- 10 Feb, 2017 40 commits
-
-
Dan Carpenter authored
commit 79ad07d4 upstream. There is a cut and paste issue here. The bug is that we are allocating more memory than necessary for msp_maps. We should be allocating enough space for a map_info struct (144 bytes) but we instead allocate enough for an mtd_info struct (1840 bytes). It's a small waste. The other part of this is not harmful but when we allocated msp_flash then we allocated enough space fro a map_info pointer instead of an mtd_info pointer. But since pointers are the same size it works out fine. Anyway, I decided to clean up all three allocations a bit to make them a bit more consistent and clear. Fixes: 68aa0fa8 ('[MTD] PMC MSP71xx flash/rootfs mappings') Signed-off-by:
Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by:
Brian Norris <computersforpeace@gmail.com> Signed-off-by:
Willy Tarreau <w@1wt.eu>
-
Brian Norris authored
commit f3c63795 upstream. Commit 073db4a5 ("mtd: fix: avoid race condition when accessing mtd->usecount") fixed a race condition but due to poor ordering of the mutex acquisition, introduced a potential deadlock. The deadlock can occur, for example, when rmmod'ing the m25p80 module, which will delete one or more MTDs, along with any corresponding mtdblock devices. This could potentially race with an acquisition of the block device as follows. -> blktrans_open() -> mutex_lock(&dev->lock); -> mutex_lock(&mtd_table_mutex); -> del_mtd_device() -> mutex_lock(&mtd_table_mutex); -> blktrans_notify_remove() -> del_mtd_blktrans_dev() -> mutex_lock(&dev->lock); This is a classic (potential) ABBA deadlock, which can be fixed by making the A->B ordering consistent everywhere. There was no real purpose to the ordering in the original patch, AFAIR, so this shouldn't be a problem. This ordering was actually already present in del_mtd_blktrans_dev(), for one, where the function tried to ensure that its caller already held mtd_table_mutex before it acquired &dev->lock: if (mutex_trylock(&mtd_table_mutex)) { mutex_unlock(&mtd_table_mutex); BUG(); } So, reverse the ordering of acquisition of &dev->lock and &mtd_table_mutex so we always acquire mtd_table_mutex first. Snippets of the lockdep output follow: # modprobe -r m25p80 [ 53.419251] [ 53.420838] ====================================================== [ 53.427300] [ INFO: possible circular locking dependency detected ] [ 53.433865] 4.3.0-rc6 #96 Not tainted [ 53.437686] ------------------------------------------------------- [ 53.444220] modprobe/372 is trying to acquire lock: [ 53.449320] (&new->lock){+.+...}, at: [<c043fe4c>] del_mtd_blktrans_dev+0x80/0xdc [ 53.457271] [ 53.457271] but task is already holding lock: [ 53.463372] (mtd_table_mutex){+.+.+.}, at: [<c0439994>] del_mtd_device+0x18/0x100 [ 53.471321] [ 53.471321] which lock already depends on the new lock. [ 53.471321] [ 53.479856] [ 53.479856] the existing dependency chain (in reverse order) is: [ 53.487660] -> #1 (mtd_table_mutex){+.+.+.}: [ 53.492331] [<c043fc5c>] blktrans_open+0x34/0x1a4 [ 53.497879] [<c01afce0>] __blkdev_get+0xc4/0x3b0 [ 53.503364] [<c01b0bb8>] blkdev_get+0x108/0x320 [ 53.508743] [<c01713c0>] do_dentry_open+0x218/0x314 [ 53.514496] [<c0180454>] path_openat+0x4c0/0xf9c [ 53.519959] [<c0182044>] do_filp_open+0x5c/0xc0 [ 53.525336] [<c0172758>] do_sys_open+0xfc/0x1cc [ 53.530716] [<c000f740>] ret_fast_syscall+0x0/0x1c [ 53.536375] -> #0 (&new->lock){+.+...}: [ 53.540587] [<c063f124>] mutex_lock_nested+0x38/0x3cc [ 53.546504] [<c043fe4c>] del_mtd_blktrans_dev+0x80/0xdc [ 53.552606] [<c043f164>] blktrans_notify_remove+0x7c/0x84 [ 53.558891] [<c04399f0>] del_mtd_device+0x74/0x100 [ 53.564544] [<c043c670>] del_mtd_partitions+0x80/0xc8 [ 53.570451] [<c0439aa0>] mtd_device_unregister+0x24/0x48 [ 53.576637] [<c046ce6c>] spi_drv_remove+0x1c/0x34 [ 53.582207] [<c03de0f0>] __device_release_driver+0x88/0x114 [ 53.588663] [<c03de19c>] device_release_driver+0x20/0x2c [ 53.594843] [<c03dd9e8>] bus_remove_device+0xd8/0x108 [ 53.600748] [<c03dacc0>] device_del+0x10c/0x210 [ 53.606127] [<c03dadd0>] device_unregister+0xc/0x20 [ 53.611849] [<c046d878>] __unregister+0x10/0x20 [ 53.617211] [<c03da868>] device_for_each_child+0x50/0x7c [ 53.623387] [<c046eae8>] spi_unregister_master+0x58/0x8c [ 53.629578] [<c03e12f0>] release_nodes+0x15c/0x1c8 [ 53.635223] [<c03de0f8>] __device_release_driver+0x90/0x114 [ 53.641689] [<c03de900>] driver_detach+0xb4/0xb8 [ 53.647147] [<c03ddc78>] bus_remove_driver+0x4c/0xa0 [ 53.652970] [<c00cab50>] SyS_delete_module+0x11c/0x1e4 [ 53.658976] [<c000f740>] ret_fast_syscall+0x0/0x1c [ 53.664621] [ 53.664621] other info that might help us debug this: [ 53.664621] [ 53.672979] Possible unsafe locking scenario: [ 53.672979] [ 53.679169] CPU0 CPU1 [ 53.683900] ---- ---- [ 53.688633] lock(mtd_table_mutex); [ 53.692383] lock(&new->lock); [ 53.698306] lock(mtd_table_mutex); [ 53.704658] lock(&new->lock); [ 53.707946] [ 53.707946] *** DEADLOCK *** Fixes: 073db4a5 ("mtd: fix: avoid race condition when accessing mtd->usecount") Reported-by:
