Dynamic debug has a run time knob to enable function name printing.
Remove this from dev_dbg() calls.

Furthermore, functional tracing when enabled can show what function is
called, therefore remove empty dev_dbg() calls.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

!!'s behaviour isn't that obvious and sparse complained about it, so
let's replace it with a ternary condition.
Signed-off-by: Quentin Schulz <quentin.schulz@bootlin.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

The resistance member in ccs811_reading struct is an unsigned 16-bit
integer variable used to store RAW_DATA register bytes read from CCS811.
It is kind of misleading to name this struct member as resistance.

About the RAW_DATA register bytes, the CCS811 datasheet states that:
-----
Two byte read only register which contains the latest readings from the
sense resistor.

The most significant 6 bits of the Byte 0 contain the value of the current
through the sensor (0μA to 63μA).

The lower 10 bits contain (as computed from the ADC) the readings of the
voltage across the sensor with the selected current (1023 = 1.65V)"
-----

Hence, the RAW_DATA register byte contains information about electric
current and voltage of the CCS811 sensor. Calling this struct member
'resistance' is kind of misleading, although both electric current and
voltage are needed to calculate the electrical resistance of the sensor
using Ohm's law, V = I x R, in which a new channel type of IIO_RESISTANCE
may be added to the driver in the future.
Signed-off-by: Richard Lai <richard@richardman.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

Remove blank space after a cast to conform to Linux kernel coding style.
Problem found using checkpatch.
Signed-off-by: Santha Meena Ramamoorthy <santhameena13@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Match alignment with open parenthesis to conform to Linux kernel coding
style. Problem found using checkpatch.
Signed-off-by: Santha Meena Ramamoorthy <santhameena13@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Add space around arithmetic operators ('+', '-' and '*') to conform to
Linux kernel coding style. Problem found using checkpatch.
Signed-off-by: Santha Meena Ramamoorthy <santhameena13@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Mostly this change just reverses the primary conditional so most of
the code can be pulled back a tab, which fixes some code style
warnings.
Signed-off-by: Quytelda Kahja <quytelda@tamalin.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Since the testing for host endianness and in-driver conversion were
removed in 77e8a501, the gdm_endian struct contains only one member,
and can therefore be simplified to a single u8 variable.
Signed-off-by: Quytelda Kahja <quytelda@tamalin.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Fix lines with a trailing open parenthesis, which is a coding style issue.
Signed-off-by: Quytelda Kahja <quytelda@tamalin.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Now that the fsl-mc bus core infrastructure is out of staging, the
remaining irqchip glue code used (irq-gic-v3-its-fsl-mc-msi.c) goes
to drivers/irqchip.

Create new Kconfig option for irqchip code that depends on
FSL_MC_BUS and ARM_GIC_V3_ITS. This ensures irqchip code only
gets built on ARM64 platforms. We can now remove #ifdef
GENERIC_MSI_DOMAIN_OPS as it was only needed for x86.
Signed-off-by: Stuart Yoder <stuyoder@gmail.com>
[rebased, add dpaa2_eth and dpio #include updates]
Signed-off-by: Laurentiu Tudor <laurentiu.tudor@nxp.com>
[rebased, split irqchip to separate patch]
Signed-off-by: Bogdan Purcareata <bogdan.purcareata@nxp.com>
[add Kconfig dependency on ARM_GIC_V3_ITS]
Signed-off-by: Ioana Radulescu <ruxandra.radulescu@nxp.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Move the source files out of staging into their final locations:
  -mc.h include file in drivers/staging/fsl-mc/include go to include/linux/fsl
  -source files in drivers/staging/fsl-mc/bus go to drivers/bus/fsl-mc
  -overview.rst, providing an overview of DPAA2, goes to
   Documentation/networking/dpaa2/overview.rst

