- 21 Jun, 2017 9 commits
-
-
Prameela Rani Garnepudi authored
Boot parameters are changed in new firmware. Also three new sdio sleep parameters are added for ultra low power save. Signed-off-by:
Prameela Rani Garnepudi <prameela.j04cs@gmail.com> Signed-off-by:
Amitkumar Karwar <amit.karwar@redpinesignals.com> Signed-off-by:
Kalle Valo <kvalo@codeaurora.org>
-
Prameela Rani Garnepudi authored
RS9113 chipset supports Coex feature. Initial frame exchanges during device initialization happens on coex queue. This patch adds the handling for coex queue. Signed-off-by:
Prameela Rani Garnepudi <prameela.j04cs@gmail.com> Signed-off-by:
Amitkumar Karwar <amit.karwar@redpinesignals.com> Signed-off-by:
Kalle Valo <kvalo@codeaurora.org>
-
Prameela Rani Garnepudi authored
Before firmware load, sometimes false interrupts are received. System hang is observed if interrupt handler is not registered to receive these interrupts. Hence interrupt handler registration is moved before firmware load. We will drop these false interrupts as these are not from the device. Signed-off-by:
Prameela Rani Garnepudi <prameela.j04cs@gmail.com> Signed-off-by:
Amitkumar Karwar <amit.karwar@redpinesignals.com> Signed-off-by:
Kalle Valo <kvalo@codeaurora.org>
-
Amitkumar Karwar authored
Currently macros are used for FSM states. We will replace it with enum so that new state can be added easily without worrying about macro value. Signed-off-by:
Amitkumar Karwar <amit.karwar@redpinesignals.com> Signed-off-by:
Kalle Valo <kvalo@codeaurora.org>
-
Prameela Rani Garnepudi authored
usb device id and vendor id for RS9113 chipset are included. So it can be used through usb interface. Signed-off-by:
Prameela Rani Garnepudi <prameela.j04cs@gmail.com> Signed-off-by:
Amitkumar Karwar <amit.karwar@redpinesignals.com> Signed-off-by:
Kalle Valo <kvalo@codeaurora.org>
-
Shawn Lin authored
debugfs_remove already check mwifiex_dfs_dir, so remove it. Signed-off-by:
Shawn Lin <shawn.lin@rock-chips.com> Signed-off-by:
Kalle Valo <kvalo@codeaurora.org>
-
Caesar Wang authored
This patch uses WARN level is not printed by default. In some cases, some boards have always met the unused log be printed as follows. ... [23193.523182] mwifiex_pcie 0000:01:00.0: mwifiex_get_cfp: cannot find cfp by band 2 & channel=13 freq=0 [23378.633684] mwifiex_pcie 0000:01:00.0: mwifiex_get_cfp: cannot find cfp by band 2 & channel=13 freq=0 Due to we used the wifi default area was US and didn't support 12~14 channels. As Frequencies: * 2412 MHz [1] (30.0 dBm) * 2417 MHz [2] (30.0 dBm) * 2422 MHz [3] (30.0 dBm) * 2427 MHz [4] (30.0 dBm) * 2432 MHz [5] (30.0 dBm) * 2437 MHz [6] (30.0 dBm) * 2442 MHz [7] (30.0 dBm) * 2447 MHz [8] (30.0 dBm) * 2452 MHz [9] (30.0 dBm) * 2457 MHz [10] (30.0 dBm) * 2462 MHz [11] (30.0 dBm) * 2467 MHz [12] (disabled) * 2472 MHz [13] (disabled) * 2484 MHz [14] (disabled) Also, as the commit 1b499cb7 ("mwifiex: disable channel filtering feature in firmware"), it proved to be a feature to get better scan result from overlapping channel. Even there could be AP from overlapping channel (might be 12/13/14 in this case), it will be filtered depend on reg domain rules. e.g: ... if (ch->flags & IEEE80211_CHAN_DISABLED) continue; So it should not been an ERROR, use the WARN level to instead it for now. Signed-off-by:
Caesar Wang <wxt@rock-chips.com> Acked-by:
Xinming Hu <huxm@marvell.com> Signed-off-by:
Kalle Valo <kvalo@codeaurora.org>
-
Kevin Lo authored
The REG_USTIME_TSF (US Time Tuning for TSF) definition of Realtek chips should be 0x55C. Signed-off-by:
Kevin Lo <kevlo@kevlo.org> Signed-off-by:
Kalle Valo <kvalo@codeaurora.org>
-
Hans de Goede authored
The brcm43430 chip needs different firmware files for chip revision 0 and 1. The file currently in linux-firmware is for revision 1 only. This commit makes brcmfmac request brcmfmac43430a0-sdio.bin instead of brcmfmac43430-sdio.bin for revision 0 chips. Note that the behavior for revision 1 chips is not changed, ideally those would load brcmfmac43430a1-sdio.bin, but that will break existing setups. Signed-off-by:
Hans de Goede <hdegoede@redhat.com> Acked-by:
Arend van Spriel <arend.vanspriel@broadcom.com> Signed-off-by:
Kalle Valo <kvalo@codeaurora.org>
-
- 13 Jun, 2017 19 commits
-
-
Gustavo A. R. Silva authored
Remove unnecessary variable and refactor the code. Addresses-Coverity-ID: 1365000 Signed-off-by:
Gustavo A. R. Silva <garsilva@embeddedor.com> Signed-off-by:
Kalle Valo <kvalo@codeaurora.org>
-
Sebastian Reichel authored
Motorola Droid 4 uses a WL 1285C. With differences between chips not being public let's add explicit binding for wl1285 instead of relying on wl1283 being very similar. Reviewed-by:
Rob Herring <robh@kernel.org> Acked-by:
Kalle Valo <kvalo@codeaurora.org> Acked-by:
Tony Lindgren <tony@atomide.com> Signed-off-by:
Sebastian Reichel <sebastian.reichel@collabora.co.uk> Signed-off-by:
Kalle Valo <kvalo@codeaurora.org>
-
Binoy Jayan authored
The semaphore 'async_sem' is used as a simple mutex, so it should be written as one. Semaphores are going away in the future. Signed-off-by:
Binoy Jayan <binoy.jayan@linaro.org> Reviewed-by:
Arnd Bergmann <arnd@arndb.de> Signed-off-by:
Kalle Valo <kvalo@codeaurora.org>
-
Yan-Hsuan Chuang authored
Instead of rssi status, the btcoex also needs to get the link status of the wifi. In addition, some of the rssi status can be merged into link status. Signed-off-by:
Yan-Hsuan Chuang <yhchuang@realtek.com> Signed-off-by:
Larry Finger <Larry.Finger@lwfinger.net> Cc: Ping-Ke Shih <pkshih@realtek.com> Cc: Birming Chiu <birming@realtek.com> Cc: Shaofu <shaofu@realtek.com> Cc: Steven Ting <steventing@realtek.com> Signed-off-by:
Kalle Valo <kvalo@codeaurora.org>
-
Yan-Hsuan Chuang authored
These display functions are useless and will not be called in the future. Signed-off-by:
Yan-Hsuan Chuang <yhchuang@realtek.com> Signed-off-by:
Larry Finger <Larry.Finger@lwfinger.net> Cc: Ping-Ke Shih <pkshih@realtek.com> Cc: Birming Chiu <birming@realtek.com> Cc: Shaofu <shaofu@realtek.com> Cc: Steven Ting <steventing@realtek.com> Signed-off-by:
Kalle Valo <kvalo@codeaurora.org>
-
Yan-Hsuan Chuang authored
When initializing, gather BT information in struct btcoexist and provide them to wifi driver. Signed-off-by:
Yan-Hsuan Chuang <yhchuang@realtek.com> Signed-off-by:
Larry Finger <Larry.Finger@lwfinger.net> Cc: Ping-Ke Shih <pkshih@realtek.com> Cc: Birming Chiu <birming@realtek.com> Cc: Shaofu <shaofu@realtek.com> Cc: Steven Ting <steventing@realtek.com> Signed-off-by:
Kalle Valo <kvalo@codeaurora.org>
-
Yan-Hsuan Chuang authored
Hook the external functions for newer ICs such as 8821a and 8192e. Rename ex_halbtc8192e2ant_halt_notify to ex_btc8192e2ant_halt_notify. Signed-off-by:
Yan-Hsuan Chuang <yhchuang@realtek.com> Signed-off-by:
Larry Finger <Larry.Finger@lwfinger.net> Cc: Ping-Ke Shih <pkshih@realtek.com> Cc: Birming Chiu <birming@realtek.com> Cc: Shaofu <shaofu@realtek.com> Cc: Steven Ting <steventing@realtek.com> Signed-off-by:
Kalle Valo <kvalo@codeaurora.org>
-
Yan-Hsuan Chuang authored
When the hardware is turned on and in the initialization stage, the PTA circuit is unstable. Hence we need to force some hardware settings to make sure the PTA circuit work correctly, otherwise it may affect the user's experience. Signed-off-by:
Yan-Hsuan Chuang <yhchuang@realtek.com> Signed-off-by:
Larry Finger <Larry.Finger@lwfinger.net> Cc: Ping-Ke Shih <pkshih@realtek.com> Cc: Birming Chiu <birming@realtek.com> Cc: Shaofu <shaofu@realtek.com> Cc: Steven Ting <steventing@realtek.com> Signed-off-by:
Kalle Valo <kvalo@codeaurora.org>
-
Yan-Hsuan Chuang authored
Hook the chip-specific PnP notify functions for the wifi driver to notify btcoexistence. Signed-off-by:
Yan-Hsuan Chuang <yhchuang@realtek.com> Signed-off-by:
Larry Finger <Larry.Finger@lwfinger.net> Cc: Ping-Ke Shih <pkshih@realtek.com> Cc: Birming Chiu <birming@realtek.com> Cc: Shaofu <shaofu@realtek.com> Cc: Steven Ting <steventing@realtek.com> Signed-off-by:
Kalle Valo <kvalo@codeaurora.org>
-
Yan-Hsuan Chuang authored
The btcoex is sometimes unstable because there are some unexpected behaviors before the firmware has been downloaded successfully. Therefore we force the antenna path settings to avoid this, then let the firmware control the btcoexistence when the firmware is ready. Signed-off-by:
Yan-Hsuan Chuang <yhchuang@realtek.com> Signed-off-by:
Larry Finger <Larry.Finger@lwfinger.net> Cc: Ping-Ke Shih <pkshih@realtek.com> Cc: Birming Chiu <birming@realtek.com> Cc: Shaofu <shaofu@realtek.com> Cc: Steven Ting <steventing@realtek.com> Signed-off-by:
Kalle Valo <kvalo@codeaurora.org>
-
Yan-Hsuan Chuang authored
These external functions are for BT-coexistence, so remove the "hal" prefix for consistancy. Signed-off-by:
Yan-Hsuan Chuang <yhchuang@realtek.com> Signed-off-by:
Larry Finger <Larry.Finger@lwfinger.net> Cc: Ping-Ke Shih <pkshih@realtek.com> Cc: Birming Chiu <birming@realtek.com> Cc: Shaofu <shaofu@realtek.com> Cc: Steven Ting <steventing@realtek.com> Signed-off-by:
Kalle Valo <kvalo@codeaurora.org>
-
Yan-Hsuan Chuang authored
For some external functions that have hardware dependency, we need to know the type of the hardware before invoking them. Signed-off-by:
Yan-Hsuan Chuang <yhchuang@realtek.com> Signed-off-by:
Larry Finger <Larry.Finger@lwfinger.net> Cc: Ping-Ke Shih <pkshih@realtek.com> Cc: Birming Chiu <birming@realtek.com> Cc: Shaofu <shaofu@realtek.com> Cc: Steven Ting <steventing@realtek.com> Signed-off-by:
Kalle Valo <kvalo@codeaurora.org>
-
Colin Ian King authored
The current code allocates cmd_skb and then will leak this if band->band is an illegal value. It is simpler to sanity check the band first before allocating cmd_skb so that we don't have to free cmd_skb if an invalid band occurs. Detected by CoverityScan, CID#1437561 ("Resource Leak") Signed-off-by:
Colin Ian King <colin.king@canonical.com> Reviewed-by:
Igor Mitsyanko <igor.mitsyanko.os@quantenna.com> Signed-off-by:
Kalle Valo <kvalo@codeaurora.org>
-
Colin Ian King authored
function mwifiex_ret_pkt_aggr_ctrl can be made static as it does not need to be in global scope. Cleans up sparse warning: "symbol 'mwifiex_ret_pkt_aggr_ctrl' was not declared. Should it be static?" Signed-off-by:
Colin Ian King <colin.king@canonical.com> Signed-off-by:
Kalle Valo <kvalo@codeaurora.org>
-
Peter S. Housel authored
An earlier change to this function (3bdae810) fixed a leak in the case of an unsuccessful call to brcmf_sdiod_buffrw(). However, the glom_skb buffer, used for emulating a scattering read, is never used or referenced after its contents are copied into the destination buffers, and therefore always needs to be freed by the end of the function. Fixes: 3bdae810 ("brcmfmac: Fix glob_skb leak in brcmf_sdiod_recv_chain") Fixes: a413e39a ("brcmfmac: fix brcmf_sdcard_recv_chain() for host without sg support") Cc: stable@vger.kernel.org # 4.9.x- Signed-off-by:
Peter S. Housel <housel@acm.org> Signed-off-by:
Arend van Spriel <arend.vanspriel@broadcom.com> Signed-off-by:
Kalle Valo <kvalo@codeaurora.org>
-
Martin Michlmayr authored
Fix grammar issue in error message about ISO3166. Signed-off-by:
Martin Michlmayr <tbm@cyrius.com> Acked-by:
Arend van Spriel <arend.vanspriel@broadcom.com> Signed-off-by:
Kalle Valo <kvalo@codeaurora.org>
-
Arend Van Spriel authored
Add support to handle scheduled scan request containing BSSID in the matchsets. The firmware can send event upon finding BSSIDs and SSIDs. To get these in one event the bit REPORT_SEPARATELY needed to be removed from the flags in brcmf_pno_config(). Reviewed-by:
Hante Meuleman <hante.meuleman@broadcom.com> Reviewed-by:
Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com> Reviewed-by:
Franky Lin <franky.lin@broadcom.com> Signed-off-by:
Arend van Spriel <arend.vanspriel@broadcom.com> Signed-off-by:
Kalle Valo <kvalo@codeaurora.org>
-
Arend Van Spriel authored
The request references kept in pno are accessed in user-space context and in firmware event handler context. As such we need to protect it with a lock. As both context allow sleep a mutex seems appropriate. Reviewed-by:
Hante Meuleman <hante.meuleman@broadcom.com> Reviewed-by:
Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com> Reviewed-by:
Franky Lin <franky.lin@broadcom.com> Signed-off-by:
Arend van Spriel <arend.vanspriel@broadcom.com> Signed-off-by:
Kalle Valo <kvalo@codeaurora.org>
-
Arend Van Spriel authored