Felipe Balbi <balbi@ti.com> Tested-by:
-
Mark Bloch authored
commit 9db0ff53 upstream. When there is a CM id object that has port assigned to it, it means that the cm-id asked for the specific port that it should go by it, but if that port was removed (hot-unplug event) the cm-id was not updated. In order to fix that the port keeps a list of all the cm-id's that are planning to go by it, whenever the port is removed it marks all of them as invalid. This commit fixes a kernel panic which happens when running traffic between guests and we force reboot a guest mid traffic, it triggers a kernel panic: Call Trace: [<ffffffff815271fa>] ? panic+0xa7/0x16f [<ffffffff8152b534>] ? oops_end+0xe4/0x100 [<ffffffff8104a00b>] ? no_context+0xfb/0x260 [<ffffffff81084db2>] ? del_timer_sync+0x22/0x30 [<ffffffff8104a295>] ? __bad_area_nosemaphore+0x125/0x1e0 [<ffffffff81084240>] ? process_timeout+0x0/0x10 [<ffffffff8104a363>] ? bad_area_nosemaphore+0x13/0x20 [<ffffffff8104aabf>] ? __do_page_fault+0x31f/0x480 [<ffffffff81065df0>] ? default_wake_function+0x0/0x20 [<ffffffffa0752675>] ? free_msg+0x55/0x70 [mlx5_core] [<ffffffffa0753434>] ? cmd_exec+0x124/0x840 [mlx5_core] [<ffffffff8105a924>] ? find_busiest_group+0x244/0x9f0 [<ffffffff8152d45e>] ? do_page_fault+0x3e/0xa0 [<ffffffff8152a815>] ? page_fault+0x25/0x30 [<ffffffffa024da25>] ? cm_alloc_msg+0x35/0xc0 [ib_cm] [<ffffffffa024e821>] ? ib_send_cm_dreq+0xb1/0x1e0 [ib_cm] [<ffffffffa024f836>] ? cm_destroy_id+0x176/0x320 [ib_cm] [<ffffffffa024fb00>] ? ib_destroy_cm_id+0x10/0x20 [ib_cm] [<ffffffffa034f527>] ? ipoib_cm_free_rx_reap_list+0xa7/0x110 [ib_ipoib] [<ffffffffa034f590>] ? ipoib_cm_rx_reap+0x0/0x20 [ib_ipoib] [<ffffffffa034f5a5>] ? ipoib_cm_rx_reap+0x15/0x20 [ib_ipoib] [<ffffffff81094d20>] ? worker_thread+0x170/0x2a0 [<ffffffff8109b2a0>] ? autoremove_wake_function+0x0/0x40 [<ffffffff81094bb0>] ? worker_thread+0x0/0x2a0 [<ffffffff8109aef6>] ? kthread+0x96/0xa0 [<ffffffff8100c20a>] ? child_rip+0xa/0x20 [<ffffffff8109ae60>] ? kthread+0x0/0xa0 [<ffffffff8100c200>] ? child_rip+0x0/0x20 Fixes: a977049d ("[PATCH] IB: Add the kernel CM implementation") Signed-off-by:
Mark Bloch <markb@mellanox.com> Signed-off-by:
Erez Shitrit <erezsh@mellanox.com> Reviewed-by:
Maor Gottlieb <maorg@mellanox.com> Signed-off-by:
Leon Romanovsky <leon@kernel.org> Signed-off-by:
Doug Ledford <dledford@redhat.com> Signed-off-by:
-
Tariq Toukan authored
commit 5b810a24 upstream. The real QP is destroyed in case of the ref count reaches zero, but for XRC target QPs this call was missed and caused to QP leaks. Let's call to destroy for all flows. Fixes: 0e0ec7e0 ('RDMA/core: Export ib_open_qp() to share XRC...') Signed-off-by:
Tariq Toukan <tariqt@mellanox.com> Signed-off-by:
Noa Osherovich <noaos@mellanox.com> Signed-off-by:
-
Matan Barak authored
commit 593ff73b upstream. Currently, if ib_copy_to_udata fails, the CQ won't be deleted from the radix tree and the HW (HW2SW). Fixes: 225c7b1f ('IB/mlx4: Add a driver Mellanox ConnectX InfiniBand adapters') Signed-off-by:
Matan Barak <matanb@mellanox.com> Signed-off-by:
Daniel Jurgens <danielj@mellanox.com> Reviewed-by:
-
Alex Vesker authored
commit e5ac40cd upstream. Because of an incorrect bit-masking done on the join state bits, when handling a join request we failed to detect a difference between the group join state and the request join state when joining as send only full member (0x8). This caused the MC join request not to be sent. This issue is relevant only when SRIOV is enabled and SM supports send only full member. This fix separates scope bits and join states bits a nibble each. Fixes: b9c5d6a6 ('IB/mlx4: Add multicast group (MCG) paravirtualization for SR-IOV') Signed-off-by:
Alex Vesker <valex@mellanox.com> Signed-off-by:
-
Alex Vesker authored
