Fix kconfig warnings:

PTP_1588_CLOCK selects NET_PTP_CLASSIFY, which depends on NET,
so PTP_1588_CLOCK should also depend on NET.

PTP_1588_CLOCK_PCH selects PTP_1588_CLOCK so the former should
depend on NET.

warning: (IXP4XX_ETH && PTP_1588_CLOCK) selects NET_PTP_CLASSIFY which has unmet direct dependencies (NET)

warning: (SFC && TILE_NET && BFIN_MAC_USE_HWSTAMP && TIGON3 && FEC && E1000E && IGB && IXGBE && I40E && MLX4_EN && SXGBE_ETH && STMMAC_ETH && TI_CPTS && PTP_1588_CLOCK_GIANFAR && PTP_1588_CLOCK_IXP46X && DP83640_PHY && PTP_1588_CLOCK_PCH) selects PTP_1588_CLOCK which has unmet direct dependencies (NET)
[This warning is caused by the new 'depends on NET' in PTP_1588_CLOCK.]
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

John W. Linville says:

====================
pull request: wireless 2014-05-08

This one is all from Johannes:

"Here are a few small fixes for the current cycle: radiotap TX flags were
wrong (fix by Bob), Chun-Yeow fixes an SMPS issue with mesh interfaces,
Eliad fixes a locking bug and a cfg80211 state problem and finally
Henning sent me a fix for IBSS rate information."

Please let me know if there are problems!
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

In the cas_lock_tx function we acquire multiple locks in a loop and
need to use nested lock annotation to prevent lockdep warnings.
Reported-by: Meelis Roos <mroos@linux.ee>
Signed-off-by: Emil Goode <emilgoode@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Commit 91ebb928b "bnx2x: Add support for Multi-Function UNDI" contains a bug
which prevent the emptying of the device's Rx buffers before reset.
As a result, on new boards it is likely HW will reach some fatal assertion
once its interfaces load after UNDI was previously loaded.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Johan Hovold says:

====================
net: cpsw and mdio-gpio fixes for v3.15-final

These patches against v3.15-rc4 fix a few issues in the cpsw and
mdio-gpio drivers.

Resend with proper stable CC (git send-email still fails to parse the

Sorry about the noise.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Add missing of_node_put to avoid kref leak.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Fix null-pointer dereference at probe when the mdio platform device is
missing (e.g. when it has been disabled in DT).

Cc: stable <stable@vger.kernel.org>	# v3.8
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This reverts commit f8d56d8f ("net:
 eth: cpsw: Correctly attach to GPIO bitbang MDIO driver").

Fix potential null-pointer dereference at probe if the mdio-gpio device
has not been successfully probed yet.

The offending commit is plain wrong for a number of reasons. First of
all it accesses internal driver data of an unrelated device. Neither
does it check that the data is non-null (which it is in case the device
has not been probed yet).

Furthermore, the decision on whether to treat any driver data according
to the mdio-gpio driver's internals is made based on the node name. But
the name is not compared against "mdio" which is the normal name for the
node, but rather against "gpio" which the node does not have to be named
(and shouldn't be according to the binding documentation). [ If this
hack is to be kept out-of-tree it should at least be matching against
the compatible property. ]

Cc: Stefan Roese <sr@denx.de>
Cc: stable <stable@vger.kernel.org>	# v3.14
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Use a sane default bus id (rather than -ENODEV) and print a warning when
the bus alias id is missing.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Fix aliases syntax in device-tree binding example to avoid
copy-paste errors (the alias would be dropped silently).
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This driver maps 802.1q VLANs to MBIM sessions. The mapping is based on
a bogus assumption that all tagged frames will use the acceleration API
because we enable NETIF_F_HW_VLAN_CTAG_TX. This fails for e.g. frames
tagged in userspace using packet sockets. Such frames will erroneously
be considered as untagged and silently dropped based on not being IP.

Fix by falling back to looking into the ethernet header for a tag if no
accelerated tag was found.

Fixes: a82c7ce5 ("net: cdc_ncm: map MBIM IPS SessionID to VLAN ID")
Cc: Greg Suarez <gsuarez@smithmicro.com>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pablo Neira Ayuso says:

====================
Netfilter fixes for net

The following batch contains netfilter fixes for your net tree, they are:

1) Fix use after free in nfnetlink when sending a batch for some
   unsupported subsystem, from Denys Fedoryshchenko.