Update or delete other remaining staging files -- Makefile, Kconfig, TODO.
Update dpaa2_eth and dpio staging drivers.
Add integration bits for the documentation build system.
Signed-off-by: Stuart Yoder <stuyoder@gmail.com>
[rebased, add dpaa2_eth and dpio #include updates]
Signed-off-by: Laurentiu Tudor <laurentiu.tudor@nxp.com>
[rebased, split irqchip to separate patch]
Signed-off-by: Bogdan Purcareata <bogdan.purcareata@nxp.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Fix "Avoid camelCase" issue found by checkpatch.pl script.
Signed-off-by: Ajay Singh <ajay.kathat@microchip.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Fix "Avoid camelCase" issue found by checkpatch.pl script.
Signed-off-by: Ajay Singh <ajay.kathat@microchip.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Fix "Avoid camelCase" issue found by checkpatch.pl script.
Signed-off-by: Ajay Singh <ajay.kathat@microchip.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Fix "Avoid camelCase" issue found by checkpatch.pl script.
Signed-off-by: Ajay Singh <ajay.kathat@microchip.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Fix "Avoid camelCase" issue found by checkpatch.pl script.
Signed-off-by: Ajay Singh <ajay.kathat@microchip.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Fix "Avoid caseCase" issue found by checkpatch.pl script.
Signed-off-by: Ajay Singh <ajay.kathat@microchip.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Fix "Avoid camelCase" issue found by checkpatch.pl script.
Signed-off-by: Ajay Singh <ajay.kathat@microchip.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Fix "Avoid camelCase" issue found by checkpatch.pl script.
Signed-off-by: Ajay Singh <ajay.kathat@microchip.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Fix "Avoid camelCase" issue found by checkpatch.pl script.
Signed-off-by: Ajay Singh <ajay.kathat@microchip.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Fix "Avoid camelCase" issue found by checkpatch.pl script.
Signed-off-by: Ajay Singh <ajay.kathat@microchip.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Fix "Avoid camelCase" issue found by checkpatch.pl script.
Signed-off-by: Ajay Singh <ajay.kathat@microchip.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Fix "Avoid camelCase" issue found by checkpatch.pl script.
Signed-off-by: Ajay Singh <ajay.kathat@microchip.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

We should just return directly if memdup_user() fails. The current code
tries to free "param" which is an error pointer so it will Oops.

Fixes: 2baddf26 ("staging: lustre: use memdup_user to allocate memory and copy from user")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ksnc_rx_iov_space is currently a union of two arrays,
one of 'struct kvec', the other of 'struct bio_vec'.

The 'struct bio_vec' option is never used.  The
array of kvec is used to read in a packet header, or
to read data that needs to be skipped so as to synchronize
with a packet boundary.
In each case the target memory location is a virtual address,
never a page, so 'struct bio_vec' is never needed.

When we read into a page, different code steps up a separate
array of 'struct bio_vec'.

So remove the bio_vec option, and remove the union ksock_rxiovspace..
Signed-off-by: NeilBrown <neilb@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

When fid fetches a new range from the server, it commits
to it (*output = *out) *before* performing sanity checks.
This looks backwards.
Don't commit to a value until it has been found to be sane.
Signed-off-by: NeilBrown <neilb@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

lcs_space can change while the lock is not held
if an RPC in underway.  This can be detected by
seq->ls_update being set.

In this case, reading or writing the value should return
-EBUSY.

Also, the D_INFO CDEBUG() which reports the lcs_space being
updated never fires, as it tests the wrong value -
ldebugfs_fid_write_common() returns 'count' on success.

Finally, this return value should be returned from
ldebugfs_fid_space_seq_write(), rather than always returning 'count',
so that errors can be detected.
Signed-off-by: NeilBrown <neilb@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

seq_fid_alloc_fini() is tiny and only called
from two places in the one function.  We can move
both those calls earlier and merge them so only
one call is needed.  At that point, there is no
value added by having a separate function.

Also instead of using ++ and -- on ->lcs_update to
toggle between 0 and 1, explicitly set to 0 or 1
as appropriate.

Moving the locking earlier means that the code which updates
seq->lcs_fid is now protected, so
ldebugfs_fid_fid_seq_show() now cannot see a torn value.
Signed-off-by: NeilBrown <neilb@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Rather than open-coding a wait event loop twice,
use wait_event_cmd() to wait, dropping the spinlock
over schedule().
This does require duplicating part of the wait
condition, but that is just three tests on values that
are in registers or in cache, so the cost is small
and the increased readability is large.
Signed-off-by: NeilBrown <neilb@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

There is only one place where this lock is held
while the task might sleep - in
  ldebugfs_fid_space_seq_write()
while ldebugfs_fid_write_common() is called.