commit 344bacca upstream. This fix solves a race between light flush and on the fly joins. Light flush doesn't set the device to down and unset IPOIB_OPER_UP flag, this means that if while flushing we have a MC join in progress and the QP was attached to BC MGID we can have a mismatches when re-attaching a QP to the BC MGID. The light flush would set the broadcast group to NULL causing an on the fly join to rejoin and reattach to the BC MCG as well as adding the BC MGID to the multicast list. The flush process would later on remove the BC MGID and detach it from the QP. On the next flush the BC MGID is present in the multicast list but not found when trying to detach it because of the previous double attach and single detach. [18332.714265] ------------[ cut here ]------------ [18332.717775] WARNING: CPU: 6 PID: 3767 at drivers/infiniband/core/verbs.c:280 ib_dealloc_pd+0xff/0x120 [ib_core] ... [18332.775198] Hardware name: Red Hat KVM, BIOS Bochs 01/01/2011 [18332.779411] 0000000000000000 ffff8800b50dfbb0 ffffffff813fed47 0000000000000000 [18332.784960] 0000000000000000 ffff8800b50dfbf0 ffffffff8109add1 0000011832f58300 [18332.790547] ffff880226a596c0 ffff880032482000 ffff880032482830 ffff880226a59280 [18332.796199] Call Trace: [18332.798015] [<ffffffff813fed47>] dump_stack+0x63/0x8c [18332.801831] [<ffffffff8109add1>] __warn+0xd1/0xf0 [18332.805403] [<ffffffff8109aebd>] warn_slowpath_null+0x1d/0x20 [18332.809706] [<ffffffffa025d90f>] ib_dealloc_pd+0xff/0x120 [ib_core] [18332.814384] [<ffffffffa04f3d7c>] ipoib_transport_dev_cleanup+0xfc/0x1d0 [ib_ipoib] [18332.820031] [<ffffffffa04ed648>] ipoib_ib_dev_cleanup+0x98/0x110 [ib_ipoib] [18332.825220] [<ffffffffa04e62c8>] ipoib_dev_cleanup+0x2d8/0x550 [ib_ipoib] [18332.830290] [<ffffffffa04e656f>] ipoib_uninit+0x2f/0x40 [ib_ipoib] [18332.834911] [<ffffffff81772a8a>] rollback_registered_many+0x1aa/0x2c0 [18332.839741] [<ffffffff81772bd1>] rollback_registered+0x31/0x40 [18332.844091] [<ffffffff81773b18>] unregister_netdevice_queue+0x48/0x80 [18332.848880] [<ffffffffa04f489b>] ipoib_vlan_delete+0x1fb/0x290 [ib_ipoib] [18332.853848] [<ffffffffa04df1cd>] delete_child+0x7d/0xf0 [ib_ipoib] [18332.858474] [<ffffffff81520c08>] dev_attr_store+0x18/0x30 [18332.862510] [<ffffffff8127fe4a>] sysfs_kf_write+0x3a/0x50 [18332.866349] [<ffffffff8127f4e0>] kernfs_fop_write+0x120/0x170 [18332.870471] [<ffffffff81207198>] __vfs_write+0x28/0xe0 [18332.874152] [<ffffffff810e09bf>] ? percpu_down_read+0x1f/0x50 [18332.878274] [<ffffffff81208062>] vfs_write+0xa2/0x1a0 [18332.881896] [<ffffffff812093a6>] SyS_write+0x46/0xa0 [18332.885632] [<ffffffff810039b7>] do_syscall_64+0x57/0xb0 [18332.889709] [<ffffffff81883321>] entry_SYSCALL64_slow_path+0x25/0x25 [18332.894727] ---[ end trace 09ebbe31f831ef17 ]--- Fixes: ee1e2c82 ("IPoIB: Refresh paths instead of flushing them on SM change events") Signed-off-by:
-
Erez Shitrit authored
commit 68c6bcdd upstream. The function send_leave sets the member: group->query_id (group->query_id = ret) after calling the sa_query, but leave_handler can be executed before the setting and it might delete the group object, and will get a memory corruption. Additionally, this patch gets rid of group->query_id variable which is not used. Fixes: faec2f7b ('IB/sa: Track multicast join/leave requests') Signed-off-by:
-
Erez Shitrit authored
commit 546481c2 upstream. When a new CM connection is being requested, ipoib driver copies data from the path pointer in the CM/tx object, the path object might be invalid at the point and memory corruption will happened later when now the CM driver will try using that data. The next scenario demonstrates it: neigh_add_path --> ipoib_cm_create_tx --> queue_work (pointer to path is in the cm/tx struct) #while the work is still in the queue, #the port goes down and causes the ipoib_flush_paths: ipoib_flush_paths --> path_free --> kfree(path) #at this point the work scheduled starts. ipoib_cm_tx_start --> copy from the (invalid)path pointer: (memcpy(&pathrec, &p->path->pathrec, sizeof pathrec);) -> memory corruption. To fix that the driver now starts the CM/tx connection only if that specific path exists in the general paths database. This check is protected with the relevant locks, and uses the gid from the neigh member in the CM/tx object which is valid according to the ref count that was taken by the CM/tx. Fixes: 839fcaba ('IPoIB: Connected mode experimental support') Signed-off-by:
-
Emmanouil Maroudas authored
commit 993f88f1 upstream. Fix typo in edac_inc_ue_error() to increment ue_noinfo_count instead of ce_noinfo_count. Signed-off-by:
Emmanouil Maroudas <emmanouil.maroudas@gmail.com> Cc: Mauro Carvalho Chehab <mchehab@osg.samsung.com> Cc: linux-edac <linux-edac@vger.kernel.org> Fixes: 4275be63 ("edac: Change internal representation to work with layers") Link: http://lkml.kernel.org/r/1461425580-5898-1-git-send-email-emmanouil.maroudas@gmail.comSigned-off-by:
Borislav Petkov <bp@suse.de> Signed-off-by:
-
Tejun Heo authored
