[why]
DP LL CTS1.4 4.3.2.1 test failure.

[how]
The failure is caused by not handling DP link loss
hpd short pusle during set mode. The change is to read link status
before set mode link training. If link is lost, re-verify link caps.
Signed-off-by: Wenjing Liu <Wenjing.Liu@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

[WHY]
Currently, when the VSP infopacket is rebuilt in DM, it is not updated
when being programmed in encoder.

[HOW]
Add new VSP case for update_info_frame
Signed-off-by: SivapiriyanKumarasamy <sivapiriyan.kumarasamy@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Krunoslav Kovac <Krunoslav.Kovac@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

[WHY]
On customer board, there is one pluse (1v , < 1ms) on
DDC_CLK pin when plug / unplug DP cable. Driver will read
it and config DP to HDMI/DVI dongle.

[HOW]
If there is a real dongle, DDC_CLK should be always pull high.
Try to read again to recovery this special case. Retry times = 3.
Need additional 3ms to detect DP passive dongle(3 failures)
Signed-off-by: Paul Hsieh <paul.hsieh@amd.com>
Reviewed-by: Eric Yang <eric.yang2@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

[Why]
Skipping initial link training will result in no verified link cap for
mode enumeration. Some versions of the BIOS seem to have PHY programming
sequence issue as well if initial link training is skipped, resulting in
a softlock in BIOS command table.

[How]
Identify the empty dongle hotplug case, and still do initial link
training.
Signed-off-by: Eric Yang <Eric.Yang2@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

[Why]
In 99% user case, edp will be post by vbios.
In 1% / current case: Lenovo don't light up edp panel in vbios
post stage, vbios won't be lit up. Thus in dal when we init DCN
10 hw, we power up edp, then we start detect_sink, but internal
time is too short, when we detect it, HPD is still low, so we don't
detect the edp, and edp shows black.

[How]
When we init hw, we wait edp HPD to high after power up edp.
Signed-off-by: Dale Zhao <dale.zhao@amd.com>
Reviewed-by: Eric Yang <eric.yang2@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

An earlier change added update of interdependent dlg/ttu params for pipes
not being updated in the current call. The code fails to check if the other
pipes are actually active yet causing an assert.

This change adds a check for surface presence on the pipes before updating
the interdepenednt params.
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Nikola Cornij <Nikola.Cornij@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

[Why]
YCbCr420 packing format uses two chanels for luma, and 1
channel for both chroma component. Our previous implementation
did not account for this and results in every other pixel having
very high luma value, showing greyish color instead of black.

YCbCr444 = <Y1, Cb1, Cr1>; <Y2, Cb2, Cr2> .....
YCbCr420 = <Y1, Y2,  Cb1>; <Y3, Y4,  Cr1> .....

[How]
Program the second channel with the black color value for luma
as well.
Signed-off-by: Eric Yang <Eric.Yang2@amd.com>
Reviewed-by: Hugo Hu <Hugo.Hu@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

[Why]
DC warns when a REG_WAIT takes a while and full-on errors
with stack dump on REG_WAIT timeout.  Most of the time it isn't
a real issue.

[How]
Make DC cool its jets - taking a while is a debug message (because
it is not something that normal users should need to be aware of),
and timeouts are warnings (because it technically shouldn't
happen, but it's not a big deal if it does)
Signed-off-by: David Francis <David.Francis@amd.com>
Reviewed-by: Harry Wentland <Harry.Wentland@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

This is a dual channel format and should be treated like other
video formats
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Eric Bernstein <Eric.Bernstein@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

[Why]
In certain configurations, such as PX configs or some Vega20 parts
DC gets created without connectors.

[How]
Drop the dm_error print when no connectors.
Signed-off-by: Harry Wentland <harry.wentland@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

[Why]
When XGMI is enabled, the DP reference clock needs to be adjusted
according to the XGMI spread spectrum percentage and mode. But first,
we need the ability to fetch this info.

[How]
Within the BIOS parser, Read from vBIOS when XGMI SS info is requested.

In addition, diags build uses include_legacy/atomfirmware.h for the
smu_info_v3_3 table headers. Update that as well.
Signed-off-by: Leo Li <sunpeng.li@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Tony Cheng <Tony.Cheng@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

[Why]
We'll need a way to differentiate Vega 20 in DC

[How]
Add a DCE_VERSION_12_1 enum, which will be returned as the DC version if
the ASIC used is a Vega 20.
Signed-off-by: Leo Li <sunpeng.li@amd.com>
Reviewed-by: David Francis <David.Francis@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

[Why]
When the flip-rate is below the minimum supported variable refresh rate
range for the monitor the front porch wait will timeout and be
frequently misaligned resulting in stuttering and/or flickering.

The FreeSync module can still maintain a smooth and flicker free
image when the monitor has a refresh rate range such that the maximum
refresh > 2 * minimum refresh by utilizing low framerate compensation,
"below the range".

