have opened the network
interface or not, we will either hit a kernel paging request error, or a
simple NULL pointer de-reference because:

- if ep93xx_open has been called, we have created a valid DMA mapping
  for ep->descs, when we call ep93xx_stop, we also call
  ep93xx_free_buffers, ep->descs now has a stale value

- if ep93xx_open has not been called, we have a NULL pointer for
  ep->descs, so performing any operation against that address just won't
  work

Fix this by adding a NULL pointer check for ep->descs which means that
ep93xx_free_buffers() was able to successfully tear down the descriptors
and free the DMA cookie as well.

Fixes: 1d22e05d ("[PATCH] Cirrus Logic ep93xx ethernet driver")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Yuval Mintz says:

====================
bnx2x: fixes series

Two unrelated fixes for bnx2x - the first one is nice-to-have,
while the other fixes fatal behaviour in older adapters.

Please consider applying them to `net'.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Only the 578xx adapters are capable of configuring UDP ports for
the purpose of tunnelling - doing the same on 577xx might lead to
a firmware assertion.
We're already not claiming support for any related feature for such
devices, but we also need to prevent the configuration of the UDP
ports to the device in this case.

Fixes: f34fa14c ("bnx2x: Add vxlan RSS support")
Reported-by: Anikina Anna <anikina@gmail.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Until interface is up [and assuming ringparams weren't explicitly
configured] when queried for the size of its rings bnx2x would
claim they're the maximal size by default.
That is incorrect as by default the maximal number of buffers would
be equally divided between the various rx rings.

This prevents the user from actually setting the number of elements
on each rx ring to be of maximal size prior to transitioning the
interface into up state.

To fix this, make a rough estimation about the number of buffers.
It wouldn't always be accurate, but it would be much better than
current estimation and would allow users to increase number of
buffers during early initialization of the interface.
Reported-by: Seymour, Shane <shane.seymour@hpe.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In function hfc4s8s_probe(), the value of return variable err should be
negative on failures. However, when the call to request_region() returns
NULL, the value of err is 0. This patch fixes the bug, assigning
"-EBUSY" to err on the path that request_region() fails.

Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=188931Signed-off-by: Pan Bian <bianpan2016@163.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Macro BNX2X_ALLOC_AND_SET(arr, lbl, func) calls kmalloc() to allocate
memory, and jumps to label "lbl" if the allocation fails. Label "lbl"
first cleans memory and then returns variable rc. Before calling the
macro, the value of variable rc is 0. Because 0 means no error, the
callers of bnx2x_init_firmware() may be misled. This patch fixes the bug,
assigning "-ENOMEM" to rc before calling macro NX2X_ALLOC_AND_SET().

Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=189141Signed-off-by: Pan Bian <bianpan2016@163.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When calling dma_mapping_error(), the value of return variable rc is 0.
And when the call returns an unexpected value, rc is not set to a
negative errno. Thus, it will return 0 on the error path, and its
callers cannot detect the bug. This patch fixes the bug, assigning
"-ENOMEM" to err.

Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=189041Signed-off-by: Pan Bian <bianpan2016@163.com>
Acked-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

It returns variable "error" when ioremap_nocache() returns a NULL
pointer. The value of "error" is 0 then, which will mislead the callers
to believe that there is no error. This patch fixes the bug, returning
"-ENOMEM".

Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=189021Signed-off-by: Pan Bian <bianpan2016@163.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When the calls to kzalloc() fail, the value of return variable ret may
be 0. 0 means success in this context. This patch fixes the bug,
assigning "-ENOMEM" to ret before calling kzalloc().

Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=188971Signed-off-by: Pan Bian <bianpan2016@163.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The check of the return value of sock_register() is ineffective.
"if(!err)" seems to be a typo. It is better to propagate the error code
to the callers of caif_sktinit_module(). This patch removes the check
statment and directly returns the result of sock_register().

Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=188751Signed-off-by: Pan Bian <bianpan2016@163.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Prior to commit c0371da6 ("put iov_iter into msghdr") in v3.19, there
was no check that the iovec contained enough bytes for an ICMP header,
and the read loop would walk across neighboring stack contents. Since the
iov_iter conversion, bad arguments are noticed, but the returned error is
EFAULT. Returning EINVAL is a clearer error and also solves the problem
prior to v3.19.

This was found using trinity with KASAN on v3.18:

BUG: KASAN: stack-out-of-bounds in memcpy_fromiovec+0x60/0x114 at addr ffffffc071077da0
Read of size 8 by task trinity-c2/9623
page:ffffffbe034b9a08 count:0 mapcount:0 mapping:          (null) index:0x0
flags: 0x0()
page dumped because: kasan: bad access detected
CPU: 0 PID: 9623 Comm: trinity-c2 Tainted: G    BU         3.18.0-dirty #15
Hardware name: Google Tegra210 Smaug Rev 1,3+ (DT)
Call trace:
[<ffffffc000209c98>] dump_backtrace+0x0/0x1ac arch/arm64/kernel/traps.c:90
[<ffffffc000209e54>] show_stack+0x10/0x1c arch/arm64/kernel/traps.c:171
[<     inline     >] __dump_stack lib/dump_stack.c:15
[<ffffffc000f18dc4>] dump_stack+0x7c/0xd0 lib/dump_stack.c:50
[<     inline     >] print_address_description mm/kasan/report.c:147
[<     inline     >] kasan_report_error mm/kasan/report.c:236
[<ffffffc000373dcc>] kasan_report+0x380/0x4b8 mm/kasan/report.c:259
[<     inline     >] check_memory_region mm/kasan/kasan.c:264
[<ffffffc00037352c>] __asan_load8+0x20/0x70 mm/kasan/kasan.c:507
[<ffffffc0005b9624>] memcpy_fromiovec+0x5c/0x114 lib/iovec.c:15
[<     inline     >] memcpy_from_msg include/linux/skbuff.h:2667
[<ffffffc000ddeba0>] ping_common_sendmsg+0x50/0x108 net/ipv4/ping.c:674
[<ffffffc000dded30>] ping_v4_sendmsg+0xd8/0x698 net/ipv4/ping.c:714
[<ffffffc000dc91dc>] inet_sendmsg+0xe0/0x12c net/ipv4/af_inet.c:749
[<     inline     >] __sock_sendmsg_nosec net/socket.c:624
[<     inline     >] __sock_sendmsg net/socket.c:632
[<ffffffc000cab61c>] sock_sendmsg+0x124/0x164 net/socket.c:643
[<     inline     >] SYSC_sendto net/socket.c:1797
[<ffffffc000cad270>] SyS_sendto+0x178/0x1d8 net/socket.c:1761

CVE-2016-8399
Reported-by: Qidan He <i@flanker017.me>
Fixes: c319b4d7 ("net: ipv4: add IPPROTO_ICMP socket kind")
Cc: stable@vger.kernel.org
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pull powerpc fixes from Michael Ellerman:
 "Four fixes, the first for code we merged this cycle and three that are
  also going to stable:

   - On 64-bit Book3E we were not placing the .text section where we
     said we would in the asm.

   - We broke building the boot wrapper on some 32-bit toolchains.

   - Lazy icache flushing was broken on pre-POWER5 machines.

   - One of the error paths in our EEH code would lead to a deadlock.

  Thanks to: Andrew Donnellan, Ben Hutchings, Benjamin Herrenschmidt,
  Nicholas Piggin"

* tag 'powerpc-4.9-7' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
  powerpc/64: Fix placement of .text to be immediately following .head.text
  powerpc/eeh: Fix deadlock when PE frozen state can't be cleared
  powerpc/mm: Fix lazy icache flush on pre-POWER5
  powerpc/boot: Fix build failure in 32-bit boot wrapper