commit 22b886dd upstream. Regardless of the previous CPU a timer was on, add_timer_on() currently simply sets timer->flags to the new CPU. As the caller must be seeing the timer as idle, this is locally fine, but the timer leaving the old base while unlocked can lead to race conditions as follows. Let's say timer was on cpu 0. cpu 0 cpu 1 ----------------------------------------------------------------------------- del_timer(timer) succeeds del_timer(timer) lock_timer_base(timer) locks cpu_0_base add_timer_on(timer, 1) spin_lock(&cpu_1_base->lock) timer->flags set to cpu_1_base operates on @timer operates on @timer This triggered with mod_delayed_work_on() which contains "if (del_timer()) add_timer_on()" sequence eventually leading to the following oops. BUG: unable to handle kernel NULL pointer dereference at (null) IP: [<ffffffff810ca6e9>] detach_if_pending+0x69/0x1a0 ... Workqueue: wqthrash wqthrash_workfunc [wqthrash] task: ffff8800172ca680 ti: ffff8800172d0000 task.ti: ffff8800172d0000 RIP: 0010:[<ffffffff810ca6e9>] [<ffffffff810ca6e9>] detach_if_pending+0x69/0x1a0 ... Call Trace: [<ffffffff810cb0b4>] del_timer+0x44/0x60 [<ffffffff8106e836>] try_to_grab_pending+0xb6/0x160 [<ffffffff8106e913>] mod_delayed_work_on+0x33/0x80 [<ffffffffa0000081>] wqthrash_workfunc+0x61/0x90 [wqthrash] [<ffffffff8106dba8>] process_one_work+0x1e8/0x650 [<ffffffff8106e05e>] worker_thread+0x4e/0x450 [<ffffffff810746af>] kthread+0xef/0x110 [<ffffffff8185980f>] ret_from_fork+0x3f/0x70 Fix it by updating add_timer_on() to perform proper migration as __mod_timer() does. Mike: apply tglx backport Reported-and-tested-by:
Jeff Layton <jlayton@poochiereds.net> Signed-off-by:
Tejun Heo <tj@kernel.org> Cc: Chris Worley <chris.worley@primarydata.com> Cc: bfields@fieldses.org Cc: Michael Skralivetsky <michael.skralivetsky@primarydata.com> Cc: Trond Myklebust <trond.myklebust@primarydata.com> Cc: Shaohua Li <shli@fb.com> Cc: Jeff Layton <jlayton@poochiereds.net> Cc: kernel-team@fb.com Cc: stable@vger.kernel.org Link: http://lkml.kernel.org/r/20151029103113.2f893924@tlielax.poochiereds.net Link: http://lkml.kernel.org/r/20151104171533.GI5749@mtj.duckdns.orgSigned-off-by:
Thomas Gleixner <tglx@linutronix.de> Signed-off-by:
Mike Galbraith <mgalbraith@suse.de> Signed-off-by:
-
Gavin Li authored
commit add12505 upstream. This fixes the "BOGUS urb xfer" warning logged by usb_submit_urb(). Signed-off-by:
Gavin Li <git@thegavinli.com> Acked-by:
Oliver Neukum <oneukum@suse.com> Signed-off-by:
Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by:
-
Krzysztof Kozlowski authored
commit f37fabb8 upstream. In the critical sysfs entry the thermal hwmon was returning wrong temperature to the user-space. It was reporting the temperature of the first trip point instead of the temperature of critical trip point. For example: /sys/class/hwmon/hwmon0/temp1_crit:50000 /sys/class/thermal/thermal_zone0/trip_point_0_temp:50000 /sys/class/thermal/thermal_zone0/trip_point_0_type:active /sys/class/thermal/thermal_zone0/trip_point_3_temp:120000 /sys/class/thermal/thermal_zone0/trip_point_3_type:critical Since commit e68b16ab ("thermal: add hwmon sysfs I/F") the driver have been registering a sysfs entry if get_crit_temp() callback was provided. However when accessed, it was calling get_trip_temp() instead of the get_crit_temp(). Fixes: e68b16ab ("thermal: add hwmon sysfs I/F") Signed-off-by:
Krzysztof Kozlowski <krzk@kernel.org> Signed-off-by:
Zhang Rui <rui.zhang@intel.com> [wt: s/thermal_hwmon.c/thermal_core.c in 3.10] Signed-off-by:
-
Linus Walleij authored
commit 307fe9dd upstream. All the scaling of the KXSD9 involves multiplication with a fraction number < 1. However the scaling value returned from IIO_INFO_SCALE was unpredictable as only the micros of the value was assigned, and not the integer part, resulting in scaling like this: $cat in_accel_scale -1057462640.011978 Fix this by assigning zero to the integer part. Tested-by:
Jonathan Cameron <jic23@kernel.org> Signed-off-by:
Linus Walleij <linus.walleij@linaro.org> Signed-off-by:
-
Linus Walleij authored
commit 7ac61a06 upstream. Any readings from the raw interface of the KXSD9 driver will return an empty string, because it does not return IIO_VAL_INT but rather some random value from the accelerometer to the caller. Signed-off-by:
-
Cyrille Pitchen authored
