This patch modifies when and where PTP registers and data are set. Previously
a work-around was used inside cyclecounter_start in order to reset some of the
time registers. This patch creates a new ixgbe_ptp_reset specifically for this
purpose. The cyclecounter configuration has trimmed down to only modify what
is necessary. Due to hardware conditions after probe and before open, PTP init
has now moved into the ixgbe_open call. This allows the ptp device name in the
sysfs to be the ethernet device name instead of the MAC address.

The cyclecounter check flag is renamed to PTP_ENABLED and is used to prevent
PTP init from happening when PTP has not been enabled.

CC: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch adds a subdevice id for new 82599 device. The define is needed
to allow enabling WOL support.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

This change adds support for DCB and SR-IOV from the VF.  With this change
in place the VF will correctly use a traffic class other than 0 in the case
that the PF is configured with the default user priority belonging to a
traffic class other than 0.

Cc: Greg Rose <gregory.v.rose@intel.com>
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

This change switches on the last few bits for us enabling version 1.1 VF
support in the PF.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Tested-by: Robert Garrett <RobertX.Garrett@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch addresses several issues in regards to the combination of DCB
and SR-IOV. Specifically it allows us to send information to the VF on
which queues it should be using.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

It is necessary to track the default user priority in the PF so that we can
force it upon the VFs.  The motivation behind this is to keep the VFs from
getting access to user priorities meant for things like storage.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

This change adds support for IPv6 and UDP to ixgbe_get_headlen. The
advantage to this is that we can now handle ipv4/UDP, ipv6/TCP, and
ipv6/UDP with a single memcpy instead of having to do them in multiple
pskb_may_pull calls.

A quick bit of testing shows that we increase throughput for a single
session of netperf from 8800Mpbs to about 9300Mpbs in the case of ipv6/TCP.
As such overall ipv6 performance should improve with this change.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Stephen Ko  <stephen.s.ko@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

A small host typically needs ~10 fib_info structures, so create initial
hash table with 16 slots instead of only one. This removes potential
false sharing and reallocs/rehashes (1->2->4->8->16)
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

SIOCINQ can use the lock_sock_fast() version to avoid double acquisition
of socket lock.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

RFC 5961 5.2 [Blind Data Injection Attack].[Mitigation]

  All TCP stacks MAY implement the following mitigation.  TCP stacks
  that implement this mitigation MUST add an additional input check to
  any incoming segment.  The ACK value is considered acceptable only if
  it is in the range of ((SND.UNA - MAX.SND.WND) <= SEG.ACK <=
  SND.NXT).  All incoming segments whose ACK value doesn't satisfy the
  above condition MUST be discarded and an ACK sent back.

Move tcp_send_challenge_ack() before tcp_ack() to avoid a forward
declaration.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Neal Cardwell <ncardwell@google.com>
Cc: Yuchung Cheng <ycheng@google.com>
Cc: Jerry Chu <hkchu@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

ns_to_ktime() seems better than ktime_set() + ktime_add_ns()
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Padmanabh Ratnakar <padmanabh.ratnakar@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Padmanabh Ratnakar <padmanabh.ratnakar@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

FW flash layout on Skyhawk-R is different from BE3-R.
Hence the code needs to be fixed to flash FW on Skyhawk-R.
Also cleaning up code in BE3-R flashing function.
Signed-off-by: Vasundhara Volam <vasundhara.volam@emulex.com>
Signed-off-by: Padmanabh Ratnakar <padmanabh.ratnakar@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

be_shutdown is enabling wake-on-lan by calling be_setup_wol.
Emulex adapter do not support wake-on-lan in S5 state.
Signed-off-by: Vasundhara Volam <vasundhara.volam@emulex.com>
Signed-off-by: Padmanabh Ratnakar <padmanabh.ratnakar@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

PF driver should enable VF so that VF goes to ready state in
new Lancer FW.
Signed-off-by: Padmanabh Ratnakar <padmanabh.ratnakar@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

During PCI EEH, driver waits for all functions in the card.
Wait is needed only once per card. Fix is to wait only for the
first PCI function.
Signed-off-by: Padmanabh Ratnakar <padmanabh.ratnakar@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

During recovery from a FW error, destroy queue operation may fail.
Queue should be marked as destroyed so that recovery code can recreate
the queue. Also fix queue created state not getting checked at one instance.
Signed-off-by: Padmanabh Ratnakar <padmanabh.ratnakar@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Return default values for fields for which VFs dont have privilege to get the
required information from FW.
Signed-off-by: Padmanabh Ratnakar <padmanabh.ratnakar@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

VF does not have privileges to execute many commands. When VFs try
to execute those commands there are unnecessary error messages.
Fix this by executing only those commands for which VF has privilege.
Signed-off-by: Padmanabh Ratnakar <padmanabh.ratnakar@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Allow adding VLANs for Lancer VF.
VLAN ID 0 should not be added to list of VLANs sent to FW.
Signed-off-by: Padmanabh Ratnakar <padmanabh.ratnakar@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

After FW error, driver should wait for NO_RESOURCE error to disappear before
proceeding with recovery.
Signed-off-by: Padmanabh Ratnakar <padmanabh.ratnakar@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