[How]
Hook up the pre-flip and post-flip handlers from the FreeSync module.
These adjust the minimum/maximum vrr range to duplicate frames
when appropriate by tracking flip timestamps.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

[Why]
The visual corruption due to low display clock value observed on some
systems

[How]
There was earlier patch for dspclk:
'drm/amd/display: Raise dispclk value for dce_update_clocks'
Adding +15% workaround also to to dce112_update_clocks
Signed-off-by: Roman Li <Roman.Li@amd.com>
Reviewed-by: Leo Li <Sunpeng.Li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

[Why]
The behavior of drm_atomic_helper_cleanup_planes differs depending on
whether the commit was asynchronous or not. When it's called from
amdgpu_dm_atomic_commit_tail during a typical atomic commit the
plane state has been swapped so it calls cleanup_fb on the old plane
state.

However, in the asynchronous commit codepath the call to
drm_atomic_helper_commit also calls dm_plane_helper_cleanup_fb after
atomic_async_update has been called. Since the plane state is updated
in place and has not been swapped the cleanup_fb call affects the new
plane state.

This results in a use after free for the given sequence:

- Fast update, fb1 pin/ref, fb1 unpin/unref
- Fast update, fb2 pin/ref, fb2 unpin/unref
- Slow update, fb1 pin/ref, fb2 unpin/unref
- Fast update, fb2 pin/ref -> use after free. bug

[How]
Disallow framebuffer changes in the fast path. Since this includes
a NULL framebuffer, this means that only framebuffers that have
been previously pin+ref at least once will be used, preventing a
use after free.

This has a significant throughput reduction for cursor updates where
the framebuffer changes. For most desktop usage this isn't a problem,
but it does introduce performance regressions for two specific IGT
tests:

- cursor-vs-flip-toggle
- cursor-vs-flip-varying-size

Fixes: 2cc751931afc ("drm/amd/display: Add fast path for cursor plane updates")
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Andrey Grodzovsky <andrey.grodzovsky@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

It should not return 0 for error case as '0' is actually
a special value for index.
Signed-off-by: Evan Quan <evan.quan@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

On errors, dma_buf_get returns a negative error code, rather than NULL.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Felix Kuehling <Felix.Kuehling@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

If register value is updating, reset timeout counter.
It improves robustness of SOC15_WAIT_ON_RREG.
Signed-off-by: James Zhu <James.Zhu@amd.com>
Reviewed-by: Leo Liu <leo.liu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Remove bit 31 for scratch2 to indicate the Hardware bug work around is active.
Signed-off-by: James Zhu <James.Zhu@amd.com>
Acked-by: Leo Liu <leo.liu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Scan enc/jpeg fences to init dpg pause new state in begin use.
It will help set dpg mode to desire state actively.
Signed-off-by: James Zhu <James.Zhu@amd.com>
Acked-by: Leo Liu <leo.liu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Always check all vcn ring status during dpg mode stop, it will help
identify which vcn ring may cause the issue.
Signed-off-by: James Zhu <James.Zhu@amd.com>
Acked-by: Leo Liu <leo.liu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

It is a bug fix.
Signed-off-by: James Zhu <James.Zhu@amd.com>
Acked-by: Leo Liu <leo.liu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Under Dynamic Power Gate mode, UVD_STATUS needn't be checked.
Signed-off-by: James Zhu <James.Zhu@amd.com>
Acked-by: Leo Liu <leo.liu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Replace vcn_v1_0_stop with vcn_v1_0_set_powergating_state during suspend,
to keep adev->vcn.cur_state update. It will fix VCN S3 hung issue.
Signed-off-by: James Zhu <James.Zhu@amd.com>
Reviewed-by: Leo Liu <leo.liu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

It indicates a pin/unpin imbalance bug somewhere. While the bug isn't
necessarily in the call chain hitting this, it's at least one part
involved.
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Michel Dänzer <michel.daenzer@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Page queue is supported on Vega20 with SDMA firmware
123 onwards.
Signed-off-by: Evan Quan <evan.quan@amd.com>
Acked-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Vega20 uses ring id 1 for page queues EOP irq while previous
ASICs take ring id 3.
Signed-off-by: Evan Quan <evan.quan@amd.com>
Acked-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

We need new invalidation engine layout due to new SDMA page
queues added.