commit 6f6ddbb0 upstream. In some cases a NACK interrupt may be pending in the Status Register (SR) as a result of a previous transfer. However at91_do_twi_transfer() did not read the SR to clear pending interruptions before starting a new transfer. Hence a NACK interrupt rose as soon as it was enabled again at the I2C controller level, resulting in a wrong sequence of operations and strange patterns of behaviour on the I2C bus, such as a clock stretch followed by a restart of the transfer. This first issue occurred with both DMA and PIO write transfers. Also when a NACK error was detected during a PIO write transfer, the interrupt handler used to wrongly start a new transfer by writing into the Transmit Holding Register (THR). Then the I2C slave was likely to reply with a second NACK. This second issue is fixed in atmel_twi_interrupt() by handling the TXRDY status bit only if both the TXCOMP and NACK status bits are cleared. Tested with a at24 eeprom on sama5d36ek board running a linux-4.1-at91 kernel image. Adapted to linux-next. Reported-by:
Peter Rosin <peda@lysator.liu.se> Signed-off-by:
Cyrille Pitchen <cyrille.pitchen@atmel.com> Signed-off-by:
Ludovic Desroches <ludovic.desroches@atmel.com> Tested-by:
Wolfram Sang <wsa@the-dreams.de> Fixes: 93563a6a ("i2c: at91: fix a race condition when using the DMA controller") Signed-off-by:
-
Vladimir Zapolskiy authored
commit 147b36d5 upstream. Race condition between registering an I2C device driver and deregistering an I2C adapter device which is assumed to manage that I2C device may lead to a NULL pointer dereference due to the uninitialized list head of driver clients. The root cause of the issue is that the I2C bus may know about the registered device driver and thus it is matched by bus_for_each_drv(), but the list of clients is not initialized and commonly it is NULL, because I2C device drivers define struct i2c_driver as static and clients field is expected to be initialized by I2C core: i2c_register_driver() i2c_del_adapter() driver_register() ... bus_add_driver() ... ... bus_for_each_drv(..., __process_removed_adapter) ... i2c_do_del_adapter() ... list_for_each_entry_safe(..., &driver->clients, ...) INIT_LIST_HEAD(&driver->clients); To solve the problem it is sufficient to do clients list head initialization before calling driver_register(). The problem was found while using an I2C device driver with a sluggish registration routine on a bus provided by a physically detachable I2C master controller, but practically the oops may be reproduced under the race between arbitraty I2C device driver registration and managing I2C bus device removal e.g. by unbinding the latter over sysfs: % echo 21a4000.i2c > /sys/bus/platform/drivers/imx-i2c/unbind Unable to handle kernel NULL pointer dereference at virtual address 00000000 Internal error: Oops: 17 [#1] SMP ARM CPU: 2 PID: 533 Comm: sh Not tainted 4.9.0-rc3+ #61 Hardware name: Freescale i.MX6 Quad/DualLite (Device Tree) task: e5ada400 task.stack: e4936000 PC is at i2c_do_del_adapter+0x20/0xcc LR is at __process_removed_adapter+0x14/0x1c Flags: NzCv IRQs on FIQs on Mode SVC_32 ISA ARM Segment none Control: 10c5387d Table: 35bd004a DAC: 00000051 Process sh (pid: 533, stack limit = 0xe4936210) Stack: (0xe4937d28 to 0xe4938000) Backtrace: [<c0667be0>] (i2c_do_del_adapter) from [<c0667cc0>] (__process_removed_adapter+0x14/0x1c) [<c0667cac>] (__process_removed_adapter) from [<c0516998>] (bus_for_each_drv+0x6c/0xa0) [<c051692c>] (bus_for_each_drv) from [<c06685ec>] (i2c_del_adapter+0xbc/0x284) [<c0668530>] (i2c_del_adapter) from [<bf0110ec>] (i2c_imx_remove+0x44/0x164 [i2c_imx]) [<bf0110a8>] (i2c_imx_remove [i2c_imx]) from [<c051a838>] (platform_drv_remove+0x2c/0x44) [<c051a80c>] (platform_drv_remove) from [<c05183d8>] (__device_release_driver+0x90/0x12c) [<c0518348>] (__device_release_driver) from [<c051849c>] (device_release_driver+0x28/0x34) [<c0518474>] (device_release_driver) from [<c0517150>] (unbind_store+0x80/0x104) [<c05170d0>] (unbind_store) from [<c0516520>] (drv_attr_store+0x28/0x34) [<c05164f8>] (drv_attr_store) from [<c0298acc>] (sysfs_kf_write+0x50/0x54) [<c0298a7c>] (sysfs_kf_write) from [<c029801c>] (kernfs_fop_write+0x100/0x214) [<c0297f1c>] (kernfs_fop_write) from [<c0220130>] (__vfs_write+0x34/0x120) [<c02200fc>] (__vfs_write) from [<c0221088>] (vfs_write+0xa8/0x170) [<c0220fe0>] (vfs_write) from [<c0221e74>] (SyS_write+0x4c/0xa8) [<c0221e28>] (SyS_write) from [<c0108a20>] (ret_fast_syscall+0x0/0x1c) Signed-off-by:
Vladimir Zapolskiy <vladimir_zapolskiy@mentor.com> Signed-off-by:
-
Dan Carpenter authored
commit e44c153b upstream. The code is checking for negative returns but it should be checking for zero. Fixes: aab3125c ('[media] em28xx: add support for registering multiple i2c buses') Signed-off-by:
Mauro Carvalho Chehab <mchehab@osg.samsung.com> Signed-off-by:
-
Yadi.hu authored
