- 19 Jul, 2014 1 commit
-
-
git://git.infradead.org/users/jcooper/linuxThomas Gleixner authored
irqchip core changes for v3.17 (round #3) from Jason Cooper * gic: Add GICv3 driver * atmel: Move atmel aic driver from arch code to irqchip/
-
- 18 Jul, 2014 2 commits
-
-
Jason Cooper authored
Topic branch set up to facilitate merging the rest of the series which removes the driver from arch code.
-
Jason Cooper authored
From local branch irqchip/gic, this is topic branch that was set up to facilitate merging other changes depending on the new GICv3 driver.
-
- 17 Jul, 2014 6 commits
-
-
Boris BREZILLON authored
Define SoCs that need irq fixups before enabling the AIC irqchip. At the moment we're only fixing irq generated by the RTC block, but other fixups will be added later on. Signed-off-by:
Boris BREZILLON <boris.brezillon@free-electrons.com> Link: https://lkml.kernel.org/r/1405016741-2407-4-git-send-email-boris.brezillon@free-electrons.comSigned-off-by:
Jason Cooper <jason@lakedaemon.net>
-
Boris BREZILLON authored
Provide an implementation to fix RTC irqs before enabling the irqchip. This was previously done in arch/arm/mach-at91/sysirq_mask.c but as we're trying to use standard implementation (IRQCHIP_DECLARE and automatic call of irqchip_init within arch/arm/kernel/irq.c) we need to do those fixups in the irqchip driver. Signed-off-by:
-
Boris BREZILLON authored
Add irq fixup infrastructure to handle IP blocks connected to shared irqs that are left in an unknown state when booting the kernel. In this case the IP block which has not masked its interrupt and has no driver loaded (either because it is not compiled or because it is not loaded yet) might generate spurious interrupts when another IP block request the shared irq. A good example of this case is the RTC block on which register configs are kept even after a shutdown (if a proper VDDcore is supplied), and thus might generate spurious interrupts when the platform is switched on. Signed-off-by:
-
Boris BREZILLON authored
Add AIC (Advanced Interrupt Controller) and AIC5 (AIC5 is an evolution of the AIC block) drivers. Put common code in irq-atmel-aic-common.c/.h so that both driver can access shared functions (this will ease maintenance). These drivers are only compatible with dt enabled board and replace the old implementation found in arch/arm/mach-at91/irq.c. Signed-off-by:
Nicolas Ferre <nicolas.ferre@atmel.com> Link: https://lkml.kernel.org/r/1405012462-766-4-git-send-email-boris.brezillon@free-electrons.comSigned-off-by:
-
Boris BREZILLON authored
Move atmel aic driver doc to the interrupt-controller directory as the new driver now lays in drivers/irqchip/atmel-aic.c. Signed-off-by:
-
Boris BREZILLON authored
Export the generic irq map function in order to provide irq_domain ops with generic mapping and specific of xlate function (needed by the new atmel AIC driver). Signed-off-by:
Thomas Gleixner <tglx@linutronix.de> Link: https://lkml.kernel.org/r/1405012462-766-2-git-send-email-boris.brezillon@free-electrons.comSigned-off-by:
-
- 15 Jul, 2014 1 commit
-
-
Rafael J. Wysocki authored
If an IRQ has been configured for wakeup via enable_irq_wake(), the driver who has done that must be prepared for receiving interrupts after suspend_device_irqs() has returned, so there is no need to "suspend" such IRQs. Moreover, if drivers using enable_irq_wake() actually want to receive interrupts after suspend_device_irqs() has returned, they need to add IRQF_NO_SUSPEND to the IRQ flags while requesting the IRQs, which shouldn't be necessary (it also goes a bit too far, as IRQF_NO_SUSPEND causes the IRQ to be ignored by suspend_device_irqs() all the time regardless of whether or not it has been configured for signaling wakeup). For the above reasons, make __disable_irq() ignore IRQ descriptors with IRQD_WAKEUP_STATE set when its suspend argument is true which effectively causes them to behave like IRQs with IRQF_NO_SUSPEND set. This also allows IRQs configured for wakeup via enable_irq_wake() to work as wakeup interrupts for the "freeze" (suspend-to-idle) sleep mode automatically just like for any other sleep states. Signed-off-by:
Rafael J. Wysocki <rafael.j.wysocki@intel.com> Cc: Li Aubrey <aubrey.li@linux.intel.com> Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com> Cc: One Thousand Gnomes <gnomes@lxorguk.ukuu.org.uk> Link: http://lkml.kernel.org/r/4679574.kGUnqAuNl9@vostro.rjw.lanSigned-off-by:
-
- 08 Jul, 2014 3 commits
-
-
Marc Zyngier authored
The Generic Interrupt Controller (version 3) offers services that are similar to GICv2, with a number of additional features: - Affinity routing based on the CPU MPIDR (ARE) - System register for the CPU interfaces (SRE) - Support for more that 8 CPUs - Locality-specific Peripheral Interrupts (LPIs) - Interrupt Translation Services (ITS) This patch adds preliminary support for GICv3 with ARE and SRE, non-secure mode only. It relies on higher exception levels to grant ARE and SRE access. Support for LPI and ITS will be added at a later time. Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Jason Cooper <jason@lakedaemon.net> Reviewed-by:
Zi Shen Lim <zlim@broadcom.com> Reviewed-by:
Christoffer Dall <christoffer.dall@linaro.org> Reviewed-by:
Tirumalesh Chalamarla <tchalamarla@cavium.com> Reviewed-by:
Yun Wu <wuyun.wu@huawei.com> Reviewed-by:
Zhen Lei <thunder.leizhen@huawei.com> Tested-by: Tirumalesh Chalamarla<tchalamarla@cavium.com> Tested-by:
Radha Mohan Chintakuntla <rchintakuntla@cavium.com> Acked-by:
Catalin Marinas <catalin.marinas@arm.com> Signed-off-by:
Marc Zyngier <marc.zyngier@arm.com> Reviewed-by:
Mark Rutland <mark.rutland@arm.com> Link: https://lkml.kernel.org/r/1404140510-5382-3-git-send-email-marc.zyngier@arm.comSigned-off-by:
-
Marc Zyngier authored
A few GICv2 low-level function are actually very useful to GICv3, and it makes some sense to share them across the two drivers. They end-up in their own file, with an additional parameter used to ensure an optional synchronization (unused on GICv2). Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Jason Cooper <jason@lakedaemon.net> Acked-by:
-
git://git.infradead.org/users/jcooper/linuxThomas Gleixner authored
irqchip core changes form Jason Cooper * or1k-pic: Migrate driver from arch/openrisc * crossbar: Cleanup series
-
- 01 Jul, 2014 2 commits
-
-
Jason Cooper authored
-
Stefan Kristiansson authored
In addition to consolidating the or1k-pic with other interrupt controllers, this makes OpenRISC less tied to its on-cpu interrupt controller. All or1k-pic specific parts are moved out of irq.c and into drivers/irqchip/irq-or1k-pic.c In that transition, the functionality have been divided into three chip variants. One that handles level triggered interrupts, one that handles edge triggered interrupts and one that handles the interrupt controller that is present in the or1200 OpenRISC cpu implementation. Signed-off-by:
Stefan Kristiansson <stefan.kristiansson@saunalahti.fi> Link: https://lkml.kernel.org/r/1401136302-27654-1-git-send-email-stefan.kristiansson@saunalahti.fiAcked-by:
Jonas Bonn <jonas@southpole.se> Signed-off-by:
-
- 30 Jun, 2014 16 commits
-
-
Nishanth Menon authored
On certain platforms such as DRA7, SPIs 0, 1, 2, 3, 5, 6, 10, 131, 132, 133 are direct wired to hardware blocks bypassing crossbar. This quirky implementation is *NOT* supposed to be the expectation of crossbar hardware usage. However, these are already marked in our description of the hardware with SKIP and RESERVED where appropriate. Unfortunately, we need to be able to refer to these hardwired IRQs. So, to request these, crossbar driver can use the existing information from it's table that these SKIP/RESERVED maps are direct wired sources and generic allocation/programming of crossbar should be avoided. Signed-off-by:
Nishanth Menon <nm@ti.com> Signed-off-by:
Sricharan R <r.sricharan@ti.com> Acked-by:
Santosh Shilimkar <santosh.shilimkar@ti.com> Link: https://lkml.kernel.org/r/1403766634-18543-17-git-send-email-r.sricharan@ti.comSigned-off-by:
-
Nishanth Menon authored
The current crossbar description does not include the description required for the consumer of the crossbar, a.k.a devices whoes events pass through the crossbar into the GIC interrupt controller. So, provide documentation for the same. Signed-off-by:
-
Nishanth Menon authored
This is a basic check to ensure that crossbar register needs to be written. This ensures that we have a common check which is used in both map and unmap logic. Signed-off-by:
-
Nishanth Menon authored
Currently we attempt to map any crossbar value to an IRQ, however, this is not correct from hardware perspective. There is a max crossbar event number upto which hardware supports. So describe the same in device tree using 'ti,max-crossbar-sources' property and use it to validate requests. [ jac - remove MAX_SOURCES from binding doc, use integer because we shouldn't put implementation details in the binding docs ] Signed-off-by:
-
Sricharan R authored
Adding kerneldoc for unmap callback function. Signed-off-by:
-
Sricharan R authored
If crossbar_of_init returns with a error, then set the cb pointer to null. Signed-off-by:
-
Nishanth Menon authored
Using err1,2,3,4 etc makes it hard to ensure a new exit path in the middle will not result in spurious changes, so rename the error paths as per the function it does. Signed-off-by:
-
Nishanth Menon authored
crossbar_of_init always returns -ENOMEM in case of errors. There can be other causes of failure like invalid data from DT. So return a appropriate error value for that case. Signed-off-by:
-
Nishanth Menon authored