2) Skip autoload of the nat module if no binding is specified via
   ctnetlink, from Florian Westphal.

3) Set local_df after netfilter defragmentation to avoid a bogus ICMP
   fragmentation needed in the forwarding path, also from Florian.

4) Fix potential user after free in ip6_route_me_harder() when returning
   the error code to the upper layers, from Sergey Popovich.

5) Skip possible bogus ICMP time exceeded emitted from the router (not
   valid according to RFC) if conntrack zones are used, from Vasily Averin.

6) Fix fragment handling when nf_defrag_ipv4 is loaded but nf_conntrack
   is not present, also from Vasily.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

This driver adds support for EtherCAT master module located on CCAT
FPGA found on Beckhoff CX series industrial PCs. The driver exposes
EtherCAT master as an ethernet interface.

EtherCAT is a fieldbus protocol defined on top of ethernet and Beckhoff
CX5020 PCs come with built-in EtherCAT master module located on a FPGA,
which in turn is connected to a PCI bus.
Signed-off-by: Dariusz Marcinkiewicz <reksio@newterm.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>

Similarly, when CONFIG_SYSCTL is not set, ping_group_range should still
work, just that no one can change it. Therefore we should move it out of
sysctl_net_ipv4.c. And, it should not share the same seqlock with
ip_local_port_range.

BTW, rename it to ->ping_group_range instead.

Cc: David S. Miller <davem@davemloft.net>
Cc: Francois Romieu <romieu@fr.zoreil.com>
Reported-by: Stefan de Konink <stefan@konink.de>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When CONFIG_SYSCTL is not set, ip_local_port_range should still work,
just that no one can change it. Therefore we should move it out of sysctl_inet.c.
Also, rename it to ->ip_local_ports instead.

Cc: David S. Miller <davem@davemloft.net>
Cc: Francois Romieu <romieu@fr.zoreil.com>
Reported-by: Stefan de Konink <stefan@konink.de>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Dst is released one line before we access it again with dst->error.

Fixes: 58e35d14 netfilter: ipv6: propagate routing errors from
ip6_route_me_harder()
Signed-off-by: Sergey Popovich <popovich_sergei@mail.ru>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>

Merge branch 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless into for-davem

If CONFIG_OF is not set, make of_mdiobus_register() call
mdiobus_register() instead of returning -ENOSYS.

This way, we can just call of_mdiobus_register() from all DT-enabled
drivers to handle the compat cases.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Suggested-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Increment fib_info_cnt in fib_create_info() right after successfuly
alllocating fib_info structure, overwise fib_metrics allocation failure
leads to fib_info_cnt incorrectly decremented in free_fib_info(), called
on error path from fib_create_info().
Signed-off-by: Sergey Popovich <popovich_sergei@mail.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>

Rajesh Borundia says:

====================
qlcnic: Bug fixes.

This patch series contain following bug fixes.

* Fix panic where driver was accessing un-initialized crb_intr_mask
  in non Multi-Tx queue mode while dumping TX queue.
* Do not set netdev->real_num_tx_queues directly from driver instead
  use kernel defined netif_set_real_num_tx_queues() API. Also notify
  stack about change in number of Rx queues.

Please apply this series to net.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Do not set netdev->real_num_tx_queues directly,
let netif_set_real_num_tx_queues() take care of it.
Do not overwrite netdev->num_tx_queues everytime when driver
changes its Tx ring size through ethtool -L and also notify
stack to update number of Rx queues.
Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

o In case of non-multi TX queue mode driver does not initialize "crb_intr_mask" pointer
  and driver was accessing that un-initialized pointer while dumping TX queue.
  So dump "crb_intr_mask" only when it is initilaized.
Signed-off-by: Manish Chopra <manish.chopra@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The jme driver forgot to check the return status from pci_map_page in its tx
path, causing a dma api warning on unmap.  Easy fix, just do the check and
augment the tx path to tell the stack that the driver is busy so we re-queue the
frame.
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
CC: Guo-Fu Tseng <cooldavid@cooldavid.org>
CC: "David S. Miller" <davem@davemloft.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

Florian Westphal says:

====================
net: ip: push gso skb forwarding handling down the stack

Turns out doing the segmentation in forwarding was not a bright idea,
there are corner-cases where this has unintended side-effects.

This patch pushes the segmentation downwards.

After this, netif_skb_dev_features() function can be removed
again, it was only added to fetch the features of the output device,
we can just use skb->dev after the pushdown.