commit 371a0153 upstream. the eg20t driver call request_irq() function before the pch_base_address, base address of i2c controller's register, is assigned an effective value. there is one possible scenario that an interrupt which isn't inside eg20t arrives immediately after request_irq() is executed when i2c controller shares an interrupt number with others. since the interrupt handler pch_i2c_handler() has already active as shared action, it will be called and read its own register to determine if this interrupt is from itself. At that moment, since base address of i2c registers is not remapped in kernel space yet,so the INT handler will access an illegal address and then a error occurs. Signed-off-by:
Yadi.hu <yadi.hu@windriver.com> Signed-off-by:
-
Dave Gerlach authored
commit ad8529fd upstream. Currently omap-rng checks the return value of pm_runtime_get_sync and reports failure if anything is returned, however it should be checking if ret < 0 as pm_runtime_get_sync return 0 on success but also can return 1 if the device was already active which is not a failure case. Only values < 0 are actual failures. Fixes: 61dc0a44 ("hwrng: omap - Fix assumption that runtime_get_sync will always succeed") Signed-off-by:
Dave Gerlach <d-gerlach@ti.com> Signed-off-by:
Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by:
-
Nishanth Menon authored
commit 61dc0a44 upstream. pm_runtime_get_sync does return a error value that must be checked for error conditions, else, due to various reasons, the device maynot be enabled and the system will crash due to lack of clock to the hardware module. Before: 12.562784] [00000000] *pgd=fe193835 12.562792] Internal error: : 1406 [#1] SMP ARM [...] 12.562864] CPU: 1 PID: 241 Comm: modprobe Not tainted 4.7.0-rc4-next-20160624 #2 12.562867] Hardware name: Generic DRA74X (Flattened Device Tree) 12.562872] task: ed51f140 ti: ed44c000 task.ti: ed44c000 12.562886] PC is at omap4_rng_init+0x20/0x84 [omap_rng] 12.562899] LR is at set_current_rng+0xc0/0x154 [rng_core] [...] After the proper checks: [ 94.366705] omap_rng 48090000.rng: _od_fail_runtime_resume: FIXME: missing hwmod/omap_dev info [ 94.375767] omap_rng 48090000.rng: Failed to runtime_get device -19 [ 94.382351] omap_rng 48090000.rng: initialization failed. Fixes: 665d92fa ("hwrng: OMAP: convert to use runtime PM") Cc: Paul Walmsley <paul@pwsan.com> Signed-off-by:
Nishanth Menon <nm@ti.com> Signed-off-by:
-
Krzysztof Kozlowski authored
commit 48a61e1e upstream. Add proper error path (for disabling runtime PM) when registering of hwrng fails. Fixes: b329669e ("hwrng: exynos - Add support for Exynos random number generator") Signed-off-by:
Krzysztof Kozlowski <k.kozlowski@samsung.com> Signed-off-by:
-
Dmitry Torokhov authored
commit b27c0d0c upstream. "calibrate" attribute does not provide "show" methods and thus we should not mark it as readable. Signed-off-by:
Dmitry Torokhov <dmitry.torokhov@gmail.com> Signed-off-by:
-
Dmitry Torokhov authored
commit 47af45d6 upstream. The commit 40974618 ("Input: i8042 - break load dependency ...") correctly set up ps2_cmd_mutex pointer for the KBD port but forgot to do the same for AUX port(s), which results in communication on KBD and AUX ports to clash with each other. Fixes: 40974618 ("Input: i8042 - break load dependency ...") Reported-by:
Bruno Wolff III <bruno@wolff.to> Tested-by:
-
Dmitry Torokhov authored
commit 40974618 upstream. As explained in 1407814240-4275-1-git-send-email-decui@microsoft.com we have a hard load dependency between i8042 and atkbd which prevents keyboard from working on Gen2 Hyper-V VMs. > hyperv_keyboard invokes serio_interrupt(), which needs a valid serio > driver like atkbd.c. atkbd.c depends on libps2.c because it invokes > ps2_command(). libps2.c depends on i8042.c because it invokes > i8042_check_port_owner(). As a result, hyperv_keyboard actually > depends on i8042.c. > > For a Generation 2 Hyper-V VM (meaning no i8042 device emulated), if a > Linux VM (like Arch Linux) happens to configure CONFIG_SERIO_I8042=m > rather than =y, atkbd.ko can't load because i8042.ko can't load(due to > no i8042 device emulated) and finally hyperv_keyboard can't work and > the user can't input: https://bugs.archlinux.org/task/39820 > (Ubuntu/RHEL/SUSE aren't affected since they use CONFIG_SERIO_I8042=y) To break the dependency we move away from using i8042_check_port_owner() and instead allow serio port owner specify a mutex that clients should use to serialize PS/2 command stream. Reported-by:
Mark Laws <mdl@60hz.org> Tested-by:
-
Dan Carpenter authored
commit f4cceb2a upstream. If kmap fails, it leads to memory corruption. Fixes: f64122c1 ('drm: add new QXL driver. (v1.4)') Signed-off-by:
Daniel Vetter <daniel.vetter@ffwll.ch> Link: http://patchwork.freedesktop.org/patch/msgid/20160711084633.GA31411@mwandaSigned-off-by:
-
Michel Dänzer authored
NOTE: This patch only applies to 4.5.y or older kernels. With newer kernels, this problem cannot happen because the driver now uses drm_crtc_vblank_on/off instead of drm_vblank_pre/post_modeset[0]. I consider this patch safer for older kernels than backporting the API change, because drm_crtc_vblank_on/off had various issues in older kernels, and I'm not sure all fixes for those have been backported to all stable branches where this patch could be applied. --------------------- Fixes the vblank interrupt being disabled when it should be on, which can cause at least the following symptoms: * Hangs when running 'xset dpms force off' in a GNOME session with gnome-shell using DRI2. * RandR 1.4 slave outputs freezing with garbage displayed using xf86-video-ati 7.8.0 or newer. [0] See upstream commit: commit 777e3cbc Author: Daniel Vetter <daniel.vetter@ffwll.ch> Date: Thu Jan 21 11:08:57 2016 +0100 drm/radeon: Switch to drm_vblank_on/off Reported-and-Tested-by:Max Staudt <mstaudt@suse.de> Reviewed-by:
Daniel Vetter <daniel@ffwll.ch> Reviewed-by:
Alex Deucher <alexander.deucher@amd.com> Signed-off-by:
Michel Dänzer <michel.daenzer@amd.com> Signed-off-by:
-
Daniel Vetter authored
commit 6f00975c upstream. Somehow this one slipped through, which means drivers without modeset support can be oopsed (since those also don't call drm_mode_config_init, which means the crtc lookup will chase an uninitalized idr). Reported-by:
Alexander Potapenko <glider@google.com> Cc: Alexander Potapenko <glider@google.com> Signed-off-by:
Daniel Vetter <daniel.vetter@intel.com> Reviewed-by:
Chris Wilson <chris@chris-wilson.co.uk> Signed-off-by:
Dave Airlie <airlied@redhat.com> Signed-off-by:
-
Christian König authored
commit 13f479b9 upstream. This bug seems to be present for a very long time. Signed-off-by:
Christian König <christian.koenig@amd.com> Reviewed-by:
-
Ming Lei authored
commit cebf8fd1 upstream. The global mutex of 'gdp_mutex' is used to serialize creating/querying glue dir and its cleanup. Turns out it isn't a perfect way because part(kobj_kset_leave()) of the actual cleanup action() is done inside the release handler of the glue dir kobject. That means gdp_mutex has to be held before releasing the last reference count of the glue dir kobject. This patch moves glue dir's cleanup after kobject_del() in device_del() for avoiding the race. Cc: Yijing Wang <wangyijing@huawei.com> Reported-by:
Chandra Sekhar Lingutla <clingutla@codeaurora.org> Signed-off-by:
Ming Lei <ming.lei@canonical.com> Signed-off-by:
-
Markus Elfring authored
commit 5f0163a5 upstream. The put_device() function tests whether its argument is NULL and then returns immediately. Thus the test around the call is not needed. This issue was detected by using the Coccinelle software. Signed-off-by:
Markus Elfring <elfring@users.sourceforge.net> Signed-off-by:
-
Dan Carpenter authored
commit 8a545f18 upstream. We can't pass error pointers to kfree() or it causes an oops. Fixes: 52b209f7 ('get rid of hostfs_read_inode()') Signed-off-by:
Richard Weinberger <richard@nod.at> Signed-off-by:
-
Jan Kara authored
commit a2ed0b39 upstream. When isofs_mount() is called to mount a device read-write, it returns EACCES even before it checks that the device actually contains an isofs filesystem. This may confuse mount(8) which then tries to mount all subsequent filesystem types in read-only mode. Fix the problem by returning EACCES only once we verify that the device indeed contains an iso9660 filesystem. Fixes: 17b7f7cfReported-by:
Kent Overstreet <kent.overstreet@gmail.com> Reported-by:
Karel Zak <kzak@redhat.com> Signed-off-by:
Jan Kara <jack@suse.cz> Signed-off-by:
-
Oleg Nesterov authored
commit 89f39af1 upstream. Change thaw_super() to check frozen != SB_FREEZE_COMPLETE rather than frozen == SB_UNFROZEN, otherwise it can race with freeze_super() which drops sb->s_umount after SB_FREEZE_WRITE to preserve the lock ordering. In this case thaw_super() will wrongly call s_op->unfreeze_fs() before it was actually frozen, and call sb_freeze_unlock() which leads to the unbalanced percpu_up_write(). Unfortunately lockdep can't detect this, so this triggers misc BUG_ON()'s in kernel/rcu/sync.c. Reported-and-tested-by:
Nikolay Borisov <kernel@kyup.com> Signed-off-by:
Oleg Nesterov <oleg@redhat.com> Signed-off-by:
Al Viro <viro@zeniv.linux.org.uk> Signed-off-by:
-
Vegard Nossum authored