Adding missing properties for kerneldoc (@write) and cleanup of harmless warnings while we are here. kerneldoc warnings: Warning(drivers/irqchip/irq-crossbar.c:27): missing initial short description on line: * struct crossbar_device: crossbar device description Info(drivers/irqchip/irq-crossbar.c:27): Scanning doc for struct Warning(drivers/irqchip/irq-crossbar.c:39): No description found for parameter 'write' 2 warnings Signed-off-by:
-
Nishanth Menon authored
There is absolutely no need for crossbar driver to expose functions and variables into global namespace. So make them all static Also fix a couple of checkpatch warnings. Fixes sparse warnings: drivers/irqchip/irq-crossbar.c:129:29: warning: symbol 'routable_irq_domain_ops' was not declared. Should it be static? drivers/irqchip/irq-crossbar.c:261:12: warning: symbol 'irqcrossbar_init' was not declared. Should it be static? Checkpatch warnings: WARNING: Prefer kcalloc over kzalloc with multiply + cb->irq_map = kzalloc(max * sizeof(int), GFP_KERNEL); WARNING: Prefer kcalloc over kzalloc with multiply + cb->register_offsets = kzalloc(max * sizeof(int), GFP_KERNEL); Signed-off-by:
-
Nishanth Menon authored
IS_ERR_VALUE makes sense only *if* there could be valid values in negative error range. But in the cases that we do use it, there is no such case. Just remove the same. Signed-off-by:
-
Nishanth Menon authored
Reverse the search algorithm to ensure that address mapping and IRQ allocation logics are proper. This makes the below bugs visible sooner. class 1. address space errors -> example: reg = <a size_b> ti,max-irqs = is a wrong parameter class 2: irq-reserved list - which decides which entries in the address space is not actually wired in class 3: wrong list of routable-irqs. In general allocating from max to min tends to have benefits in ensuring the different issues that may be present in dts is easily caught at definition time, rather than at a later point in time. Signed-off-by:
-
Nishanth Menon authored
Since crossbar is s/w configurable, the initial settings of the crossbar cannot be assumed to be sane. This implies that: a) On initialization all un-reserved crossbars must be initialized to a known 'safe' value. b) When unmapping the interrupt, the safe value must be written to ensure that the crossbar mapping matches with interrupt controller usage. So provide a safe value in the dt data to map if '0' is not safe for the platform and use it during init and unmap While at this, fix the below checkpatch warning. Fixes checkpatch warning: WARNING: Unnecessary space before function pointer arguments #37: FILE: drivers/irqchip/irq-crossbar.c:37: + void (*write) (int, int); Signed-off-by:
-
Nishanth Menon authored
When, in the system due to varied reasons, interrupts might be unusable due to hardware behavior, but register maps do exist, then those interrupts should be skipped while mapping irq to crossbars. Signed-off-by:
-
Nishanth Menon authored
If irq_of_parse_and_map is executed twice, the same crossbar is mapped to two different GIC interrupts. This is completely undesirable. Instead, check if the requested crossbar event is pre-allocated and provide that GIC mapping back to caller if already allocated. Signed-off-by:
-
Nishanth Menon authored
Today '0' is actually reserved, but may not be the same in the future. So, use a flag to mark the GIC interrupts that are reserved. Signed-off-by:
-
- 27 Jun, 2014 2 commits
-
-
git://git.infradead.org/users/jcooper/linuxThomas Gleixner authored
irqchip core changes for v3.17 * nvic: use generic noop function * spear_shirq: generic cleanup, simplification, and refactoring
-
Thomas Gleixner authored
Reason: The next pull request depends on that Signed-off-by:
-
- 24 Jun, 2014 7 commits
-
-
Thomas Gleixner authored
The extra register data structure is pointless. Move the offsets of the status and the mask register into the shirq block structure. Signed-off-by:
Viresh Kumar <viresh.kumar@linaro.org> Signed-off-by:
-
Thomas Gleixner authored
Only spear300 has an actual mask register for the RAS interrupts. Add an irq chip pointer to the shirq struct and initialize spear300 with the actual implementation and the others with dummy_irq_chip. The disabled RAS3 block has no irq chip assigned, so we can check for this and remove the disabled member. Signed-off-by:
-
Thomas Gleixner authored
"ack" is actually a mask in the parent irq. The demultiplexer and the handlers run with interrupts disabled. No point in masking and unmasking the parent. Signed-off-by:
-
Thomas Gleixner authored
I don't know if there are less efficient ways to code that. Get rid of the loop mess and use efficient code. Signed-off-by:
-
Thomas Gleixner authored
None of the chips has a ACK register. The code brainlessly fiddles with the enable register, so it might even reenable a disabled interrupt at least on spear300. Signed-off-by:
-
Thomas Gleixner authored
Calculate the status mask at compile time, not at runtime. Signed-off-by:
-
Thomas Gleixner authored
No point in doing a full irq lookup, when the desc pointer is available. Signed-off-by:
-