Tested with following setup:

host -> kvm_router  -> kvm_host
  mtu 1500        mtu1280

- 'host' has route to kvm_host with locked mtu of 1500
- gso/gro enabled on all interfaces

Did tests with all of following combinations:
- netfilter conntrack off and on on kvm_router
- virtio-net and e1000 driver on kvm_router
- tcp and udp bulk xmit from host to kvm_host

for tcp, I added TCPMSS mangling on kvm_host to make it lie about tcp mss.

Also added a dummy '-t mangle -A POSTROUTING -p udp -f'
rule to make sure no udp fragments are seen in the 'conntrack on'
and 'virtio-net' case.

Also checked (with ping -M do -s 1400)' that it still sends the wanted
icmp error message when size exceeds 1280.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

This reverts commit d2069403,
there are no more callers.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

Doing the segmentation in the forward path has one major drawback:

When using virtio, we may process gso udp packets coming
from host network stack.  In that case, netfilter POSTROUTING
will see one packet with udp header followed by multiple ip
fragments.

Delay the segmentation and do it after POSTROUTING invocation
to avoid this.

Fixes: fe6cc55f ("net: ip, ipv6: handle gso skbs in forwarding path")
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

If conntrack defragments incoming ipv6 frags it stores largest original
frag size in ip6cb and sets ->local_df.

We must thus first test the largest original frag size vs. mtu, and not
vice versa.

Without this patch PKTTOOBIG is still generated in ip6_fragment() later
in the stack, but

1) IPSTATS_MIB_INTOOBIGERRORS won't increment
2) packet did (needlessly) traverse netfilter postrouting hook.

Fixes: fe6cc55f ("net: ip, ipv6: handle gso skbs in forwarding path")
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

local_df means 'ignore DF bit if set', so if its set we're
allowed to perform ip fragmentation.

This wasn't noticed earlier because the output path also drops such skbs
(and emits needed icmp error) and because netfilter ip defrag did not
set local_df until couple of days ago.

Only difference is that DF-packets-larger-than MTU now discarded
earlier (f.e. we avoid pointless netfilter postrouting trip).

While at it, drop the repeated test ip_exceeds_mtu, checking it once
is enough...

Fixes: fe6cc55f ("net: ip, ipv6: handle gso skbs in forwarding path")
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

Fixes this warning introduced by commit 5b8f15f7
("net: cdc_mbim: handle IPv6 Neigbor Solicitations"):

===============================
[ INFO: suspicious RCU usage. ]
3.15.0-rc3 #213 Tainted: G        W  O
-------------------------------
net/8021q/vlan_core.c:69 suspicious rcu_dereference_check() usage!

other info that might help us debug this:

rcu_scheduler_active = 1, debug_locks = 1
no locks held by ksoftirqd/0/3.

stack backtrace:
CPU: 0 PID: 3 Comm: ksoftirqd/0 Tainted: G        W  O  3.15.0-rc3 #213
Hardware name: LENOVO 2776LEG/2776LEG, BIOS 6EET55WW (3.15 ) 12/19/2011
 0000000000000001 ffff880232533bf0 ffffffff813a5ee6 0000000000000006
 ffff880232530090 ffff880232533c20 ffffffff81076b94 0000000000000081
 0000000000000000 ffff8802085ac000 ffff88007fc8ea00 ffff880232533c50
Call Trace:
 [<ffffffff813a5ee6>] dump_stack+0x4e/0x68
 [<ffffffff81076b94>] lockdep_rcu_suspicious+0xfa/0x103
 [<ffffffff813978a6>] __vlan_find_dev_deep+0x54/0x94
 [<ffffffffa04a1938>] cdc_mbim_rx_fixup+0x379/0x66a [cdc_mbim]
 [<ffffffff813ab76f>] ? _raw_spin_unlock_irqrestore+0x3a/0x49
 [<ffffffff81079671>] ? trace_hardirqs_on_caller+0x192/0x1a1
 [<ffffffffa059bd10>] usbnet_bh+0x59/0x287 [usbnet]
 [<ffffffff8104067d>] tasklet_action+0xbb/0xcd
 [<ffffffff81040057>] __do_softirq+0x14c/0x30d
 [<ffffffff81040237>] run_ksoftirqd+0x1f/0x50
 [<ffffffff8105f13e>] smpboot_thread_fn+0x172/0x18e
 [<ffffffff8105efcc>] ? SyS_setgroups+0xdf/0xdf
 [<ffffffff810594b0>] kthread+0xb5/0xbd
 [<ffffffff813a84b1>] ? __wait_for_common+0x13b/0x170
 [<ffffffff810593fb>] ? __kthread_parkme+0x5c/0x5c
 [<ffffffff813b147c>] ret_from_fork+0x7c/0xb0
 [<ffffffff810593fb>] ? __kthread_parkme+0x5c/0x5c

Fixes: 5b8f15f7 ("net: cdc_mbim: handle IPv6 Neigbor Solicitations")
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pull networking fixes from David Miller:

 1) e1000e computes header length incorrectly wrt vlans, fix from Vlad
    Yasevich.