commit 088bf2ff upstream. seq_read() is a nasty piece of work, not to mention buggy. It has (I think) an old bug which allows unprivileged userspace to read beyond the end of m->buf. I was getting these: BUG: KASAN: slab-out-of-bounds in seq_read+0xcd2/0x1480 at addr ffff880116889880 Read of size 2713 by task trinity-c2/1329 CPU: 2 PID: 1329 Comm: trinity-c2 Not tainted 4.8.0-rc1+ #96 Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.9.3-0-ge2fc41e-prebuilt.qemu-project.org 04/01/2014 Call Trace: kasan_object_err+0x1c/0x80 kasan_report_error+0x2cb/0x7e0 kasan_report+0x4e/0x80 check_memory_region+0x13e/0x1a0 kasan_check_read+0x11/0x20 seq_read+0xcd2/0x1480 proc_reg_read+0x10b/0x260 do_loop_readv_writev.part.5+0x140/0x2c0 do_readv_writev+0x589/0x860 vfs_readv+0x7b/0xd0 do_readv+0xd8/0x2c0 SyS_readv+0xb/0x10 do_syscall_64+0x1b3/0x4b0 entry_SYSCALL64_slow_path+0x25/0x25 Object at ffff880116889100, in cache kmalloc-4096 size: 4096 Allocated: PID = 1329 save_stack_trace+0x26/0x80 save_stack+0x46/0xd0 kasan_kmalloc+0xad/0xe0 __kmalloc+0x1aa/0x4a0 seq_buf_alloc+0x35/0x40 seq_read+0x7d8/0x1480 proc_reg_read+0x10b/0x260 do_loop_readv_writev.part.5+0x140/0x2c0 do_readv_writev+0x589/0x860 vfs_readv+0x7b/0xd0 do_readv+0xd8/0x2c0 SyS_readv+0xb/0x10 do_syscall_64+0x1b3/0x4b0 return_from_SYSCALL_64+0x0/0x6a Freed: PID = 0 (stack is not available) Memory state around the buggy address: ffff88011688a000: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ffff88011688a080: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 >ffff88011688a100: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc ^ ffff88011688a180: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc ffff88011688a200: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb ================================================================== Disabling lock debugging due to kernel taint This seems to be the same thing that Dave Jones was seeing here: https://lkml.org/lkml/2016/8/12/334 There are multiple issues here: 1) If we enter the function with a non-empty buffer, there is an attempt to flush it. But it was not clearing m->from after doing so, which means that if we try to do this flush twice in a row without any call to traverse() in between, we are going to be reading from the wrong place -- the splat above, fixed by this patch. 2) If there's a short write to userspace because of page faults, the buffer may already contain multiple lines (i.e. pos has advanced by more than 1), but we don't save the progress that was made so the next call will output what we've already returned previously. Since that is a much less serious issue (and I have a headache after staring at seq_read() for the past 8 hours), I'll leave that for now. Link: http://lkml.kernel.org/r/1471447270-32093-1-git-send-email-vegard.nossum@oracle.comSigned-off-by:
Vegard Nossum <vegard.nossum@oracle.com> Reported-by:
Dave Jones <davej@codemonkey.org.uk> Cc: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by:
Andrew Morton <akpm@linux-foundation.org> Signed-off-by:
Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by:
-
Trond Myklebust authored
commit 304020fe upstream. If the file permissions change on the server, then we may not be able to recover open state. If so, we need to ensure that we mark the file descriptor appropriately. Signed-off-by:
Trond Myklebust <trond.myklebust@primarydata.com> Tested-by:
Oleg Drokin <green@linuxhacker.ru> Signed-off-by:
Anna Schumaker <Anna.Schumaker@Netapp.com> Signed-off-by:
-
Chuck Lever authored
commit a4e187d8 upstream. Before commit 778be232 ("NFS do not find client in NFSv4 pg_authenticate"), the Linux callback server replied with RPC_AUTH_ERROR / RPC_AUTH_BADCRED, instead of dropping the CB request. Let's restore that behavior so the server has a chance to do something useful about it, and provide a warning that helps admins correct the problem. Fixes: 778be232 ("NFS do not find client in NFSv4 ...") Signed-off-by:
Chuck Lever <chuck.lever@oracle.com> Tested-by:
Steve Wise <swise@opengridcomputing.com> Signed-off-by:
-
Kinglong Mee authored
commit 3f42d2c4 upstream. Connection from alloc_conn must be freed through free_conn, otherwise, the reference of svc_xprt will never be put. Signed-off-by:
Kinglong Mee <kinglongmee@gmail.com> Signed-off-by:
J. Bruce Fields <bfields@redhat.com> Signed-off-by:
-
Trond Myklebust authored
commit 98b0f80c upstream. On error, the callers expect us to return without bumping nn->cb_users[]. Signed-off-by:
-
Boris Brezillon authored
commit ecbfa8ea upstream. scan_pool() does not mark the PEB for scrubing when bitflips are detected in the EC header of a free PEB (VID header region left to 0xff). Make sure we scrub the PEB in this case. Signed-off-by:
Boris Brezillon <boris.brezillon@free-electrons.com> Fixes: dbb7d2a8 ("UBI: Add fastmap core") Signed-off-by:
-