This call can easily be taken out of the locked region
by asking it to parse the user data into a local variable,
and then copying that variable into ->lcs_space while
holding the lock.

Note that ldebugfs_gid_write_common returns >0 on
success, so use that to gate updating ->lcs_space.

So make that change, and convert lcs_mutex to a spinlock
named lcs_lock.  spinlocks are slightly cheaper than mutexes
and using one makes is clear that the lock is only held for
a short time.
Signed-off-by: NeilBrown <neilb@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

1/ use list_for_each_entry_safe() instead of
   list_for_each_safe() and similar.

2/ use list_first_entry() and list_last_entry() where appropriate.

3/ When removing everything from a list, use
     while ((x = list_first_entry_or_null()) {
   as it makes the intent clear

4/ No need to take a spinlock in a structure that is about
   to be freed - we must have exclusive access at this stage.
Signed-off-by: NeilBrown <neilb@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Possibly the most interesting is the for-loop with no body.
Rearranging and initializing end_dirent on each iteration of
the outer while, makes the intent clearer.
Reviewed-by: "Eremin, Dmitry" <dmitry.eremin@intel.com>
Signed-off-by: NeilBrown <neilb@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

There is no "struct cfs_crypto_hash_desc" structure.  There
are only pointers to this structure, which are cast back and
forth to struct ahash_request.
So discard cfs_crypto_hash_desc, and just use ahash_request directly.
Signed-off-by: NeilBrown <neilb@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The only interesting difference between libcfs_kvzalloc()
and kvzalloc() is that the former appears to work
with GFP_NOFS, which the latter gives a WARN_ON_ONCE()
when that is attempted.

Each libcfs_kvzalloc() should really be analysed
and either converted to a kzalloc() call if the size is never
more than a page, or to use GFP_KERNEL if no locks are held.

If there is ever a case where locks are held and a large allocation
is needed, then some other technique should be used.

It might be nice to not always blindly zero pages too...

For now, just convert libcfs_kvzalloc() calls to
kvzalloc(), and let the warning remind us that there is work to do.
Signed-off-by: NeilBrown <neilb@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Using vmalloc with GFP_NOFS is not supported as vmalloc
performs some internal allocations with GFP_KERNEL.

So in cases where the size passed to libcfs_kvzalloc()
is clearly at most 1 page, convert to kzalloc().
In cases where the call clearly doesn't hold any
filesystem locks, convert to GFP_KERNEL.

Unfortunately there are many more that are not easy to fix.
Signed-off-by: NeilBrown <neilb@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This library code is unnecessarily generic, but also
not generic enough.  Library code that performs
allocations should always take a gfp_flags argument.

So discard the library and in the one file where it is used,
just use kzalloc or krealloc as needed.
In this context, it is clear that vmalloc is never needed.
Signed-off-by: NeilBrown <neilb@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This function is used precisely once, and is sufficiently
trivial that it may as well be open-coded.

Doing so helpfully highlights the similarity
between the new kvzalloc_node() call and the already existing
kzalloc_node() call in the same function.
Signed-off-by: NeilBrown <neilb@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

cfs_block_sigsinv() and cfs_restore_sigs() are now
simple enough to inline them.
This means we can discard linux-prim.c
Signed-off-by: NeilBrown <neilb@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

According to comment for set_current_blocked() in
kernel/signal.c, changing ->blocked directly is wrong.
sigprocmask() should be called instead.

So change cfs_block_sigsinv() and cfs_restore_sigs()
to use sigprocmask().
For consistency, change them to pass the sigset_t by reference
rather than by value.

Also fix cfs_block_sigsinv() so that it correctly blocks
signals above 32 on a 32bit host.
Signed-off-by: NeilBrown <neilb@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

cfs_block_sigs() is never used.
cfs_clear_sigpending() is never used.
cfs_block_allsigs() is no longer used.

So those three functions can go.
Signed-off-by: NeilBrown <neilb@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>