 2) ns_capable() check in sock_diag netlink code, from Andrew
    Lutomirski.

 3) Fix invalid queue pairs handling in virtio_net, from Amos Kong.

 4) Checksum offloading busted in sxgbe driver due to incorrect
    descriptor layout, fix from Byungho An.

 5) Fix build failure with SMC_DEBUG set to 2 or larger, from Zi Shen
    Lim.

 6) Fix uninitialized A and X registers in BPF interpreter, from Alexei
    Starovoitov.

 7) Fix arch dependencies of candence driver.

 8) Fix netlink capabilities checking tree-wide, from Eric W Biederman.

 9) Don't dump IFLA_VF_PORTS if netlink request didn't ask for it in
    IFLA_EXT_MASK, from David Gibson.

10) IPV6 FIB dump restart doesn't handle table changes that happen
    meanwhile, causing the code to loop forever or emit dups, fix from
    Kumar Sandararajan.

11) Memory leak on VF removal in bnx2x, from Yuval Mintz.

12) Bug fixes for new Altera TSE driver from Vince Bridgers.

13) Fix route lookup key in SCTP, from Xugeng Zhang.

14) Use BH blocking spinlocks in SLIP, as per a similar fix to CAN/SLCAN
    driver.  From Oliver Hartkopp.

15) TCP doesn't bump retransmit counters in some code paths, fix from
    Eric Dumazet.

16) Clamp delayed_ack in tcp_cubic to prevent theoretical divides by
    zero.  Fix from Liu Yu.

17) Fix locking imbalance in error paths of HHF packet scheduler, from
    John Fastabend.

18) Properly reference the transport module when vsock_core_init() runs,
    from Andy King.

19) Fix buffer overflow in cdc_ncm driver, from Bjørn Mork.

20) IP_ECN_decapsulate() doesn't see a correct SKB network header in
    ip_tunnel_rcv(), fix from Ying Cai.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (132 commits)
  net: macb: Fix race between HW and driver
  net: macb: Remove 'unlikely' optimization
  net: macb: Re-enable RX interrupt only when RX is done
  net: macb: Clear interrupt flags
  net: macb: Pass same size to DMA_UNMAP as used for DMA_MAP
  ip_tunnel: Set network header properly for IP_ECN_decapsulate()
  e1000e: Restrict MDIO Slow Mode workaround to relevant parts
  e1000e: Fix issue with link flap on 82579
  e1000e: Expand workaround for 10Mb HD throughput bug
  e1000e: Workaround for dropped packets in Gig/100 speeds on 82579
  net/mlx4_core: Don't issue PCIe speed/width checks for VFs
  net/mlx4_core: Load the Eth driver first
  net/mlx4_core: Fix slave id computation for single port VF
  net/mlx4_core: Adjust port number in qp_attach wrapper when detaching
  net: cdc_ncm: fix buffer overflow
  Altera TSE: ALTERA_TSE should depend on HAS_DMA
  vsock: Make transport the proto owner
  net: sched: lock imbalance in hhf qdisc
  net: mvmdio: Check for a valid interrupt instead of an error
  net phy: Check for aneg completion before setting state to PHY_RUNNING
  ...

Pull USB fixes from Greg KH:
 "Here are some small fixes and device ids for 3.15-rc4.