For changing MAC of VF from PF, delete MAC operation needs to be done before
assigning new MAC. Also in ndo_set_mac_address operation avoid delete MAC if
it has been already deleted by PF.
Signed-off-by: Padmanabh Ratnakar <padmanabh.ratnakar@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Use Lancer specific command to set QoS for VF.
Signed-off-by: Padmanabh Ratnakar <padmanabh.ratnakar@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Driver assumes FW resource counts and capabilities while creating queues and
using functionality like RSS. This causes driver load to fail in FW configs
where resources and capabilities are reduced. Fix this by querying FW
configuration during probe and using resources and capabilities accordingly.
Signed-off-by: Padmanabh Ratnakar <padmanabh.ratnakar@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch removes double assignment of err to -EINVAL in dev_change_net_namespace().
Signed-off-by: Rami Rosen <ramirose@gmail.com>
Acked-by: Serge E. Hallyn <serge.hallyn@ubuntu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The SO_BINDTODEVICE option is the only SOL_SOCKET one that can be set, but
cannot be get via sockopt API. The only way we can find the device id a
socket is bound to is via sock-diag interface. But the diag works only on
hashed sockets, while the opt in question can be set for yet unhashed one.

That said, in order to know what device a socket is bound to (we do want
to know this in checkpoint-restore project) I propose to make this option
getsockopt-able and report the respective device index.

Another solution to the problem might be to teach the sock-diag reporting
info on unhashed sockets. Should I go this way instead?
Signed-off-by: Pavel Emelyanov <xemul@parallels.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The struct sock *other one seem to be unused. Grep and make do not object.
Signed-off-by: Pavel Emelyanov <xemul@parallels.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Use the standard test for a non-zero ipv6 address.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Checked with Windows networking team, there is only one RNDIS message
in each netvsc packet.
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Reviewed-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Jeff Kirsher says:

====================
This series contains updates to ixgbe and igb.

Alexander Duyck (13):
  ixgbe: Initialize q_vector cpu and affinity masks correctly
  ixgbe: Enable jumbo frames support w/ SR-IOV
  ixgbe: Move message handling routines into their own functions
  ixgbe: Add mailbox API version negotiation support to ixgbe PF
  igb: Split Rx timestamping into two separate functions
  igb: Do not use header split, instead receive all frames into a
    single buffer
  igb: Combine post-processing of skb into a single function
  igb: Map entire page and sync half instead of mapping and unmapping
    half pages
  igb: Move rx_buffer related code in Rx cleanup path into separate
    function
  igb: Lock buffer size at 2K even on systems with larger pages
  igb: Combine q_vector and ring allocation into a single function
  igb: Move the calls to set the Tx and Rx queues into igb_open
  igb: Split igb_update_dca into separate Tx and Rx functions

Tushar Dave (1):
  igb: Correcting and improving small packet check and padding
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Joachim Eastwood says;

====================
This patch series prepares the old at91_ether driver for code sharing
with the macb driver. The hardware is similar except for DMA TX/RX, so
its not quite clear if it is practical to support both in one
driver. But stuff like MDIO and statistics should be possible to
share.

Patch 1 adds some register defines and bits that is only found on
RM9200.

Patch 2-4 uses the register defines and access functions from the macb
header. These can be squashed if it cause too much churn.

Patch 5 merges the private at91_ether struct with the private macb
struct. This makes it easier to later share code with the macb. The
private macb struct becomes quite large, but most at91_ether specific
members are removed in later patches.

Patch 8 make macb compile when we select at91_ether. Is this approach
okey?

Patch 9 makes use of MDIO code from macb. This rips out the private
phy handling code in at91_ether. One thing that is lost is the
interrupt support for phy. But this should easy to add to macb which
will then benefit both drivers.

Patch 10 makes use of the macb_set_rx_mode from macb.

Patch 11-12 makes at91_ether share the rx dma struct members from
macb. Patch also moves the rx buffer allocation into netdev open and
dealloc into netdev close.

Last patch remove the now unused rm9200 emac header from include/mach.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

This file is unused after at91_ether was converted to use macb.h
Signed-off-by: Joachim Eastwood <manabian@gmail.com>

Signed-off-by: Joachim Eastwood <manabian@gmail.com>

This patch does two things:
* Use macb struct members and remove at91_ether ones
* Alloc DMA buffers on netdev start and dealloc on stop
Signed-off-by: Joachim Eastwood <manabian@gmail.com>

Signed-off-by: Joachim Eastwood <manabian@gmail.com>

Signed-off-by: Joachim Eastwood <manabian@gmail.com>

This rips out the at91_ether phy handling and ethtool stuff
and replace it with equivalent stuff from macb.

The only thing lost is the phy irq support from at91_ether,
but this can be added to macb and then benefit all users.
Signed-off-by: Joachim Eastwood <manabian@gmail.com>

Comile macb as well as at91_ether to access exported functions.
Signed-off-by: Joachim Eastwood <manabian@gmail.com>

Export some symbols to start sharing code between
macb and at91_ether drivers.
Signed-off-by: Joachim Eastwood <manabian@gmail.com>