V2: fix coding style and add correct return value
Signed-off-by: Evan Quan <evan.quan@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Oak Zeng <Oak.Zeng@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

As two more SDMA page queue rings are added on Vega20.
Signed-off-by: Evan Quan <evan.quan@amd.com>
Reviewed-by: Oak Zeng <Oak.Zeng@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

When the fence is already signaled it is perfectly normal to get a NULL
fence here. But since we can't export that we need to use a stub fence.
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Chunming Zhou <david1.zhou@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Currently driver only psp v11 support vmr.

v2: squash in unused variable removal (Alex)
Signed-off-by: Emily Deng <Emily.Deng@amd.com>
Reviewed-by: Xiangliang Yu <Xiangliang.Yu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

If PSP FW is running already, driver will not load PSP FW again and skip
it. So psp fw version is not correct if reading it from FW binary file,
need to get right version from register.
Signed-off-by: Emily Deng <Emily.Deng@amd.com>
Reviewed-by: Xiangliang Yu <Xiangliang.Yu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

There is no need to access register such as mmSMC_IND_INDEX_11
and mmSMC_IND_DATA_11, PCIE_INDEX, PCIE_DATA through KIQ because
they are VF-copy.
Signed-off-by: Emily Deng <Emily.Deng@amd.com>
Acked-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

XGMI hive put kfd_pre_reset into amdgpu_device_lock_adev,
but outside req_full_gpu of sriov.
It would make sriov hang during reset.
Signed-off-by: Wentao Lou <Wentao.Lou@amd.com>
Reviewed-by: Shaoyun Liu <Shaoyun.Liu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Pull request of 2018-12-13

Two minor fixes for next pull.
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Thomas Hellstrom <thellstrom@vmware.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181213130848.3080-1-thellstrom@vmware.com

This time around, seeing some love for some older hw:

 - a2xx gpu support for apq8060 (hp touchpad) and imx5 (headless
   gpu-only mode)
 - a2xx gpummu support (a2xx was pre-iommu)
 - mdp4 display support for apq8060/touchpad

For display/dpu:

 - a big pile of continuing dpu fixes and cleanups

On the gpu side of things:

 - per-submit statistics and traceevents for better profiling
 - a6xx crashdump support
 - decouple get_iova() and page pinning.. so we can unpin from
   physical memory inactive bo's while using softpin to lower
   cpu overhead
 - new interface to set debug names on GEM BOs and debugfs
   output improvements
 - additional submit flag to indicate buffers that are used
   to dump (so $debugfs/rd cmdstream dumping is useful with
   softpin + state-objects)
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Rob Clark <robdclark@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/CAF6AEGvVvLPD9_Z4kyfGe98Y--byj6HbxHivEYSgF7Rq7=bFnw@mail.gmail.com

Mostly just initial support for Turing TU104/TU106 chipsets.  Support
for TU102 is missing as I don't yet have HW, but it should be trivial
to add in later in the merge window (in theory).

It's a bit of a rough first pass that'll get improved in future
releases as a finish figuring out some of the other HW changes, but
it's good enough as it stands for modesetting and suspend/resume etc.

Acceleration bring-up is incomplete due to NVIDIA not yet having
provided FW images for me to use, though command submission and copy
engines are functional already.
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Ben Skeggs <skeggsb@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/CACAvsv7KmfcQqZcx+wh_1UKjTovp4PH_5UVMfeyxUu-M9WLZfw@mail.gmail.com

drm/tegra: Changes for v4.21-rc1

These changes contain a couple of minor fixes for host1x and the Falcon
library in Tegra DRM. There are also a couple of missing pieces that
finally enable support for host1x, VIC and display on Tegra194. I've
also added a patch that enables audio over HDMI using the SOR which has
been tested, and works, on both Tegra186 and Tegra194.
Signed-off-by: Dave Airlie <airlied@redhat.com>

From: Thierry Reding <thierry.reding@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181207134712.32683-1-thierry.reding@gmail.com

[airlied: make etnaviv build again]

amdgpu:
- DC trace support
- More DC documentation
- XGMI hive reset support
- Rework IH interaction with KFD
- Misc fixes and cleanups
- Powerplay updates for newer polaris variants
- Add cursor plane update fast path
- Enable gpu reset by default on CI parts
- Fix config with KFD/HSA not enabled

amdkfd:
- Limit vram overcommit
- dmabuf support
- Support for doorbell BOs

ttm:
- Support for simultaneous submissions to multiple engines

scheduler:
- Add helpers for hw with preemption support
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Alex Deucher <alexdeucher@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181207233119.16861-1-alexander.deucher@amd.com

[Why]
Legacy cursor plane updates from drm helpers go through the full
atomic codepath. A high volume of cursor updates through this slow
code path can cause subsequent page-flips to skip vblank intervals
since each individual update is slow.

This problem is particularly noticeable for the compton compositor.

[How]
A fast path for cursor plane updates is added by using DRM asynchronous
commit support provided by async_check and async_update. These don't do
a full state/flip_done dependency stall and they don't block other
commit work.

However, DC still expects itself to be single-threaded for anything
that can issue register writes. Screen corruption or hangs can occur
if write sequences overlap. Every call that potentially perform
register writes needs to be guarded for asynchronous updates to work.
The dc_lock mutex was added for this.

Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=106175Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Acked-by: Andrey Grodzovsky <andrey.grodzovsky@amd.com>
Reviewed-by Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>