This change adds support for multi-scheduled scan in the driver. It currently relies on g-scan support in firmware and will set struct wiphy::max_sched_scan_reqs accordingly. This is limited to 16 concurrent requests. The firmware currently has a limit of 64 channels that can be configured for all requests in total regardless whether there are duplicates. So if a request uses 35 channels there are 29 channels left for another request. When user-space does not specify any channels cfg80211 will add all channels defined by the wiphy instance to the request, which makes reaching the limit rather easy for dual-band devices. Reviewed-by:
Hante Meuleman <hante.meuleman@broadcom.com> Reviewed-by:
Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com> Reviewed-by:
Franky Lin <franky.lin@broadcom.com> Signed-off-by:
Arend van Spriel <arend.vanspriel@broadcom.com> Signed-off-by:
Kalle Valo <kvalo@codeaurora.org>
-
- 12 Jun, 2017 7 commits
-
-
Kalle Valo authored
Merge tag 'iwlwifi-next-for-kalle-2017-06-06' of git://git.kernel.org/pub/scm/linux/kernel/git/iwlwifi/iwlwifi-next First batch of iwlwifi driver patches 4.13 * Loads of FW API documentation improvements (for tools and htmldoc); * Continued work for the new A000 family; * Bumped the maximum supported FW API to 31; * Improve the differentiation between 8000, 9000 and A000 families; * A lot of fixes and cleanups here and there; kvalo: There were conflicts iwl_mvm_stop_device() and iwl_mvm_tcool_set_cur_state(). The former was easy but latter needed more thought. Apparently the mutex was taken too late, so I fixed so that the mutex is taken first and then check for iwl_mvm_firmware_running().
-
David S. Miller authored
Merge tag 'wireless-drivers-next-for-davem-2017-06-12' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next Kalle Valo says: ==================== wireless-drivers-next patches for 4.13 The first pull request for 4.13. We have a new driver qtnfmac, but also rsi driver got a support for new firmware and supporting ath10k SDIO devices was started. Major changes: ath10k * add initial SDIO support (still work in progress) rsi * new loading for the new firmware version rtlwifi * final patches for the new btcoex support rt2x00 * add device ID for Epson WN7512BEP qtnfmac * new driver for Quantenna QSR10G chipsets ==================== Signed-off-by:
David S. Miller <davem@davemloft.net>
-
David S. Miller authored
Paolo Abeni says: ==================== udp: reduce cache pressure In the most common use case, many skb fields are not used by recvmsg(), and the few ones actually accessed lays on cold cachelines, which leads to several cache miss per packet. This patch series attempts to reduce such misses with different strategies: * caching the interesting fields in the scratched space * avoid accessing at all uninteresting fields * prefetching Tested using the udp_sink program by Jesper[1] as the receiver, an h/w l4 rx hash on the ingress nic, so that the number of ingress nic rx queues hit by the udp traffic could be controlled via ethtool -L. The udp_sink program was bound to the first idle cpu, to get more stable numbers. On a single numa node receiver: nic rx queues vanilla patched kernel delta 1 1850 kpps 1850 kpps 0% 2 2370 kpps 2700 kpps 13.9% 16 2000 kpps 2220 kpps 11% [1] https://github.com/netoptimizer/network-testing/blob/master/src/udp_sink.c v1 -> v2: - replaced secpath_reset() with skb_release_head_state() - changed udp_dev_scratch fields types to u{32,16} variant, replaced bitfield with bool v2 -> v3: - no changes, tested against apachebench for performances regression ==================== Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Paolo Abeni authored
when udp_recvmsg() is executed, on x86_64 and other archs, most skb fields are on cold cachelines. If the skb are linear and the kernel don't need to compute the udp csum, only a handful of skb fields are required by udp_recvmsg(). Since we already use skb->dev_scratch to cache hot data, and there are 32 bits unused on 64 bit archs, use such field to cache as much data as we can, and try to prefetch on dequeue the relevant fields that are left out. This can save up to 2 cache miss per packet. v1 -> v2: - changed udp_dev_scratch fields types to u{32,16} variant, replaced bitfiled with bool Signed-off-by:
Paolo Abeni <pabeni@redhat.com> Acked-by:
Eric Dumazet <edumazet@google.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Paolo Abeni authored
Since UDP no more uses sk->destructor, we can clear completely the skb head state before enqueuing. Amend and use skb_release_head_state() for that. All head states share a single cacheline, which is not normally used/accesses on dequeue. We can avoid entirely accessing such cacheline implementing and using in the UDP code a specialized skb free helper which ignores the skb head state. This saves a cacheline miss at skb deallocation time. v1 -> v2: replaced secpath_reset() with skb_release_head_state() Signed-off-by:
Paolo Abeni <pabeni@redhat.com> Acked-by:
Eric Dumazet <edumazet@google.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Paolo Abeni authored
The same code is replicated in 3 different places; move it to a common helper. Signed-off-by:
Paolo Abeni <pabeni@redhat.com> Acked-by:
Eric Dumazet <edumazet@google.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Niklas Söderlund authored
The hardware supports the MTU to be changed and the driver it self is somewhat prepared to support this. This patch hooks up the callbacks to be able to change the MTU from user-space. Signed-off-by:
Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se> Acked-by:
Sergei Shtylyov <sergei.shtylyov@cogentembedded.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
- 11 Jun, 2017 4 commits
-
-
Daniel Borkmann authored
Make use of recently implemented stack_depth tracking for arm64 JIT, so that stack usage can be reduced heavily for programs not using tail calls at least. Signed-off-by:
Daniel Borkmann <daniel@iogearbox.net> Acked-by:
Alexei Starovoitov <ast@kernel.org> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linuxDavid S. Miller authored
Saeed Mahameed says: ==================== mlx5-updates-2017-06-11 This series provides updates to mlx5 header rewrite feature, from Or Gerlitz. and three more small updates From maor and eran. ------- Or says: Packets belonging to flows which are different by matching may still need to go through the same header re-writes (e.g set the current routing hop MACs and issue TTL decrement). To minimize the number of modify header IDs, we add a cache for header re-write IDs which is keyed by the binary chain of modify header actions. The caching is supported for both eswitch and NIC use-cases, where the actual conversion of the code to use caching comes in separate patches, one per use-case. Using a per field mask field, the TC pedit action supports modifying partial fields. The last patch enables offloading that. ------- From Maor, update flow table commands layout to the latest HW spec. From Eran, ethtool connector type reporting updates. ==================== Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Grygorii Strashko authored
CPSW driver does not handle this interrupt, so there are no reasons to enable it in hardware. Signed-off-by:
Grygorii Strashko <grygorii.strashko@ti.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Grygorii Strashko authored
CPSW driver supports PTP v1 messages, but for unknown reasons this filter is not advertised. As result, ./tools/testing/selftests/networking/timestamping/timestamping utility can't be used for testing of CPSW RX timestamping with option SOF_TIMESTAMPING_RX_HARDWARE, because it uses HWTSTAMP_FILTER_PTP_V1_L4_SYNC filter. Hence, fix it by advertising HWTSTAMP_FILTER_PTP_V1_L4_XXX filters in CPSW driver. Signed-off-by:
Grygorii Strashko <grygorii.strashko@ti.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
- 10 Jun, 2017 1 commit
-
-
David S. Miller authored
Daniel Borkmann says: ==================== Misc BPF updates This set contains a couple of misc updates: stack usage reduction for perf_sample_data in tracing progs, reduction of stale data in verifier on register state transitions that I still had in my queue and few selftest improvements as well as bpf_set_hash() helper for tc programs. ==================== Signed-off-by:
David S. Miller <davem@davemloft.net>
-