  All have been in linux-next just fine"

* tag 'usb-3.15-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
  USB: Nokia 5300 should be treated as unusual dev
  USB: Nokia 305 should be treated as unusual dev
  fsl-usb: do not test for PHY_CLK_VALID bit on controller version 1.6
  usb: storage: shuttle_usbat: fix discs being detected twice
  usb: qcserial: add a number of Dell devices
  USB: OHCI: fix problem with global suspend on ATI controllers
  usb: gadget: at91-udc: fix irq and iomem resource retrieval
  usb: phy: fsm: change "|" to "||" for condition OTG_STATE_A_WAIT_BCON at statemachine
  usb: phy: fsm: update OTG HNP state transition

Pull tty/serial fixes from Greg KH:
 "Here are some tty and serial driver fixes for things reported
  recently"

* tag 'tty-3.15-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
  tty: Fix lockless tty buffer race
  Revert "tty: Fix race condition between __tty_buffer_request_room and flush_to_ldisc"
  drivers/tty/hvc: don't free hvc_console_setup after init
  n_tty: Fix n_tty_write crash when echoing in raw mode
  tty: serial: 8250_core.c Bug fix for Exar chips.

Pull staging / iio fixes from Greg KH:
 "Here are some small IIO driver fixes for 3.15-rc4 that resolve some
  reported issues"

* tag 'staging-3.15-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
  iio: adc: Nothing in ADC should be a bool CONFIG
  iio: exynos_adc: use indio_dev->dev structure to handle child nodes
  iio:imu:mpu6050: Fixed segfault in Invensens MPU driver due to null dereference
  staging:iio:ad2s1200 fix missing parenthesis in a for statment.

Pull Xtensa fixes from Chris Zankel:
 - Fixes allmodconfig, allnoconfig builds
 - Adds highmem support
 - Enables build-time exception table sorting.

* tag 'xtensa-next-20140503' of git://github.com/czankel/xtensa-linux:
  xtensa: ISS: don't depend on CONFIG_TTY
  xtensa: xt2000: drop redundant sysmem initialization
  xtensa: add support for KC705
  xtensa: xtfpga: introduce SoC I/O bus
  xtensa: add HIGHMEM support
  xtensa: optimize local_flush_tlb_kernel_range
  xtensa: dump sysmem from the bootmem_init
  xtensa: handle memmap kernel option
  xtensa: keep sysmem banks ordered in mem_reserve
  xtensa: keep sysmem banks ordered in add_sysmem_bank
  xtensa: split bootparam and kernel meminfo
  xtensa: enable sorting extable at build time
  xtensa: export __{invalidate,flush}_dcache_range
  xtensa: Export __invalidate_icache_range

Pull Ceph fixes from Sage Weil:
 "First, there is a critical fix for the new primary-affinity function
  that went into -rc1.

  The second batch of patches from Zheng fix a range of problems with
  directory fragmentation, readdir, and a few odds and ends for cephfs"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/sage/ceph-client:
  ceph: reserve caps for file layout/lock MDS requests
  ceph: avoid releasing caps that are being used
  ceph: clear directory's completeness when creating file
  libceph: fix non-default values check in apply_primary_affinity()
  ceph: use fpos_cmp() to compare dentry positions
  ceph: check directory's completeness before emitting directory entry

Under "heavy" RX load, the driver cannot handle the descriptors fast
enough. In detail, when a descriptor is consumed, its used flag is
cleared and once the RX budget is consumed all descriptors with a
cleared used flag are prepared to receive more data. Under load though,
the HW may constantly receive more data and use those descriptors with a
cleared used flag before they are actually prepared for next usage.

The head and tail pointers into the RX-ring should always be valid and
we can omit clearing and checking of the used flag.
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Coverage data suggests that the unlikely case of receiving data while
the receive handler is running may not be that unlikely.
Coverage data after running iperf for a while:
    91320:  891:	work_done = bp->macbgem_ops.mog_rx(bp, budget);
    91320:  892:	if (work_done < budget) {
     2362:  893:		napi_complete(napi);
        -:  894:
        -:  895:		/* Packets received while interrupts were disabled */
     4724:  896:		status = macb_readl(bp, RSR);
     2362:  897:		if (unlikely(status)) {
      762:  898:			if (bp->caps & MACB_CAPS_ISR_CLEAR_ON_WRITE)
      762:  899:				macb_writel(bp, ISR, MACB_BIT(RCOMP));
        -:  900:			napi_reschedule(napi);
        -:  901:		} else {
     1600:  902:			macb_writel(bp, IER, MACB_RX_INT_FLAGS);
        -:  903:		}
        -:  904:	}
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When data is received during the driver processing received data the
NAPI is re-scheduled. In that case the RX interrupt should not be
re-enabled.
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

A few interrupt flags were not cleared in the ISR, resulting in a sytem
trapped in the ISR in cases one of those interrupts occurred. Clear all
flags to avoid such situations.
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>