- 25 Sep, 2014 39 commits
-
-
Saurav Kashyap authored
Signed-off-by:
Giridhar Malavali <giridhar.malavali@qlogic.com> Signed-off-by:
Saurav Kashyap <saurav.kashyap@qlogic.com> Signed-off-by:
Christoph Hellwig <hch@lst.de>
-
Joe Carnuccio authored
Signed-off-by:
Joe Carnuccio <joe.carnuccio@qlogic.com> Signed-off-by:
-
Sawan Chandak authored
Signed-off-by:
Sawan Chandak <sawan.chandak@qlogic.com> Signed-off-by:
-
Chad Dupuis authored
If we fail to load one of the segments of firmware fail the operation instead of trying to continue which will lead to a system crash since the pointers to the next segment will not be updated correctly. Signed-off-by:
Chad Dupuis <chad.dupuis@qlogic.com> Signed-off-by:
-
Chad Dupuis authored
Disable the PCI device during shutdown to prevent any races with other PCI code such as the AER handling code. Signed-off-by:
-
Chad Dupuis authored
Signed-off-by:
-
Himanshu Madhani authored
For FA-WWPN capable device, ISP2031 and ISP27XX, when loop dead is detected by a driver, restore WWPN from NVRAM. Signed-off-by:
Himanshu Madhani <himanshu.madhani@qlogic.com> Signed-off-by:
-
Chad Dupuis authored
Parse the retry delay timer field from the FCP response data and if: - It is not zero - The SCSI status is busy or queue full return SCSI_MLQUEUE_TARGET_BUSY for the number of milliseconds specified in the retry delay timer field. Signed-off-by:
-
Alex Vechersky authored
Signed-off-by:
Alex Vechersky <alex.vechersky@qlogic.com> Signed-off-by:
-
Chad Dupuis authored
Signed-off-by:
-
Nigel Kirkland authored
Signed-off-by:
Nigel Kirkland <nigel.kirkland@qlogic.com> Signed-off-by:
-
Himanshu Madhani authored
Nameserver data on FC switch is not refreshed when qla2xxx driver is unloaded. Disabling laser for ISP2031 will force FC switch to rescan ports and clear fdmi entries from Nameserver. Signed-off-by:
-
Himanshu Madhani authored
Signed-off-by:
-
Quinn Tran authored
Declaration error of mb array in qla2x00_iidma_fcport cause data to be written beyond the array. This ends up causing stack corruption. Signed-off-by:
Quinn Tran <quinn.tran@qlogic.com> Signed-off-by:
-
Sawan Chandak authored
Signed-off-by:
-
Arun Easi authored
Signed-off-by:
Arun Easi <arun.easi@qlogic.com> Signed-off-by:
-
Himanshu Madhani authored
Signed-off-by:
-
Himanshu Madhani authored
Signed-off-by:
-
Joe Carnuccio authored
Add support for the D-port (diagnostic port) fabric switch feature. (Fabric Switch initiates loopback style port testing) Signed-off-by:
-
Joe Carnuccio authored
Add support for the FA-WWN (fabric assigned wwn) fabric switch feature. (Fabric Assigned World Wide Port Name) Signed-off-by:
-
Himanshu Madhani authored
Add support for the FDMI-2 fabric switch feature. Since FDMI-2 uses code from FDMI-1, some of the existing code needed to be repaired to prevent fields from being overflowed. Signed-off-by:
-
Jan Kulich authored
Signed-off-by:
Jan Kulich <jan.kulich@qlogic.com> Signed-off-by:
-
Joe Carnuccio authored
Signed-off-by:
-
Joe Carnuccio authored
Signed-off-by:
-
Joe Carnuccio authored
Semaphore register does not exist for ISPFx00. Signed-off-by:
-
Joe Carnuccio authored
Call scnprintf() instead of snprintf() since the latter may return an incorrect count in cases where the write is truncated to fit. scnprintf() returns the count of what was actually written; snprintf() returns the count of what would have been written. Signed-off-by:
-
Joe Carnuccio authored
Signed-off-by:
-
Joe Carnuccio authored
When creating request/response queues from qla25xx_setup_mode(), the shadow index register pointers were not being initialized to point at the registers. Signed-off-by:
-
Joe Carnuccio authored
Signed-off-by:
-
Chad Dupuis authored
Signed-off-by:
-
Joe Carnuccio authored
Signed-off-by:
-
Joe Carnuccio authored
Signed-off-by:
-
Joe Carnuccio authored
Signed-off-by:
-
Joe Carnuccio authored
Since the entry call array is sorted in order of entry type opcode, the search can be terminated as soon as the search key is exceeded. Signed-off-by:
-
Joe Carnuccio authored
Signed-off-by:
-
Chris J Arges authored
When using a virtual SCSI disk in a VMWare VM if blkdev_issue_zeroout is used data can be improperly zeroed out using the mptfusion driver. This patch disables write_same for this driver and the vmware subsystem_vendor which ensures that manual zeroing out is used instead. Cc: stable@vger.kernel.org BugLink: http://bugs.launchpad.net/bugs/1371591Reported-by:
Bruce Lucas <bruce.lucas@mongodb.com> Tested-by:
Chris J Arges <chris.j.arges@canonical.com> Signed-off-by:
Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by:
-
Tomas Henzl authored
Add a call to pci_set_master(...) missing in the previous patch "hpsa: refine the pci enable/disable handling". Found thanks to Rob Elliot. Signed-off-by:
Tomas Henzl <thenzl@redhat.com> Reviewed-by:
Robert Elliott <elliott@hp.com> Tested-by:
-
Ching Huang authored
Signed-off-by: Ching Huang <ching 2048@areca.com.tw> Reviewed-by:
-
wenxiong@linux.vnet.ibm.com authored
Failing Device information are logged when IOA firmware detected these illegal request such as IOA firmware doesn't support inquiry with page code 2. The patch fixes the issue. Signed-off-by:
Brian King <brking@linux.vnet.ibm.com> Tested-by:
Wen Xiong <wenxiong@linux.vnet.ibm.com> Signed-off-by:
-
- 22 Sep, 2014 1 commit
-
-
Anish Bhatt authored
cxgbi_inet6addr_handler() can be called in interrupt context, so use rcu protected list while finding netdev Applies on top of core-for-3.18 Signed-off-by:
Anish Bhatt <anish@chelsio.com> Signed-off-by:
Karen Xie <kxie@chelsio.com> Fixes: fc8d0590 ("libcxgbi: Add ipv6 api to driver") Fixes: 759a0cc5 ("cxgb4i: Add ipv6 code to driver, call into libcxgbi ipv6 api") Signed-off-by:
-
